GPIB error with several bee feeds

I use the code of this package of vi:

http://sine.NI.com/apps/UTF8/niid_web_display.download_page?p_id_guid=E3B19B3E9635659CE034080020E748...

and I tried to connect two power supplies to GPIB (with one off the power supplies).  When I run the simple Bertan 225 I get the following error code (see attachment as well): 1073676294 and the tension does not read correctly.

When it is the only bee feeds is connected to the GPIB I don't get an error and the voltage is read correctly.

Thanks for any help,

Kevin

You should not use GPIB with 1 of the 2 instruments turned off. The specification requires that two-thirds of the devices to power. Turn it on and see if the warning (NOT error) disappears.

Tags: NI Software

Similar Questions

  • Error with several owners user ID: ImageFrame owned bt PagePageItem and BaseLink

    After you install the update of Muse, I run my site work active and immediately saved the file. But I get the error message: uid with several owners: ImageFrame owned bt PagePageItem and BaseLink. And the program of the muse stops.

    Anyone know what it is.

    There is a problem in the original .muse file. Muse made a diagnosis of the State of the file in the framework of Save as. That check detects a problem that unfortunately requires that we take a closer look and the manual of repair by cracking open the file. (You will get a similar error if you had made a save as in the previous version.)

    Please send us the .muse file at [email protected] as well as a link to this topic. If the file is larger than 20 MB, you can use a service like Adobe SendNow, Dropbox, WeTransfer, etc. (if you use a service, please include your email address in the body of the message back, given that not all services to include it in the invite sharing they send.)

  • Driver for Keysight 34461 A DMM instruments works with GPIB, errors with USB

    I try to remotely control a DMM of 34461a Keysight using the driver of instruments located here:

    http://sine.NI.com/apps/UTF8/niid_web_display.model_page?p_model_id=21589

    The pilot of the aircraft works like a charm the DMM is connected via GPIB, but it error when connected via USB.  I've isolated the problem to "Default Instrument Setup.vi".  When this VI is called in the case of USB, the device is left in a State which translates by a later call a time-out at VISA Read.  The only way I found to get the instrument still talking after this occurs error condition is turned off.  I have an another 34461a with the same behavior, is probably not a hardware problem.  I can successfully run the example 'Agilent 3446 X series Acquire Single.vi' via USB if I remove all calls to "Default Instrument Setup.vi.

    Everyone knows this unit or a similar problem?

    I use Windows 7, 2014 SP1 LabVIEW, NI-VISA 14.0.1 and GPIB-USB-HS + (OR-488. 2 14.0) when using a GPIB.

    Since the Readme file

    3 known issues

    Agilent IO Suite must be installed to use the USB interface.

  • Firefox running error with several profiles and - no.-remote set

    I created two profiles. One turn firefox 4 and one for firefox 3. I run both for test purposes in an environment of websolution. The profiles are called respectivally firefox4 and firefox3 and these are the only profiles. I changed the shortcuts to read
    Path/to/firefox4/Firefox.exe Pei firefox4-no-remote
    and
    Firefox3 Pei Path/to/Firefox3/Firefox.exe-aucun-distant

    Now I can start two versions of shortcut there at the same time. But when firefox 4 is open (I want to use it as default browser) and I clicked on a link in another program (i.e. a link in an email open in thunderbird or from a twitter app) I get an error:
    Firefox is already running but is not responding. To open a new window, you must first close the existing Firefox process, or restart your system.

    I thought that with you-no-in case of problems of distance options like this. Is there something I'm missing or is there a fix for this problem?

    You cannot use the -no-remote command for a profile that is the ' default browser / profile ".

  • Errors with several buttons pointing to the same frame on the timeline. Animate CC

    I have a project where I'm using a function text button to reach a specific image and stop to view, however, if I take a contour of the object and put it on a symbol, I can't have two different objects pointing to the same frame, it generates the error because the frame can be called only by a single button/symbol.

    My solution is to reproduce each of the frames and each have addressed as a new image with the same content.

    Is there a better way to do this?  I'm not fluent Actionscript 3.

    Thank you

    Rick

    You can't have double function names and using the same name/instance for different objects reference is problematic, but you pouvez have different objects "..." pointing at the same time.

    Btn1.addEventListener (MouseEvent.Click, F1);

    btn2.addEventListener (MouseEvent.Click, F1);

    btn3.addEventListener (MouseEvent.Click, F2);

    Function f1(e:MouseEvent):void {}

    this.gotoAndStop (32);

    }

    function f2(e:MouseEvent):void {}

    this.gotoAndStop (32);

    }

  • error with several timers

    I basically have a compass and I want to have the pointer to stop every 15 ° for a certain period of time. The first timer works fine, but the rest pause longer. And they vary.

    It's code for the first break:

    Stop();

    var fl_TimerInstance_1: timer = new Timer(1000, 30);
    fl_TimerInstance_1.addEventListener (TimerEvent.TIMER, fl_TimerHandler_1);
    fl_TimerInstance_1.start ();

    var fl_SecondsElapsed_1: number = 1;

    function fl_TimerHandler_1(event: TimerEvent): void {}
    Play();
    fl_SecondsElapsed_1 ++;
    }

    For the second:

    Stop();

    var fl_TimerInstance_2: timer = new Timer(1000, 30);
    fl_TimerInstance_2.addEventListener (TimerEvent.TIMER, fl_TimerHandler_2);
    fl_TimerInstance_2.start ();

    var fl_SecondsElapsed_2: number = 1;

    function fl_TimerHandler_2(event: TimerEvent): void {}
    Play();
    fl_SecondsElapsed_2 ++;
    }

    With the help of Flash CC

    Thanks in advance

    AS3 has setTimeout, which can be much easier to use and less wrong. Try to put this script every 15 frames in your animation:

    Stop();

    setTimeout (play, 1000);

  • Carpet * a DVD-Ram UJ - 841S comes with several error messages

    My laptop is relatively new, I've been burning some video files in DVD - RW and all of a sudden my DVD drive has stopped working. It came with several error messages format "failed due to damage media", "format failed due to general failure" and "the inserted disc is READ only".

    I also can't rip music discs.

    Can you see ODD listed in Device Manager, and if so what is the exact status it?

    Sorry, but we discus on ODD, but nobody knows what model of laptop you have and what is the history of this problem. Is replaced the drive? Why are you sure that you are using compatible with your laptop ODD.

    Please more information!

  • Several pop-up windows "Security Fix" indicating the many problems w/computer & scan to see what they were. returned with several "critical" errors & several "warnings".

    Original title: fix the system

    While the site of the car got several popup windows "Security Fix" indicating several issues w/computer & scan to see what they were.  Do that & came back with several "critical" errors & several "warnings" says had to buy the program to correct.  Then stop computer & when turned on the next morning the only office was trash & start menu is empty with the exception of all programs.  Went to windows defender for all programs & said it was off?  I didn't turn it off & when trying to turn back & says cannot open program, error 0x800106ba.  Help!

    Do you have any antivirus, in addition to Windows Defender?

    System Fix is a fake program aimed at obtaining the payment card information. If you have used your card with it, contact your card provider immediately.

    There are instructions to remove the difficulty here:

    http://www.bleepingcomputer.com/virus-removal/remove-system-fix

    Use only written instructions. Do not download anything from advertising on the Web site.

    This program can damage your computer and the removal instructions may not be completely effective.

  • I get this error "sec_error_ocsp_bad_http_response" on several sites with FF 6.0.2 and prior versions, but do not get the error with IE.

    I get this error on several sites, it's the latest on what he has just come. I got it by trying to sign on this page.
    I am able to connect using IE 9, Windows 7 Enterprise.

    What is the definition of OCSP?

    • Tools > Options > advanced > encryption: Certificates > Validation
  • Error handling in QMH projects with several sources of error

    Hi guys,.

    I have a head scratcher:

    QMH architecture, I have a state machine that describes a certain task of legislation on different instruments.

    Each of these instruments has its own message loop vi management and each of these loops could cause errors.

    I want to pass these errors to the state machine (VI main if you want) in order to take appropriate action or - at least - inform the user what the error instrument came. Currently, I use a global variable for each error source and merge errors in primary VI.

    Problem: Multiple errors, only the one connected to the first entry of the fusion VI errors is displayed.

    What is the best way to get errors from several sources to level superior screw and keep all the error information for debugging purposes?

    Thank you!


  • Interfacing with several unknown USB devices; all producing NMEA strings

    Hi all

    Question about the peripheral USB interface and their associated drivers.

    I have the obligation to build an application that interacts with the USB devices that produce NMEA strings. I have the library to parse NMEA strings, but I fight with interfacing with several unknown USB devices. When deploying applications, I know not all possible USB devices to use.

    Is it possible to produce one driver who will accept any USB device strings?

    Or, more likely, is there a way to get the LV to recognize a connected USB device and automatically find / install the driver like windows does and is it possible to do in a deployed application?

    I had a trawl of the forums, but I've not found anything that specific.

    Thanks, I really appreciate the help.

    About the VI "set up the serial port", my problem is that the choice of COM port is in a separate menu (not directly related to the VI) and it allows all possible COM ports to be selected. That can be addressed.

    I am not expecting an all-in-one solution but asked the question in case it was possible.

    What I realized, is that for my specific condition to read strings from a USB device. It is likely to be sent over a serial connection. LV can handle this well and easily assuming the device has the installed driver / settings are available.

    LV (and indeed any other program) will not work without a device driver / settings. In this case, parameters set must be found (error) / a USB RAW driver would need to be developed. Devices requirng a RAW USB driver would need a serious review to continue due to the time and effort required. All this effort is work inherited from the AIDS to navigation

    I appreciate any help and I think I got the answer I was looking for! Thank you very much

  • Closure of a state machine in queue event with several parallel loops

    I am trying to find the best way to stop a program that consists of an architecture of State machine in line waiting for event with several parallel loops. Can anyone recommend the best way to achieve this in my attached VI? (To browse the forum, this seems to be a frequently asked question, but I have not found a solution that works for me.)

    I look forward to any comments on my as well code, if someone is willing to offer it.

    My program needs:

    If the user press the 'Stop' button, the program should prompt the user with "are you sure you want to stop the program?" and then return to a State of rest or move forward to stop the program. In addition if there is an error, the program should prompt the user to ' clear the error and continue, or stop the program. Then back to the idle state or move forward to stop the program.

    Architectural details:

    The program consists of 3 parallel loops: (1) a loop of event management that places different States of a queue of the State, (2) a State Machine that enters the State that is removed from the queue of the State and (3) a loop error/Shutdown, which deals with errors in the error queue management.

    During normal shutdown, where running handling loop in the case of event 'Program.Shutdown' and 'Shutdown' and the 'Idle' States are added to the queue of the State. In the state machine, the State of 'Stop' is invoked. Special "5000" error code is added to the queue of the error. In the loop of error handling and stopping, "5000" error triggered a prompt that asks the user if they want to stop the program. If the user chooses not to stop, a notifier StopNotif is sent to the State of 'Stop' and 'Program.Shutdown' event case with notification 'Go '. If the user decides to stop, the Notifier sends the notification "Stop". Loop and event management State Machine ends when they receive the notification "Stop".

    In case of error, the program behaves in the same way: If the user chooses to clear the error and continue, the program returns to the status "pending".

    HOWEVER - if the user chooses to stop the program, the program crashes. The author of the notification that is sent to stop the loop of events and State Machine management cannot be read because event Program.Shutdown and the stop State (which contain the function "Waiting to notify") are not active.

    I was able to activate the stop State by Queuing in the loop of error/Shutdown management. But I don't know how to activate the "Program.Shutdown" event by program and thus access the function "Waiting to notify" inside.

    I tried to put the function "Waiting to notify" outside the structure of the event, so the event-handling loop never ends. Placing timeouts on the "wait for declaring" and the structure of the event makes the programme of work, but I want to avoid using timeouts because I don't want to turn my event program into a program of polling stations. I would also avoid using variables or nodes property to stop loops, because that requires the creation of a control/indicator for something that the user does not need to interact with.

    Thank you!

    First of all, close the notifier outside loops with your queues.  Second, you must use a user event to send the message to the event structure loop so that it stop in the case of the stop on an error.

  • UID errors with the new update - patch of potential symptoms

    Hello

    Short version - if you did anything to any element within your site from Muse SINCE the upgrade, look here for your solution of problem first. That's where I found mine.

    The long version - first of all, I must say that I am not a doctor so I can't cure what ails you. I can say that I have recently suffered some of the same problems described recently in this forum. In fact, for about a week or two. This is my error: "Adobe Muse CC has encountered an error and will now close. Please report bla bla.

    "With several owners of the UID: SVGPageItem owned by layer and ImageFrame.

    So I checked here and tried some suggestions on the forum visitors and moderators. My site weighs a little over 100 MB so I was not send in to Adobe for them to noodle around in. Call me paranoid.

    What I've done this as the requested message. Report of the last little action. For this I had to reconsider my actions. A new version of the site on February 19, and everything worked well, I had posted by FTP. A couple of days old, a customer sent a text to my site was "funny". Seems that some browsers could not find active made and so there were spaces empty and red x where the images should be. Not on all pages and not all images on a page, just a random sprinkling of the lack of content. So, today was the first time that I could close the door and really look at it. Wow. On first opening, I got 95 missing assets. I tried to recreate a link to an article and excluding Muse would go try to solve each broken link active. Muse never completed this task once in several trials. 1/3 has been progress before max than the above error message could interrupt growth. Then, I went through my files and pulled out all of the SVG content and isolated in a new folder, same directory. Nope. For some reason, I got two JPEG files in question before the message above would end new progress. Muse would not set just one active and stop, hell no. He feels the need to save me time, and so he tries to update ALL the missing links of the asset. Stop already nicaise? Another bonus to this was that muse not would you save other changes to your site once this issue of missing property has begun. I couldn't save it as. Now, I'm really stuck.

    I go into the files and look at the assets through my BONES and see nothing unusual.

    I try to open again the Muse and access the screen on missing assets and ignore it by going to file - open Site - name of file - open. I am able to see the page sitemap for my site. I go to the active panel and am able to recreate a link to my jpeg and png in all files except the main images folder. Muse crashes again. I open it again. Open a page (random selection) and go to the layers panel, select an asset I know is on the list to re-release select it. Success. After spending and manually reissue of active links individually, I could save my site without change of name.

    I closed and reopened and everything works as it should. I'll get some lunch now and trying to all download after lunch.

    If all goes well this will be the only post.

    No news is good news.

    I got a different error message towards the end but that was eliminated in the reissue of individual links of the assets.

    This is an image file with messages.

    SETTINGS2DELETE_Muse_relink_errors.jpg

    An update was released today, please install the latest update.

    Adobe help Muse | Release notes | Adobe Muse CC

    Thank you

    Sanjit

  • Book of 10 with several files frame crashing when I change the numbering at the level of the book.

    I built a picture book (image 10) with several files from a variety of books. The files have inlays of text and references to breast and between chapters. When I go to set the numbering at the level of the book - as soon as I click on the Numbering dialog box Set - Framework breaks down and I get an internal error 10024, 6382424, 6369627, 6383085. I have attached a screenshot.frame crash.png

    I take the files on the book and added back in. These files worked fine in the original books, that I copied them from. I can't get the book to number correctly. Help, please.

    Hi, Estelle,.

    Don't know if this is relevant to what you are feeling, but...

    I've encountered similar problems of numbering with several of my books.

    What fixed it finally for me, is that I discovered that some files were overrides of paragraph style (not necessarily related to positions or section heads.

    Once I removed all replacements of these files, numbering issues have been resolved.

    While I use the plugin Tools section , you can scan your files for the substitutions with built-in FM find/replace.

    Kind regards

    Amitai Sela

    Philips Healthcare

  • Doc protocal identification error with custom doc

    Hello

    I'll set up a scenario where the remote sends an xml file to the host. This is a custom xml file, and the b2b host should accept this file and the report properly within the scope of b2b.

    I created a custom B2b management document. For the customized document, I gave version, name of doc, doc definition as "custom".

    I created hosts, remote partners, agreements and deployed.

    I placed an xml (from xsd) file in the ftp folder. B2B reads the file in the folder ftp and gives error of identification Document Protocol. Please let me know if the steps I am following is correct?


    Thank you
    Ganesh

    Message from the company:

    ID 7F00000112AA1FF00AD0000034BD111D
    Message Id 7F00000112AA1FEF8CF0000034BD1119
    Refer to the Message to refer to the Message
    Type name of the sender
    The sender value Remote
    Type name of recipient
    Receiver Host value
    Distance of the sender
    Receiver host
    The agreement ID
    Agreement
    Type of document
    Protocol document
    Version of the document
    REQ message type
    Direction of traffic ENTERING
    MSG_ERROR State
    Mode of recognition NO
    ASYNCHRONOUS response mode
    Timestamp sent Tuesday, August 24, 2010 12:48:15 PM GMT + 10:00
    Receive information of an hour Tuesday, August 24, 2010 12:48:15 PM GMT + 10:00
    Cooldown document 0
    Remaining document retry 0
    3763 native messages size
    Translated Message size
    Name of the Action
    Name of Business Transaction
    XPath name1
    XPath Value1
    XPath Expression1
    XPath Name2
    XPath Value2
    XPath Expression2
    XPath Name3
    XPath Value3
    XPath Expression3
    Correlation of XPath name
    Correlation of the XPath value
    Correlation of XPath Expression
    Correlation with the name of XPath
    Correlation with the XPath value
    Correlation of XPath Expression
    The Message wire
    Application Message Message from the Application
    Payload, Payload storage
    Attachment attachment
    Label
    ID of the collaboration
    Collabration name
    Collabration Version
    Name of the Action
    Exchange generic name FTP protocol
    Version 1.0 of the Protocol Exchange
    The exchange control number
    The group control number
    Transaction control number
    B2B-50083 error code
    Error Description Machine Info: (localhost) Description: Protocol for the identification of the Document error.
    ERROR_LEVEL_COLLABORATION error level
    Severity of the error
    Text Protocol for error identification document.


    xsd:

    <? XML version = "1.0" encoding = "UTF-8"? >
    < xs: schema xmlns: XS = "http://www.w3.org/2001/XMLSchema" elementFormDefault = "qualified" >
    < xs: element name = "order" >
    < xs: complexType >
    < xs: SEQUENCE >
    < xs: ELEMENT ref = "order" / >
    < / xs: SEQUENCE >
    < / xs: complexType >
    < / xs: element >
    < xs: element name = "order" >
    < xs: complexType >
    < xs: SEQUENCE >
    < xs: ELEMENT ref = "orderheader" / >
    < xs: ELEMENT maxOccurs = "unbounded" ref = "orderdetail" / >
    < xs: ELEMENT ref = "ordertrailer" / >
    < / xs: SEQUENCE >
    < / xs: complexType >
    < / xs: element >
    < xs: element name = "orderheader" >
    < xs: complexType >
    < xs: SEQUENCE >
    < xs: ELEMENT ref = "deliverylocationcode" / >
    < xs: ELEMENT ref = "deliverylocation" / >
    < xs: ELEMENT ref = "deliveryaddress1" / >
    < xs: ELEMENT ref = "deliveryaddress2" / >
    < xs: ELEMENT ref = "deliveryaddress3" / >
    < xs: ELEMENT ref = "deliveryaddress4" / >
    < xs: ELEMENT ref = "invoicename" / >
    < xs: ELEMENT ref = "invoiceaddress1" / >
    < xs: ELEMENT ref = "invoiceaddress2" / >
    < xs: ELEMENT ref = "ordernumber" / >
    < xs: ELEMENT ref = "orderdate" / >
    < xs: ELEMENT ref = "means" / >
    < xs: ELEMENT ref = "requireddeliveryfrom" / >
    < xs: ELEMENT ref = "requireddeliveryto" / >
    < xs: ELEMENT ref = "terms" / >
    < xs: ELEMENT ref = "currencycode" / >
    < xs: ELEMENT ref = "currency" / >
    < xs: ELEMENT ref = "shippinginstructions" / >
    < xs: ELEMENT ref = "suppliercode" / >
    < xs: ELEMENT ref = "suppliername" / >
    < xs: ELEMENT ref = "supplieraddress1" / >
    < xs: ELEMENT ref = "supplieraddress2" / >
    < xs: ELEMENT ref = "supplieraddress3" / >
    < xs: ELEMENT ref = "suppliercontact" / >
    < xs: ELEMENT ref = "suppliertelephone" / >
    < xs: ELEMENT ref = "buyercode" / >
    < xs: ELEMENT ref = "buyername" / >
    < / xs: SEQUENCE >
    < / xs: complexType >
    < / xs: element >
    < xs: element name = "deliverylocationcode" type = "Integer" / >
    < xs: element name = "deliverylocation" type = "xs: String" / >
    < xs: element name = "deliveryaddress1" type = "xs: String" / >
    < xs: element name = "deliveryaddress2" type = "xs: String" / >
    < xs: element name = "deliveryaddress3" type = "xs: NCName" / >
    < xs: element name = "deliveryaddress4" type = "Integer" / >
    < xs: element name = "invoicename" type = "xs: String" / >
    < xs: element name = "invoiceaddress1" type = "xs: String" / >
    < xs: element name = "invoiceaddress2" type = "xs: String" / >
    < xs: element name = "ordernumber" type = "Integer" / >
    < xs: element name = "orderdate" type = "xs: String" / >
    < xs: element name = "means" type = "xs: String" / >
    < xs: element name = "requireddeliveryfrom" type = "xs: String" / >
    < xs: element name = "requireddeliveryto" type = "xs: String" / >
    < xs: element name = "terms" >
    < xs: complexType / >
    < / xs: element >
    < xs: element name = "currencycode" type = "xs: NCName" / >
    < xs: element name = "currency" type = "xs: String" / >
    < xs: element name = "shippinginstructions" >
    < xs: complexType / >
    < / xs: element >
    < xs: element name = "suppliercode" type = "Integer" / >
    < xs: element name = "name" type = "xs: String" / >
    < xs: element name = "supplieraddress1" type = "xs: String" / >
    < xs: element name = "supplieraddress2" type = "xs: String" / >
    < xs: element name = "supplieraddress3" type = "xs: NCName" / >
    < xs: element name = "suppliercontact" type = "xs: String" / >
    < xs: element name = "suppliertelephone" type = "Integer" / >
    < xs: element name = "buyercode" type = "Integer" / >
    < xs: element name = "buyername" type = "xs: String" / >
    < xs: element name = "orderdetail" >
    < xs: complexType >
    < xs: SEQUENCE >
    < xs: ELEMENT ref = "itemlineno" / >
    < xs: ELEMENT ref = "itemcode" / >
    < xs: ELEMENT ref = "DescriptionArticle" / >
    < xs: ELEMENT ref = "itemarticle" / >
    < xs: ELEMENT ref = 'itemsize' / >
    < xs: ELEMENT ref = "itemcolour" / >
    < xs: ELEMENT ref = "itemqty" / >
    < xs: ELEMENT ref = "itemunitcost" / >
    < xs: ELEMENT ref = "itemtotalcost" / >
    < xs: ELEMENT ref = "caseqty" / >
    < / xs: SEQUENCE >
    < / xs: complexType >
    < / xs: element >
    < xs: element name = "itemlineno" type = "Integer" / >
    < xs: element name = "itemcode" type = "Integer" / >
    < xs: element name = "itemdescription" type = "xs: String" / >
    < xs: element name = "itemarticle" type = "xs: NMTOKEN" / >
    < xs: element name = 'itemsize' >
    < xs: complexType / >
    < / xs: element >
    < xs: element name = "itemcolour" >
    < xs: complexType / >
    < / xs: element >
    < xs: element name = "itemqty" type = "Integer" / >
    < xs: element name = "itemunitcost" type = "xs: Decimal" / >
    < xs: element name = "itemtotalcost" type = "xs: Decimal" / >
    < xs: element name = "caseqty" type = "Integer" / >
    < xs: element name = "ordertrailer" >
    < xs: complexType >
    < xs: SEQUENCE >
    < xs: ELEMENT ref = "notes" / >
    < xs: ELEMENT ref = "taxreference" / >
    < xs: ELEMENT ref = "remarks1" / >
    < xs: ELEMENT ref = "remarks2" / >
    < xs: ELEMENT ref = "TotalCost" / >
    < xs: ELEMENT ref = "totalsticks" / >
    < / xs: SEQUENCE >
    < / xs: complexType >
    < / xs: element >
    < xs: element name = "notes" type = "xs: String" / >
    < xs: element name = "taxreference" >
    < xs: complexType / >
    < / xs: element >
    < xs: element name = "remarks1" type = "xs: String" / >
    < xs: element name = "remarks2" >
    < xs: complexType / >
    < / xs: element >
    < xs: element name = "TotalCost" type = "xs: Decimal" / >
    < xs: element name = "totalsticks" >
    < xs: complexType / >
    < / xs: element >
    < / xs: Schema >


    XML:

    <? XML version = "1.0"? >

    < commands >
    < order >
    < orderheader >
    < deliverylocationcode > 16 < / deliverylocationcode >
    ......................................................................................................
    < TotalCost > 2580.00 < / TotalCost >
    < totalsticks > < / totalsticks >
    < / ordertrailer >
    < / order >
    < / order >

    Hi Ganesh,

    Have you provided Identification (XPath) Expression correctly in the document definition? Please check.

    You can consult the section "7.1" using custom Document Protocol on link - below

    http://download.Oracle.com/docs/CD/E14571_01/integration.1111/e10229/b2b_documents.htm#CHDEFFEH

    Kind regards
    Anuj

Maybe you are looking for