front panel size between decoration

Hi all

Does anyone know if there is a way to size, a façade based on a decoration.

for example, I have a front apnel GUI with a flat frame decoration.

I spent some time tweaking the front panel to show what is inside the flat frame decoration.  I go back and change some stuf and repeat these optimizations.

It would be cool if I could just put highlight the object of decoration and tell the VI to resize based on the decoration.

I tried this VI-> Panel-> Decos []-> Index [2]-> MasterRect to set the FP. PanelBounds.

It is assigned the same size as decoration, but not really where the decoration, see VI attached.

Any ideas?

-Sean

You must set the origin of the part of the façade as well.

But as Ian said, it is probably best to design your front and your decoration so that its located at 0,0 and place in upper-left corner of the window.

Tags: NI Software

Similar Questions

  • The front panel scroll, based on the size of the monitor

    Hi guys,.

    I built an exe file of a VI on a labview having machine so that it can be run in another has no labview. The machine where I programmed the VI has a large 22 "monitor and so I put on my face as a result. The machine that will use the exe file has a screen size of 15 ", and some elements of the front panel are not accessible if I make an enlargement. However if I don't maximize the screen I can move the window to the edge and access controls. But it's so heavy. Is there a way I can add scroll bars to the VI while I can scroll the front panel?

    Thank you

    Of course.

    Scrolls bars are something that you can turn on (and are normally enabled by default) in the dialog box properties VI of VI.

    In addition, it is usually best to design your sign before and that it is effective for the smallest screen size you expect that it runs.

  • HP Z620: Front panel connector pinout

    Kindly help me on what is the pinout of front panel to motherboard HP Z60 connectors? Nothing is indicated on the map.

    Here is the motherboard front pinouts.  This is a view of the motherboard.  PIN 6 is the key, a missing brooch, which helps determine the orientation of the connector.

    The Z420, Z620, Z820 and all have the same front panel connector pinout.

    -Terminals 2 and 4 are for the power light.  HP systems have back to back LED connected between these pins.  A white LED lights up in red and a normal functioning (and flashes error codes) when there are errors.

    -Connect a switch momentary between pins 7 and 8 will turn on the computer and off.

    -The sensor pins are for a thermal sensor in cable from the front panel.  If it's sensor is not installed, the system fans will probably ramp at full speed and very noisy.

    -Speaker Out is the internal speaker.

  • Cannot resize the front panel

    I can't resize the front panel to a smaller window.  I put in (0,0) minimum window size, unchecked maintain proportions and to scale all objects.  I had originally put the size of the minimum window to 1012 x 616.  When I close the window property and re - open the settings still collated (0,0) while they are saved, but I am unable to reduce the size of window smaller than 1012 x 616.

    Also, there is open space on both sides in both dimensions, so I'm not running in the front panel objects.  What property/properties miss me that locks the minimum panel size?  One last thing is that I'm able to resize windows from any SubVIs I the same project and edit the minimum window size them and they respond as expected.

    Thank you

    Very strange

    comics ctrl + A, ctrl + C, ctrl + N, ctrl + E and ctrl + V solves everything.

    NOR should open with a debugger that vi... Oh where is that entry again heep peek ini thing...

    [Edit: here]

  • Any LabVIEW 2009 Front Panel Gage displayed as circle deg continues 360?

    Any LabVIEW 2009 Front Panel Gage displayed as circle deg continues 360? I want to display a position of motor on the Panel before LabVIEW as a circle of 360 degrees. Is there a way to make the pledge appears as a circle of deg continues 360?

    dbaechtel wrote:

    Gauges and dials, buttons, none of them seem to be designed for continuous operation of 360 degrees. Of course I can set the scale of 0 to 360, but I can't get rid of the gap between 0 and 360.

    How to set up a pledge to show a continuous 360 degrees without a gap between 0 and 360?

    To change the gap, take the line high marker and move it to the desired location (in another origin, enter the low marker).

    Also, don't forget to wrap the raw in 0.360 rank if it falls outside. Here's a quick example (LabVIEW 8.0).

  • scale multiple objects with front panel

    I have so many objects in the front panel. But I want only to certain items on the scale (IE need to keep the size of the button as it is). When I am trying to select the "Object of scale with the pane" option for each objects, it is available only for a single object. This option does not appear after that. Is there another way to do this?

    Hello

    Go here, this information will help you solve your problem

    http://digital.NI.com/public.nsf/allkb/048C31D73E8EC91286256E440063E1BB

    BR

  • Creating custom shaped front panel

    I want to create a popup in personalized form (other than the rectangular shape). For this I created a green façade (0x00FF00) background color, placed the shape I want as a background image. Now the unnecessary part is in green. I then used a function of windows (USER32. DLL: SetLayeredWindowAttributs) to the green of the transparent color. It works for me, but the question here is that it takes time to become transparent. For a fraction of a second, the green color is visible to the user. Is there another way to be a part of the transparent window?

    You will probably need to get it to keep the front screw closed/hidden until after he made the call to USER32.dll (and make that one of the first calls you make). It is probably your façade opening when the VI of loading display Input Panel began execution - or you might not be calling it right at the beginning of your VI so there is some delay.

    Oh - affecting the hidden Panel should work - there is a difference between closed (no front panel) and hidden (open, but not visible) - properties that can be performed on narrow front panels work usually on hidden. If this still does not work - you could try to move the position of the window off the screen (p. ex.-5000,-5000), show it, apply the property and then bring it back.

  • button arrow in front panel

    Hi guys,.

    I want to have an arrow in the front panel to control the operation of a number.

    Which means;

    If I press the arrow key to the left, the number decreases and arrow key to the right, the reverse occurs.

    I found a drawing of arrow under the decorations but cannot change anything with her.

    Basically, the arrow is sufficient to act as a Boolean switch.

    Once pressed, it lights up and the number accordingly runs and stops when letting go.

    I want to have the arrow keys to make the more presentable façade.

    Pls advice me to.

    PLs Note: I'm not using the keyboard to simulate on the front panel. It is purely on the façade.

    Thks N RDG

    Titano

    one thing you can do. I should work

    1. make a right click button in VI and select Advanced > customize

    2. then a window will appear where you can customize the button.

    3. click on the right button and select Import an image from the Clipboard > decal

    4. it should look like this (attached)

  • Delay in resizing of front panel

    Hello

    I develop GUI which needs to look nice and the user will have the option to resize. Since the ladder under the window property fails, I wanted to use the resize Panel event.

    But there is delay - controll is resized some time after I resize the front panel and that seems bad. When I look at the list of window or error of project it will resize instantly.

    Why I can't get this result in Labview?

    I could always sign size leash read say every 10ms and calculate the size of ontrolls on this basis, but is there best option by using this resize event Panel?

    It should be more or less obvious that this parameter means when used.  If you set a control to fit the pane and then resize this component, it does not wait for the mouse to start resizing it it will resize for each pixel the mouse movement.

  • How to call the shading on the front panel?

    Hello world

    Quick question and I was looking for, but I couldn't find on the front panel, but I have a waveform attached where I apply shading to the area between the two lines of standard deviation (see attachments).

    I was told that I could call him shading on the front panel by right-clicking, but I couldn't find it anywhere. Can someone please help?

    Thank you!

    TheLT

    Under fill options, you can fill in between different graphics.  To get there the legend graphic or through nodes of inter-generational

  • cRIO, Webservice (REST) and front panel

    Hello

    I created a few simple webservice screws for greater application that runs on a cRIO. The webservice screws can be used to send simple commands to the application and give your feedback. So far, I used a LV frontpanel for interaction with the system, but for several reasons, I am looking for another way to do it.

    It worked well in the development environment. After deployment webservice screw they have communicated with the application according to the needs and I am able to control the system using simple URL typed in the browser's address bar. Later, I will add static content, but for debugging, it is fine.

    The thing is that now I have compiled and deployed the application, and now when I try to open the front panel I get this error message:
    "VI requested is broken and cannot be read or controlled."

    Previously I did not use the Web OR Application Server, so I installed to use the web services. Are there conflicts between a Web application server and remote server Panel? Any suggestions on how to proceed?

    I use LV 2012 and NI RIO 12.0

    Best regards

    Simo

    Hi Simo,

    If I understand correctly, you have the following configuration:

    cRIO with a Web Service of LabVIEW and several Web Service screw

    Some ways to debug deployed screws of LabVIEW Web Service are:

    You can have the Service of the Web of LabVIEW deployed in debug and debug remote Web Service of LabVIEW desktop.

    You can use a tool like factor to make it easier to apply and test your Web Service screw (similar to go to the url in the browser).

    You can create LabVIEW screws of office using the Palette of HTTP Client to test the Web Service.

    You mentioned the following"I have compiled and deployed the application, and now when I try to open the front panel... "

    I'm a bit confused as this front panel you open. For example, do you mean that a LabVIEW project has been opened on the desktop, the Web Service of LabVIEW in the project has been deployed to the target of RT cRIO, and now, when you open the Web Service screw on the desk to look at the front panel, you get an error message?

  • Freezing of front panel

    When I run my VI it will sail between the tabs and the front panel will not freeze if I do not enter the voucher code and simply press the home button.  However, when I enter the voucher code (1234), then the program brings back me to the Home tab but then freezes the front panel.  I tried running without highlighting the execution until I have enter the code and quickly press the bulb to see run step by step and when I do that it goes back to the home screen and that it does not freeze so I paint a white on why it freezes.  Any help would be greatly appreciated!

    I am new to Labview, so I don't know that my code is poor.

    Your code is backwards.  Why is the case your outermost structure structure?  In which case runs is determined by which tab is selected when you press the run button.  The while loop must be the outermost structure.

  • Disabling the controls on the front panel

    Hello

    Currently, I am working on trying to disable/gray out between 10-20 controls on the front panel when you press a start button and then allowing them the end of the test. Currently I use the property nodes, all of which are connected to a constant of the State in which I want that works perfectly. My question is that there is another way other than having a bunch of knots of padding property to the top of my structure of the event. Ive read where people had Subvi, which has used references to make this same feature, but is there a way of doing things in the block diagram of my current VI? Thank you!

    Need references of your controls on the front panel, so this can be fast, because you can select more than one, and with a right click you create references.

    I have attached a version LV2010.

    Edit: another review:

    Must be created only once these references. Usually, it's comfortable group all the references in a cluster, use this thread through your entire code. This way you can just ungroup references to the actual location, you have to play with, put them in a table and use the above FOR loop to change their properties...

    Like this:

  • Sizing of the 50 orders/lights on the front panel to look like

    Hello

    I have 50 rectangular bollean indicators on the front panel. For some reason, the sizes of a few indicators are slightly different from the others. If I resize with the mouse it oversizes it. Can't think of an intuitive method to achieve this.

    All the ideas!

    Kind regards

    Austin

    Resize objects-> Minimum Height and Width.  or is it Minimum Width and Height, I forgot...

  • PNG resize problem on front Panel (not stripped)

    I'm having a problem trying to develop custom controls and expand my GUI beyond the default options Labview.  I'm using a Visio flowchart to illustrate an industrial process.  I encountered a problem trying to add items such as indicators of tanks to the façade.  To do this, I'm importing Visio images, in photoshop and then saving them as png to maintain transparency.  The problem I have is that when I drop this file .png on the front panel and resize, Labview seems to be falling pixels and cut the edges of my image.  This seems to happen on which corner I resize the base.

    Example:

    Sample PNG bumped against a new front and then resized using the building in the container box.

    I have the same problems with the .gif files.  I have reviewed the various .png and .gif export options, and I don't see anything that I'm missing.  I don't have a problem with JPEG files, so it must be something related to transparency.  Is this a known problem or there at - it a labview option, I'm missing?  I am currenlty using Labview 2010 SP1.

    Given that I'm still in phase of my development of gui layout, I don't know the exact dimensions of all my items and I was hoping I'd be able to resize it as I'm going to and not to be completely locked in at custom controls.  Any idea would be appreciated.  I searched the forums, but all the questions that I could find were mostly programmatically resizing problems.

    One option, you can try exporting the EMF or WMF image. LV should be able to import that, and because it is a vector format, in my opinion, it should also resize correctly.

    Another alternative is to draw in BT itself, either decorations or control of image to draw programmatically (although you should be aware that this option can have performance issues).

Maybe you are looking for

  • Change the cover Photo in the Photo Albums

    Hello... My message all in the apple community. New amounted to apple, and my first purchase is an iPhone 7. Loving the camera and he can do with photos. How can I change the picture of an album cover that I created...? I've read a lot online, but al

  • Tecra M9 - peripheral unknown.

    Hi guys,. Just wipe the base that was on my Tecra, install no problem with most of the drivers had obtained most of them since the Toshiba download pages. However, I am really puzzled with one device and its beginning to my nerves now! I searched the

  • How can I remove this virus 'shortened '?

    I've got pctools and it did not detect this virus.  One day the screen went white and I got was a blue screen.  I have now a few basic icons, but even the programs have been removed from the menu all programs.  Some of my files are too gray.  I check

  • Windows 7 in a deadlock

    Hello I just bought a new PC from Amazon zoostorm. It said in the description that there windows 8, but when I got it I realized he said elsewhere that it had no operating system. I downloaded an iso of Windows 7 and I bought an Amazon license key (I

  • photos; 2 cameras; album; order you want

    We use 2 and sometimes 3 cameras for our holiday photos. After the installation, we do an album composed of pictures of all the cameras. When you view the album, photos are distributed between each photos of individual devices and require photos to s