Grouping of cards NETWORK R710

Similar Questions

• Windows 2008 Core - need a method to configure the grouping of cards NETWORK Broadcom

  Looking for a way to configure the integrated NICs on the broadcom NICs grouping of a PE1950III with Windows 2008 Core of Datacenter edition.

  BACS is a gui tool and will not run on a Windows 2008 Core installation.

  Any way to do it? Is there a command line utility? Documentation on configuration files (so they can be changed)?

  Thank you, Andre.

  
  

• Grouping of cards NETWORK CSACS-1121

  Hello

  Is it possible to configure a NIC team on the 1121 device?

  Kind regards

  Average of Thibault.

  Hi Thibault,

  the second NETWORK adapter on the GBA unit is actually not supported, you will need to connect ACS only using the interface GigabitEthernet0:

  On the installation guide:

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.1/installation/guide/csacs_hw_ins.html#wp1119105

  You can also see that the only interface "in use" is indeed GigabitEthernet0.

  I hope this helps.

  Kind regards

  Federico

  --

  If this answers your question please mark the question as "answered" and write it down, so other users can easily find it.

• The working groups in my network places became inaccessible.

  The working groups in my network places became inaccessible.  I can reach the individual computers if I type the name or IP address, but I can't seem to them through network neighborhood.  Is there a setting somewhere hand who has caused this?  He used to work very well, this has only started happening in the last two weeks.  It began with a single computer not being able to be seen and grew up in the area of network together.

  Any help would be greatly appreciated.

  Thank you

  Mike

  Hi Mike,.

  ·         Did you do changes on the computer before the show?

  ·         You get the error message?

  Follow these methods.

  Method 1: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 2: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 3: Follow the steps in the article.

  How to troubleshoot a network home in Windows XP

  Windows wireless and wired network connection problems

  For reference:

  How to reset the Protocol Internet (TCP/IP)

• Group residential vs network?

  What is the difference between using HomeGroup versus network and what are the advantages/disadvantages of each?
  P.S. I currenty have two computers using Windows 7 and the other using Vista Home Premium.
  The HP VISTA computer will soon get Win 7 HP as well.
  Thank you

  It seems to me that default HomeGroup opens all your libraries (except documents) to other computers in the group.  For example, if your 'Pictures' library includes records 'My images' and 'Public Pictures', these two will be open to all.  You can choose to delete an entire folder, of course, but the default is to expose them to the group.  The network, on the other hand, by default only shows the public folders to the rest of the network.

• My PXE / ESXi autodeploy is unable to see my cards network Broadcom NetXtreme II 10 Gigabit Ethernet (BCM57810).

  My PXE / ESXi autodeploy is unable to see my cards network Broadcom NetXtreme II 10 Gigabit Ethernet (BCM57810).
  

  
  

  What I'm missing here?

  
  

  # Extract the bundle off the downloaded zip line and place it in C:\AutoDeploy

  Add-EsxSoftwareDepot - DepotUrl C:\AutoDeploy-VIBS\BCM-NetXtremeII-11.0-offline_bundle-1553810.zip - net-bnx2x name | Sort descending creationdate | Select creationdate, Version, StatelessReady, summary

  CreationDate Version StatelessReady summary

  ------------                          -------                                                     -------------- -------

  21/01/2014-07:10:23 1.78.79.v50.2 - true 1OEM.500.0.0.472560 bnx2x: driver for VMware ESX

  08-02-2012 03:00:42 1.61.15.v50.3 - 1vmw.510.0.0.799733 true bnx2x: driver for VMware ESX

  # Add the driver (use force because complains and fails otherwise)

  Add-EsxSoftwarePackage - ImageProfile "Profile001" - SoftwarePackage net-bnx2x-force

  # Check it is there

  Get-EsxImageProfile "Profile001" | Select viblist - ExpandProperty | where {$_.} Name - like "net-bnx2x"} | FT-auto

  Date created Version of the vendor name

  ----      -------                           ------   -------------

  Broadcom 1.78.79.v50.2 - 1OEM.500.0.0.472560 net-bnx2x 21/01/2014 07:10:23

  # Export

  Export-EsxImageProfile - ImageProfile "Profile001" - ExportToBundle - FilePath "C:\Users\Administrator\Desktop\ESX-Software-Depot\Profile001.zip".

  WARNING: The image profile is not validated.  ISO / offline Bundle will always be generated, but may contain errors and may

  functional.  Errors:

  WARNING: Requires the VIB Broadcom_bootbank_net - bnx2x_1.78.79.v50.2 - 1OEM.500.0.0.472560 com.broadcom.cnic_register - 9.2.0.0, but

  be satisfied within the ImageProfile. However, the VIb (s) Broadcom_bootbank_misc-cnic - register_1.78.75.v50.1 - 1OEM.500.

  can meet this requirement.

  > # Confirm ESXi image name

  > Get - EsxImageProfile - name Profile001 | ft - auto

  Vendor name has changed the level of acceptance

  ----       ------ -------------        ----------------

  VMware Profile001 27/02/2014 PartnerSupported 18:44:45

  >

  > # Net-bnx2x Confirm is a software installed

  >  Get-EsxImageProfile "Profile001" | Select viblist - ExpandProperty | where {$_.} Name - like "net-bnx2x"} | FT-auto

  Date created Version of the vendor name

  ----      -------                           ------   -------------

  Broadcom 1.78.79.v50.2 - 1OEM.500.0.0.472560 net-bnx2x 21/01/2014 07:10:23

  >

  > # Confirm the current rule of deployment deploys profile001

  > Get-DeployRule-name *

  Name: DefaultBoot

  PatternList:

  ItemList: {Profile001, cell01}

  If you put all the VIB - names in a single order, separated by commas, then it works fine

  Add-EsxSoftwarePackage - ImageProfile - misc-cnic-register,net-cnic,net-bnx2x,scsi-bnx2i,net-bnx2 SoftwarePackage

• The last user to join a group of the network will have the peerID above?

  I thought a lot about how whether someone is the first user in a network group. Specifically, I was wondering if I could use the NEXT_DECREASING Mode send to see if someone had joined before a user. Michael Thornburgh said "the peerID persists for the duration of the connected NetConnection.  "as soon as he logs off, the peerID is destroyed and is never reused." That makes me hope that if a user leaves a mesh and joined to another, they would not get the same peerID. However, he also says that the peerIDs have a 'Pseudo-aléatoire' element in their generation, what makes me despair that she would follow a growing model. So to the heart of it: the last user to join a group of the network will have the peerID above?

  lol peer IDs are cryptographically pseudorandom and distributed between 0000000000000000000000000000000000000000000000000000000000000000 and ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff.

• Only 4 cards network

  Most of our servers have 6 + NIC...  Usually, two for the management/Vmotion, two for virtual machines, two for the NFS storage.

  Our newest blades only have 4 network cards... Although they are all 10 GB.  ESXi 5.0 currently using

  What is the best way to implement?   Here are the two choices I think about: different VLAN for all which, incidentally.

  (1) create a switch with all physical cards four joints, 3 vmks (1 for management, 1 for vmotion, 1 for nfs).  All 4 physical network adapters be active for all and that the ESXi to understand.

  (2) create a switch with all physical cards four attached, 3 vmks again.  But organize the consolidation and failover of the physical NIC for each vmk separately.  Management and vmotion say gets vmnic0 as active, with vmnic3 as secondary... then nfs gets vmnic1 and vmnic3 as active. And virtual machines get vmnic2 as active, with vmnic1 as before.

  #2 type of private VM traffic however... Should I leave VMs and NFS share all the vmnic1-3?

  #3 create a switch with all physical adapters connected four, 3 vmks again. Management and vmotion gets vmnic0 as being active, with vmnic3 as secondary... then nfs and VMs to vmnic1, vmnic2 and vmnic3 as active.

  Thoughts?

  You have different physical switches for management/vMotion, NFS and VM traffic or they are all connected to the same set of physical switches? This can strongly influece the answer on these questions.

  You have company + license and allows to use distributed vSwitches?

  If so, control network IO and focus on the burden of reunification are certainly considerations that could make your life a lot easier. With these two functions, you can go in confidence with the unique vSwitch parameter and all 4 uplinks, leaving basic teaming load dynamically determine where to place the VM vNIC and vmkernel ports while ensuring overall fair through the NIOC.

  If you have not undertaken + licenses and need to go with standard vSwitches, I would probably build a vSwitch with two uplinks to the management/vMotion and NFS, using alternating rising favorite for both. Then another vSwitch for traffic from the virtual machine to the other two uplinks.

  (2) create a switch with all physical cards four attached, 3 vmks again.  But organize the consolidation and failover of the physical NIC for each vmk separately.  Management and vmotion say gets vmnic0 as active, with vmnic3 as secondary... then nfs gets vmnic1 and vmnic3 as active. And virtual machines get vmnic2 as active, with vmnic1 as before.
  #2 type of private VM traffic however... Should I leave VMs and NFS share all the vmnic1-3?

  This example is not really make sense to me because you only have a single interface for NFS vmkernel. Assigning two physical NIC as active for this vmk is practically useless in this case. Is less than then you use IP-hash channeling on the vSwitch, in which case you should not all NIC expectations for any group of ports on the vSwitch together still.

  Apart from this, even a simple but dedicated 10 GB NIC for VM traffic provides a lot of bandwidth.

  Is Multi-NIC vMotion a desired in your scenario use case too or you want to just go with a vMotion NIC?

  On that note, I don't really know your environment and requirements, but two 10 GB interfaces really offer a lot of bandwidth, and I mean a lot. Four 10 GB interfaces can seem a bit of an overdose, especially if you can ensure fairness through the NIOC and do not necessarily need to worry about custom configurations of active / standby NIC.

• Error of grouping of HP network adapters

  After conversion of 2 HP DL360 G5 with NIC team I now get the error when you try to launch the below HP Network Configuration utility:

  "An error has occurred due to invalid data in the xml file that is used by this application.  The XML file has been damaged and needs to be reinstalled from the installation media.

  This has happened on both servers, up to now, I converted and although the lack of consolidation of network cards is not a huge problem, I fear that this is a code that do not have the conversion process a sweetness that it appeared and there may be more corrupted files hidden.

  Anyone know if there is a known issue?

  I am using Stand Alone Converter 4.3

  Thank you very much

  Hello

  Hello from the Canada

  After the P2V conversion, you MUST remove all agents of the material of the Virtual Machine that includes the consolidation of NIC from HP, it will not work properly

  on your VM and it can cause a lot of weird problems

  As you can see on this Ko under the section of "Tasks to perform after that conversion is complete" http://kb.vmware.com/kb/1004588

  Tasks to perform after that conversion is complete

  After the conversion is completed:

  1. Check the settings of virtual hardware:

     • Adjust the number of virtual network adapters. If you need customize the host name or IP address, leave all network cards present but disconnected.
     • Remove all devices useless such as USB controllers (if you are running on ESX), COM ports, or floppy drive

  2. Start the virtual machine Mode without failure. For more information, see start a guest operating system Windows in SafeMode (1004011).
  3. Click on Start > Control Panel > Add / Remove Programs.  Remove all unnecessary programs used to install or support device, drivers such a RAID, network software of grouping or management, software management of wireless card management tools and drivers audio and video. Do not restart if you are prompted by an uninstall program.
  4. Restart the virtual machine in Normal mode.
  5. Remove additional devices or device drivers that have been used in support of hardware on the physical server. Use the Device Manager or control panel, depending on the version of Windows to remove unnecessary devices. It may also be necessary to view the event log to clear the messages failed rest device startup.
  6. VMware recommends changing the HAL in the uniprocessor virtual machine if the source server is configured with an abstraction layer multi-CPU hardware (HAL), and the destination virtual machine is configured to use a single processor. For more information, see modification of the Abstraction Layer HAL for a Windows virtual machine (1003978).
  7. Install VMware Tools and reboot if you are prompted.
  8. If necessary, customize the identity of the virtual machine. VMware recommends using the Microsoft Sysprep utility to achieve this, however, it can also be achieved by manually changing the host name, IP address, and any other record of unique identification. For more information, see How to use Sysprep: An Introduction http://technet.microsoft.com/en-us/library/bb457073.aspx.
  9. If the System Configuration Utility (msconfig) has been used before the conversion, select Normal startup switch to return to a normal boot configuration. For more information, see using the Windows System Configuration utility (1004010).
  10. Apply any previously deleted static parameters IP address, as requires it.
  11. Reconnect any disconnected NIC virtual, as required.

• VMWare & connectivity card NETWORK DMZ

  Hello

  Running VMware ESX Server 3.5.0, which currently has two nic is installed.

  One is used for the service console and the second is used for the existing network of the virtual machine.

  I now need to build a new virtual server as a mail relay that will be patched in our DMZ.

  As none of the existing server are corrected in the DMZ will I need to purchase and install a new network adapter to be corrected in the DMZ and then configure the new server to use the DMZ NIC jst?

  Thanks in advance for any response.

  The prices your DMZ your LAN regularly on the same physical switches or different physical switches?  If they are different physical switches, then Yes you must buy a new network card.  If they are on the same switch, separated only by VLAN, you can configure technically on the switch port that the virtual machine is connected as a trunk port, then separate the virtual machine by creating groups of ports on the virtual switch and assigning the tag VLAN corresponding to the correct port group.  IE if your public network is VLAN10, then you EF tag VLAN 10 for the Group of existing ports.  Then you would create a new "virtual switch" but assign it to the already existing virtual switch, name it DMZ and under the id VLAN give him the other number VLAN, that is to say 11 or whatever it would be.

• Cannot install Wireless Adapter (card NETWORK or USB key) to the Pavilion p6340a Win 7 Home Prem

  I removed a work card TP-Link to a Pavilion a1300a XP Home PC network to put in my Pavilion p6340a Win 7 (64-bit) Home Prem PC.

  Download and install the current drivers of TP-Link.
  Installed everything well and the adapter can be seen in sub "Change adapter settings" in network and sharing Center and shows as working properly in Device Manager, but it is not recognized as a network within the network and sharing Center.

  Under "Manage wireless networks'" nothing appears, if I then click on Add"then manually create network profile" "I then get an informative message '" an unexpected error occurred'. "

  Suspect a problem with the NETWORK card, I uninstalled it and its drivers and tried to install a USB wireless adapter with the same exact result and the error message. It seems that there must be an OS problem or something stopping the wireless to work. USB adapter both NIC work properly when installed on the former Pavilion a1300a XP Home PC. NETWORK card and USB adapter are the current drivers for Win7.

  All the ideas it driving me crazy. A simple 5 minutes on any other PC task turned into many.many hours without solution.

  After many hours of uninstall re install & try everything under the Sun in many forums, I finally found a solution. Despite trying with firewall disabled at different times was the final fix

  1. Uninstall NETWORK card and USB drivers and devices.
  2. Then uninstall the AntiVirus (in this case AVG Internet Security)
  3. Reinstall the NETWORK card and drivers
  4. Reinstall AntiVirus

  Tried the USB adapter as well so that the antivirus has been uninstalled and installed no. with problems.

  Everything works very well.

• Can someone point out the card network for Satellite Pro C850 driver?

  Hey, I have re installed Windows 7, but I forgot to download the drivers. I needed before hand. I can t have access to the internet on this subject to update the drivers. If someone could please please find the network drivers for the Toshiba Satellite Pro C850 cards and post them here!

  I don't want to download a driver manager. Just the drivers please!

  To help we need more information. You use Win7 32 bit or 64 bit and what model of laptop you have exactly?

  Anyway, if you can access the internet with another PC you can find drivers on http://www.toshiba.eu/innovation/download_drivers_bios.jsp

  Check it out.

• Satellite Pro 2100: card network wireless not recognized after upgrade

  I have a Satellite Pro 2100 ad I used successfully a PCIMCIA 802. 11b card wifi for two years.

  Studying the manual, I discovered that the notebook is "wifi ready" (it has a wifi switch, a switch wifi of Alt - F8, and a section of the manual).

  I opened a Bay and found out a mini-pci slot. That's why I bought an Intel 2200 BG wireless adapter and I put it inside, which connects the sons of two antennas, located in the Bay. Finally, I was ready to son mask 11 and 13, as suggested in many forums. But when I put the card inside, unknown electrically. It seems that the mini-pci slot must be Electric.toutes impossible. My Bios is not impossible, but it.

  In another Bay close to the mini-pci card, I discovered an empty shell for a chip. Is this an impossible chip?

  Hello

  As far as I know that this unit is about 4 years old and at that time the unit is tested with the wireless network card with the PA3212U-1MPC part number. This map has been tested, is also compatible and can be used.

  I put t know what is going on exactly in your case, but new material should be recognized and the driver must be installed. I put t know what you mean exactly, but can you please explain exactly the situation?

  The card is correctly recognized and installed in the Device Manager?
  You can use FN + F8 key combination to activate the wireless card?

• Pavilion G7-1355dx: card network problem

  Hello

  I had previously posted the question below and took the lead on mark as resolved. The answer I got was good, but because of many different configurations of my model of my laptop model, it was not correct for mine.

  I have an old HP Pavilion 1355dx G7 and I use it during the games XBOX a stream. It has only one network adapter Wireless 2.4 ghz, if coupled with that much congestion in my neighborhood, it broadcasts only during the flawless. New info: my laptop has an AMD processor, not an Intel processor.

  This laptop does support 5 GHz wirelesss network cards compatible with AMD? I am hoping to move to a 5 ghz however I want to make sure that it supports and is on the white list before I buy one.

  Thanks for the info. That's what I was afraid of. Can be an excuse to get a new laptop and let the kids use it. It is not a big deal, for the most part, it works well, but you can see in sensitive applications.
  
  I used an app WiFi Analyzer and each channel is overused. I'm surrounded by more than a dozen networks (tons of apartments) and use channel 11 that is congested, but less crowded than 1 and 6.

• card network said authentication attempt

  My wireless card is up to date and I have an acer with windows 7 home prem and im wondering how can I go about fixing the adapter... troubleshooting does not work all it says is that my network adapter does not work correctly or my access point. Another computer on my network can connect perfectly well and has no problem... ive tried everything please help

  Hello

  Assuming that wireless router is configured correctly, it is a signal and the wireless card on the computer is physically in.

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  To ensure that if there is Wireless Utility a seller is not running with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd AV/Firewall/security software part, s costume keep blocking aspects of Local traffic even it they are off (disabled).

  If possible set up the firewall correctly, /Security costume otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.