Gather the router E2500 and Voip DMZ box
I had an old belkin router which is dead. I have port forwarding and DMZ through my box Voip IP 192.198.0.1XX (immutable de.0.1) my new router IP is 192.168.1.1 now (DMZ immutable a.0.1) and I'm not sure how to get all DMZ d together and without flow. Any help would be greatly appreciated, I searched and found nothing on this issue. Thank you
Hey, mustache! Have you tried to specify the device in the DMZ by MAC address instead of the IP address? To do this, click here. Update us how it goes!
Kind regards
Ethel_10700
Linksys technical support
Tags: Linksys Routers
Similar Questions
-
Failed to get the connection between the router WRT54GS and roku
Hello
I am new to this. How can I get my router to connect to roku.
When I enter my password router Roku he can't find the router. And when I use Cisco Network Magic, it does not find the Roku device.
Thank you... I didn't was not completely able to get in... but I found that my personal wpa password was different from what I used... and then I've always had trouble getting in... but this has certainly helped.
I entered the MAC address and then I was in!
I am so grateful to all who have contributed and are looking for me and we all in this forum
-
New Internet Service, do I need to reset the router E2500?
I had used temporarily my router E2500 to work with a wireless broadband source by connecting it to a Cradlepoint CTR500.
Now I will connect the E2500 to run (and ongoing) with Time Warner Roadrunner using a modem cable Scientific Atlanta WebSTAR DCP 2100. Given that I'm changing the source of the internet, do I need to reset the E2500 to factury default values, and then perform a new installation using the Cisco Connect software?
The cable modem is currenlty connected via an ethernet straight cable to the PC. I had read that remove the ethernet connection and the cable from the cable modem and the modem powered off for 10 minutes will cause the modem to "forget" the PC's MAC address. Once connect it MAC address of the PC had been "forgotten", the ethernet cable from the modem to the router, which make the modem pick up the router's MAC address and eliminate the need to clone the MAC address of the PC. Does this sound correct?
Unplug the power to the modem cable for 30 seconds should be good enough. In regards to the router, you should be able to get without a reset, if it is set to DHCP for the type of internet connection.
-
Using the touchpad. charms and a small box at the bottom left pop up
I have a laptop HP Envy m6-1125dx. Sometimes when I use the touchpad the charms and a small box that shows date and popup all battery indicator. I have a feeling that part of my hand is in contact with the merits of the case. What should I do to stop these 2 boxes to appear?
Hello
Try the following.
Open windows control panel, open the mouse, select the settings of the Clickpad tab and then click the button settings Clickpad - option, you must disable is called "edge punches" ( Remove the check mark and click on apply to save the change)-your exact hardware/software may be slightly different, but see the picture below.
Kind regards
DP - K
-
the wifi does not work on my iPhone when I'm away from the router in my room, but it's not too far, it's like a couple of inches away from the living room and it does not work for some reason...
First restart the router - remove all power for 15 to 30 seconds.
If that is fixed not try to change channels on the router using the router configuration panel.
On the phone go to settings/general/reset - Reset network settings if any of the above doesn't help. It will be reentering your WiFi password.
-
The router 851 and 871 VPN issues still
Main site
1 - all connectivity-all thin - Web - database-email Mail - Proxy - ETC.
2 - VPN Tunnel to the TOP
Remote sites
1 - VPN Tunnel to the TOP and tests
1 cannot ping the main location of the 192.168.0.X (Yes any IP address)
2 - could not get out to the Internet (GO HOLLOW PROXY SERVER 192.168.0.3 even if I could ping)
3 could connect to the database but crashes right after the login screen. Can ping the address of 192.168.0.11 to this fine location database but the connection hangs and does not
* HAND CONFIG
crypto ISAKMP policy 1
BA 3des
md5 hash
preshared authentication
Group 2
!
crypto ISAKMP policy 3
BA 3des
md5 hash
preshared authentication
Group 2
XXX address X.X.X.X isakmp encryption key
XXX address X.X.X.X isakmp encryption key
ISAKMP crypto keepalive 5 20
!
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
!
bssn 10 ipsec-isakmp crypto map
Description VPN for PARK
defined peer X.X.X.X
Set transform-set RIGHT
match address 100
bssn 20 ipsec-isakmp crypto map
VPN for Corneilia description
defined peer X.X.X.X
Set transform-set RIGHT
match address 102
bssn 30 ipsec-isakmp crypto map
Description VPN to OAK
defined peer X.X.X.X
Set transform-set RIGHT
match address 103
bssn 40 ipsec-isakmp crypto map
Description VPN to Herbert George Wells
defined peer X.X.X.X
Set transform-set RIGHT
match address 104
interface FastEthernet4
WAN
IP address 216.x.x.x 255.255.255.128 secondary
IP 216.x.x.x 255.255.255.128.
no ip redirection
no ip unreachable
no ip proxy-arp
NAT outside IP
IP virtual-reassembly
route IP cache flow
automatic duplex
automatic speed
card crypto bssn
!
interface Vlan1
Entry door
IP 216.X.X.X 255.255.255.248 secondary
IP 192.168.0.11 255.255.255.0
no ip redirection
no ip unreachable
IP nat inside
IP virtual-reassembly
route IP cache flow
IP tcp adjust-mss 1452
!
IP classless
IP route 0.0.0.0 0.0.0.0 216.x.x.x.
!
IP nat inside source overload map route interface FastEthernet4 sheep
!
recording of debug trap
access-list 100 permit ip 192.168.0.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 101 deny ip 192.168.0.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 101 deny ip 192.168.0.0 0.0.0.255 192.168.6.0 0.0.0.255
access-list 101 deny ip 192.168.0.0 0.0.0.255 192.168.7.0 0.0.0.255
access-list 101 deny ip 192.168.0.0 0.0.0.255 192.168.5.0 0.0.0.255
access-list 101 permit ip 192.168.0.0 0.0.0.255 any
access-list 102 permit ip 192.168.0.0 0.0.0.255 192.168.6.0 0.0.0.255
access-list 103 allow ip 192.168.0.0 0.0.0.255 192.168.7.0 0.0.0.255
access-list 104. allow ip 192.168.0.0 0.0.0.255 192.168.5.0 0.0.0.255
not run cdp
sheep allowed 10 route map
corresponds to the IP 101
* REMOTE SITE
crypto ISAKMP policy 1
BA 3des
md5 hash
preshared authentication
Group 2
XXX address X.X.X.X isakmp encryption key
ISAKMP crypto keepalive 5 20
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
!
bssn 10 ipsec-isakmp crypto map
Connect to main BSSN description
defined peer X.X.X.X
Set transform-set RIGHT
match address 100
interface FastEthernet4
IP 216.X.X.X 255.255.255.224
NAT outside IP
IP virtual-reassembly
automatic duplex
automatic speed
card crypto bssn
!
interface Vlan1
Entry door
IP 192.168.1.2 255.255.255.0
IP directed broadcast to the
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1452
!
IP classless
IP route 0.0.0.0 0.0.0.0 X.X.X.X
IP http server
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
IP nat inside source overload map route interface FastEthernet4 sheep
!
access-list 100 permit ip 192.168.1.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 101 deny ip 192.168.1.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 101 permit ip 192.168.1.0 0.0.0.255 any
not run cdp
sheep allowed 10 route map
corresponds to the IP 101
Thank you
Laughing out loud
On the remote router access list 100 should look like:
access-list 100 permit ip 192.168.1.0 0.0.0.255 any
On the main router, the 100 access list should look like:
access-list 100 permit ip any 192.168.1.0 0.0.0.255
HTH,
Kind regards
Kamal
-
Lack of cRIO 9154 in the add targets and devices dialog box
Hello again all you lovers forum useful!
I have an existing LabVIEW project which includes a Hypervisor PXI real-time target. One of the devices that target is a chassis cRIO 9114. I now need to add a cRIO chassis additional 9154 so according to a conditional disable signal, I can modify my code to talk to the old chassis or the new chassis, which keeps my modular code across different hardware.
However, I write my code update on my regular computer which is not hooked to the target, so when I right click on the target of the hypervisor in my project and select new-> "targets and devices...". ", I can not select the" existing target or device "to be detected automatically. Instead, I click on the 'new target or device' to add just anyway, and I expand the CompactRIO there, and... no 9154. I have a bunch of other cRIO features (see screenshot), including the 9114, but no 9154.
I guessed that maybe my LabVIEW installation (2012 SP1) know not this chassis when it was released last year, so I tried to install the latest drivers from device with discs on developer LabVIEW 2013 that I just got, but he hung up during installation (the first time at 0% the second time at 27%, listed as "Validating install" for long, long before I was abandoned and cancelled). I restarted my computer, but no change to this problem.
Does anyone have any ideas as to why I can't choose a newer chassis to insert in my project without that it is actually attached to my computer? And I was too quick to renounce installation of the driver, not that I don't know if that would have solved the problem anyway? : PEI
Thanks for your help, as always,.
-Joe
Hello Joe,
The 9154 NOR is a RIO MXI-Express chassis that's why it should appear under the section of chassis MXIe-RIO.
For installation if you are concerned that it has not installed correctly, you can try run a repair on the NOR-RIO software and look at MAX to see if you have RIO 12.1 or 13.0.
-
Since I installed the latest update of Firefox, reduce it, restore, and close are missing visually, even if their functions are always present.
I also started to have one of these dialog boxes asking whether or not I'd like to allow a program to make changes to my PC when I open Firefox.
I could fix this apparently either by way of turn disable the compatibility mode setting, or by rebooting completely.
Then, Firefox logo disappeared from the icon for a while, being replaced by the default Windows system image which is displayed under the icon of unspecified files.
I do not know whether or not the uninstalling and reinstalling Flash Player and restart had something to do with this corrected, but at some point, she is back to normal.
-
When I put the virtual memory in windows vista Home premium is ok! to enter the boxes the same size (MB) "initial size and the Maximum size" example 2877 (MB's) entered in each box for initial and maximum size?
Yes, you can do it. The minimum must be large enough to contain an image of the core. If the maximum is too small, you will get the unpleasant results.
This article has some tips on the size of the page file at the end.
http://blogs.technet.com/b/markrussinovich/archive/2008/11/17/3155406.aspx
-
Tunnel GRE / IP Sec VPN firewall between the router Cisco and Fortigate
Hello
Can I do GRE Tunnel / VPN IP Sec between Cisco router and Fortigate Firewall?
Thank you
Hi zine,.
As long as the Fortigate device support GRE over IPSEC, you will be able to create the tunnel between these 2 devices.
Here is the config for the Cisco Site:
https://supportforums.Cisco.com/document/16066/how-configure-GRE-over-IPSec-tunnel-routers
Happy holidays!
-Randy-
-
Re: update Adobe Elements and drive
I unchecked the box that allows the installation of Google Chrome and Google toolbar as well as the update. Just as I clicked 'install', I noticed that the box of Google Chrome has been verified again. I haven't checked the Google Chrome box. How can I prevent the installation of Google Chrome when I authorize the installation of the update? (assuming that some of all of Google Chrome was downloaded before I closed the browser?)
Use the http://get.adobe.com/reader/enterprise/ offline installation program - it is not supplied with any software 3 rd-party.
-
DeskJet 3520: Simultaneous connection to the router wifi and DJ3520.
How can I set up the printer so that I don't have to unplug my befor internet connection I can print.
Well the best place for that information is the User Guide that you got with the printer or download from the page of full HP support here.
Whatever you are looking for is here. Page 35 of the user's Guide says it all.
-
Computer does not recognize 3050 HP printer ip if the router, computer and the printer off
Hi there @Bbandb , I hope you are well!
It seems that the printer is disconnected from the network when it is switched off. I would say that you are trying to assign a static IP address to the printer to help stabilize the connection. I hope that will prevent network disconnections!
Click here for help on the allocation of static IP address: printer does not maintain the wireless connection
I hope that helps
-
Which router is the most stable and the most suitable?
Hello
I have a Linksys Switch (Gigabit) connected to various materials in my small business via CAT7. Everything turns end network; wait in line ISDN BRI, which currently gives me only 12 Mbps download. I also connect the router to a VOIP to ISDN gateway which i sconnected to my internal PBX which I assume provides a load on the router.
Unfortunately my RVS4000 (firmware v1.3.2.0) simply keeps now hung and I spent a lot of time trying to understand why and I'm close to simply replace the router (as the loss of time is less than the cost of a new device).
Please can someone advise a suitable router with a firewall, which is VERY stable (+ 99.9% time)? I want to stay in the world of cisco/linksys here I first looks for a solution.
Thanks a lot for your suggestions of experts. If someone is overjoyed with their router then please let me know.
BTW - I have no Wifi as the router is in a small data center with Wifi does simply not apart of as the walls are 60cm thick. A wired router is sufficient.
Best regards
Mark
I would go for 890 series router has just begun.
-
I can't print from my 2nd computer. I use Verizon Fios to communicate with a wireless router (Belkin) (main? / main thru?). I have 2 computers that access my internet connection. The 1st computer that is in the same room as the router "verizon" and the printer is capable of printing. The 2nd Bureau is not. But there is good communication with the internet.
Would it in my settings that could very well be the problem?
Hello
1. what operating system is installed on your second computer?
2. has been the second computer can print very well without any problems in the past? If Yes, you did any hardware or software changes before the show?
3. that you get an error message when you attempt to print from the second computer?
4. What is the brand and model of the computer and the printer?Please provide us with more information about the issue so that we can help you better. Visit the link below and send your request.
Suggestions for a question on the help forums:
http://support.Microsoft.com/kb/555375In the meantime, you can refer to the links below.
Troubleshoot network printer in Windows Vista and Windows 7:
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problemsResources for the resolution of the problems of printer in Windows XP:
http://support.Microsoft.com/kb/308028Kapil Purohit - Microsoft
Maybe you are looking for
-
Zoom in and out of the Web site Windows no dependencies a mouse - windows 7 pc
I do not use a mouse on my laptop. Each time the window zoom in or out because that weighs a finger on the touchpad. How do I Zoom in and out in order to control the size of the window?
-
How can I clear the history of firefox url 10.0
I just want to keep clear of the previous url url.
-
The alarm volume is at the highest level, but can it here. Help!
-
How to change the sequence of the BIOS?
Hello... I made a bootable CD... using Seagate Disc Wizard... latest version... my computer does not start from the CD/DVD drive via the USB port of a Seagate 1 TB HDrive. I have a new HP Pavilion Slimline desktop PC... 400 224 How can we change the
-
BlackBerry Smartphones how Mobipocket easier to access
I'm not an experienced BB user so please bear with my lack of knowledge. We're going to the OS and I want to be able to use the BB as a book reader. I managed to install Mobipocket on it. It is a very complicated process actually locate Mobipocket vi