have to hit the router works for a connection

Since I'm router not all wireless connections in the office laptops and Xbox fine except for an old laptop to connect, I have to hit the router and the

Hello

Look for the updates driver WiFi (wireless) of the computer with the system manufacturer
If integrated and, if the device manufacturer a separate device.

Also check the website of the manufacturer of the router for firmware updates.

Is this computer located at a distance from the router or are there obstacles on the way?
Try to close the laptop as a test - but not too close, usually 6' away or almost.

I hope this helps.

Tags: Windows

Similar Questions

  • MN - 700 router worked for a while (over 3 years) without password. How to set a password? __

    MN - 700 router worked for a while (over 3 years) without password. How to set a password?

    MN - 700 router worked for a while (over 3 years) without password. How to set a password?

    This is a pretty old router, but documentation is still available from Microsoft:http://support.microsoft.com/kb/902461 the 'Guide' is more complete, but the "Base Station Configuration Guide" will explain how to configure the router.

    I guess what you mean by a "password" is the password for the wireless encryption (there is also a password that controls access to the router configuration utility). The following are the basic steps to configure wireless encryption (see the documentation for more details and screenshots):

    1. utility access to the router configuration, preferably with a computer connected to the router with an Ethernet cable (if you change your wireless security, the parameters using a computer connected to the router by wireless, the connection will be abandoned as soon as you click APPLY).  Open a web browser and type 192.168.2.1 in the browser address box.  If you have not changed the logon password, enter 'admin' (without the quotes, all lowercase).

    2. click on the "Security" link on the home page of the configuration tool, then "Wireless Security".

    3. Select the "niveau_chiffrement" in the combo box to "256-bit WPA - PSK (louder)" - unless all of your wireless devices are so old they don't support WEP (unusual for a wifi device years less than 5 or 6).

    4. in the box, type a password (between 8 and 63 characters), and then click 'apply '. at this point, you will be disconnected from the router (and the Internet) If you did the above changes using a computer connected to the router WiFi.   Write the password in a place where you don't forget.

    5. close router configuration utility.

    To set up your wireless computers:

    6. open network connections (start > run > ncpa.cpl > OK)

    7. right click on your wireless adapter icon and select Properties.

    8. click on the wireless networks tab

    9. make sure the box at the top next to "use Windows to configure my wireless."

    10. in the list of "Preferred networks", select the entry to your router (your network name), click on 'delete '.  [This deletes the entry from your wireless network WITHOUT a password, so that you will be able to add an entry for a network with the same name WITH a password.]

    11. click on the view wireless networks"" button.

    12. the name of your network should appear in the list of wireless networks.  Select it and click "connect". When you are prompted for the password, enter the WPA password set in the router configuration.

    13. open a web browser and confirm that you can access the Internet.

  • How can I make the individual work for each song on a compilation album of show when I browse my playlists?

    I get a lot of my music from Soundcloud where individual songs are released by artists often with none of the albums.

    So, when you add these songs on iTunes I the name of the album for each of them SoundCloud despite the fact that each of them have different names track/artists/works of art.  When I select the option to indicate that the song is part of a compilation album, even if the individual work remains in each song and shows when I play the song, looking at my playlists, songs from my compilation album of SoundCloud will only show album art compilation rather than the individual works for each song.  How can I my iTunes will show that each individual work?

    You can't while retaining spacing as part of this same album. If you want each art individual to show then tracks them to a unique combination of the album title and album artist. If the tracks are underway on an older iPod then the tracks on the album must be unique.

    TT2

  • users cannot save .pdf, .doc files using "Save target as" in google search results. Can someone help me, I couldn't have known that the same works very well on some computers.

    I am the Director of technical support for more than 1000 computers. Recently in some computers (windows based) users cannot save .pdf, .doc files using "Save target as" in google search results. Can someone help me, I couldn't have known that the same works very well on some computers.

    Hi MASPAdministrator,

    Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows XP forum.

    http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

  • I'm unable to access my computer (windows 8) with my microsoft account. The password works for the connection to outlook on the internet, but not the computer.

    Original title: connection problem

    I'm unable to access my computer (windows 8) with my microsoft account. The password works for the connection to outlook on the internet, but not the computer.

    The message I get when trying to connect is simply that I cannot connect you at this time and that I should follow a link to reset the password - what I've done without result. The computer is connected to the internet.

    Hello

    Thanks for posting your query on the Microsoft Community.

    With the publication of the description, I understand that you are unable to access your computer using Microsoft password account on the machine Windows 8. I will certainly help you get this problem.

    I would be grateful if you could help me with more information:

    1. Since when you are facing this problem?

    2. What is the exact error you receive by accessing the computer?

    I would say to you follow the suggestions provided by Cliff_N responded on 7 December 2012 in the below thread Microsoft:

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-security/why-cant-i-sign-into-Windows-8-with-my-Microsoft/7662ea57-c321-4bfe-84e9-fc9ebb87a44b?TM=1355519512755#_self

    Important information: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

    Note: When updating, the applications you have installed Web sites and DVDS is deleted. The applications provided with your PC and applications that you have installed in the Windows store will be resettled. Windows puts a list of apps removed on your desktop after you refresh your PC.

    For more information, you can consult the Microsoft article.

    What to do if you forget your Windows password

    http://Windows.Microsoft.com/en-us/Windows/what-do-forget-Windows-password#1TC=Windows-8

    Hope this information is useful. Please come back to write to us if you need more help, we will be happy to help you.

  • I have Windows Server 2008 R2. I have set up the desktop remotely for 5 users, but each time a user logged on to the other user will be disconnected.

    issue license remote dekstop

    I have Windows Server 2008 R2. I have set up the desktop remotely for 5 users, but each time a user logged on to the other user will be disconnected. Is this a problem with the license? Is it how do I get license for 10 users remote desktop? Thank you

    You will get the best answers by posting in the dedicated remote desktop on TechNet Forum:

    Remote Desktop Forum services (Terminal Services)

  • Hi, I have been on the monthly plan for illustrator and photoshop, but felt that it would be cheaper to just buy these programs instead of paying every month. I don't see this option

    Hi, I have been on the monthly plan for illustrator and photoshop, but felt that it would be cheaper to just buy these programs instead of paying every month. I don't see this option

    There is no option to buy the latest versions of the software. Creative cloud is only available as an ongoing subscription.

    However, you can always buy CS6 software if you wish.

    Please see: CS6 product purchase

    Guinot

  • Need help to understand why my downloaded PDF doc displays "Please wait...". If this message is not finally replaced with the appropriate content... "after that I have already downloaded the version update for windows 10

    Need help to understand why my downloaded PDF doc displays "Please wait...". If this message is not finally replaced with the appropriate content... "after that I have already downloaded the version update for windows 10

    This is because the PDF file is not be open in Acrobat or Reader, but by the browser which is unable to handle the specific PDF content.

    If you use Firefox or Chrome, follow these steps: https://helpx.adobe.com/livecycle/kb/xfa-forms-firefox-chrome.html

  • I can connect to the router but no internet connect windows 8

    I took each of boredom that my NEW HP envy provides however I still get a no internet connect error.  If I reset my router and checked that it is acceptable.  I can reset everything and internet will work for no more than 30 sec. I know that the internet is able to work as I plugged the ethernet cable, but I want it is wireless! What to do next! ?? !!

    Hello

    Check with HP Support, their online documentation and drivers, diagnostics,
    and ask questions in the forums about known problems.

    Support HP & drivers
    http://welcome.HP.com/country/us/en/support.html

    Contact HP
    http://welcome.HP.com/country/us/en/contact_us.html

    HP forums
    http://h30434.www3.HP.com/PSG/

    ===============================================

    Note the use of Win Key + X and Win Key + W (to access control panel, run,
    and settings according to needs). Win + D key calls to the office and use
    Win Key activates / deactivates the desktop and start screen.

    --------------------------------------------------------------

    Control Panel - Network and sharing Center - solve problems

    References to Vista also apply to Windows 7 and Windows 8.

    Your router be guess here, you have successfully updated the firmware a possible
    solution? And I would update your WiFi drivers on computers. How far away are they
    you have set in the router? Are there obstacles in the path?

    Actually try updating your driver and disabling the network logon.

    Control Panel - network - write down of the brand and the model of the Wifi - double click
    top - tab of the driver - write version - click on update driver (can't do
    nothing that MS is far behind the certification of drivers). Then right click on the Wifi
    Device and UNINSTALL - Reboot - it will refresh the driver stack.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    Microsoft - How can Windows 8 - I fix the network adapter problems? (Do not forget to see
    This section-> update the NIC driver).
    http://Windows.Microsoft.com/en-us/Windows-8/fix-network-adapter-problems

    Drivers and Microsoft - Windows 8 - Hardware
    http://Windows.Microsoft.com/en-us/Windows/hardware-drivers-help#hardware-drivers-help=Windows-8

    Microsoft - Windows 8 - why Windows is not find my device?
    http://Windows.Microsoft.com/en-us/Windows-8/why-isn ' t-windows-conclusion-device

    Microsoft - Windows 8 - what happens if a device is not installed correctly
    http://Windows.Microsoft.com/en-us/Windows-8/what-device-isn ' t-installed-correctly

    Download - SAVE - go where you put it - right click – RUN AS ADMIN.

    You can download several at once however restart after the installation of each of them.

    After watching the system Maker you can see the same device manufacturer
    more recent versions. (Those become your fonts of rescue system manufacturer).

    Repeat for network (NIC) card and is a good time to get the other update
    Drivers Windows 8 like updated drivers.

    ------------------------------------------------------

    Make sure you know the details of connection to your wireless router - SSID and password.

    You lose connection when you do and have to redo your logon.

    Control Panel - Network & Sharing Center - set up a new connection or network

    -----------------------------------------------------

    And:

    TechingItEasy - how to join a Wi - Fi network in Windows 8 by MVP Andre Da Costa
    http://techingiteasy.WordPress.com/2012/06/09/how-to-join-a-Wi-Fi-network-in-Windows-8/

    Microsoft - Windows 8 - Web & Networking
    http://Windows.Microsoft.com/en-us/Windows/Web-networking-help#V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1&Web-networking-help=Windows-8

    Microsoft - Windows 8 - Wi - Fi & Networking
    http://Windows.Microsoft.com/en-us/Windows-8/WiFi-networking#1TC=T1

    -----------------------------------------------------

    Microsoft - Windows 7 - Why is my Internet connection so slow? (applies to Windows 8)
    http://Windows.Microsoft.com/en-us/Windows7/why-is-my-Internet-connection-so-slow

    Microsoft - Windows 8 - wired and wireless in Windows problems
    http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-8&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • I can connect to my wireless router, but cannot get internet connectivity via Wireless. If I connect the cable to the port on the router, I get internet connectivity.

    Wireless router / Internet problems

    I am running Windows Vista Home Edition with Security Essentials.  I can connect to my wireless router, but cannot get internet connectivity via Wireless.  If I connect the cable to the port on the router, I get internet connectivity.  Is there a firewall setting that could cause this problem?

    Hello

    Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
    Update your WiFi drivers on computers. How you are positioned in the router? Are there
    obstacles in the path?

    Actually try updating your driver and disabling the network logon.

    Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
    version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
    Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    Download - SAVE - go where you put it - right click – RUN AS ADMIN.

    You can download several at once however restart after the installation of each of them.

    After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
    manufacturer of system become your backup policies).

    Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
    updated drivers.

    I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
    are almost always old, and you can search drivers manually as needed.

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    ------------------------------------------------------

    Make sure you know the details of connection to your wireless router - SSID and password.

    You lose connection when you do and have to redo your logon.

    Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
    lower left click on merge or delete network locations - REMOVE all instances of your network (and the
    others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

    -----------------------------------------------------

    Check this box:

    Strange problem with Internet under Vista
    http://www.catonett.com/blog/archives/194

    Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
    http://support.Microsoft.com/kb/928233/en-us

    ----------------------------------------------------

    And:

    Network connection problems
    http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • Error in Windows Mail - "error 623 - system could not find the directory entry for this connection".

    Original title: Windows Vista, Windows Mail, error 623, unable to connect to the mail.
    This problem occurred after a storm. Modem was fried.  Replaced the modem with the modem "2wire" ATT.

    Now get "error 623: the system could not find the directory entry for this connection"or the sys works very well. " Att think maybe in Vista?  Help, please. Works of g-mail, but I like Windows mail.

    Hello Bbuddes,

    You can watch the following information/tutorial to help with most of the problems of Windows Mail.
    http://www.Vistax64.com/tutorials/62560-Windows-Mail-problems.html

    There is a section to reset Windows Mail which can help with your problem.

    Sincerely,.

    Marilyn
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think

  • The D6300 works on a connection ADSL1?

    The D6300 works on a connection ADSL1? There is no ADSL2 + availbility here and NBN is coming...

    Hello Morri

    Yes, this modem should work on the ADSL1 connection.

    DarrenM

  • My internet keeps disconnecting even if the router works fine. He maintains have diagnosed as a DNS error any.

    I have a Samsung RV511 which is only a couple of years.  It has been disconnected from the internet every 2 to 5 minutes or more, but my router works fine.  I got a new power cord, ethernet for her, but the computer continues to disconnect. When I diagnose the problem, it indicates the server DNS does not.  Tried to contact my internet provider, but they couldn't understand why I didn't know every little thing on my computer and made me feel pretty stupid so I'm curious to see if anyone else out there it can help.

    I used to get this problem.  My connection would get a yellow top warning symbol & I could no longer communicate on the internet.  No Windows diagnosis could correct & would only sometimes identify [as a DNS problem].

    I searched for advice, but never really found a convincing explanation or an appeal.  I started using the commands below [that I found in this forum] to restore things.  It seemed most of the working time.

    Several people also suggest just reset the router, but that was irrelevant, because I haven't used one but I tried to remove and then reconnect the modem USB and sometimes helped.

    The problem seems to occur in phases, but I could never understand what was different between the good times & bad times.  I've always suspected the software controlling my USB modem but could never be sure.  I changed the USB modem & the problem went away for months before returning [but less frequently than before].  Now, I have a wireless connection with my mobile phone and use it as my modem for internet connection - 5 months without problem.

    What I did was to open a command prompt [I think he should be executed as administrator], then type:

    netsh winsock reset
    RESTART THE PC
    netsh int ip reset
    RESTART THE PC
    ipconfig/flushdns
    ipconfig/registerdns
    RESTART THE PC

    As I say, this procedure allows to sort out most of the time, but it should reappear later.

  • I'm doing a blank publication widget, but he keeps ignoring my changes of State for relaxation. How can I have my state changes still work for the things placed in the trigger?

    So here's what I have so far. The menu works perfectly, thanks to some Youtube tutorials. And everything is connected properly. But the only thing is that the "WORK" button does not change of State which is set up for this. I tried to apply the change of State before I placed it in the trigger area and after. Doesn't seem to do the job.

    Objective status change is essentially the 'WORK' text will turn white and white space in the run will teal'c also turn teal'c. Thus, the colors will be reversed. I have a link next to it, "ABOUT", which is currently successfully. I suppose that if it is not possible then I'll have to find another design... but I would like to know if there is a way to do it!

    Screen Shot 2015-01-02 at 4.00.17 PM.png

    I believe you are trying to get a color for the composition status when its assets? Please publish the site and provide the url to a glance.

    Thank you

    Sanjit

  • The router just for me

    I had a problem choose a router that will work for me.

    I have a few computers (with Mac in there), a Bravia TV and a PS3. I'm looking for a (cat 5) wired and wireless router that has QoS so that I can make sure my packages of games to get there first.

    I was watching the gigabit routers

    Dual-Band Wireless-N Gigabit Router (WRT320N) Router simultaneously Wireless N dual band (WRT610N) Wireless-N Gigabit router (WRT310N)

    The problem I have is that I can not say that none of them have QoS. Does anyone have advice for me?  In addition, why are these routers Wireless N and not N +? Of course, I'm new to this whole thing router so put me right!

    According to your requirement, you can go for any N-series or series G Router WRT54GS, WRT54G2, WRT160N, WRT310N etc...

    All three model No, you mentioned is to have option QoS to prioritize bandwidth for your devices.

Maybe you are looking for

  • Could not open the Photos after Snow Leopard update to El Capitan

    I have an iMac 3.06 GHz, which has been updated to El Capitan on January 15. Most of the things were going well with the transition, but it seems to be "stuck" now between iPhoto and photo - I don't know how else to put it, but I can't open the Photo

  • DVD drive read not blu - ray

    OK, I just had a dv7-4165dx and wiped and reinstalled windows 7. I downloaded all the drivers for my laptop but it is not reading blu - ray. Is there a specific driver I need? Help, please!

  • Windows XP update problem-

    Some how Windows Update has been extinguished. I went to control panel - automatic updates and it won't allow me to select automatically download the updates. I then went to the Security Center, and still I am unable to change the setings to auto-dow

  • Age of Mythology Rise of the Titans download

    Age of Mythology is one of my favorite games to play although he is old enough. I was install on a new computer and discovered that my takeover of the Titans disc was scratched and no longer works. This expansion has added so much to the game and now

  • How do I set up on my xw4300 ht?

    XW4300 workstation Windows 7 How to set the hyperthreading?