Guest WIFI Linksys WRT54GS by connecting (v6) to ActionTec (verizon fios)...

Similar Questions

• I have a SBS 2011 and cannot connect to internet through VERIZON FIOS.

  I have a SBS 2011 and cannot connect to internet through VERIZON FIOS. The SBS is unable to detect the IP address and gave an error message. I never get to a screen that allows me to type in the "IP address of the router" or "IP address". Verizon told me that their router address is "192.168.1.1". After a new trial, I added my NETGEAR FS105 switch between the FIOS router and my PC 2 and SBS. Result - conflict of addresses of servers.
  Any suggestions or solutions to this problem?

  Thank you
  Chuck

  Hi Chuck

  Your question is addressed in the Microsoft Answers forums.

  Please ask your question in the following forum.

  Small Business Server Forum:

  http://social.technet.Microsoft.com/forums/en-us/smallbusinessserver/threads

  Concerning

• How to get the IP address Linksys WRT54GS DHCP assigns to a Wi - Fi connection?

  To connect the Linksys WRT54GS to a demonstration of Microchip DV102411 WiFi Comm card I need the IP address assigned by DHCP. The Administration WRT54GS log is enabled, but there is no incoming or outgoing network activity. The DV102411 can see the SSID linsys scanning for wireless networks and attached to it but once attached, I need to know the address IP of the DV102411 has been given by the WRT54GS.

  You can consult the router DHCP client table.

• Wrt54g Linksys Wireless Router - connected but not display page

  Halo!

  I have a Linksys WRT54G wireless router - I was able to connect to the wireless connection, but there is no display of the page in the browser.

  What seems to be the problem here?

  TIA,

  wilardboi

  Please reset the router and reconfigure:

  1. hold the reset for 30 seconds button.
  2. then disconnect the Dungeon can now hold the reset button for
  another 30 seconds.
  3. plug back in the power and keep the reset button pressed
  for 30 seconds.
  4. release the reset button.

  Open the configuration of router with 192.168.1.1 page... White-username and password: admin

  To configure the wireless router.
  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here the wireless network mode must be mixed
  -Provide any name in the name box of the wireless network (SSID), while
  without space between the two cases.
  -11 wireless channel
  - And wireless SSID broadcast should be enabled and then click

  Save
  Parameters.
  Please take note of the name of the wireless network (SSID) because it is the '
  Network identifier.
  For wireless security: -.
  Now click the sub-tab under wireless > wireless security.
  Change the mode of WEP wireless security
  Encryption must be 64-bit.
  Let the empty password, do not type in anything whatsoever.
  And under type WEP Key 1 in all 10 digits please. Click Save
  Parameters.
  Please note the 1 WEP key as it comes to the security key for the
  Wireless network.

• Linksys WRT54GS Help - Bricked itself?

  Hello community,

  I recently inherited a router Linksys WRT54GS my boyfriend hasn't needed. I kept it in storage for about 6 months because I didn't really need, but yesterday, I found that lying around and decided to go ahead and plug it in, to see if I could use it as a switch to connect my computer, Xbox and PS3. So I plug it into the wall... And it seems dead. All of the lights on the front panel are turned off. On a whim, I decided to plug it into my computer, wired and test pings. I kept getting the "Network unreachable" error, and the router was not network. However, the light on the front corresponding to the numbers 1-4 port back lit up when I plugged my computer at each port. There is no reset anything else, even after a 30-30-30. Should what steps I take now?

  It is possible that the router no longer works. Have you tried to use the router when your friend gave you? If you are still not able to ping the router using its IP address standard, try setting static IP on your computer using 192.168.1.50 for the IP address and 192.168.1.1 for the default gateway. Once the IP static value, try to ping the router command and access the router page using 192.168.1.1.

• How to remove several networks in the Smart WiFi Linksys

  I hope this is the right place to ask this question, if not please me foregive. I recently replaced my router with a WRT1900AC and after installation, I use my account for smart wifi Linksys to the Manager of this router that I used with my old Linksys router. However, when I noticed two other networks listed as to connect to networks of connection. They do not connect what either and I think that they are of my old router (I used the same network name). How do I remove these? They do not seem to be causing the problems, but are confused. Thanks in advance for any help!

  Ken

  Hello! Articles on the following link will help you remove the existing networks on your computers, portable devices or game consoles: http://www.linksys.com/us/search?text=remove%20networks&type=support_faqs

• Cannot access wireless with linksys WRT54GS router

  Hello

  I just installed a Linksys WRT54GS router on my connection, the problem I have is to be able to access with my wireless on my laptop.

  I kept getting a message saying 'connection unindentified' 'access '. I did most of what is already on your forum that such a power out of my rooter, my modem and such and still nothing. I am able to access wireless with my girlfriend Mac laptop, my playstation 3 and my desktop computer which uses Windows X. I initially thought that it my be a problem with my security but even when the connection is unprotected I still have this error. I am trying to disable the IpV6but that didn't ' dot something or the other.

  My laptop is a Toshiba Qosmio X 300 PQX32C-033019 with Vista and my router is a Linksys WRT54GS to. 6

  Here is my connection connect you, sorry if this is in French:

  Try this-

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER...
  Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the Standard channel to 11-2, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and no mailbox for example: your 10-digit phone number) and click on save settings...
  Please note the 1 WEP key as it comes to the security key for the wireless network...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...

  On your Vista laptop, first turn off the wireless network connection and restart the laptop, and then enable the wireless connection...

  Then click Start > Control Panel > Network and Sharing Center > manage wireless network and click Add, select manually create a network profile and click Next, enter the name of your network SSID/network, select WEP for security type and enter your 10-digit network key and click Next, it should say 'Connected successfully to _' close all windows , and then restart the laptop, now see if you can connect to the Internet wireless...

• Question to Linksys WRT54G password

  I have a router wireless of linksys WRT54G hard wired to a mac and I use the router to get your laptop online. Everything works beautifully. Now I have an iphone that I want to be able to use the same network on. When I turn on my iphone it finds the router which of course requires a password. I'm going in what I think is the password and it is denied. I am able to connect to the Web page of the router and access all my settings. On the administration tab, there is a place to change the password. I changed this and entered a new password, but the only thing that changes is the password that is used to get access to the web page of Linksys. (the web page that I can enter to change and access settings) am I wrong to think this would be the same password to my iphone application?

  Sorry for the long explanation, just try to give detailed information.

  Thanks in advance.

  Yes, it's the wrong password.  Look under your security settings wireless / wireless and you will find the password requested.  This will be a key/paraphrase or password depending on the encryption you put in place.

• Assistance using Windows using Linksys WRT54G wireless remote

  Please someone help me. I have Qwest DSL service, ActionTec Gt701R and Linksys WRT54G - Version 6.

  If I connect directly to the Modem, send a request for Assistance from a distance, the Expert can connect to me without any problems. Here is the IP ticket RA information-

  RCTICKET = "65538,1,71.215.174.28:38861;192.168.0.2:3389; trippc:3389, *.

  When I'm connected wireless using the WRT54G, send a request for Assistance from a distance, the Expert cannot connect to me with an error that the DNS cannot resolve the host name. I assigned a static IP address to my laptop and the Port 3389 to sent to this IP address, according to the Linksys support. She is the information the RA ticket IP for failure.

  RCTICKET = "65538,1,192.168.0.4:1293;10.10.10.50:3389; trippc:3389, *.

  The IP address in this post are internal addresses, the Expert cannot find them on the Internet.

  Anyone have this working? If you have, please send the instructions step by step that followed you.

  Thanks in advance for your help.

  Problem solved on the Forum of Qwest. The modem must be changed to use "a transparent bridging. The the WRT54G must be changed from automatic DHCP to PPPoE.

  Public static IP and Port Forwarding have nothing to do with this issue.

  Thanks for your help.

• Wireless router to modem Homeportal 1800 HG 2wire Linksys WRT54G with questions

  I have the Linksys WRT54G, and I'm trying to use it as the router to my modem 2wire Homeportal 1800 HG wireless.  The 2wire has four ethernet Sockets in the back marked from 1 to 4 and a telephone jack to connect to the wall for AT & T DSL service.

  I have the phone jack connected, and:

  -an ethernet cable

  -to one of the sockets at the back of the 2wire ethernet

  -to the 'Internet' on the Linksys ethernet jack

  - and an ethernet cable

  -to one of the ethernet (1-4) at the back of the linksys

  -to the ethernet port on the computer

  The Linksys is unable to connect via the modem and reports that it may not get an IP address from the PPPoE server.  (Directly connect to the 2wire works well though.)

  Who am I wrong configuration?

  There is no side effect of bridge mode... It is one of the mode in which the modem function. When the modem is in bridge mode, you cannot go online with the computer connected directly to the modem... and you will get a 169.254.x.x ip address.

  So after you convert the modem into bridge mode, you must do the PPPoE settings on the router to go online via router.

• My wifi network does not connect automatically

  Hi all

  im a user frustrated.

  My wifi network does not connect automatically, keeps asking me the password (even if I continue to score for remembering network). The password does not change.

  I also deleted the list of networks do not forget and do it again. Any help?

  Much appreciated guys.

  

  create another user account and start to this account, set up a wi - fi connection and restart to this account.

  Is the same behavior?

• problem with express mini pci wireless lan card. I can't connect to internet via wifi but I can connect to the internet via cable.

  Hello! I have a problem with my card express 11 b/g/n wireless lan mini pci because I can't connect to internet via wifi but I can connect to the internet via cable. whenever I try to connect it repeat to myself that there is a problem with your wireless network card. I tried troubleshooting, uninstall and reinstall the program, but always the same result. I'm updating too but still the same thing. I use a windows 7 Professional on my Lenovo 412. can someone help me? Thank you!

  Hello

  Method 1: I suggest you to follow the instructions of the link to solve the problem of network card:

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-fix-network-adapter-problems

  Method 2: Troubleshoot wired and wireless in Windows network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Reference: http://forums.lenovo.com/t5/R-and-L-Series-ThinkPad-Laptops/L412-Wireless-Automatically-Disables/td-p/264447

  You can also post your question in the forum of Lenovo to get help:

  http://forums.Lenovo.com/

• XP key wep changes for new router linksys after the connection. you need to reinstall the WEP every time you start from the top.

  XP key wep changes for new router linksys after the connection. you need to reinstall the WEP every time you start from the top.

  Hello

  Let us perform the steps below and check out them.

  a. click "Start," "Control Panel", then "Add or Remove Programs". In the box "Currently installed programs", find the name of your wireless router. Click on the name of the software, and then click 'remove '. Click 'Yes' when prompted to confirm.
  b. click "Start" then "run". Type "Services.msc" and click "OK". Select 'Wireless Zero Configuration'. Click on 'start '.
  c. click 'Action', 'properties '. In the drop-down menu "Startup Type", click on the arrow and select 'Automatic' to assign the commissioning of automatic Wireless Auto Configuration. Click on 'OK '.
  d. restart your computer.
  e. right click on "Wireless connections" icon Select "View available wireless connections." Click on "change the order of preferred networks. Select the name of your network, and then click "Properties". Erase the old key and enter a new. Click the checkbox next to "Automatically use that key." Click on 'OK '.

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Linksys E4200 and connectivity Motorola SBG6580

  Here is a picture of my home network. The problem I'm having is, I can't get the WD MyBook Live Duo to be seen on the entire network. If it is connected to the Linksys, all computers connected to the Linksys can see it, but not those related to the Motorola. If I put it on the Motorola, the same thing happens, but in the visa versa. I bought the Motorola for its DOCSIS 3 capabilities, not for the wireless. I prefer to use the Linksys Wireless. Any help would be greatly appreciated.

  

  Devices must be on the same subnet (e.g. 192.168.1.x) to be able to see each other. You could make the Sb IP 192.168.1.1 and 192.168.1.2 for the E4200 and connect a cable from LAN of the SB E4200 (not WAN) port lan port.

  Here is a guide if you need: http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=3733

• How LinkSys WRT54G v7 supports RTSP streaming service?

  Hello

  I use the LinkSys WRT54G v7 and I can see the RTSP videos using VLC player to m.youtube.com. Strangely, I can't play videos if another AP as the DLINK is used instead of LinkSys.

  I analyzed packages and discovered that RTSP server (youtube) sends RTP packets to the ports of the client which are acquired to the RTSP SETUP procedures. Then the Server packets cannot reach the customer because the hole of the UDP is not perforated to the AP.

  But, when I use the LinkSys, RTP packets can cross the NAT.

  That is my question. LinkSys offers NAT traversal for RTSP streaming service? So, why can't find a list of features on this subject from the LinkSys product information? No explanation for this?

  Thank you in advance for your help!

  1. None of the NAT helpers in the Linksys firmware are documented anywhere.

  2. If possible, they added a helper for RTP.

  3. it could also be that VLC player in front of the port with UPnP.