HELP - FPGA SPARTAN 3E-100 CP132 WORKS WITH LABVIEW FPGA?

HI EVERYONE, GET ON IM TRYING TO USE MY FPGA WITH LABVIEW, BUT I DO KNOW THAT IF ITS COMPATIBLE, I INSTALLED THE DRIVERS, MODULE FPGA AND LABVIEW 2012, IM USING WINDOWS 7 32 BIT, AND AFTER I COMPILED ITS SAYS:

LabVIEW FPGA called another software component, and the component returned the following error:

Error code:-310601

NOR-COBS: Impossible to detect the communication cable.
Check the communication cable is plugged into your computer and your target. Also, verify that the proper drivers are installed.

Thank you.

=)

Hi dvaldez2.

LabVIEW FPGA offers no support for any material to third parties, other than the 3rd Spartan XUP Starter Kit. These are probably the drivers you downloaded.

http://digital.NI.com/express.nsf/bycode/Spartan3E?OpenDocument&lang=en&node=seminar_US

However, this driver supports only the Starter Kit Board itself (http://www.digilentinc.com/Products/Detail.cfm?NavPath=2, 400, 790 & Prod = S3EBOARD). You may not use the driver with any other Xilinx FPGAS.

I hope this helps.

Tags: NI Software

Similar Questions

  • How to install the version of nor-Sync 3.1 in the remote system (processor integrated PXI chassis) to recognize the PXI-6682 device to work with labview RT?

    How to install the version of nor-Sync 3.1 in the remote system (processor integrated PXI chassis) to recognize the PXI-6682 device to work with labview RT?

    Hung Nguyen

    Hung Nguyen,

    The installation of drivers for all targets in real-time remotely is more or less the same. First install the driver (in your case the NO-Sync) on your PC, then install it on your system remotely through MAX. For step-by-step instructions, see install the software on your NI CompactRIO controller.

    See you soon,.

  • The jury of ELVIS will work with LabVIEW Student Edition 2010

    Hello

    This question was asked in the forums of LabVIEW, but no solution has been found. I have a windows 7 x 64 machine with LabVIEW 2010 Student Edition. When I try to install ELVIS 3.0.5 traditional software I get the following (no error code) message: "this Setup program requires the LabVIEW 8.5 development system or later to be present on this computer. Development system LabVIEW Base in any version of LabVIEW is not supported. Please install LabVIEW and then rerun setup of NI ELVIS. »

    I also installed the DAQ software for PCI DAQ board. I do not have access to a 32 bit machine and do not know how to get my board work (no ELVIS II) ELVIS. I have provided a screen shot of the message during the installation of the software of ELVIS.

    .

    Hey dduong16,

    Thank you very much for taking the time to provide additional information. After talking with several experts about your system, we concluded that this error is the result of an incompatibility between 3.0.5 Elvis and LabVIEW 2010 64-bit. Even the latest drivers of Elvis are not yet supported by 64-bit LabVIEW: see notes in support of the operating system on the Readme Elvismx 4.2.3

    To solve your problem, you will need to uninstall the 64-bit version of LabVIEW and install a 32-bit version. If you are a student, you should be able to get this version of your computer (it will work fine with your Windows 7 64-bit OS - it will install on 32-bit OS emulated inherent in your system). If you are not a student, please send me a personal message, and we will be working with an account representative to get you the necessary version.

    I apologize for the inconvenience, this made you and appreciate your patience. We have updated the Elvis 3.0.5 Readme to reflect this incompatibility (the change may not appear yet, because it takes time to propagate through our system), and I'm trying to create a Base of knowledge on the subject article to help future users who encounter this error.

    If there is anything else that I can help you, please you after return. Thank you!

    ~ kgarrett

  • Does anyone have a DSO - 2090 Mory working with labview

    Hello

    I have a DSO-2090 Mory which I can't seem to make it work with the provided labview VI. I searched the Board, but have not yet found one another answer that it probably has something to do with the function in the DLL. I have no way to change the dll function so I need now to see what I can do. I walk if someone else has used this DSO before and if so how in the world do you have running? I appreciate all suggestions and advice, other than to get a new dso because this is the one I'm stuck with for now.

    Thank you

    Hey all,.

    It seems that I now have a solution. I contacted Mory and I think it took about a week for them to get back to me, if once they have come back to me, I could start to compuniating back with a tech. The tech sent me another copy of the Vi along a copy of the dll which seems to work.  So I attached the vi but I can't join because of its extension .dll file, so I changed it to a .doc file that will need to be renamed with .dll incase anyone else ends up with the same question.

    Thank you all for your comments.

  • In time real PXI-1031 does more work with labview. "Not enough disk space to perform the backup.

    The labview real-time project was working until a few weeks ago and the only error that is displayed on the PXI is this error message.

    "NEITHER Configuration Manager: not enough disk space for the backup" everything before that looks like it starts very well. Recently, I removed the hard drive and remove the 4 GB network log file because it seemed to me that a file of 4 GB on a fat32 file system was probably the cause of the problem. After that it the project worked when I tested it, but others in my lab said it was broken again the next day.

    Any help would be greatly appreciated because I don't know all that equipment.

    I found that I had "reset IP" set to "yes" in the bios that seemed to be causing my problem because I changed it to no and it seems to work perfectly now. Sorry that it took so much time to understand and I feel like a fool.

  • 8.6 RT works with Labview 8.5?

    I have Labview 8.5 on my desktop and I want to load RT 8.6 from a CD on a target computer evaluation. They will work together? I don't want to upgrade Labview on my desk because then I'll have to go back once the period eval runs out.

    Ben

    I have several Labview version on my PC. They can work side by side. But they cannot share files source or toolboxes. So I guess you can install Labview 8.6 in eval mode and then Labview RT in eval mode. Then you make a copy of your code of 8.5 and store in a separate folder for the test drive of the RT system. After the eval you uninstall just 8.6 Labview and RT module.

  • An external mouse does not work with my Satellite P300

    Sorry, but I m not well speak English.
    I have installed alcohol on my Satellite P300-1FE but my computer restarted
    I did it again, but it is impossible for me to work with my external USB mouse optical mouse "Trust mi-2500 x.
    It s not recognized. Can I update the driver, Vista tells me it's good, but Vista also indicates that it cannot install it.
    Vista gives me the error code "39".

    "When I am looking for a solution, I see the warning: keyboard cherri evolution is not compatible.
    I don't understand. Can you help me?
    I do not work with the keyboard, so it is impossible to not have an external mouse
    Thank you very much.

    Hello

    Error code 39 always appears if the equipment has not been installed correctly.
    I think you should first try this:

    Remove the mouse driver installed and the software.
    Then remove the USB hubs and USB controllers in Device Manager list.
    Then restart the laptop and wait until the USB ports would be installed again.
    Install the mouse software, and then connect the mouse to the laptop.

    If this will not help, try to remove the installed application alcohol because that might be the reason for this compatibility issue.

  • Notes of rogue 6.5 works with Windows 7__

    Help! Lotus notes 6.5 works with windows 7.  I installed notes 6.5 on a pc windows 7 but cannot make it work!  Error: The file could not be created.  Any ideas?

    Help! Lotus notes 6.5 works with windows 7.  I installed notes 6.5 on a pc windows 7 but cannot make it work!  Error: The file could not be created.  Any ideas?

    Hello

    Go to the following site: Windows 7 Compatibility Center

    You will see a tab hardware and software that you can use to locate the product that you want to check for compatibility.

    Select the Compatibility FAQ which will explain how to use the compatibility Web site.

    If you find a piece of software/hardware installed that is not on the compatibility list, go to the website of the developer for this product and check for updates.

    I hope this helps.

    Thank you for using Windows 7

    Ronnie Vernon MVP
  • Oracle Forms stopped working with jre8u51; works with jre8u45

    Oracle Forms 11.1.2.2 works very well with wls 10.3.6

    Last week, several client computers updated for Java 8 51 to update automatically.  Impossible these computers that were once able to connect and receive the error: ClassNotFoundException - oracle.forms.engine.Main

    One of these computers was able to disable Java update 51 8 and able to connect successfully to the forms application.

    What needs to be adjusted to allow the 51 update also work?

    Here's my formsweb.cfg managed by Enterprise Manager 11 g Fusion Middleware control

    jpi_download_page http://www.Oracle.com/technetwork/Java/javase/downloads/jre8-downloads-2133155.html

    jpi_classid clsid:CAFEEFAC-0018-0000-FFFF-ABCDEFFEDCBA

    jpi_codebase http://java.sun.com/update/1.8.0/jinstall-8u45-windows-i586.cab

    jpi_mimetype application/x-java-applet

    Any help in getting 51 update to work with 45 update would be very grateful.


    Thank you.

    Sandy

    I agree that this thread is going beyond the scope of original program. However, I have known and corrected the most recent problem that you have encountered under the Oracle Doc ID 1943873.1 who will provide information and links to the appropriate patch to install. However, I'm not at all sure that you have solved how to properly configure your Oracle_Home to be able to run the Opatch utility that is necessary to install one of the patches above.

  • Work with Lr from a NAS

    I have a NAS (Network Attached Storage) that I use to store all my photos for the backup. However, I was wondering if I could have Lr directly until the NAS rather than keep the files on my original hard drive (running out of space quickly). My NAS has mirrored of drives so if one goes down, I always have a back-up.

    I don't know if Lr will have problems with the network connection via the SATA connection on my hard drive.

    Thoughts, experience, help?

    Yes, you can work with photos on one of the RAID drives and have the other RAID disk-based backups.

    You must point Lightroom to use the RAID drive instead of the internal drive. Please follow the instructions in this document (scroll down to the section called "Part 2 ‑‑ update folder Location"). Future imports should go directly to the RAID drive instead of your internal disk.

  • Working with Zend Framework 2 in Dreamweaver

    Good evening

    How do I configure CC of Dreamweaver to work with Zend framework 2? All of the documentation I've found is on the first version of ZF.

    Thank you for your help.

    I do not work with ZF2. I've only worked with ZF1. However, the configuration is the same for any PHP framework in Dreamweaver.

    1. Access the Site > indicators of specific Code of Site and set as root in a folder at least one level higher than the folder that contains all the class definitions.
    2. Click on the button "+" above the zone file (s) to open the add a file/folder dialog box.
    3. In the dialog box, click the icon for selecting a folder to select the top-level folder that contains the class definitions.
    4. Select the recursive check box.
    5. Click on the more button Extensions, and then type .php in the box that opens.
    6. To close the add a file/folder dialog box, click Add.
    7. Click OK to close the dialog indicators Site specific Code.

    This gives you the code for the framework hints. ZF2 being very large, Dreamweaver takes a little time to scan all files. If you use only a part of the framework, it is more efficient to use the dialog box add a file/folder to add only the parts of the framework you are interested in.

    A disadvantage of the Dreamweaver site management system, is that you cannot specify a folder in a site as being the root of the site. It is therefore difficult to use the site root relative links in a MVC framework. I recently contacted a Dreamweaver engineer for the possibility of designating a subfolder as the root of the site. He was receptive to the idea, then it could be incorporated into a future version of Dreamweaver. For now, the only solution is to create two site definitions and nest one inside the other. The external site contains all of the files inside and outside of the root of the site. The internal site contains only files in the root of the public site.

  • Screenshot VI works fine with Labview 9 but crushes with Labview 10

    Hello world

    I'm using Labview 10 with XP.

    Screenshot VI (available in the .zip in this discussion http://forums.ni.com/t5/LabVIEW/Can-i-make-an-automatic-Print-screen-in-labview/td-p/534790/page/2?q... works very well with Labview 9 but makes Labview 10 crush every time (same computer).)

    Any solution to make it work with Labview 10?

    Thank you

    User

    Hello

    Thanks for posting on the forum of NOR.

    You can find an answer at the end of the same link you post (page 4).

    http://forums.NI.com/T5/LabVIEW/can-i-make-an-automatic-print-screen-in-LabVIEW/TD-p/534790/page/4?q...

    Kind regards

  • Is DAQ Measurement Computing USB - 1608FS compatible with labview?

    I have DAQ USB-1608FS from Measurement Computing company, and I was trying to see if it is possible to use

    This data acquisition with labview 2012. I tried to download the drivers from their company http://www.mccdaq.com/usb-data-acquisition/USB-1608FS.aspx

    but when I tried to use labview in the DAQmx the DAQ tool is not detect it by LabView. So, if anybody out there knows if this data acquisition

    really can work with labview, please let me know.

    Their driver seems to be ULx http://www.mccdaq.com/daq-software/universal-library-extensions-lv.aspx

    and he said that he supports LabVIEW 2012. I suppose you open a sample and the device does not appear? The device is displayed in the Windows Device Manager? It seems that this driver/device will work, there may be just a few questions it initialize properly on your machine (either with Windows or Measurement Computing software). You must be to open a debate on their forums or call their support help line.

    Good luck! Let us know some of the above and, of course, let us know if find you the solution.

    -gavin

  • Raspberry PI connected with usb for laptop with Labview

    Hello

    Please allow me to introduce myself: my name is Bob and I just graduated from the Bachelor of applied science (Physics), in the Netherlands. In education, I followed a course of programming in Labview. However, the course was not very well if I want to start from scratch. (my programming skills are very poor).

    My goal is to learn the basics of programming in Labview. I want to measure the temperature with a probe for example and read this in Labview. I need a data acquisition for this system. I have a raspberry PI in my possession and I was wondering if I could use it to read the temperature from the USB port of my laptop using the PI raspberry. Is this possible? And I have to run some sort of program on the raspberry PI? Or I could better use another device (Arduino maybe?).

    I hope someone could help me to help me get started with Labview. I'm looking forward to learn how to work with Labview and launch a few projects.

    Thanks in advance,

    Bob

    Are you comfortable with writing code on the invoice, pro forma raspberry? This is where you write the code for the acquisition of data and code to send it on the usb as a RS232 serial port. The LabVIEW program would receive all this and it is a very simple program. There is a tool called Linx box that does all this for the arduino.

    https://www.labviewmakerhub.com/doku.php?id=libraries:Linx:start

  • Application errors of the RT with the PXI-4461 with Labview real-time 9.0.1, DAQmx 9.0.2

    HI -.

    I recently converted a PXI time system real OS (PXI-1042 q chassis, controller PXI-8187, DAQ, PXI-4461, DAQ, PXI-6259). I can write and run DAQmx applications in real time with the 6259 very well. Whenever I try to write a labview RT app to use the 4461, however, it will fail. Note that I can use two cards through MAX I tried switching card slots, just in case it was a problem. Both cards worked with labview, the PXI chassis was before Windows.

    Attached are pictures of the screw base demo I built to show the problem. Since I was a mistake (-200758) if I started from the raw strings, I tried to create a MAX task and use it. The task, but he complained of a buffer is too small. I explicitly put the buffer to work around this problem and still get the same error (-200608). I've also attached a screenshot of the software currently on the Max MAX RT PXI system is version 4.6.2 btw. (I installed the most/all this from DS1 Dev Suite 2010 version).

    Please let me know if I hurt something installed, versions if 4461 just don't play nice with the new BT or RT software, or if something is wrong. Thank you.

    Kregg

    The first error you see is (details in the help-> error explain in LV)

Maybe you are looking for