For the Driver NI-VISA Wizard error

Similar Questions

• How to start the wizard for the Driver NI-VISA development

  IM reading this manual:

  http://zone.NI.com/DevZone/CDA/tut/p/ID/4478

  I have labview8.6 on this pc, and I installed the driver NI-VISA 4.6... the manual says:

  "" "" 1. to open the DDW, select Start ' programs ' National Instruments ' VISA ' VISA Driver Developer Wizard.

  but the thing is, the menu of VISA, there are a few documents... There is no VISA Driver Developer Wizard... but I installed the driver NI-VISA 4.6... any ideas?

  In fact this explains the problem. You install DURATION VISA. If you re-run the installation program, you will see the feature tree seems different from that displayed a stone.

  The component you need, driver development Assistant, is in full VISA distribution, which you can download from the link below. The runtime is usually designed for deployed application. The development tools are absent of the runtime and are in the full distribution.

  http://Joule.NI.com/nidu/CDs/view/p/ID/1370/lang/en

• The driver NI-VISA Wizard and command of the SCPI

  Hello

  I had a go with an assistant driver NI-VISA. I wanted to create a driver for MH3114 DAQ. Assistant hollow went very well, and the driver has been installed.

  However when I did * IDN? under MAX, I received an error.

  This means that I have to create/put into practice all SCPI commands?

  How the wizard is designed to work?

  Hi MimiKL,

  As Dennis said, instruments are designed to work with the SCPI commands or not. If the user guide does not indicate the device meets SCPI and SCPI commands will not work.

  The wizard of the driver simply generates a number of screws that will send the standard commands of the SCPI compliant instrument of the SCPI. Depending on how you communicate with the instrument (bus), you may need to change these screws subtly to work with different instruments. But, as mentioned, if the device you are trying to contact is not in line with SCPI then this is never going to work. Later, when you use the Assistant driver, all the subVIs generated will be have comments in them tell you exactly what to replace and change to get the driver working for your instrument.

  If your device is not in line with SCPI and you have a dll that works then you should continue to use it.

  Best regards

  Chris

• The wizard of the driver NI-VISA creates drivers that are compatible with the 64-bit Windows XP/Vista version?

  The wizard of the NI-VISA driver creates drivers that are compatible with 64-bit Windows XP/Vista?

  InfiniteNothing-

  If you use a 64-bit compatible version of the NI-VISA driver, then the Assistant of the Driver NI-VISA is expected to create device drivers compatible 64-bit running in 32-bit mode.  You can find the various drivers of NI-VISA at http://joule.ni.com/nidu/cds/fn/p/sn/n23:1640/lang/en.

  Take care!

• Uninstall the Driver nor visa 3.0.1 to install 4.2

  Hi all

  I need to install the Driver or visa 4.2, but should I uninstall visa or 3.0.1 firstly to let the 4.2 to be effective.

  But I have some problems to uninstall the Driver nor visa 3.0.1.

  I wait your help for how to uninstall it.

  Thank you

  Thank you for your attention.

  I'm new on this. I just found how I can uninstall it from Add/Remove control panel part.

  Thanks for your time

  Problem is solved.

• The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1

  Intermittent crashes. The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1. How can I find this device? This is probably a hardware problem?

  I look at intermittent crashes, where my cursor becomes an hourglass and the system does not yet meet the ctrl-alt-delete.  In the case of a newspaper, I find

  Event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1.

  How can I determine which physical devices this is associated?  This indicates a hardware problem, or driver or firmware may be the source? The system has worked very well for a few years.  I'm not aware of any change in software that took place recently, although I have had by force, remove and reinstall iTunes earlier.

  I run SMART on all players controls and run diagnostics.  I ran chkdsk on the one I found the culprit, but not mistakes.

  Just in case it was a deadlock linked to memory, I tried to use the Diagnostics memory Microsoft on floppy, but it would not write on the disk (even if I could format and copy the files freely).

  Hello

  Go to your configuration and see which drive is for each port; 1,2,3,4...

  Then go to the Device Manager and look at how many SATA controller you have and how many ports for each, then start count from 0 to IdePort0, 1, 2, etc. for each SATA controller, so if you have 4 ports for each SATA controller, here is how you came from:

  IdePort0 1 -, 2 - IdePort1, 3 car - IdePort2 and road 4 - IdePort3 in the order of road by car

  I hope it helps

• The driver has detected an error of the controller on \Device\Harddisk1\DR1. What is the cause?

  I get this message on 7 11 windows event log IDs ' driver has detected an error in the controller on \Device\Harddisk1\DR1. "" The message keeps poping up when ever I insert my usb memory key but the DR number changes when I swap beetwhen and other memory usm drives exmp usb ports. "The driver has detected an error of the controller on \Device\Harddisk1\DR3." otherwise, my system is runnig perfect.

  Hello

  Check the drive for errors and see if it works fine it after.
  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors
  The link above includes steps for the same.
   $C God will not look you over for medals, but for scars. Each winner has scars; I do this either on the same heart

• Weird "cmd" option in the context menu for the drive/folder

  Recently, I noticed a strange 'cmd' (as what) command appeared in the context menu for the drive/folder. After pressing it, I get an error "this file doesn't have an associated program to perform this action."

  Efforts to eliminate this question nagging eye, using regedit and various 3rd party menu popup editors, have failed.

  Any ideas why this might have happened?

  Thank you in advance.

  So, I thought about it. It indeed is a corruption of the menu prompt integrated (that I didn't know existed until I started to search for this problem).  The problem and the fix is here:

  There is a key called "command" in HKCR\Directory\shell. Delete the key "cmd" under "shell", and then adding the following code appear to have solved the problem.

  [HKEY_CLASSES_ROOT\Directory\shell]
  @= 'none '.

  [HKEY_CLASSES_ROOT\Directory\shell\Command Prompt]
  'Extended '=' '
  "NoWorkingDirectory"=""

  [HKEY_CLASSES_ROOT\Directory\shell\Command Prompt\command]
  @= "@shell32.dll,-8506.
  'Extended '=' '
  "NoWorkingDirectory"=""

  [HKEY_CLASSES_ROOT\Directory\shell\Command Prompt\command]
  @= "cmd.exe /s /k pushd \"%V\"" "

• My Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1

  My computer (W7/64) sometimes fall to restart. I checked HD and the memory of Mrs. rescue disk - no error.
  Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1.
  The fact is that the cd-rom drive is behaving oddly. Reads the DVD of film without problem, but does not read floppy disks to install Windows (good on an another two comps).
  I therefore launched Verifier.exe and checked the other drivers. The result is dumpATA.sys is not running. (Is BTW not MS driver?).
  How can I force to load this driver?

  I checked the installation disc to compare the original version, boot.win opened, but the pilot is nowhere. Where did it come from?
  So I recorded the dump file, but the analysis of what this file is beyond my capabilities.
  Link to my file https://skydrive.live.com/redir?resid=4AF01405E5CE0354 dump! 114

  You could any body help me to find the source of my problem?

  Thank you.

  These are all good things:

  *****************************************************************************
  * *
  * Bugcheck analysis *.
  * *
  *****************************************************************************

  KERNEL_DATA_INPAGE_ERROR (7A)
  The requested page of kernel data could not be read in.  Usually caused by
  a bad block in the disk controller or paging file error. See also
  KERNEL_STACK_INPAGE_ERROR.
  If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
  This means that the disk subsystem has suffered a failure.
  If the status of the error is 0xC000009A, it means the query failed because
  a file system has failed to move forward.
  Arguments:
  Arg1: 0000000000000020, type of lock which took place (1,2,3 or PTE address value)
  Arg2: ffffffffc000009d, error state (state code of e/s normally)
  Arg3: fffffa80077f95b8, the current process (virtual address for the lock type 3 or PTE)
  Arg4: 0000000000000000, virtual address that could not be paged in (or the contents of the PTEs if arg1 is a PTE address)

  Debugging information:
  ------------------
  ERROR_CODE: (NTSTATUS) 0XC000009D - STATUS_DEVICE_NOT_CONNECTED
  DISK_HARDWARE_ERROR: Error occurred with disc material
  BUGCHECK_STR: 0x7a_c000009d
  CUSTOMER_CRASH_COUNT: 1
  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
  Nom_processus: System
  CURRENT_IRQL: 1
  LAST_CONTROL_TRANSFER: from fffff80002c7fcac to fffff80002c8bc00
  STACK_TEXT:
  fffff880 '03578-88 fffff800' 02c7fcac: 00000000' 0000007 a 00000000'00000020 ffffffff 'c000009d fffffa80' 077f95b8: nt! KeBugCheckEx
  fffff880 '03578-90 fffff800' 02c74ba7: fffffa80 '077f9550 00000000' c000009d 00000000 00000000' fffffa80' 077f95e8: nt! : FNODOBFM: 'chain' + 0 x 50080
  fffff880 '03578b 50 fffff800' 02c7e617: fffffa80 ' 07654b 50 fffffa80 '07654ba0 fffffa80' 077f9550 fffffa80 ' 077f95b8: nt! IopCompletePageWrite + 0 x 57
  fffff880 '03578b 80 fffff800' 02c8181d: fffffa80' 07654b 50 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiDeliverApc + 0x1c7
  "fffff880 ' 03578 c 00 fffff800 ' 02c4e4fb: 00000000 00000010' fffff800 '00b 96080 00000000 00000000' fffff800' 02c229a0: nt! KiCommitThreadWait + 0x3dd
  "fffff880 ' 03578 c 90 fffff800 ' 02c229fa: fffffa80 '07654b 50 00000000 00000001' fffffa80' 069ed040 00000000' 00000000: nt! KeWaitForGate + 0xfb
  fffff880 '03578ce0 fffff800' 02f29ede: fffffa80' 07654b 50 00000000'00000000 00000000'00000080 00000000'00000001: nt! MiModifiedPageWriter + 0x5a
  "fffff880 ' 03578 d 40 fffff800 ' 02c7c906: fffff800'02e06e80 fffffa80 '07654b 50 fffff800' 02e14cc0 00000000' 00000000: nt! PspSystemThreadStartup + 0x5a
  "fffff880'03578 d 80 00000000 00000000': fffff880'03579000 fffff880 ' 03573000 fffff880 ' 03578a 80 00000000 00000000': nt! KxStartSystemThread + 0x16
  STACK_COMMAND: kb

  FOLLOWUP_IP:
  NT! : FNODOBFM: 'chain' + 50080
  fffff800'02c7fcac cc int 3
  SYMBOL_STACK_INDEX: 1
  SYMBOL_NAME: nt! : FNODOBFM: 'chain' + 50080
  FOLLOWUP_NAME: MachineOwner
  MODULE_NAME: nt
  Nom_image: ntkrnlmp.exe
  DEBUG_FLR_IMAGE_TIMESTAMP: 5147d9c6
  FAILURE_BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080
  BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080

  And this page explains what you have:
  http://msdn.Microsoft.com/en-us/library/Windows/Hardware/ff559211 (v = vs. 85) .aspx >
  (Short version of an argument 9 d: "0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective wiring or in bulk, termination or that the controller does not see the hard drive.")

  It seems to intimate that it's a hardware problem rather than a driver. You say that you are having problems with the optical drive. If you log out, you still have problems to restart or boot?

  This probably isn't a memory problem, but a better method of verification, it is with Memtest86 + http://www.memtest.org/#downiso>
  Download the ISO and then create a CD with it and boot from it. If you have more than one piece of RAM, pull all but one test, then close, replace it with another and test, etc. I find it a little faster than the test at a time.

  SC Tom

• Need new firmware for the drive (Mat * un UJDA750)

  I have a Satellite M30 with a carpet * a player combined UJDA750. Anyone know where I could get a new firmware for the drive?

  THX.

  Hello

  I put t know why you need a firmware for your combo drive.
  As far as I know the carpet * a combo UJDA750 driver works with the Windows driver very well.

  Good bye

• I'm looking for the driver for canon cp400 pour windows 7

  I'm looking for the driver for canon cp400 pour windows 7

  Hello

  See this page to select your language:

  http://support.Microsoft.com/common/international.aspx

  ====================================

  Or sorry that it is area English.

  Left click at the bottom of the Microsoft Community page

  English and set your language.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Try to download Acrobat Pro XI, get suite error regardless of the drive that I select: "error".

  Try to download Acrobat Pro XI, get next error regardless of the drive that I select: "Error 1327: invalid drive...". »

  Hi pastorjeff7878,

  Please follow the steps mentioned in the KB: http://helpx.adobe.com/creative-suite/kb/install-error-1327-invalid-drive.html .

  Kind regards

  Romit Sinha

• There is a problem with the driver for Ralink Bluetooth PCIe Adapter. The driver must be reinstalled error code 39.

  HP Pavilion 17 laptop

  There is a problem with the driver for Ralink Bluetooth PCIe Adapter. The driver must be reinstalled.

  OT: Driver help

  Name:	PCIe Ralink Bluetooth adapter

  Error code:	39

  Hello

  Thanks for posting the query on the Microsoft Community Forums. You have reached the right place. Let us work together to find the cause of this problem and try to solve.

  What is the number of full model of the laptop?

  39 error code means Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. To resolve the problem, you will need to uninstall and reinstall the drivers for Ralink Bluetooth PCIe card on the manufacturer's Web site.

  I hope this helps. Let us know if you have other problems with Windows in the future.

• Setup error; call to the driver package install returned ERROR 1168 for package

  C:\Program files\hp\hpenvy120series\driverstore\pipeline\hpvp109.inf

  REQUIRED FILE 'serscan, sys' Windows cd is necessary

  type the path where the file & then click ok

  copy the file to

  C:\Windows\Inf

  This all came open when trying to install wireless software and set up the new printer. HP envy 120F-all-in-one model czo22a

  my computer came with windows vista home premium and has been upgraded to windows home premium.

  I believe that this file was lost during the upgrade because it is found on the new disk to upgrade to windows 7.

  up to present hp & Microsoft do not give me an answer

  set up the new printer wives without problem Toshiba

  If anyone can help me get the missing file give you considerably a ty

  Otherwise, I don't know if I'd come back printer?

  [Moved from comments]

  Hello

  1-the place where you paste the file?

  2. How do you install the printer driver (CD-ROM or by download online)?

  Please download and install the driver from the link and check that it works very well.

  Check out the link:

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=5203209&prodTypeId=18972&prodSeriesId=5203208&swLang=8&TaskID=135&swEnvOID=4062

  I suggest you to contact HP for assistance. They should be able to help you.

  Check out the link:

  http://h30499.www3.HP.com/hpeb/

  For all windows questions do not hesitate to contact us and we will be happy to help you.

• Assistant of the Driver NI-VISA is compatible with Win7?

  Hi all

  I was wondering if NI-VISA is compatible with Win7, because I want to use it to configure my device. Thank you.

  Here is the link for the latest driver VISA which includes support for Windows 7:

  NI-VISA 4.6.2