FPGA read/write does not not in cRIO-9073

Similar Questions

• SIM card reader/writer does not work?

  The card reader present in the /devices of control panel and of the printers on the e drive, but it won't work.  Any help please?

  You can buy external USB card for as little as $2 readers these days in most of the stores selling computers.

  Good luck.

• CD/DVD drive reads but does not write.

  I run XP multimedia.

  When the optical drive no longer works, I ran malware controls, then Mats_Run.dvd.exe.

  "I had to choose and choose fix' reading discs ' which it did.

  "" Write function did not work so I ran /Mats_Run.dvd.exe again with the ' writing difficulty ' option.

  Still, it reads but does not write.

  I installed an external burner and repeated the above; same result.

  When I boot with Vista, the two burners work perfectly.

  Details of virus removal
  Provided by: Malke - MS MVP:
  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  Also:
  Unexplained computer behavior may be caused by deceptive software
  http://support.Microsoft.com/kb/827315

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• Reading TCP does not detect the network closed conncetion error (66)

  Hi dear all,

  Instead of LAN I use WIFI to connect PC and mobile. Read all communications and write operations are performing ok. But the only problem I am facing is that once I disconnect the network from a mobile phone connection my labview TCP read operation does not detect it and only timesout at the specified interval. Although for Bluetooth connection network if I disconnect mobile then BT read detects it as network conncetion closed in error by peer (66).

  Can someone help me on this.

  Thank you & best regards

  Zdzislaw qureshi

  Hi Zdzislaw,

  The behavior you're seeing is expected for TCP as the device will timeout while it is looking for the connection close the connection.  This Wikipedia article explains how TCP protocol works in relation to a handshaking procedure four lanes running in order to close a TCP connection.  I hope this helps!

  Kim

• County to return read VISA does not match number of bytes

  I encounter an error with a VISA reading.  I ask 8 bytes (in number of bytes), but get only 7 return (return number), which causes errors in my code downstream.  Curiously, the VISA Read block does not return an error.  Any ideas on how to debug this?

  Data sheet:

  LabVIEW RT 8.2

  VISA 4.3

  Series OR 3.3.0

  PXI-8431/4

  Parameters: 1843200 Baud, 8N1.

  Is VISA reading set to put an end to the reception of a termination character?  I think that it does not have the stop in the output string character, which could make your short back counter.

  Lynn

• What can I do to remove a box pop up indicating "Message from Web page" and the message reads "object does not support this property or method".

  What can I do to remove a box pop up indicating "Message from Web page" and the message reads "object does not support this property or method".

  Hello

  1 how long have you been faced with this problem?

  2 have you made changes on the computer before this problem?

  3. when exactly you get this error message?

  The following threads may be useful:

  http://answers.Microsoft.com/en-us/IE/Forum/IE8-windows_other/message-from-webpage-not-implemented/d09fa331-92c6-4CD3-bc89-9a2c03e304fe

  http://answers.Microsoft.com/en-us/IE/Forum/IE8-windows_other/message-object-doesn

• When I try to burn a music disc player is registered as a DATA reader and does not allow me to copy music files that I can play on an external source

  I have computer aGateway running Vista Home Edition and something happened with WIndows Media Player.   I have the DVD/RW internal drive and external DVD/RW as a player.  I use them mainly to copy music files and it has always worked fine until yesterday.

  When I try to burn a music disc, the player is registered as a DATA reader and does not allow me to copy music files that I can play on an external source (such as the CD or car drive).  Worked fine Saturday and had burned discs Saturday night recognizes the two drives as data drives.

  Is it something that needs to be reset or changed?

  In WMP, please click the button burn up and make sure that the Audio CD is selected. Then try burning the CD again, they now play on a standalone CD player too.

• ENE PCI Secure Digital / MMC Card Reader Controller does not

  ENE PCI Secure Digital / MMC Card Reader Controller does not

  I suggest that you go the manufacturer of your computers website and search for drivers chipset update.

  Click Start, type: Device Manager

  Press enter on your keyboard

  Click with the right button on the controller listed in the tree view of the devices

  Click on uninstall

  Restart your computer and let Windows redetect.

• Adobe Reader 11 does not print PDF documents for printing of attachments in PDF from Outlook 2016.

  Adobe Reader 11 does not print PDF documents for printing of attachments in PDF from Outlook 2016.
  Version of Adobe Reader 11 11.0.13 has been uninstalled and reinstalled. Print PDF documents registered in the system but not when opened as an attachment.

  Any ideas?

  HI Steve,.

  Please try to use the CD player with office 2016.

  Uninstall cleanup tool: Download Adobe Reader and Acrobat tool - Adobe Labs

  Install using offline Installer: Adobe - Adobe Acrobat Reader DC Distribution

  Thank you

  Abhishek

• I have a mac / downloaded adobe reader and does not accept the license agreement for end

  I have a mac / downloaded adobe reader and does not accept the license agreement for end.  It says successfully downloaded.  I'm going to use it and it won't work.  Told to close.  I opened adobe reader software and brings me back to install which I knocked again, and he says already installed.

  I closed out of all tabs, went to "safari" in the top of the page, clicked on close safari.  I clicked on Go, and then click applications, then I found adobe down and clicked on it.  then he gave me a place to click on accept.  I hope it works!

• my adobe reader software does not work properly always receive a message (not), why?

  my adobe reader software does not work properly always receive a message (not answer), then on the right Circle loading then suddenly stop and then become white background as shown below, why?

  I can't read any pdf file and I try to update the adobe reader and acrobat software, but nothing has changed.
  

  
  

  My (certainly old and slow) system made too the first time I opened 11 player, but he "thawed" after fifteen seconds, (an eternity in computing time, I know, but it has finally opened completely) what you see to the right is the "Tools" palette during initialization. That's exactly where mine would freeze at startup. Once he finally opened fully, I clicked on the "Tools" link at the top to close the Panel, and I opened and seen a document in this way and then closed reader. Now when I open the drive, the tool palette is not initialize and it opens immediately.

  Restart and prior to open what any else, open the drive. When you open it, DO NOT try to do anything with it until it fully opens, do not click on anything that it either, do not try to switch to another app give it time to open up completely and then click the tools link to close. Then open and view a document and close it. Close the player and reopen it. the tools Panel should stay closed and reader should open completely immediately.

• Frequency of calls to control for the FPGA read/write

  Hello

  I use a cRIO-9076 with a module NI 9476 DO spend some faucets. It is sometimes necessary for faucets with a pulse time down to a few ms of impulse.

  The FPGA VI Gets the power tap queries, executes a logic of security, and routes the numerical results for the exits. It gets applications power of the VI on RT target that uses the function ' Read/write FPGA control' interaction programming of the FPGA VI front. The loop on the RT runs with 1 kHz, no iteration is missed. That means, it should be possible to switch the valves with a resolution of 1 ms.

  What I see on an oscilloscope, is that the output digital are high for multiples of 50 ms, the system does not reach the valve for example 80 ms pulse or pulses shorter than Ms. 50 is a kind of limitation for calls of "FPGA read/write control"? I tried both options for arbitration, but it does not help.

  The best knowledge of the limiting cRIO/module/features or ideas? Thank you in advance.

  Karsten

  Hi Karsten

  You use any time in your FPGA VI?

  It is useful to your code by sending as an attachment so that I can have a look.

  Kind regards

• HP DVD Writer does not read or write DVD, but only the CD

  My HP DVD 1135t burner does not read or write DVD but only the CD. What is the problem? Please help me.

  CD/DVD players use different lasers for reading/writing DVD from the CD.  All indications would point to your laser DVD as having failed.  You could try to remove your drive and install it in another computer to see if the problem follows your player or your computer, but my bet is that the drive must be replaced.

  HTH,
  JW

• I have PC toshiba laptop, my cd/dvd. writer does not read the CD software and not able to write the media__

  itshow msg

  Insert the disc pls

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  ===============================================================

  Check with Toshiba support, their drivers online (update or reinstall) and their forums.

  Toshiba - Forums
  http://laptopforums.Toshiba.com/

  Toshiba - Contacts
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contact

  Toshiba - drivers - access your model
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download

  Toshiba - Support
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• TECRA M9 card reader still does not not with Vista SP1

  Why Toshiba didn't supply of integrated drivers for the card reader M series for people who do not want to run the Toshiba version recompiled Vista, which allocate Inc. of the unwanted software like Norton to slow down the Vista system!

  Im running a clean install retail Vista x 86 with updates, but 1-2-4 & 8gig sd cards will not work!
  in Device Manager it says "the device cannot start code 10".

  IM also beta SP1 which will detect the SD card, however cannot you read/write on the SD card.
  An update of the factory of the SD card reader Vista is whats needed!

  Hello, Robert

  At first, I must say that you are completely mistaken.

  The first Toshiba does not force someone to use the recovery image only. You can install your own version of Vista at any time. I also installed Vista Ultimate on my laptop. I also installed the just necessary drivers, download page of tools and utilities following the Instructions of facilities of Toshiba document. I hope just do you the same thing.

  As you wrote that you are on the tests of SP1. I also believe that Toshiba is also on the tests because SP1 is still beta version and so far not implemented the recovery image. Up until Toshiba offers no support for SP1. I can imagine different things will not work properly and Toshiba that will probably correct with the new drivers for the problematic hardware components.

  In the end, I can say: you can use your own OS installation like me and thousands of other owners of Toshiba laptop.