Front 2 USB not working properly

Similar Questions

• Peripheral USB not working properly

  original title: no

  my USB doesn't work when I plug it into any device. wireless mouse or everything usb will not turn on.

  Hello

  If a PC (not a laptop) the port USB can be replaced if necessary with a card and they are not expensive.
  A laptop would need a computer store real (no leeks and glances at a BestBuy or other BigBox
  Stores) or system manufacturer support.

  Check / settings (BIOS/CMOS) often F2 when you start screensaver - make sure that the embedded USB
  is activated.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
  all except the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and the method of Vista is identical
  http://support.Microsoft.com/kb/310575

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• G7-2320dx Pavilion: USB not working properly

  I have Windows 7 Ultimate x 64 and for some reason, on the g7-2320dx Pavilion, and I have a USB keyboard and mouse.

  But for some reason, the only port in the keyboard/mouse is that the charger (I think it is usb 3)

  Before I demoted, I used the USB ports on the left side of the mouse and one on the right of the keyboard.

  I know there must be a pilot for him somewhere, thank you very much in advance.

  Hello:

  You need the amd chipset drivers, if you want the USB3 ports to work...

  http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064

• Mouse - touchpad and USB - HID - does not work properely on Satellite L40-139

  The mouse is very unstable. Mouse touchpad both usb do not work properely, but the touchpad a little better. It happens that, even if the mouse using USB to the point does not move, while the left and right button are always react.

  It is brand new computer (L40-139) with initially installed Windows Vista. How can I solve the problem?

  It is very disturbing. Thank you.

  Hello

  have you ever tried to recover your machine, which means a complete reinstallation of your system? First: to exclude the material errors, you must perform this step, and if the error persists, then I suggest you to contact a service partner chartered for a checkup of material and a repair action.

  If the problem occurs after reinstalling windows, visit the following link to find the closest to the ASP available in your country:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  Greetings

• Error of USB host - peripheral controller is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title - USB - IF xHCI USB Host Controller

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I have a permanent error on my computer and when I run the troubleshooter I get the above message.  It says Windows cannot load the driver.

  Hello

  USB devices remove all you can - restart the computer - is still there, the error? If it isn't
  It is related to one of the add-in devices that you removed. If she is still there, then, the question is
  either a device internal who can not remove or physically with the USB bus itself.
  If it was not there, add devices at a time until it is displayed - keep in mind that it is
  possible that there are two (or more) devices in conflict over the issue. Once you
  identified the check of the aircraft with the help of the manufacturer.

  1. to find the control panel - device - device - right-click on it - uninstall - Manager then
  Restart the computer to see if it clears.

  2. same place - double click on the device - driver tab - driver update - to see if that helps.

  3. check with the support of system manufacturer (manufacturer of motherboard for customized systems), their
  online documentation and drivers, diagnostics and ask questions in their forums on all known
  questions. Update the Bios and chipset or other USB drivers.

  =====================================

  If necessary, we will use these additional troubleshooting methods:

  How to fix Code 31 errors
  http://pcsupport.about.com/od/findbyerrormessage/a/code-31-error.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Media Center won't play by video converter USB error ""files needed to display video are not installed or not working properly. " Restart the computer or Media center.

  I use USB to HDMI. TV, it is attached to works very well with the screen of the PC, but not with windows media center. Get the error message "the files needed to display video are not installed or do not work properly. "Restart Media center or computer" whenever I have to plug the usb device and you try to play a video in wmv recordedTV. Otherwise, it works fine on the PC monitor. What is the problem? Can it be fixed? I use questions cable 'Câble questions SuperSpeed USB 3.0/2.0 to HDMI/DVI for Windows and Mac up to 2048 x 1152/1920 x 1200' with windows 7. Is there another brand and model that works?

  On Wednesday, September 3, 2014 13:19:09 + 0000, CharlesHickox wrote:
   
  > I use USB to HDMI. TV, it is attached to works very well with the screen of the PC, but not with windows media center. Get the error message "the files needed to display video are not installed or do not work properly. "Restart Media center or computer" whenever I have to plug the usb device and you try to play a video in wmv recordedTV. Otherwise, it works fine on the PC monitor.
   
  I assume you mean WTV and not the WMV files? Likely the reason is that the adapter
  questions of cable is not HDCP compatible. (Rules of DRM Media Center
  apply).
   
   
   
  __________________________________________________________________________________________________
  Barb
  MVP Windows Entertainment and connected home
  My Blog - http://digitalmediaphile.com/
   
  Please mark as answer if that answers your question
   
   
   

• USB drivers do not work properly.

  I have a netbook Vaio (name of the VPCM13M1E model) and USB drives will not work correctly. I ran a microsoft fix (hardware and devices one by one). The results said:

  -universal host controller USB Intel (r) 82801g (ICH7 family) - 27 8 does not work properly, and it has not been fixed.
  -Intel (r) 82801g (ICH7 family) USB2 enhanced host controller-27CC does not work correctly, and it has not been fixed.
  -Hardware changes may not be detected.
  Its very annoying because I cannot plug anything on the USB.
  Help, please.
  Camille

  There was a lot of mistakes in the case where the display indicating a gel delivers that seems to have started in early April.

  These gels seem to be preceded by the following error (Source - core-EventTracing):

  Session "Microsoft Security customer OOBE" stopped because of the following error: 0xC000000D

  This error can be caused by a corrupted EppOobe.etl.

  You may be able to resolve the freeze by recreating the EppOobe.etl.

  First of all, can you do the following:

  Start > type options files in the "search programs and files ' and press 'Enter' keyboard > view > then under" Hidden files and folder "select"Show hidden files and folders and drives"> OK

  Then go to the following folder:

  C:\ProgramData\Microsoft\Microsoft Security Client\Support

  In this folder click EppOobe.etl , and then rename the file in EppOobe.bak

  Restart the computer and let Windows recreate the EppOobe.etl.

  I hope that will stop the freezing issue.

  If the problem persists with USB you can restart the computer using safe mode and see if the problem exists in Mode without failure.

• SD card is not working properly after installing windows 10

  I have a MacBook Pro (retina, 13 inches, early 2015) with EL Capitan 10.11.5 and after I installed 10 windows using bootcamp, everything worked fine at first, but after I deleted my part of windows and then installed windows 10 the second time, the SD card is not working properly. She mounts only if the computer shuts down first, and then start. If I take the laptop directly, the SD card will not rise. The same thing happens when I switch systems using a control option key or bootcamp Center where when I switched to another system, the SD card that was mounted on the old system does not appear in the new system. I was trying to solve this problem remove the part of windows before you reinstall it again once, so I found that after I deleted the windows part, the problem is gone and it reappeared after installing windows 10 even once. I also found that after I installed windows the total volume of hard drive (128g front) became 121g.

  Hello LorinMax,

  Thanks for this info and choosing the communities Support from Apple. I know the importance of your work with your Macbook Pro SD card!

  If I understand correctly, you cannot use your SD card, unless you stop and then restart. Because this behavior started when you installed Boot Camp, I would start with the following steps:

  1. first of all, start by repairing your hard disk in disk utility to correct the unexpected problems that could be the cause of this behavior.

  Disk utility (El Capitan): a disc repair

  2. use Mode without fail to start up your Mac so that it performs certain checks, remove files from the system cache, check your startup disk and trying to fix problems if necessary directory.

  Try safe mode if your Mac does not end commissioning

  Graphics performance limited in recovery of OS X or in safe mode

  3. According to Boot Camp Installation & Setup Guide, you may need to back up your personal data and reinstalling OS X, then reinstall Windows via Boot Camp and related support files.

  Boot Camp Installation & Setup Guide

  Backup of your Mac hard drive

  OS X: on OS X Recovery

  See you soon!

• Keyboard does not work properly

  Hello

  I had trouble getting my laptop satellite to initialize. Recovery disks & pressing F keys weren't working so I decided to open the laptop to see if there are any loose connections. To my surprise, the laptop seems to work again once I had the USB keys and put back them in! Unfortunately, before that I did, I opened the keyboard and peeked inside.

  When I booted up and tried to use the keyboard keys half of their work and the other half seem to think that they represent two other keys for example if I type the letter 'E' I get '3' and '-' as a whole. After 5-10 minutes the entire keyboard will become totally unresponsive until I restart again. Of course, I think I've done something here because this problem since I opened the bottom of the keyboard. This could be a hardware failure I have caused or is anyway that this issue can be resolved without replacing anything?

  Thank you very much

  Tom

  Hi Tom

  Theoretically, it might be just a connection lost between the keyboard and the motherboard, but I'm afraid, it can be a serious problem of m.
  Maybe you have damaged the connector of the keyboard cable or something similar, and not the keyboard does not work properly.

  I think the keyboard needs to be replaced to check if only this part is affected

• Satellite L670 - after Win 8 upgrade WIFI does not work properly

  Afteer upgrade to Win 8, the WiFi of my Satellite L670-128 has stopped working properly.

  The connection only works some time, usually only a few seconds before the connection is lost.
  After a few seconds or minutes the connection is restored, just soon to be lost again.

  Cannot download large files or even to see larger photos on normal web pages. Is there any Win8 driver for Broadcom coming 802.11n network card, or should I throw one 2.5 year old computer in the trash?

  Buy a usb-wlan card is not an option, as wireless mice is already "permanently" reserving one of the three usb ports and wlan card it would be just to the left...

  To my knowledge this L670 series isn t Win 8 taken in charge and this means that there is no special Win 8 drivers for this device, so I put t think you will find an another Win 8 driver for this WLan card.

  But do you really want to throw this laptop in the trash just because the wifi does not work properly running Win 8?
  The device was working properly under Win 7?

  I would recommend running a few Wlan test.
  For example; Disable wireless encryption on your router and Wifi connectivity with the open network do that just for testing purposes, perhaps you will need to change the type of encryption to test.

• Satellite P25-S520 - DVD player does not work properly

  Difficulty of DVD player or buy the external drive

  My DVD player does not work properly, in fact it can never work properly. Recently, I tried to back up my PC on a DVD using Norton 360. Norton did not recognize that the DVD was present. Then I tried to write a text file on a DVD and was a failure. DVD + R and DVD-R media were found to be (Maxwell 16 X).

  I could have probably lived with this however, I received a copy of Dragon NaturallySpeaking version 10 on a CD and my Toshiba would not recognize it. I tried the CD in my laptop nearby and it was recognized.

  An attempt to update the driver has also fails.

  I was able to copy a CD of music last night so that at least works properly.

  Does anyone know how can I fix? The important part is to be able to load my new program.

  Research on some forums I found that other people have had problems with the Pioneer drive. If the drive can't be fixed, I'm not adverse to buying an external DVD drive. Unfortunately, where I live there is no brick and mortar stores selling external drives and I prefer to avoid the hassle of getting a drive online and discovering that it does not work with my Toshiba. Can someone suggest an external USB drive that will read and write CD and DVD and is certain to be compatible with my Toshiba?

  Thanks for any help,
  Humbaba3000BC

  Satellite P25-S520
  PIONEER DVD - RW DVR-K12D
  Driver provider: Microsoft
  Driver date: 01/07/2001
  Driver version: 5.1.2535.0
  Digital signer: Microsoft Windows Publisher

  Any external USB CD/DVD drive will be compatible with your laptop.

  However, you won't be able to boot from CD (run recovery for example) If you are using an external drive.

  So, your best option would be to replace the internal drive with a Toshiba drive designed for the laptop. Call an ASP and request a quote.

• My laptop HP keyboard does not work properly.

  My laptop HP keyboard does not work properly. First of all, it makes a clicking dull when I type, second if I type (anywhere) it wont let me repeat a letter or any key back to back with waiting 2 + seconds. It comes with the connected keyboard or a usb keyboard. How can I stop this?

  In the Panel-> Accessibility-> make your computer easier to use-> make the keyboard easier to use, check your filter keys, if it is on, turn it off.

• This device does not work properly because Windows... this device. (Code 31)

  Hello buddies, how to solve this problem (code 31)

  USB does not work on my PC, I found that it was the problem of the unit. and he wrote that this device does not work properly because Windows cannot load the drivers required for this device. (Code 31).

  How can I solve this problem?

  In addition, you can check the following registry key? :

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ (36FC9E60-C465-11CF-8056-444553540000)

  Is there a 'name' UpperFilters and LowerFiltersin the registry for this key, in the right window?

  If so, what is 'Data' for these names?

• Generic adapter Bluetooth is not working properly and network controller has no driver

  I use the version ultimate windows 7 in my computer dell laptop inspiron n5110.

  After reloading the OS, I started to deal with the following issues:
  
  
  Generic adapter Bluetooth is not working properly
  Windows has detected a problem with the generic Bluetooth adapter.

  The device information: generic Bluetooth adapter

  ID: USB\VID_0CF3 & PID_3002\6 & 58952F4 & 0 & 4

  Error code: 43

  Network controller is not a driver

  There is no driver installed for the network controller.

  Name: Network controller

  ID: PCI\VEN_168C & DEV_002B & \001517FFFF24141200 SUBSYS_02051028 & REV_01

  Error code: 28

  You will need to download and install the drivers from here:

  http://www.Dell.com/support/drivers/us/en/19/product/Inspiron-15R-n5110

  Choose 32-bit or 64-bit, depending on what you have.

  SC Tom

• My Apple TV remote 3rd generation A1294 doesn't aluminum A1394 does not work properly, the battery is and I have tried all the resets including factory reset.

  My Apple TV remote 3rd generation A1294 aluminium does not work properly, battery is good, and I tried all the resets including factory reset. the battery compartment is clean.

  You don't say what you mean by not working not properly, however...

  Your Apple TV can become affiliated with another remote control. Hold the remote control close to and pointed on the Apple TV, press and hold the menu and rewind buttons together for 6 seconds or until you see an icon of the chain broken on screen.