Gap issue, fixed?

Similar Questions

• Rio's issue fixed

  Just a general question about gaps in my knowledge. We used a fixed point in the Rio, which is fine. If I do some basic math, say the multiplication of two numbers in the format 20,4 IE integer size 4 and 16 bits after the decimal point and then I get a number of 40.8. Should I re - convert this back to 20.4 or can I leave it and just continue. LabVIEW will make space for all the variable solutions or should I do it manually? I can see if I'm doing a lot of multiplies and adds the numbers get bigger and bigger.

  Also, I saw an article where the programmer made the move to the right and chipping itself but the fxp block for me? for example I multiply two 8.4 numbers and get a 16.8 who do I shift to the right and re-scale. What is recommended for the addition, division, and multiplication.

  Thank you

  I don't know what you're asking here.  What do you mean by, "LabVIEW Will make way for all the different solutions?"  By providing the result as a value of 40.8, LabVIEW is to ensure that there is enough space for any results.  You can continue with this value, but afterwards, you should it retract.  With number requires more bits more FPGA resources, and there is a maximum number of bits that can be used to store a value.  It is up to you to know how you want to handle this scaling.  Sometimes, it is more important to preserve the most significant bits and lose resolution.  In other cases, you can know in advance the normal range of entries and can accept the overflow for unusual entries in order to maintain the resolution for typical values.  There is no specific best practice.  See warnings and recommendations for the use of fixed point numbers and.

• EVGA Nvidia Geforce 8400 GS issues: [FIXED] screen and the sound does not [FIXED] virgins

  I have a HP Compaq dc5750 I just got an EVGA Nvidia Geforce 8400 GS, and I'm having a problem with it. I disassembled the computer cover and installed, replace the cover, turned on the computer and the monitor not power not on. So I decided that I had to disable the integrated graphics card (ATI Radeon Xpress 1150), then I added the card even once. Still happens... Monitor powers on without the new graphics card. My monitor is 8 years old and lacks a DVI port. I have to connect the monitor to the graphics card to make it work? I want just this card to work.

  UPDATE: white screen problem is fixed, but the sound does not (no audio installed device) even if the audio driver is installed

  Hello

  This kind of question is mainly caused by the sound card driver is not not compatible.  Contact the hardware manufacturer directly to confirm the driver is compatible or not.

  Test the issue with another pair of speakers or headphones, or you can plug the device of reading to another port to see the result.

  In the meantime, you can also see if the playback device is disabled. To do this, please check the following steps:

  1 Please, click Start-> Control Panel-> Sound.

  2. on the playback tab, right-click on the empty square and then click on "show disabled devices".

  3. check if your playback device is disabled. If so, right-click on it and click Activate.

  1. Please click Start, type services.msc and press ENTER.

  2. double-click on Windows Audio.

  3. click on the 'general' tab. Make sure the "Startup Type" is "automatic". Then please click on "Stop" under "Status of Service" to stop the service.

  4. click on "Start" under "Status of Service" to start the service.

  Reinstall the audio device

  1. click on start, type Device Manager, click on Device Manager to open it.

  2. expand ' audio, video and game controllers ".

  3. right click on your audio device, and then click on uninstall.

  4. check "delete the driver for this device".

  5. click on OK.

  6. after that, restart the computer, the device and the driver must be reinstalled automatically.

  Please check if the problem can be solved now.

  If the problem persists, please install the latest driver of sound card on the manufacturer.

  I found the problem... once again: I had to go to the BIOS and enable Audio integrated. My audio integrated uses Realtek High Definition Audio instead of Nvidia High Definition Audio.

• Alienware 17 R3 - BSOD ISSUE/FIX - killer E2400 Ethernet Driver / Version: 1.1.56.1236_A01

  This question/correction is in what regards the Alienware 17 R3 model. It has not been tested and confirmed for other models! ***

  The following information is presented to assist you (and DELL) with a DRIVER from DELL problem that causes WINDOWS 10 fixing to the accident of BSOD & MAKE YOUR SYSTEM unable to boot in windows desktop!

  I have listed the factors that are causing the problem and then follow up with what (I have laboriously have troubleshooted for over a week now) pilots are currently working without problem. I hope that this helps you turn it back on, and if you have a message of the moment and let me know! ((DELL-S'IL VOUS PLAÎT PASSER CE LONG À N'IMPORTE QUEL DÉPARTEMENT DE PRESSE NOUVEAUX PILOTES!)) PLEASE PATCH/FIX!))

  Device Manager > network adapters

  Bluetooth (personal area network) device / driver Version: 10.0.10586.0 (21/06/2006)
  (Heading RFCOMM Protocol TDI) Bluetooth device / driver Version: 10.0.10586.0 (21/06/2006)
  Killer e2400 Gigabit Ethernet Controller / Driver Version: 9.0.0.5 (27/04/2015)
  Killer Wireless-n | a | AC 1535 Wireless Network Adapter / Driver Version: 12.0.0.137 (23/08/2015)
  ***************************************************************************

  Control Panel > program and features

  Suite of killer Network Manager / driver Version: 1.1.54.1220
  Killer wireless drivers / Driver Version: 1.1.56.1236
  Qualcomm Atheros Bluetooth 61 x 4 Suite (64) / driver Version: 12.0.0.102
  ***************************************************************************

  Latest drivers available from dell.com (Alienware 17 R3)

  Killer Wireless-AC pilot 1535 / Version: 1.1.56.1236_A01
  ((Nom de fichier/.exe: Network_Driver_2WDXK_WN64_1.1.56.1236_A01))

  Killer E2400 Ethernet Driver / Version: 1.1.56.1236_A01
  ((Nom de fichier/.exe: Network_Driver_C95MK_WN64_1.1.56.1236_A01))

  Driver Bluetooth Killer Wireless-TA 1535 / Version: 10.0.0.102_A00
  ((Nom de fichier/.exe: Communications_Driver_PJ4XH_WN64_10.0.0.102_A00))
  ***************************************************************************

  When you try to install the Killer Ethernet Driver E2400 / Version: 1.1.56.1236_A01, the following problems occur:

  -ATTENTION ERROR/InstallShield DLL custom Action
  [Exclamation point in a yellow triangle] "Cannot find the entry point of the function"TweakLOMPerformance", make sure that it is implemented. .

  -L'installation will not continue or complete until you click a button 'OK' for the above warning ERROR

  -Once you click on 'OK', the installation will be complete and inform you that your system needs to reboot. At this point, 1 of 2 things will happen
  -1. The system will be blue crash screen immediately when the complete installation
  -2. The system will be blue crash screen after reboot, at the stage of account log-in/enter windows password

  -There are three possibilities BSOD:
  1 BAD_POOL_HEADER (most common result)
  2 KERNEL_SECURITY_CHECK_FAILURE
  3 IRQL_NOT_LESS_OR_EQUAL

  -Once the BSOD occurs, you will not be able to boot in Windows 10. The system will crash, restart, crash, reboot, and then win 10 implements its program of recovery/repair of the system. If you have a system restore, then you can reverse this pilot plant successfully, which will allow you once more in Win 10 w / no another BSOD. If you do NOT restore the system save point, your options become more extreme: 1. restore/Reset before installing the affected driver listed above; 2 restore/reset; 3 NOTE: Starting Windows hotfix fails to solve the problem

  Variables

  On an another Alienware 17 R3 (exactly the same card/construction material), installation and the following drivers work correctly without BSOD:

  Device Manager > network adapters

  Bluetooth (personal area network) device / driver Version: 10.0.10586.0 (21/06/2006)
  (Heading RFCOMM Protocol TDI) Bluetooth device / driver Version: 10.0.10586.0 (21/06/2006)
  Killer e2400 Gigabit Ethernet Controller / Driver Version: 9.0.0.8 (28/07/2015))! ANOTHER DRIVER VERSION VS. Above!
  Killer Wireless-n | a | AC 1535 Wireless Network Adapter / Driver Version: 4.0.1.137 (03/09/2015). ANOTHER DRIVER VERSION VS. Above!
  ***************************************************************************

  Control Panel > program and features

  Suite of killer Network Manager / driver Version: 1.1.56.1236! NEW VERSION of DRIVER!
  !!! NOT INSTALLED/NOW! (Tueur sans fil pilotes/Driver Version: 1.1.56.1236))
  Qualcomm Atheros Bluetooth 61 x 4 Suite (64) / driver Version: 12.0.0.102
  ***************************************************************************

  TCOLE334:
  Thanks for the solid recommendation; your post on the removal of the Dell printer provided Killer drivers (wireless network and ethernet), and then update directly from the site of the murderer himself worked like a charm.

  So, for anyone who has an Alienware 17 R3, or face a similar problem with BSOD by Killer drivers, I can confirm the work of solution of this TCOLE334 and fixed my issues surrounding network causing BSOD drivers.

  Now if only we can get our BSOD problems resolved with the Dell SupportAssist program. Starting from 04/03/2016, I'm waiting on an update of PC Doctor directly (I have been in contact with them for the last month now and work with them to try to resolve this breaker program.) I emailed plant minidumps, memory.dmp, newspapers, etc. We'll see. Patience is a virtue!)

• Issue fixed

  I have a simple test program that is a digital FIR filter. I'm simulate for Rio indeed, as I have similar problems there.

  as it is, the program in the picture below actually works well. Should null to a sample rate of 1/4 what it does. However, if I replace the table of fixed point zeros

  with am initialize the function array (see the diagram below), and then it breaks down. The reason I want the matrix of initialization, is that it could be quite a large table - say 400 values inside and I don't want a load of hugh of fixed point zeros there. I changed the format of the initialization of zero to fixed point, but it still does not work.

  Thank you

  FXP values in the table are of different type of FXP (32-bit, 16-bit length of whole word) than where initialize you the array (1.bit length), so the results will certainly vary. You must ensure that the constant is of the desired type.

  The constant you use to initialize the shift register is also 1 bit, probably not enough.

  Why do you not use autoindexing on the coefficient table?

• Windows 7 Advanced issue fix

  I recently installed a fix to save the changes in time for FIJI on a laptop Windows 7 daylight. The patch installed fine and I could see that summer time has been captured on the system clock. However, when I put the exact time (which is summer time) the system clock is automatically 15 minutes. The advance of the checkbox is checked. The time is set. But after a few minutes, the time goes back about 15 minutes.

  Transfer your question here, please: http://social.answers.microsoft.com/Forums/en-US/w7performance/threads ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Atheros wlan issues - fixed - Solution

  My L40 is now now works as it should of 1 day (October 07) this has been since I loaded the latest atheros driver see 7.6.0.70 gave me via the toshiba site and installation of vista service pack 1. Like two things. has occurred the same day that I don't know if the problem was one or the other or both.
  I now get free wifi, as soon as I start and the connection speed is 6 MB as difference to the 1 mb before that.

  Thanks for sharing this info with us.
  It s useful to other users in our little community here ;)

  Good bye

• Activation of data roaming connection issues fixes?

  Had the terrible problems of data connectivity. I take the train from Baltimore to DC daily and w / my OG Droid, never had any problems, although the location of one or two only seemed to have 1 x available. With my Bionic, but often I drop my connection of data completely (more it seems when I bought the phone in September - not 100% sure because I was not pay special attention to this those first couple weeks).

  For the heck of it, I thought that I have reported on twitter and see what kind of response I would get @VZWSupport. (I get still better support of their people from twitter that Comcast in my local office).

  Got a reply (see chart).

  They told me to turn on data roaming. Really? Anyone had success with this? I'm worried of running a huge bill.

  I must say that I have questions and whe I turn airplane mode, I noticed the very briefly - circuit symbol for a second or two at most, without worrying about if I find myself with a data connection.

  A response to my concern over roaming charges:

  "As long as you travel abroad, you are ok. New s/o is on the way to improve the data connections. »

  New s/w is on the way? everything what could be?

• HP Pavilion 15 t issues with Internet connectivity can be used under Windows 8

  So I just got my new HP Pavilion 15 t-e000 CTO Notebook PC last week, it runs Windows 8 & amp; It is a 64-bit.
  
  The only problem I've had is to stay connected to my wireless Internet. The connection stops at random intervals saying 'Limited' instead of 'connected '. I have to constantly disconnect and connect to my WiFi. It's particularly frustrating when I am trying to download something that lasts longer than a few minutes because the Internet connection cuts, and I have to start the process.
  
  I tried pretty much every "difficulty" people have posted that worked for some people. No luck for me. Sometimes it seems that he will stay connected and then I try to connect to a web page or download something and it turns off again.
  
  -Turn off the "Allow computer to turn off this device to save power" under power management in the properties of my wireless connection section... DID NOT WORK
  
  -By using the command prompt to reset the network card... DID NOT WORK
  
  -Running the network and Internet, and convenience stores something... Didn't WORK * update: if I run the connection test network via the HP help/support on my desk Center, while the connection says Limited, I get the notice that the 'default gateway was not available"and the router has been handed over to zero and issue fixed, etc. BUT if I run the test, while the connected said wireless, the test still says there is no problem. And although the test 'fixed' the issue, it does not because the Internet always cut again.
  
  -Updates Windows has installed new updates several times... DID NOT WORK
  
  -Forget the wireless network and set up as a new... DID NOT WORK
  
  -With the help of my computer right next to my wireless router... DID NOT WORK
  
  Used wireless router is: Cisco Linksys Wireless-G 2.4 GHz router to wide band as well as our network is WPA with a security code. We also have an Internet DSL SpeedStream thing (sorry, I don't know what it's called). The Compatibility Center said that this router is compatible with Windows 8. Other computers running Windows 7 and Windows Vista, iPhones, iPads and all work fine.
  
  My laptop uses Intel Centrino Wireless - N 2230 and the light is on and it still says ' device working properly "in the properties.
  
  For any help or suggestion would be greatly appreciated because I am at my wits end.
  
  Thank you

  Therefore, it seems that my problem with the limited Internet connection has been resolved. I didn't use my computer for two days and this afternoon, when I turned it on I was still having problems. However, I went to the HP Support Assistant, and it appeared that I had a few updates to download and install, so I let him do his thing. It took awhile because the Internet kept cutting out, but once the update for the wireless Intel have finally set, my connection is REMAINING CONNECTED. Finally!

  I don't know why when I went into the properties wireless it says "device working properly ' and when I tried to update the driver it says"your driver is the latest version"or something else.

  I suggest you just go to the HP Support Assistant and updates in the section "Updates and the updates of". It was a bit random, but touch wood my looks of problem connecting wireless to be gone.

  Hope this helps

  P. S.

  Here is a screenshot of what the HP Support Assistant (this is the logo of big question mark) main screen looks like:

  

• fix Windows 7 incompatible for the conquerors Age of Empires

  Hi, my operating system is windows 7 and IE 8 browser. When I installed Win 7 disk, he said first of all uninstall salary of Empires, and then re-install after. I am running 32-bit and my resolution is 1600 x 900 (recommended). All works, but rather of Age of Empires. I play the Conquerors Expansion, but the resolution of the grass and the background is really rough. I tried to change the resolution of my desktop to 256 and it ended all jerky looking just like the game so I changed it back. Microsoft has a patch for this game file? Where would I look?

  Hello
  I also had this problem and concluded that the only solution is to exit explorer.exe when using AOE II The Conquerors on 7.
  I've done I have simple "patch" to do this automatically please read more on my site (http://www.furgelnod.com/software/programmes/age-of-empires-ii-display-issue-fix/). I hope that the information there can help in your situation.

• How can I fix error "changed default location for Windows Update files" that Fit-It notes several times, but does not solve?

  Using Windows XP Home Edition SP3, IE8, and Firefox 13.

  Used several times to install and MS Fit-It tool to try to fix Windows Update so that will download the updates of high priority.  4 four security updates not always settle.  Fix - It tool shows that "one or more Windows Update are configured incorrectly" and that it has been fixed (run 10 times).  He also pointed out "where Windows Update stores data has changed and needs to be repaired", but offers no solutions to fix this problem.  Cannot find any reference to this in the KB or MS answers.

  Is it possible to repair this problem and it will make a difference by allowing for installing security updates?  I talked to Ms. telephone and e-mail do not install security updates, but they say I have to pay $99 to get this issue fixed MS Update.  I thought I read that security patches are supposed to be supported without charge.

  Any new advice or techniques for solving this would be appreciated.

  Hello RickH999,

  Follow the steps in the article to reset the Windows update components and check if the problem persists.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  I hope this helps.

• 2 gap PX in IE

  I've looked everywhere to try to resolve this problem in Internet Explorer

  Just below the main navigation home join, great members, I have a gap of 2px instead of him sitting on the scrolling banner flower.

  This seems only in Internet Explorer

  http://www.australiancheapholidays.com/site/

  Thank you

  Hello

  I just upgraded to IE 9 and do not see the gap 2px and I have also considered this in Adobe browser Lab and then IE 7, IE 8, IE 9 shows a 2px gap.

  The problem of 2px gap was "fixed" in IE9 using the html5 doctype, but in most versions, he indicated that the browser is in quirks mode, (even a validated page can be in quirks mode in IE). IE quirks mode can be 'made' by some IE browsers, but not in others of the same page, the same version number may or may not enter mode quirks for the same page.

  There was a discussion about this on the blog of developers of IE 6-8 months ago.

  To see how IE "Decides" to use quirks mode see - http://blogs.msdn.com/b/ie/archive/2010/03/02/how-ie8-determines-document-mode.aspx.

  PZ

• Oracle Dataguard - newspapers apply question

  Hello
  Due to a problem our archives logs does not production, the day before. We had our intelligence in London. I don't see any error messages. do not know what is going on, I had open case with oracle support.
  We must stop all our production and DR last Sunday. Once it is up he stopped log shipping. our production server is a node 3 CARS.
  
  I just need how to apply logs archiving of standby production, which is based in London.
  
  appricate your quick response.
  
  Thank you

  To restore a database on hold:
  1 manually copy all log files miissing Archives from the primary to the standby server

  2.) cancel managed recovery on the standby database:

  change databae recover managed standby database cancel;
  3.) recover automatically:

  automatic recovery of the standy basis;
  4.) switch managed standby

  recover managed standby database disconnect;

  OR...

  Manually set a gap:
  =============================

  In some rare cases, it may be necessary manually fix the gaps. The following section describes how to query the appropriate views to determine whether there is a gap.

  On your physical standby database:
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Query view ARCHIVE_GAP of V$:

  SQL > SELECT * FROM V$ ARCHIVE_GAP;

  THREAD # LOW_SEQUENCE # HIGH_SEQUENCE #.
  ----------- ------------- --------------
  1 333 336

  The query results show that your physical database ensure is currently absent sequence logs 333 in sequence 336 for thread 1. After identifying the gap, issue the following SQL statement on the database primary to locate the archived redo logs on your primary database:

  SQL > SELECT NAME FROM V$ ARCHIVED_LOG WHERE THREAD #= 1 AND DEST_ID = 1 AND
  2 > SEQUENCE # BETWEEN 333 AND 336;

  NAME
  --------------------------------------------------------------------------------
  /U01/oradata/arch/arch_1_333.arc
  /U01/oradata/arch/arch_1_334.arc
  /U01/oradata/arch/arch_1_335.arc

  Copy the logs returned by the query for your physical database Eve and register by using the ALTER DATABASE REGISTER LOGFILE command.

  SQL > ALTER DATABASE REGISTER LOGFILE
  ' / u01/oradata/stby/arch/arch_1_333.arc';
  SQL > ALTER DATABASE REGISTER LOGFILE
  ' / u01/oradata/stby/arch/arch_1_334.arc';
  SQL > ALTER DATABASE REGISTER LOGFILE
  ' / u01/oradata/stby/arch/arch_1_335.arc';

  Once the files newspapers were registered in the standby controlfile, you can restart the MRP process and the standby database 'catch up' the gaps in newspapers or you can manually restore the standby database.

• I want to go back to Firefox than Firefox 32 31. How can I do this?

  I found that Firefox 32 is not compatible with the theme of Windows 7 desktop that I currently use (high contrast white theme). I tabled this question like a bug on Bugzilla site, but until they get this issue fixed, I want to go back to Firefox 31.

  My questions are:
  1. what I have to uninstall Firefox 32 first, or can I just install Firefox 31 on 32 of Firefox?
  2. get lost (or ruining) my settings of Firefox by doing this?
  3. where can I get Firefox 31?
  4. is there a way I can stop the automatic updates of Firefox does not happen and instead get a prompt?

  Thanks for any information, that anyone can give on this subject.

  Because the latest versions of Firefox contain the latest security patches, old versions of Firefox may have security or functionality problems. For this reason, we do not recommend downgrade your version of Firefox.

  If you want despite any downgrade Firefox, you can download any version of Firefox from here.

  Can I ask you why you're decommissioning?

  Now, the answers to your questions:

  1. You should be able to simply install Firefox 31.0 and should replace version 32.0.
  2. Your settings should stay the same, however, I would recommend your application data backup in case something goes wrong.
  3. See above
  4. This setting can be changed partners to automatic updates can be found under the tab 'Advanced' from the Options window

• After you download the update of firefox 10 I can remove is no longer mails in gmail, this isn't a problem of google

  I have already filled in 3 forms for this more how do need it all the information I can be found

  Please do not forget to mark your question as solved, assistance if the issue/fix has been identified.

  Disable all Add-on/Plugins, then enabling 1 by 1 is the only operation I know of troubleshooting will restrict the Add-it/Plugin troubled.

  Perhaps if you provide a list of some add-ons you have installed I know whatever it might be. Usually problems like those experienced come you from toolbars or addons installed by your AntiVirus