Glass printing

Similar Questions

• How can I clean cloudy glass below the printer?

  I have a HP Photosmart 2600xi which the underside of the glass became cloudy with poor scan quality resulting.  No idea how to get under the glass to clean it?  Thank you!

  It was not the complete answer, as my model 2610xi is similar but different (newer) than the models in your manual.  The manual helped me to get the glass printer out, but I couldn't get it back in because I couldn't get off the front of the bezel.  I understand there is a trim Strip which must be forcibly jacked off the printer to access the two screws more below.  Then I was all ready!  The document also helped explain what type of cleaning use - distilled water (no happy to distort the image of the sheet metal is my guess)- and how to get down the Control Panel, disconnect the Ribbon cables.  So thank you very much because I did the work.  I was able to remove the glass and clean below... amazing how glass is now, and as a result my scans are much clearer.  Thank you very much.    -bbqdays

• HP printer Deskjet 2640 series: fax

  Dear Sir.

  I got the HP printer Deskjet series 2640.  I loaded original print - upward in the ADF, but sent fax was totally empty. Please specify if the original print - side must be kept down in the ADF.

  I look forward to your return expeditiosly.

  Kind regards

  Devinder Kumar,

  electronic mail; [Personal information]

  @Jindi

  Jindi wrote:
  

  Dear Sir.

  I've read page 34 of the user guide which specifies that the print to the top side should be loaded into the ADF, but it does not work. Please review & confirm how the print side must be loaded in the ADF, upwards or downwards.

  Kind regards

  Devinder Kumare-mail; [personal information]

  Place a sheet of the faxed document glass, print side down, and make a copy.  If the copy comes out blank or if the copy is hard to read, the likely faxed version no longer works.  This could be the result if the document by fax is on yellow paper or other (perhaps) due to the low contrast.

  If the copy is good, take this printed copy and put it in the ADF, side to the top and make a copy.  Evaluate the results.

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  Fixed / responded? Click this post accept as Solution to help others find answers.

• HP Envy 5660 all in a single printe: hp envy 5660 copy: Page size difference.

  I want to copy something that is maybe a page 11 standard 8 1/2 x 5 x 7.  I don't want resized or centered, just copied. The printer ejects a page and says "Page size disparity."  If I press OK, it ejects another page and gives me the same message but with the provision that accept the shift, it will print. It prints, but regional element.

  If I place the smallest element on the glass printed and put an 8 1/2 x 11 sheet of paper on it, it still gives the size mismatch error. What I'm trying to make is so common, I can't believe that this printer is unable to do so.

  I understood our problem and it wasn't a lack of software update. The setting for the main paper tray was 4 x 6 inches. We had removed the top to change the paper and, as the lower tray was never released, it doesn't reset it puts to be turned back in. To watch the small video who advised pulling on the lower plate to change the paper, I tried and was introduced by an "OK" button to confirm a change of paper size. After that, we were able to do all sorts of copy that we needed.

  Thanks for your help on what has been somewhat of a wild goose chase.

• C309a does not print

  My C309a all-in-One printed perfectly for 1 year.

  I went to copy a letter on the glass bed. He looked at the print head printing, but the document was empty.

  I then tried to print a Word and a .pdf document. The paper loaded correctly and the print head struck that it was printing, but the document was empty. I replaced all ink cartridges. I removed and cleaned the print head. I ran a test print which was OK and made a head alignment. What impression over the small screen on the printer says "alignment failed".

  Someone know why does print not now when powered by my computer or will not print when copying from the top of the glass printer? Print head looks like it's printing but nothing on paper.

  This questions the printer head problem. see the following steps for cleaning print head:

  • Click the Start button, if you have Windows XP. If you have Windows Vista, click the Windows icon located in the lower left corner of your computer screen.
  • Click on "Control Panel", then "printers and other devices. Finally click on "View Installed Printers or fax printers."
  • Right-click on the name of your printer and choose "Printing Preferences". This should open a new window; Then look for a tab or button labeled maintenance, or something similar.
  • Find the button that says "Print heads" or "Clean print heads" and click it. You may be asked to choose the print heads; Choose them all if you are. Make sure that there is no paper and ink in your printer, and it is turned forward.
  • Remove the page that your printer has printed and see if there are the missing gates or boxes. If it does not exist, you can just exit the program - your print heads are not blocked. If there is missing grids, then click on the "cleanup" or even button labeled.
  • Once you have finished the cleaning, print another page to make sure that your printheads are is more clogged. If they are still clogged, repeat steps 1 through 5 until your printer is printing clearly.

• HP Officejet 5745: Printing problems in glass

  The printer works fine when printing from the computer, however when I print from glass the printer emits mechanical noises and takes several minutes to print a single page.  This has happened once before about 6 months ago and it took a whole day to find someone to help me to understand.  If anyone has had this problem or knows how to fix?

  Hello, I finally talked with customer support and they solved my problem in about 20 minutes.

  Thank you for your help.

• HP Photosmart 5520 All in One printer cancels an order of copy of the glass

  HP Photosmart 5520 All in One printer & HP Pavilion dm1 Notebook PC

  I put a document on the glass of the printer to make a copy. The command is recognized, but cancelled immediately. The first two attempts were given a bit of text/photo about 1 centimeter.

  I used the doctor scanning HP and installed my printer again, but that has not helped.

  RodeDraak

  Hi RodeDraak,

  Given that the problem occurs when you run a copy, I hope that the problem is the printer hardware not the software on the computer.

  You have the printer connected directly to a wall outlet or is this a surge protector or power bar? Even if you have used a surge protector/power bar this whole time and you feel that this is not the case, please connect to a wall outlet so that we can eliminate the source of energy as the primary cause.

  Issues when connected to an uninterruptible power supply/Strip/surge protector power

  In this document, you will see,

  QUESTION:

  Questions or problems may arise when a HP LaserJet printer is connected to a UPS (UPS), a power strip or a surge protector

• My Hp 8600 more custom print or scan more from glass

  I have a HP 8600 Office pro jet which works OK, but suddenly it I cannot print or scan by placing a document on the glass.  I can print from my computer, but not directly from the printer.  I get an error message telling me to ' reload original in the ADF and try again "or an other error message telling me the ADF is blocked.  As I'm not using the ADF, it is meaningless.

  I tried to turn off the printer, disconnect, leaving for 5 minutes and try again, but this is not enough.

  Very frustrated because I need to analyze urgently!

  Maybe there is something in the adf file that triggered the detector? Try to lift the scanner see if there is a piece of paper or something stuck in there to open.

• HP 4500 wireless printer: printer all-in-one cannot scan glass

  My hp 4500 wireless printer worked fine until it just stopped printing.  I reintstalled the original installation disk and printing has been repaired.  However, the desktop icon for the hp Solution Center, which allows scanning of computer files, has not been activated, and accordingly, I am unable to scan from glass.

  New driver from HP site could not install completely and still have the same problem.  I tried to reinstall the existing drive, and it is still able to print, but still can not sweep.  The desktop icon is always off.  Didn't test the fax.

  I have here an updated driver that contains the implementation complete for the 4500 Wireless: G510n-z

  My system is Windows 7 64 bit.

  Please answer.

  Hello @rudetom,

  I would like to see if I can help you get your Officejet 4500 Wireless software working again.

  Looks like pieces of old software is causing the installation to fail. I would like to clean at the far (unisntall) and try again.

  When you have uninstalled the printer software, it is possible that pieces of it may remain which could interfere with a reinstall. I recommend referencing the steps described in this document to make sure that you haven't missed anything whatsoever; Uninstalling the printer software. * If you are connected with a USB cable, be sure to unplug it.

  You can also delete files using disk cleanup - take care to put check marks in selection boxes when it is available.

  Software drivers can hide other places would be in your device manager.

  To open Device Manager:
  ' 1) click on start (Windows icon) and enter the Device Manager "in the search field.
  2) click on Device Manager.
  (3) you can click on View, in the upper windows and then show hidden devices.
  (4) to develop the types of devices and check for any pilot associated with your printer.
  (5) to remove a device from Device Manager, right click on the device name in the list and then click on uninstall.

  For more information, see device for Windows 7 Manager information.

  Once you have removed everything, I restart your computer and then try to download the new software again to HP Officejet 4500 Wireless - G510n full feature software and driver.

  If you still have problems, please let me know what kind of error you get and how your printer is connected to your computer. What is direct installation USB or wireless?

  Please let me know if any of these steps has resolved your problem, or if there is anything else I can do to help.

  I look forward to hear from you!

  Thank you

• HP Officejet Pro 8600 Plus - printing of Documents for glass copy and charger slowly

  We bought this printer a few months back, and everything was working great. Yesterday afternoon, the COPY works, the high plateau of the loader page or the scanning tray, from work extremely slow. If I put a document on the glass and do a preview, it shows the preview a few seconds. The question arises when you print the copied document. He made several noises and, a minute later, finally then prints it. If I have something to print from my computer (connected with USB) it prints quickly. Even on the internet with my phone. I tried to change the normal paper but also the project and best, without change. Help, please. :/

  Rich1,

  Thanks for your reply. I plugged directly into the wall after reading about it, some problems of fixing on the forums. He has nothing. I finally got annoyed when the problems started affected the printer completely. Three different people take off open back the front, looked on all the rolls and nothing found. I tried to check the ink cartridges to ensure that they have been inserted correctly. As I put my head down on the desk of boredom, I saw... A whole piece of the book all the way inside the printer behind the control panel. He managed to crumble by preventing sliding back properly and through the printer ink cartridges. I asked 2 people to come and look and see if they could find the same paper. No luck, lol. I showed them exactly where and they both were surprised that the size of the paper, and that they could not find. in any case, removed the paper... it's fixed! Thanks for the support! God bless you!

• OfficeJet Pro 8610: Printing from the surface of the glass

  When I use the scanner glass to print a 8-1/2 x 11 page, I get an impression that indicates the size of the entire glass.  In other words, I get the height 11 "(slightly reduced) and a 1/2" space at the top (or bottom).  How do I change the setting so I print only the original and not glass?

  Hello

  Your printer cannot print from glass. Are you talking about copying (similar to the copiers)? If so, please try the printer control panel:

  b press copy,

  (b) press settings (Gear icon in the lower left),

  (c) based on the size of the paper.

  (d) select the size of the list,

  (e) return (closed arrow) key,

  (f) touch black or color.

  Kind regards.

• HP Officejet Pro L7788: impossible to scan/print on my officejet pro l7788 glass

  I can't print or scan with my all in one HP Officejet Pro L7788

  I try to use the glass, and he doesn't even move. It is only by using the top drive. I don't know why. I have no paper, only on the glass. And it does not work for either. I don't know what to do. Its really pissing me off.

  It is connected by USB.

  Best work properly either. It was when first, you have the printer not for long.

  Print and scan from different programs?

  Yes, I have uninstalled and reinstalled the program

  I have Norton

  Disable my antivirus? I just got it recently. So I don't think that's the problem. but who knows

  Earlier, I ran the Dominican Republic and my test print came out bad, after evaluating it well enough get the heads cleaned and aligned. I did the same thing * beep * several times. Its getting old! In any case, I did two test and they are not 100%

  I not did nothing to my whole upward. When I first came to this printer I actally printed and scanned picture perfect. Now, it does no good.

  I have the printer connected to the surge.

  Updates for my windows... Perhaps. It updates automatically things

  the usb cable seems to be well. I don't think that's the problem

  I also tried scanning a page with written things on and when it printed the page came out all messed up children. Not a single thing written on the original was released.

• hp 8600 Printer Wizard automatically opens when a document is placed in the scanner glass?

  I recently bought a HP 8600 Pro multi use printer. When I place a document on the scanner glass or Peter assistant printer does not open automatically. It's a convenient feature on my previous HP printer.

  The wizard can be obtained by double-clicking on the desktop icon, but it's a bit bulky. I wonder if this feature was removed for some reason, or I do not know how to operate it.

  Any help would certainly be appreciated.

  Hello

  No, it's not a sensor to do this bit.

  Kind regards.

• My 3-in-1 uses the color cartridge for copy/printing black a black paper on the glass top...

  My 3-in-1 uses the color cartridge to black for a black document on copy/printing tray, but use black cartridge to print in black from the computer itself.

  In other words:

  (1) if I have a document with a black print in Microsoft word on my hard drive and I want to print this document in black print, while the 3-in-1 works fine. In other words, is the black cartridge can print a document in black to a black document.

  (2) if I take this same document which has just been printed in black and put one on the glass and try to produce a black document thereof using the copier function, the 3-in-1 uses the color cartridge to produce the black document... .more is very slow (the same speed it would be if I were to produce one side of color of color documents.

  Of course, it cannot be the black cartridge.

  Through a long trial and error process, I got lucky and I resolved and the resolution is not what I was expecting and makes no sense to me.

  Use the settings of the printer itself, I just changed the setting from "automatic" to the "plain" paper and the setting in 'text' value 'None '.

• do not tray or glass HP Officejet 6500 wireless print

  Printer is not tray or glass image capture. The new page goes through the printer very well but it is empty. Print many of the computer.

  Hi RT47,

  Which of the following is your printer?

  HP Officejet 6500 - E709n wireless all in one printer
  HP Officejet 6500 - E709q wireless all-in-one printer

  Do you get any error messages?

  Try to do a Hard Reset as described in the folloing link.  Click here  Y at - it change?