GPS Toshiba NB200 problems

Similar Questions

• Toshiba NB200 - startup problem (Windows XP) - unable to access safe mode

  Hello

  I have a laptop Toshiba NB200 with Windows XP. When I turned on, it would not start past the first screen and I couldn't make F8 safe mode.
  The only thing I can do is go into the BIOS Setup, and that's all (press F12).

  The BIOS recognizes the hard drive. Then, I created a USB stick to boot from and that made me a C: quick MSDOS having first changed the BIOS to read the USB first and also updated the BIOS (Phoenix v1.6).

  I'm not clear as to what I do then in the folder c: prompt will not let me run windows and shows just the files on the USB key.
  Should I copy the files from windows to the USB port? In addition, how will I know if the hard drive has failed and that it is unrecoverable (I hope not)?

  Any guidance welcome!
  Thank you

  Hello

  Eventually, there is no Windows OS on the HARD drive and therefore you can not start safe mode or the OS.
  You have a recovery disk or you did backup the image of Toshiba on the USB flash key?

  If this isn't the case, then you need to reinstall the OS of the own Windows XP CD.
  You could build a clean Windows XP USB flash stick that can reinstall the OS.
  I think that this should be possible since you started the laptop backpack.

  Here's a nice instruction how to do this:
  http://wiki.EeeUser.com/windowsxpusb

  Good luck

• Toshiba NB200-10Z change HARD drive to SSD

  Hello. I plan to buy Toshiba NB200-10Z netbook. I would like to ask if the next drive 'OCZ-OCZSSD2-1VTX60G 60 GB Vertex Series SATA II 2.5 SSD Drive' will fit this netbook?

  Post edited by: Lee

  Hello

  The SSD must fit into the laptop with no problems, because it s the same size as a HDD normal (2.5).

  The point is if SSD drive will work in NB200. Normally, an SSD should work on all SATA interfaces, so in your case, I would try an SSD.
  After that, you can validate the experience with this player. I am interested in. :)

  Good bye

• Toshiba NB200 Touchpad not smooth?

  I bought a Toshiba NB200-10Z this week and I am satisfied with my purchase, very elegant. The only thing is that if my fingers are dry the touchpad feels a little rough smoothly, by sliding your finger over it. But if my fingers were a little moisture on its fine and smooth to use. Everyone is faced with this problem? I don't think it's a problem with mine individually I think it's the texture of the touchpad.

  Thank you
  Ben.

  Hello

  I never noticed this issue with touchpad surfaces.
  If you are talking about the touchpad feature then I would recommend checking the touchpad settings in Control Panel-> mouse
  Here, you can edit and assign different options that could help you make the most sensitive touchpad

  See you soon

• Unable to charge the Toshiba NB200 at all

  Hello

  I recently bought a Toshiba NB200 and after that the battery has finally failed, I tried to load but to no avail. When I plug in the charger, the sheet of light at the bottom with all other types of lights (HDD light, seeing the battery etc) shined green while the battery light was orange all the time even if I left it for a long time. Every time I tried to turn on the computer, while the "charge", only, I could get as far as the windows start page when it turns off by itself because of the low power.

  What problem I have because it seems weird that the plug led is green while the battery light is still orange after a long period of time.

  Is there anyway that I can fix this problem or any other method if this problem cannot be solved?

  (Well a point to note is I bought my laptop in Thailand and it loads fine, but when I got the laptop, I can not load but the thing is that I brought my laptop previously bough Thailand to Singapore and it worked fine, so I don't think not its anythign wrong with the laptop being from different countries and all)

  Thanks in advance for any help. : D

  I think that the problem lies in your power adapter, which has been purchased with your laptop in Thailand. Asia and Europe use the same standard of electricity (I think?) but it's different in America. If you're lucky your battery may still be usable. You have to buy an adapter designed for America.

• Toshiba NB200-10z - creator.lnk recovery disk is not available

  Hello, I have a problem with my Toshiba NB200-10z netbook, when I run creator of recovery disk Toshiba with that I get the window:

  The unit or the network connection to which the link refers to "creator.lnk recovery disk is not available.
  Make sure that the disk is properly inserted or the network resource is available and try again

  How can I solve this problem?

  You want to create the recovery disk or recovery image stored on USB flash media?

• Power cord for a Toshiba NB200-10Z bought in the United Kingdom EU?

  Hello

  I just ordered the Toshiba NB200-10Z of Amazon.co.uk because the model wasn't available everywhere in Finland, despite being listed on the site of Toshiba Finland. It ' probably be only with the style UK power cord & plug-and - my concern is where can I find a power cord appropriate for the unit (with a schuko type plug)? Or are the UK and different EU cords also at the other end where they plug in the power adapter, which is what I need to get a power adapter and a power cord?

  Thanks for any information.

  Best regards
  Boucicaut

  Hello

  I agree with Al - eX. As you can see on the underside of the adapter AC/DC it can handle voltages range from 110 to 240 volts.

  You need only a new power cord. Therefore, you can contact the service provider authorized in your country. Maybe you can exchange the cable and if you get one free.
  Alternative go to your favorite computer store. Such a cable, you must find there too.

• Toshiba NB200 PLL25A - 00K 002 Netbook (3G modem)

  Hi all

  Firstly, apologies if this information is located in a place, I searched on Google & the Toshiba site with no luck.

  My question is, this modem is in the Toshiba NB200 PLL25A - 00K 002 (3G model) Netbook?

  Specifically what I want to know is if the modem supports the frequencies 3G 850 MHz or 900 MHz.

  In Australia we use that traditional 2100 MHz 3 G in major cities, outside these region there is only Telstra 850 MHz or Optus frequencies of 900 MHz 3 G. This is why I would like to know if it supports either.

  Thank you for your time.

  F3507g being not not 100% sure that it's the F3507g which was delivered in your model, but I believe, is in the European NB200 at least.

  http://www.Ericsson.com/solutions/mobile_broadband_modules/docs/mobile_broadband_module_datasheet_print.PDF

  It is why for WCDMA, which is 3G 850 MHz is supported but not 900 MHz.

• Toshiba NB200 unable to navigate in internet

  Hey everybody,

  I have a Toshiba NB200. I am able to connect to a network (tested on home router as well as prepaid 3G USB modem) and I can ping websites in the BACK. I can not navigate. I tried IE and Firefox, and both have the same results. I tested with the firewall off the coast and still no luck.

  Any suggestions?

  Thanks in advance!

  Hi mate

  Have you checked the two fittings; LAN and WLan?
  If this isn't it!

  If you can ping to the router and if it is possible then you should check if the router is configured correctly I mean that all the data of the ISP (internet service provider) must be checked also.

• Toshiba NB200 monitor resolution vs photo editing software

  Hello

  I think buying a Toshiba NB200. The maximum screen resolution is 1024 x 600. I need a photograph and use Photoshop CS4 or Lightroom 2.5, minimum resolution of 1024 x 800. If I use this program in Toshiba NB200 it will Tween and calculating pixel (re-), right? There is a solution or what photo software do you recommend to use with Toshiba NB200?

  Best regards

  Vasco Neves of the Portugal

  Hello

  I m not a photographer, but perhaps you can use Photoshop on an external monitor where you can choose a higher screen resolution.
  Check this box!

  An alternative, you can use GIMP. AFAIK there is no minimum screen resolution.

• "Invalid serial number" when you install utilities Toshiba NB200-h-13

  This model (h-13) is the student edition sponsored by the Government, used by thousands of Greek students and is not in the support downloads.

  I made a new partition and installed XP Pro SP3, in addition to the standard XP Home. I downloaded all the drivers for the model printed on the label number (PLL25E-00401WMG, which I assume is NB200-122 in the Driver Downloads).

  Most of the important Toshiba Utilities (value of hardware setup, Hotkey, added the logical device) terminate with the error "bad serial number.

  As the Toshiba Utilities work fine in the standard installation (old)

  1. is there a way to bypass the check for the installation of utilities Toshiba serial number?

  2 are there downloads Toshiba NB200-h-13?

  I did some readings from my previous post. It seems that in the 2nd installation of XP the Toshiba utility cannot read the DMI information stored in EEPROM memory, containing the serial number and model of the device. This is demonstrated by the fact that the Diagnostics Toshiba PC utility reports "Unknown" for the standard model, etc.

  As a result, a third question emerges, which is absent from the new installation of XP that allows to read the DMI Info? I guess I should investigate all the services that are running in the original installation of XP, but my bet is that utilities that install these services are not accessible to the public.

  The same utilities install perfectly under Windows 7 (Yes, I did another partition and it installed Windows 7). This means that Win7 has in DMI information tools, or Toshiba 7 installers do not check for her.

  Always in the hope of some clues to the community.

• A few questions from a new owner Toshiba NB200

  Hello
  before 3 days I have buyed a Toshiba NB200 h-13 with Windows XP Home Edition. I want to upgrade to Windows 7 and I have a few questions.

  1) Will Windows 7 run good with Atom N270 1.6 Ghz 1 GB ram and Intel GMA 950 or must I go to 2 GB of ram;

  (2) can I save HARD drive recovery.

  Thanks for your help

  I've been running Windows 7 on my NB205 since the RC, yes it works very well and the drivers are available. I would upgrade to 2 GB of RAM...

  During installation, do not remove the recovery Partition and allows you to return...

  Jeff

• white screen on toshiba nb200, after the entered password

  My toshiba nb200 grandaughters will not respond after the toshiba logo and password promt, when a password the screen becomes blue and black and the cursor flashes in the upper left corner, but nothing else happens, I can use f2 and f12 that will take me to the implementation of utility, but that's all. F8 does not respond so I cannit enter safe mode, the nb is not a dvd/cd player, I tried to remove the battery and the sector taken in turn and replaceing after a wait of more than an hour or more, but not joy. If any body could help, I would be gratefull, my g-daughter would be too.

  Hello

  Do you have a floppy drive?

  If you two options. If you have a floppy drive, you can create boot disks and then start in the recovery console to perform a manual system restore.

  The other option is to attach an external drive and perform a repair of XP installation using a XP install disc.

  Method 1: create the bootable floppy.

  Create bootable diskettes, can be found the article mentioned below:
  http://support.Microsoft.com/kb/310994

  Once you are able to start the computer by using the Setup disk, go to the recovery console and run a manual system restore to restore the computer to an earlier point in time.

  See these articles for help:

  Description of the Windows XP Recovery Console for advanced users:
  http://support.Microsoft.com/kb/314058/FR/

  How to recover from a corrupted registry that prevents Windows XP startup:
  http://support.Microsoft.com/kb/307545

  Method 2: Connect and CD external drive of your laptop and do a repair install using the XP installation disc.

  See this link:

  Perform a repair Installation:
  http://www.Microsoft.com/windowsxp/using/helpandsupport/learnmore/tips/doug92.mspx

  Kind regards
  Afzal Taher-Microsoft Support.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Toshiba NB200-10Z problem with SSD

  Hello friends,

  I have following question,

  I have a Toshiba NB - 200 10z since 2010 and was very pleased with its durability and strength, for the use I've done (the simple navigation, document processing, films etc.)

  Recently, in order to improve its performance I replaced the casting on (5400 RPM) hard drive with a new drive Kingston SSD or 128 GB.

  After that, and with no other hardware changes, the netbook seems to be 100 times slower than before :-(

  Sounds familiar to anyone? What could be the cause for it?

  Thank you in advance!

  Huh... I think you're the first person who reports on the SSD upgrade on this old model of netbook. I have more recent NB520 and always use it with the original HARD drive but use SSD on other machine Satellite.

  What I m missing in your assignment is some info on preinstalled OS. Have you installed recovery original image (OS original version you got with your machine) or your own version of the OS?

  By default the BIOS settings too.

• Toshiba NB200-10Z: after upgrade (for Win7) FN does not work

  Hello
  I'm sorry for my bad English but I'm Italian: I hope you understand me.

  I have a problem with my NB200: I improve my operating system from Win XP to Windows 7.
  So I don't see that FN does not work (in particular, the wireless button!)

  I'm trying to install a lot of drivers (HW installation, Manager wireless), but already I can't use wireless (to connect my netbook online, I use a wired connection!)

  What can I do?

  Thank you very much

  ENCI

  Post edited by: enci

  Edit: ah, I think that VAP does not exist for my netbook (http://it.computers.toshiba-europe.com/innovation/jsp/supportMyProduct.do?service=IT)

  I checked the Toshiba download page, and you are right about VAP.
  Try reinstalling the Flash Cards Support utility.