Generate a signal FGEN 5421 and gettting on FScope 5122

Similar Questions

• Connection diagram missing in DAQ Assistant generate the signalling block

  This is my first post so please excuse the quality of my description.

  When I double click on the block of data acquisition - Assistant, there is no tab connection diagram I can access to see how things are wired to the top. I have a NI USB-6211 connected by USB and it is used to control many different sensors and a power supply. Currently, he works for everything and is hard wired correctly, but only blocks DAQ Assistant has a connection diagram available, the other are not. One who has a connection diagram is used to measure a voltage. Others who do not are used to generate a signal. I would really like to be able to see patterns of connection for each block.

  -Any help would be appreciated

  -Thank you

  You can always do like those who never use the DAQ Assistant and read the manual. Right click on the device in MAX and selecting "stitching of the device" works too.

• Weird behavior with Signal to simulate and loops

  I'm having a weird behavior with Signal to simulate and while loops. Attached a photo of my program. The problem I have is that when I use Stop to stop inside while loop, then use to restart the inner loop, simulate Signal instantly generates a bunch of points of data between when I pressed Stop and Go. By example, if I stop for 5 seconds, wait 5 seconds, then press Go, it will instantly generate data for t = 5 t = 10. What I need is for the generation of signals to stop when I press stop and continue where it left off when I press Go. How can I accomplish this? I have no idea why he exhibits the behavior described in the first place.

  Hi optometry.

  Can you give us a screenshot of the configuration window for the VI express to simulate signal? I was able to reproduce the problem when I used "Simulate the time of acquisition" at times, but the VI's are featured as you described you wanted when I used "run as fast as possible." Have you tried this setting?

• I can't generate multiple signals with different phases.

  Hello community!

  I created a simple signal generator versatile (see Signal "Generator.vi"). When I try to put two of these generators in the same VI ("testbed non working.vi"), I'm not able to independently change the phase of the two signals. Only one of the two phase buttons actually modifies the two signals, while it has no effect.

  However if I copy and paste the exact schema even twice in the same VI, rather then import VI Builder, everything works fine ("Test Bench working.vi").

  It seems to me that the two generators are sharing anything other than the phase variable. I'm new to LabView and I can't understand what is happening and how to fix it. Can you please help me understand?

  Thank you very much

  Hello

  This is because multiple instances of the basic vi function generator will work regardless - they share information.

  To fix this one true constant wire to signal to reset the basic vi function generator enter your generator of signals vi.

  Best regards

  Florian

• How to generate analog signals?

  Hi all

  I'm trying to generate analog signals to simulate the position of the valve. I also want to simulate the position of the valve 0 - 5V (analog signal).  I've implemented the numeric position of the valve by using the toggle switches, but I want to implement analog signals.

  You can help.

  Thank you

  You can just use a random number generator.

  

  Since you have no generator hardware signals of NOR, I'm not sure why you are posting to this Board. Generic questions of LabVIEW. Post to this Board.

• Enter DAQ Signal kept rising and if stop Max voltage when it is run with nothing attached

  I just installed card PCI-6229 and a BNC-2110 (Labview 8.6V). When I started entry DAQ signal kept rising and stop at the max voltage (10V) operating with nothing attached (instead of changing to 0 all about). I was wondering what is the problem with him and how to solve. Configuration of terminal was "differential".

  I just created a DAQ entry with range and loop watch. Please let me know if I did something wrong

  Thank you

  I just reread your original post.  Why do you have the terminal setting to differential?  This looks like one configuration over for me.  Change the terminal setting in CSR.  With a differential setting. you need connect an AI1 source and another source to AI9.  The difference between the two will be reported.  With CSR, will count only AI1 and tension concerning the ground will be reported.  Make sure you have your AO ground related to your soil to HAVE.

• Conection lost to esp5200 kodak printer signal is excellent and still high tower failed to connect.

  can't conect printer

  conection lost to esp5200 kodak printer signal is excellent and still lap top cant conect

  Hi FrancesFlores,

  ·         What operating system is installed on your computer?

  ·         What happens when you try to connect to the printer? You receive an error message or error code?

  ·         Did you do changes on the computer before the show?

  Please answer the following questions so that we offer in addition to the steps to solve the problem of troubleshooting.

  During this time, you can consult the following articles and check.

  Install a printer on a home network

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer-on-a-home-network

   

  Share a printer

  http://Windows.Microsoft.com/en-us/Windows7/share-a-printer

   

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Hope this information helps.

• I got my redemption code. When he asks me to sign seeking a password with upper and lower case. When I enter a password generated, it recognizes my email and account and ask my original. When I get my original password he won"

  I got my redemption code. When it asks me to connect, it wants a password with upper and lower case. When I enter a password that I generated, it recognizes my email and account and asking my original password. When I get my original password it will not accept it. I'm going in circles?

  If you are unable to log in with your password, you can reset it. If you need help with it, please Contact Customer Care

• Frequency minimum step length and duration list minimum for the frequency lists in the generator of signals from NI 5406

  Hello

  We need power RF amplifier with a function generator to create plasma in an ion source. The signal pulse duration must be 1ms long, repeated twice per second.

  Today, we work in the following way: we spend the RF with f0 (aprox 1,995 MHz) frequency. After 20, we send a trigger signal passing frequency f1 (aprox 2.005 MHz).  We keep this frequency for the rest of the pulse.  However, the plasma that we generate is not 'constant' or stable during the whole impulse. If we smoothly change the frequency during the pulse we could improve.

  We would like to do: use the frequency sweep: rather than use this frequency hopping, we would like to move smoothly f0 f1 (frequency scanning). Then F1 to f2.

  As we have a PXI for data analysis, we believe using the arbitrary function generator of NOR: 5406 of NEITHER allowing the frequency sweep. However, in the book loads, it is not very clear, and I have a few questions:

  -We can create a "list of frequencies. In the site OR below, it shows that the "minimum of Step' is 1.28us, which would be ok for us (I understand that the"minimum duration of Step"is the minimum time between 2 frequencies). However, the manual of the device "NI PXI/PCI-5402/5406 specifications" said the frequency list has a time step of 1 ms to 21s. What is the good?

  -It is also said that the "duration of minimum list" is 1 s. For us, need us a shorter list that 0.5 seconds (we need to repeat the same pulse twice per second.). Is it possible to do what we want?

  -At the end of the day, we would like to implement a control loop which modifies the list of frequencies in real-time.

  http://zone.NI.com/reference/en-XX/help/370524L-01/nisignal_generators_help/features_by_device_smc/

  Thanks for your help.
  Best regards
  Jose.

  Hi Jose,

  You're right about the inconsistencies of the documentation. The minimum step was of 1 ms, but was changed to 1.28 µs to driver version 2.6. The help document has been modified to reflect that, but the specifications were not. I'll make sure that attaches.

  The length of the minimum list is not listed in the book loads, and the latest version of the help the signal generators OR (driver version 2.9) lists the minimum list than the 1 step length. Aid has changed to the driver version 2.6.1 to clarify that the 1s meant 1 step. I've attached a screenshot of the help of the most recent.

  There is an example that is installed with the NOR-FGEN driver called "Fgen Sweep Generator.vi". I would recommend from this for your application.

  I hope that some of the inconsistencies in our documentation brightened. Please let us know if you have any other questions.

  Elizabeth K.

  Generators of signal produced technical support engineer

• DAQ traditional and generator of signals of NOR-5401

  We have an older system using a signal generator of NOR-5401 (S/N 183962E-40) that runs with FGen 1.5.1 and 7.1 of NOR-DAQ

  We just bought an another NOR-5401 (S/N 192888 A - 01) to install a second system.  However, it does not work with the software.  The software uses traditional DAQ. If I look in MAX, the NOR-5401 on the new system only comes in the DAQmx instruments.   On the old system, the NOR-5401 is available as traditional DAQ.

  If I install an earlier version of the FGen (2.0 is the oldest, I can find) and NOR-DAQ 7.1 then the PC does not find a driver for the new OR-5401 at all.

  Should what versions of FGen and NOR-DAQ I install to make it work?

  Kind regards

  Keven.

  
  

• How to set the output meter channel to generate a signal pulse using DAQ6008

  Hello there I am generating a pulse signal of 100 Hz and a duty of 20% of the 6008 data acquisition cycle using visual studio 2013. I have code that needs to generate this but I'm not sure on how to set the channel output meter. When I run this NI MMAX and my vb error code indicates that the physical channel is not supported. I am a user of data acquisition were first and would appreciate any help offered.

  If you look at the USB-6008/6009 User Guide and specifications, you will see that the counter in these devices cannot rely as edges of entry. It cannot generate a pulse.

  Lynn

• 33522 A function / arbitrary generator of signals, 30 MHz

  Hello!

  I got 33522A function / arbitrary generator, 30 MHz. I want to make two squares of 30 kHz signal, one on each channel. Trick is that the waveform must be a reflection. I have a problem is, I was wondering if these signals is sysncronise if I drive it through LabView.

  I played around with one of them in the past, and these signals must be synchronized without any special order.

  This can be done on the front of the unit or through LabVIEW. The easiest way to set this is that same string except for the amplitude parameters, make the amplitude of a negative output from the other output.

  One thing to know...

  Although that synchronized, sometimes there is a difference in light phase between the two signals, you may need to adjust the phase of one of the signals to match the other. This is best done with an oscilloscope.

  See you soon,.

  McDuff

• Generating the signal as shown in the picture in labview

  Hello

  I'm using labview in 2011 and want to generate the second signal as shown in the picture attached in labview as I want to use it as input to implement adaptive filtering, if the first signal in the image represents the output of the adaptive filtering area.

  May I know how to generate a second signal.

  Thank you.

  
  

• How to connect the generator of signals of Agilent N9310A chauffeur?

  Hello

  I have a N9310A of Agilent connected via USB to a system using Labview 8.2 and the Agilent driver.  The system goes into remote mode, so there is a communication. I tried to change the example of "Agilent N9310A RF Output" to exit BF (low frequencies) so that I can check the control of the signal using an oscilloscope gererator.  I get the following error: Hex 0xBFFF0015 timeout expired before the operation is complete.

  I must then disconnect and reconnect the USB cable that the example can not find the device.  What happens here?

  I'm new to using Labview with tools

  -Thanks for any help

  -Matt

  Thanks for your help guys. The problem ended up being with the firmware of my Agilent N9310A signal generator. I got the A.02.03 firmware version and an upgrade to the current version (A.02.05) fixed something called an unstable connection between the PC and the N9310A.

  This works.

  -Matt

• A signal ramp monitoring and verification of the range thresholds

  I have a signal that ramps at 0.05 volts/second.  During this State, it is possible that the speed of ascent

  exceeds the operation 0.05 v/s (runaway condition).  Anyone has any ideas on how to follow it and

  meet the condition of runaway?

  Are you using the production of point-by-point samples or generate the samples in table form. Solution whole Tim is the most simple and works well.