G6 not powerup

Similar Questions

• 8570W: 8570W does not powerup on docking station.

  I have a 8570W with an A7e36AA docking station. I used to work perfectly.

  Recently, I don't know what changed, I can not power on the base and the notebook.

  When press the power switch on the docking station, it lights up, and between 2 and 8 seconds, the system is off again. All lights are off.

  If I powerup the 8570W when removed from the docking station it works well. When I put my notebook into sleep, put it in the docking station and it lights up, it all works.

  Anyone an idea what is causing the combination not to powerup decently?

  Replace the docking station. It was defective.

• TC 4200 not powerup

  Hello

  My tc 4200 lights.

  -battery: power led flashing: orange 8, 1 green and 1 yellow

  -on the AC adapter / CC: nothing.

  The battery is OK and the card too.

  What is the problem?

  Thank you

  B.

  That's all. From what you describe, colors you get does not have an answer at all. In general the codes only we go is the Caps lock flashing/cursor on the screen or anything on the keyboard. Power light don't give not any kind of sense usually. It would therefore be difficult to really give you an answer since the power light is flashing different colors.

  My laptop that works fine at home flashes different colors but has not any problems. So, I would call HP @8004746836.  They should be able to help replace the notebook or repair.

  THX

• HP Pavalion will not powerup, intermititantly.

  I have a HP Pavilion s7700n P/N RK576AA that I am convinced that needs a new power switch / button.  The system works perfectly, IF I can get it to power up.  Initially, I thought it was the power supply but when I took it to the shop the tech tinkered with it a little, and when he fired wide coverage without going through the CAP, it has the button market / stop and 'poof' it came on.  It worked normally for a short time but then the problem started again so I pulled the cover off the coast and the same results, I was able to get it to the top.  Long story short, the powers of power until now intermitantly unit button.  I am pleased to be able to get it started.  I guess what I'm looking for, is if anyone knows where I can get a new switch/power button (not the button cover/cap) or a part number.  Any help would be wonderful, waiting in anticipation!

  I have provided a link (s), but you will need to check/compare is for your switch.

  http://www.HPQ-parts.com/5042-8900?gclid=CNaEtNag6rkCFWho7AodZhgAcQ

  http://www.eBay.com/ITM/like/370882449084?lpid=82

• Added system ok but as far as I know, powerUp listener not pulling

  Hey. My application, in main(), adds a listening on starting system to cold (battery replaced), without error. However, the powerUp method below does not pull when I switch off my BB and sur-Appuyez the red end button for 5 sec and press once again (a warm start). How do you get powerUp to call? Code is below.

  MSL MySystemListener = new MySystemListener();
  MonthlySpend ms = new MonthlySpend();
  ms.addSystemListener (msl);

  private static class MySystemListener implements SystemListener
  {
  public void batteryStatusChange(int a) {}
  public void batteryGood() {}
  public void batteryLow() {}
  public void powerOff() {}
         
  public void powerUp() {}

  PerformAnyReset... schedule, calls so if not reset, don't program twice
  If (!.) PerformAnyResetWhichWasScheduledWhilePhoneWasSwitchedOff())
  ScheduleTotalResetForStartDateOfNextBillingCycle();
                                 
  SetIconAndTitle();
  ScheduleIconUpdateOvernight();
          
          
  String logMessage = "Warm" started
  If (EventLogger.logEvent (0x4c9d3452d87922f2L, logMessage.getBytes (), EventLogger.ALWAYS_LOG)) {}
  System.out.println ("Log successful!");
  }

  Hey - fixed. The application itself must be a SystemListener, not another class

  J

• Satellite Pro L300 will not start

  I have a portable Satellite Pro L300 and he won't start (in other words the power button and not going not past the first screen).

  Works for keyboard, but F2, F8 or F12 will not do anything, I can't here the disk hard powerup but it's like no one is at home. I don't know if it's the motherboard or the onboard battery. The computer is about 7-8 years

  Can anyone help.

  It s certainly nothing wrong with a RTC battery (as you said internal battery).
  The RTC battery can be charged. The unit must be turned on and adapter must be connected at least for about 18 hours.
  But I guess that this isn't a problem.

  The laptop does not start because of a hardware malfunction, but it's hard to say what role may be affected. But you should absolutely consult the RAM modules.
  This should be the first step, since the RAM modules are easy to replace.

  All other parts should be checked by the type of service.

• How do you LOCK your desktop in place icons so that they DO NOT moving whenever I RESTART or POWER-UP?

  How can I LOCK you your desktop in place icons so that they DO NOT moving whenever I REBOOT or POWERUP?

  I found some links that might help you.

  "How to change the alignment view desktop icons, and sort them by order in Vista"

  http://www.Vistax64.com/tutorials/126728-desktop-icons-view-sort.html

  http://www.howtogeek.com/HOWTO/Windows-Vista/save-and-restore-desktop-icon-layout-in-Windows-Vista/

• Dell Inspiron N5110 CPU fan does not work

  Hello world

  I have a problem with a DELL Inspiron N5110.

  When I turn on the laptop, the fan runs for 15 seconds then it turns off by itself... but the Windows starts correctly, and other components work fine.

  I know that I can't use my laptop if the CPU fan does not work because it will overheat the cpu and the motherboard so...

  Could you please give me an advice?

  Thank you

  The fan will run at powerup self test time, and then won't turn on (or run at full speed) up to a set temperature is reached.

  Function that replaces the motherboard, check that the thermal pads have been replaced when the radiator has been removed from the system.  If this part was not replaced, the system will run very hot.

• View dialog box on powerUp()

  Hello

  I am building an app that does not have a graphical user interface and runs in the background. The application uses PhoneListener to interrupt a call and create a new one in its place. Since I have no GUI I cannot send the keystrokes required to phone until after a dialog box is displayed (either a dialog box, asking permissions of the Application, or by changing the OptionsProvider). What I want to do, it's just pop up a dialog on startup so I can then inject my shots to end the call.

  Here is my code:

  public class GVIntercepter extends UiApplication implements SystemListener
  {
      public static void main(String[] args)
      {
          // register an options provider
          GVIntercepterOptionsProvider provider = new GVIntercepterOptionsProvider();
          OptionsManager.registerOptionsProvider(provider);
  
          // register a phone handler
          PhoneHandler phone_handler = new PhoneHandler();
          Phone.addPhoneListener(phone_handler);
  
          GVIntercepter instance = new GVIntercepter();
          // instance.enterEventDispatcher();
  
          if( ApplicationManager.getApplicationManager().inStartup() ) {
            // Add a system listener to detect when system is ready and available.
            instance.addSystemListener(instance);
          } else {
            // System is already ready and available so perform your start up work now.
            // Note that this work must be completed using invokeLater because the
            // application has not yet entered the event dispatcher.
            instance.doStartupWorkLater();
          }
          // Enter the event dispatcher.
          instance.enterEventDispatcher();
      }
  
      //Invoked when the user is putting the device into a power off state.
      public void powerOff()
      { }
  
      //Invoked when the device has left the power off state.
      public void powerUp()
      {
        Application.getApplication().removeSystemListener(this);
        doStartupWork();
      }
  
      //Invoked when the internal battery voltage falls below a critical level.
      public void batteryLow()
      { }
  
      //Invoked when the internal battery voltage has returned to normal.
      public void batteryGood()
      { }
  
      //Invoked when the internal battery state has changed.
      public void batteryStatusChange(int status)
      { }
  
      private void doStartupWork()
      {
        // Perform your start up activities here!
        Application.getApplication().invokeLater( new Runnable() {
          public void run() {
            Dialog.ask(Dialog.D_YES_NO, "Display?");
          }
        } );
      }
  
      private void doStartupWorkLater()
      {
        Application.getApplication().invokeLater( new Runnable() {
          public void run() {
            doStartupWork();
          }
        } );
      }
  
      public GVIntercepter()
      {    }
  }
  

  I tried almost everything to get the dialog box to display and I am at a loss here. Any ideas?

  Also, I'd be open to suggestions on power sending keystrokes to a background application in the phone app and use PhoneArguments to call without displaying any prompt at all.

  I never thought seriously about doing something like what you're trying to do, so I'm sorry this isn't a complete answer to your questions.  You may use these details to get a little further though.

  You say that your app is a bottom up, however you have extended UiApplication.  If your application is treated as it displays a screen of the user, but you never insert a screen, if your application never gets thrust in the foreground.  You will find that, once you started with your current code, your icon is available in the Task Switcher (ALT + ESC) and if you swap to your application, your dialog box is there to be seen (on a white background, as any UiApplication).  Try it and see.

  You can replace your code in doStartupWork() with something like the following, so that you can see actually started.  Try this and then see what happens when you select your application by using the Task Switcher after you answer your dialog box (note I use UiApplication rather than on request, simply because the code you call later should a UiApplication to run.  Your code works really because you have found your own application, which is currently spreading UiApplication.  If you change it to extend the Application instead, then you will get a UiApplication.

        UiApplication.getUiApplication().invokeLater( new Runnable() {
          public void run() {
              UiApplication.getUiApplication().requestForeground();
              Dialog.ask(Dialog.D_YES_NO, "Display?");
              UiApplication.getUiApplication().requestBackground();
          }
        } );
  

  I suspect that you really want to be a background application.  In this case, you extend Application rather than UiApplication.  Then, to bring something to the attention of the user, you can use UIEngine, as shown here:

  How - to alert a user to a background application
  Article number: DB-00407

  http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800332/800505/800608/...

  Alternatively, you can do what you do, stick your phone earpiece in place, then the UiApplication, the output is not in the Task Switcher.   Even if you have left your UiApplication, your hook is still in place and can still do something.

  I have a point more than related.

  You are actually setting up an earpiece of phone.  When this listener is controlled, it will run the app phone, not your Application.  This application has a GUI, then maybe you need not to use this dialog box "to access a graphical interface.

  Sorry, as stated, I never really looked seriously to do something like what you do, then I do not understand everything and maybe you have this covered.  Bit I hope this helps.

• Cannot open SCSI device ' devices/vmfs/genscsi / vmhba3:5:0:0 '(scsi3:0): the file is not found. Cannot configure scsi3.

  Cannot open SCSI device ' devices/vmfs/genscsi / vmhba3:5:0:0 '(scsi3:0): the file is not found. Cannot configure scsi3.

  I get this error when you add a new SCSI device to one of my Virtual Machines, the device is a tape drive HP SureStore DAT40. The error occurs when the virtual machine is running, around 60% powerup.

  I tried two types of SCSI cards, a "Adaptec 29160N" & a "Adaptec 29160LP" and two different cables, I get the same error with both. The ESX 3i 3.5.0 host to see two SCSI cards when checking under Configuration and then to storage adapters. When you click the SCSI card in the adapters of ESXi storage options, I see the tape drive listed as vmhba3:5:0 for the band and vmhba3:5:1 for the media changer. This makes me believe that, from the point of view compatibility, everything is good to go.

  When I change the instance of VM to add the tape drive, I select new SCSI device which passes next to select the SCSI device in the options, I see HP - HP and media - bands like peripheral parts possible. I tried a variety of virtual device nodes and they all produce the same error that has been pasted above. When ok is clicked it adds the new SCSI device and a new SCSI Controller 1 using the LSI Logic Controller, I also tried all the options under this menu, 'None', 'Virtual' 'Physical' and I have even changed the Type of controller BusLogic, same results even if I get the error posted above.

  The server in question is a Dell PowerEdge 2850, 2 x 3 GHz CPU, 8 GB of RAM, 300 + GB HD.

  I searched the net and these forums and did not find any post about the error posted above, I have some hair left on my head and I don't know what to do at this point. What is a compatibility issue? I tried to add the SCSI device on another virtual computer on the same ESXi host and it gives me the same error. I know the tape drive, scsi cards, and two scsi cables, I am using all work correctly.

  Any ideas?

  Hello vango333!

  Please try this.

  VMware Infrastructure Client

  1. 'Configuration'-> 'Storage'-> select target storage

  2. Please download * target VM *.vmx

  Edit the vmx file

  1. Edit *.vmx (wordpad, etc...)
     (Front)
     scsi0:1.present = 'true '.
     scsi0:1.DeviceType = "scsi-passthru.
     scsi0:1.filename = ' / vmfs/devices/genscsi / vmhba3:5:0:0. "
     scsi0:1.allowGuestConnectionControl = "false".
     (After)
     scsi0:1.present = 'true '.
     scsi0:1.DeviceType = "scsi-passthru.
                     scsi0:1.filename = ' / vmfs/devices/genscsi / vmhba3:5:0. 
     scsi0:1.allowGuestConnectionControl = "false".

  2. Download * *.vmx

  VMware Infrastructure Client

  ' Power On ' target VM

  It ends in the present.

  Good luck!!

• Apple Watch activity is not in the cloud?

  So, I've been using a Apple Watch for a while and my number one problem is that 'Activity', I put together for the last year is not sync with the iCloud, so when I upgraded my iPhone 6 to iOS10 all my activity watch is gone. I tested this point last week and it seems that "Activity" app does not synchronize your data in the cloud, so if you lose your phone or your watch you will have to start all over again and latest data are lost. This seems to be a huge concern when I spend all this time my overall follow-up and progress. Everyone see what happens if you put to level or restart/reset your watch or your phone?

  Hello

  Health and historical activity data is stored on your iPhone. It is not recorded separately in iCloud.

  To guard against data loss, be sure to make regular backups of your iPhone.

  If the backup via iTunes, make sure to select the option to encrypt iPhone backup (unencrypted backup excludes the sensitive data, including health and activity). iCloud backups are encrypted as standard.

  More information:

  The backup of your iPhone, iPad and iPod touch - Apple Support

• iTunes will not regroup under the name of artist albums

  I noticed at the bar on the left with the artists, sometimes there are twice, the same artist, with each having only some of the albums and I can't group all albums under the name of an artist to the bar.for some artists can't do, but I did it because some others.anyone know what to do?

  If you see unexpected songs groups when you browse an album - https://support.apple.com/HT204538 - 'songs from the same album may not be grouped as expected when you view them in display Albums in iTunes."

  For most people this solution seems to be one that works: August 2008 post by turingtest2 temporarily change labels - https://discussions.apple.com/message/7904806#7904806 or http://www.samsoft.org.uk/iTunes/merge.asp - add a letter at the end of the name of the artist, close the read information, then open it again and remove the letter. This works often but I had cases where securities combined when a letter has been added but divorced when he was kidnapped again.

  The following sections provide additional solutions:

  Often a solution: select all the tracks on the album, file > info (or right-click > news > Details) and give them all a single "album artist", or check the indicator of "compilation" (as in https://discussions.apple.com/message/17670085#17670085).

  Steve MacGuire alias turingtest2 - iTunes and iPod tips and tricks - grouping beaches in Albums - http://www.samsoft.org.uk/iTunes/grouping.asp (old post on Apple Discussions http://discussions.apple.com/message/9910895#9910895)

  If they are several CD sets, you will also need to enter the appropriate information in the fields of number of disk.  If they are not a set of multiple CDs that you must always make sure any vacuum or disc number fields are properly defined.

  Another explanation of hhgttg27 August 2015 - https://discussions.apple.com/message/27784417#27784417

  If they are mp3 files are trying to change the version of the ID3 tag, which can cause iTunes to re - write the tags and clarify inconsistencies.  I use iTunes 7.5 (Yes, from 2007) so I can't tell you where it is in later versions.

  I had a case of grouping stubborn reality.  The tracks will be re-group in a way that has no meaning when I changed metadata.  Without going into details, I deleted tracks iTunes completely, then add the files and they are all grouped together correctly.

• Why my notes sync between my Mac and iPhone?

  I have my MacBook Pro with Mac OS X 10.9.5 Mavericks and my iPhone is running iOS 10.0.1 and used to synchronize my notes! Is it because of the huge gap in operating systems? I SHOULD update my Mac to Mac OS 10.10 + for this problem? Thank you!

  In order to synchronize Notes between your Mac and iPhone, you must configure iCloud > http://www.apple.com/icloud/setup/

  But this requires macOS Sierra 10.12, the latest available version and the last iOS available for your iPhone.

• iPhone 7 more buttons outside does not

  I've had my iPhone 7 + for about 2 weeks now. Every once in awhile all buttons outside to stop, volume up/down, power, home. The home button will still record and push and give the sensation of taptic and touchID works. The phone itself still works and I can answer texts and which do not use notifications.

  The couple spent time he did, he came upon her in about 4-5 minutes, however it was about half an hour and still nothing. I want to restart my phone, but the switch does not work.

  Has anyone seen this issue or know how to fix?

  Thanks in advance.

  I just experienced the same problem on my iPhone 7, I think it's a bug in iOS, but I am using iOS 10.0.2. Power + button low Volume allowed me to turn it off then turn it back on... Apple please fix this bug!

• Why video does not work in safari

  The video on all Web sites IN safari has stopped working. No idea why?

  Do you get any error messages? If this is not the case, see if by double clicking the home button and drag to the top safari help. -AJ