Help: Fuze distorts the sound when the display turns off

Similar Questions

• Can not turn on the monitor on the Satellite once the display turns off after 10 min

  Hello..

  I have a problem with my laptop...

  When the screen turns off after 10 minutes, it no longer lights!

  I move the mouse, try typing on the keyboard, but it does not work...

  to activate the display again once I should close the lid for the hibernation, then open it again!

  I hope that you will help me @_ @!

  Hello

  Check it please http://support.microsoft.com/kb/917332/en-us
  To correct the behavior please download and apply the patch (KB917332) which could be found in the resolution detailed below. I hope this will help.

• The display turns off after a few minutes and shows 'No Signal'

  Hey guys, I was faced with a weird problem recently. My desktop monitor turns off by itself after a few minutes, but the works of CPU, I can hear the fan running and see the lights blink. One thing I noticed, is that when the screen turns off, the light Orange on the processor rest on which flashes normally just. My PC works normally on the mode without failure, but worse, safe mode, but I can't work on my software CorelDRAW. This may be the problem of SMPS? because recently, my entries of mouse and keyboard did not work due to which I got a USB keyboard and a mouse. I recently installed Windows 7 64 bit, but I think that shouldn't cause the problem since I have worked with Windows 64-bit before on the same machine.

  PC configuration-

  Intel Core 2 Duo 4500 @ 2.20 Ghz processor
  ASUS P5QPL-AM motherboard
  3 GB RAM
  No (not sure, maybe integrated) graphics card
  1 TB harddrive

  PS - I couldn't find an exact category for my problem.

  Hey Archer
  Currently, I formatted my Windows 7 and installed Windows 8 and am these problems persist. I have not upgraded but formatted my C drive and installed a fresh new copy of windows 8... so I thnk it may be a problem of the SMP. Can he?

  Hi sunny

  It can or mentioned being SMPS... the reason is... you have already said that the computer or the monitor works fine in safe mode! But since his past even when you install Windows 8,
  To make troubleshooting a
  1. go to the Bios and reset all default by selecting the optimum setting in the bios... Given that your motherboard has got characteristic overclocking and selection of the IGD... let him get by default...  Start the computer and check if the monitor turns off always.
  2. If step 1 does not solve your problem... then go to the power option in the control panel and select your power setting of the high-performance system where you can set your monitor to never go to sleep.  See what's happening... If the monitor still going to sleep even after this setting... then you have a problem with drivers or the motherboard... try updating the drivers and see if that helps.
  3. If the update of drivers did not help... so the next option is to review your material... try to get a replacement screen and see if this could solve this problem... A things you can deduct that if this also fails, then the obvious reason is that your monitor is ok... and problem must be the motherboard.
  4. Firstly check the display port... does it feel loose?
  a. do you have this port pins come out?
  b. your motherboard has two power connections (EATXPWR 24-pin and a 4-pin ATX 12V... are both connected?
  c. your SMP should be at least 400W according to recommendations from the manufacturer to you. Check this box...
  d. then ofcourcse obviously... Reinstall the Rams and other external devices.
  Follow these steps and let me know your comments for each

• Then the display turns off I can't get it back without force restart

  When the display switches off the power due to the low battery power & I can't get this back even when I plug it into the sector and having to force the computer to restart.
  Is there a pref somewhere to turn it off?

  Hello

  When the screen turns off, exactly? How much capacity has battery at the moment? 5 % ? More?
  Try to higher level.
  When you work with your laptop and the battery level is low battery and the alarm alert will appear in the taskbar, but you will be able to continue your work several minutes or connect the power running.

  I'm afraid that your laptop reaches the critical battery level and then maybe is too late for any action.
  Set the low battery level to 10% and when the notification is shown connect power adapter immediately.
  I imagine that the screen doesn't have to be out of all.

• HP Pavilion DV6-6117dx - horizontal flickering lines appear after the display turns off automatically

  The DV6-6117dx model (as well as other HP Pavilion laptops) have experienced a problem where the screen will display a flickering, horizontal line to the top of the screen, after it has been automatically disabled (note: not in sleep or Standby Mode).

  There is a setting to "off the display of [X] minutes" in power options.  I have my DV6-6117dx value dim the screen after 10 minutes and turn it off after 15 minutes of inactivity.  Sometimes, but not always, when I move the mouse to turn the screen back on, a couple of flickering horizontal lines will appear at the top of the screen.  It is very annoying, and the only way to remove them and to have the screen back to normal is one.) put the computer to sleep and wake it or b.) restart the entire system.

  Everything by putting the laptop to sleep and wake-up is not a huge problem, I wouldn't do that, period.  I owned a laptop Toshiba for about 6 years and never had a problem with her like this (the reason why I bought a new laptop was because my old man was 6 years old and the technology was outdated a lot, a lot).

  HP says it's a software problem, but it did come with a way to fix it yet (at least not that I've found).  I ask all the 'Experts' out there if they have a final way to solve this common issue experienced by some models of HP laptops?  I said to uninstall and reinstall video drivers without success.  I said to install video drivers only to AMD, and then only to HP, and then only from Windows Update, but none of these solutions worked.  I said to update BIOS, but it does not solve the problem.  I told him to try to restore the system to the factory settings, but this did not help.  It is obviously a software problem, but nobody at HP seems to have a definitive solution, how to fix it.  Is my only hope to return to my laptop to be replaced by a different model entirely?

  I hope that someone out there has an answer, it's a common issue that I know a lot of owners of portable HP experienced.  Thank you!

  Hello
  I think it's the right time to get in touch with HP and use the guarantee. How to do?
  Click on the link below and choose your country:
  Contact HP worldwide

  You can also try the suggestions from the link below before you send it to the service:

  Common issues with the screens

• WIFI Disconnection as soon as the display turns off Z3

  Hello to all and my apologies if I did this wrong.

  My wifi connection should connect manually whenever my screen turns off. It connect fine, works fine, but as soon as I finished and the screen goes OFF... Hey Presto I need to manually connect to wifi again. It didn't used to do this and it is very annoying. Please give me some advice. I keep wifi during sleep in advance and I have a z3. Please someone help me solve this problem.

  Settings for power management. But I think you have some 3rd party in place applications. Have you installed any task killers?

• Brightness of the display turns off to

  I have an Asus UX50V notebook and vista home premium 64-bit. The brightness of my screen fades. It is clear to decrease intensity on each 30 seonds. Help, please!

  Hello famuchic, welcome.

  To develop which says Halima, if the driver update does not work, you can check with ASUS to make sure this isn't a hardware problem. There might be a problem with LCD backlighting, or maybe a bug in the BIOS. ASUS may have specific information for you and chances are that if other users have encountered problems with this series, ASUS will be able to provide you with instructions on how to solve the problem.

  Have a good one,

  Thank you!

  Ryan Thieman
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• music mute app while the display turns off.

  There is a musical project of my hand.

  but the app still mute when the screen will Dim (the playbook in standby mode).

  How to fix coding or config?

  If the screen should be forced to stay in your application (unlikely) then you want to investigate NativeApplication.nativeApplication.systemIdleMode.

  If weather is nice, the screen darkens and the PlayBook goes into sleep mode, but you want your application to continue to play the same music in this case, you want to study QNXSystem.system.inactivePowerMode.

  I posted awhile back with a summary of this feature , and a link to the Knowledge Base article on this subject.

• Only in Illustrator: file/open "Preview" Panel is out of control in large. The display turns off. How can I control it?

  This should be a problem Apple FInder, but it only happens in Illustrator: if I open AICC, then press command-Open and get several predictable column of the files directory, then go to the right column, a list of graphic files, an Illustrator, a Photoshop, the Preview Panel is so big that the preview itself is there, but out of sight , off the screen, somewhere to the right. I know enough to expand and reduce look horizontally, column by using the angle at the bottom right of the column of directory, but this does not seem to matter. The preview does not appear unless I scroll as much right as I can and drag it. Literally, I can't see the preview of the file that I am after without seeking a large empty space for him. This all sounds stupid, I know, but this should not happen. Any ideas?

  This is a bug. Please read one of the dozens of discussions on the subject in this forum.

• Display turns off

  Hello

  If I use the battery and I don't do anything on the keyboard or the mouse - after a short time (15 seconds), the screen turns off.

  How will I know the display turns off not when I use the battery.

  Best regards Thomas

  Right-click on your desktop, select property, then tab selection screen saver, select power, now put you your screen turn off time forever or any time you wish to in battery mode.

• Toshiba 32RV635D does not power off when the computer turns off

  Hello

  I inherited a Toshiba 32RV635D. I have a PVR based on linux (Mythtv) connected to the TV via HDMI, connected on a Nvidia GT610.

  With my previous TV, a Vistron LCD Panel at low prices, he would go to sleep when the put PC into hibernation and light up when the PC came back.
  This required no configuration of me, he's done right. The Toshiba TV does not work.

  With this Toshiba TV, when the POR turns off the TV turns off screen but is actually still on - power led remains lit in green.

  Same thing with the other way around - if I put the TV in standby and powered the POR, the TV does not respond and I have to manually put out of Eve.

  I updated the firmware and it has not changed anything, and I can't find anything related to power management in the menus of televisions. I even tried just pulling the HDMI cable to the back of the TV so it has no physical active entry, and yet, it does not fall to sleep.

  The Amazon page for TV mentions the power management features, and I expected from what I understand, it should behave the way she.

  I read a lot on HDMI-CEC, but to use it with my existing kit, I would need to buy an adapter USB - CEC, and which seems a little odd because my previous TV not cheap-as-chips just done this...

  Also, the different uses in linux suggests considers its sounds the right - 'xset q' running when the computer is idle tells me that "the monitor is turned off" when in fact it is not.

  Clues?

  Ricklous, it can be useful if you have a look at the url
  http://www.Toshiba-OM.NET/LCD/PDF/English/Country_Specific/RV635-323742-English-specific.PDF

  If you want to download the manual of the English edition for your model, I have not read through, but it may be useful to you.

  Either by the way, I have the model 32RL900A and find only a VCR plugged into the claims of taking SCART screen every time it turns on while the TV is set to a string of FTA (Free To Air) and then 'hands back' screen when he (PVR) goes out, and this, I discovered, is a characteristic of the system SCART.

  I don't know if this information is useful to you, but hope it helps.

  donhe7

• Satellite M300 display lights then the backlight turns off

  I have a M300 Satellite.
  When I turn on my computer the screen comes on then the backlight turns off.
  Display on an external monitor.
  I have tried funtion buttons, move the screen has no effect.

  Any ideas?

  Hello

  Are you able to increase the backlight using Fn + F7?
  Have you checked the power management option that controls the backlight for the different consumption patterns?
  Will you please do because the power management could lower the backlight to save battery.

  If changing the settings of theses will not help, so I guess FL inverter small failures that may cause this problem.
  In this case that the parts must be replaced

• Bluetooth freezes when the screen turns off

  Having a problem with the Bluetooth on my pre. I coupled it with a Plantronics Voyager 855. Initial pairing works very well, but after the screen on the pre turns off, the connection goes bad. When I turn the screen back on, the Bluetooth application on the phone always displays the connected headset, but it is not. If I try to play music, there is no sound, and if a call comes in, I can hear the person on the phone, and not on the helmet.

  About 30-45 seconds after the screen turns off, I hear the high tone of the headset which means that it has lost connection. I don't think that the headset is bad. It worked very well with my previous phone.

  If I have music when the screen turns off, the connection is very good. It's like, when there is no active communication between the phone and the headset, and the screen turns off, the bluetooth on the phone goes into a blocked State. I can restore the connection by turning off bluetooth on the phone and then on again. It reconnects to the helmet, until the next time the screen turns off.

  I tried this to get a better idea of the problem...

  If I remove helmet > disable bluetooth phone > turn on bluetooth on the phone > put the headset in pairing mode, it pairs fine.

  If I remove helmet > disable bluetooth phone > turn on bluetooth on the phone > turn off the screen > wait 45 sec > turn on the screen > put the headset in pairing mode, then it does not.

  Again, it is like turning off the screen causes the bluetooth of the phone hang. Given that the screen turns off fairly quickly, I basically disable bluetooth phone and back on every time I want to use it.

  Any thoughts?

  My problem is solved.  Turns out that I had a defective unit.  He traded last night, and it works fine now.  Got the yellow box this time.  First of all, we had the black cover.

  The swap was a little complicated.  I bought in a store of absolute Wireless in Garner, North Carolina.  It is a reseller of third party.  They did it to a Sprint service center to have a technician "certify" the default before they would replace it by car through the city.  And of course, the service center couldn't do the replacement, so I had to go back through the city to the point of purchase after they certified it.  Best of all, the procedure of "certification" involved explaining the problem to the technician for about a minute, she agreed with me that it was malfunctioned and his writing his employee with the ID on the back of a business card to bring back me to the first shop.  She has not yet turn the phone on itself.  She said pretty much the guy to the absolute Wireless has been a * beep * by sending me to it in the first place b/c, we could just do this by phone.  PITA BREAD.  But I suppose it is, that's what I to do not buy directly from Sprint.

• U2715H - Windows automatically resized when the screen turns off then turn it back on

  • Windows 8.1 Pro
  • 1 single monitor connected to the PC
  • native resolution 2650 x 1440 at 60 Hz the value
  • through CDM of the monitor to the RFP the ti EVGA 750 SC (cable Dell)
  • all drivers updated on 28/12/15

  I just bought this monitor and I noticed this strange behavior. Whenever I have turn off the monitor (or it will turn off by itself), if I didn't have a maximized window, all windows (regardless of size) gets automatically resized to fit in the left upper quadrant when the screen turns back on again.  If I had something full screen, this behavior does not occur.

  I find this very annoying. This behavior happened with my previous monitor, which was only 1080 x 1200.

  I was unable to find any setting for the U2715H disable this "feature". This isn't because EasyArrange from Dell. I do not use this feature. And this always happens with Display Manager not installed.

  Is it just a 'feature' of Dell U2715H? Is responsible for Windows? Help, please.

  TIA

  There was no pilot or changes to the hardware of my first post.  BTW, my monitor is a Rev A02.

  A few days after my previous message, another question emerged.  Monitor flash intermittently ON / OFF every few seconds.  I unplugged/replugged the cable CDM - DP and that seems to fix things... until the next day.  This time, I nothing could fix the random rotation power SWITCH of the monitor.  Desperate, I decided to plug an old HDMI cable, I had to hang out.  Flashing problem has been resolved.  Not only this, using HDMI solved my original problem of auto resizing windows.

  The solution to my original problem: use an HDMI cable.  I went to the Dell CDM - DP cable and the problem has been resolved; no more windows resize automatically when the monitor turns off in sleep/towers.  I always get the native resolution at 60 Hz and there is no noticeable disadvantages to the use of the HDMI versus DP interface.  I've been using the HDMI cable for about a week and there is no other issue.

  Just for additional verification, I bought an Accell UltraAV DP - DP 1.2 cable (B142C-007 b-2), one of the few officially approved by VESA (see link below).  Using this cable does NOT my automatic window resizing problem original.  I do not use it long enough to see if they would prevent the random flashing question.

  I still don't know the exact cause of my original question.  I guess it's a driver problem with DisplayPort standard.  But if you do not need DP 1.2 functionality, I suggest that you just use your GPU HDMI output (if she has a).

  www.DisplayPort.org/.../How-to-Choose-a-DisplayPort-Cable-and-not-get-a-Bad-One

• App background stops when the screen turns off

  I wrote an Android app with a Service that receives events from the LocationService and the accelerometer and always try now to wear 10 BlackBerry. Tests on a Z10 STL100-2 10.1.0.4181

  Once the unit has remained unchanged for some time, the location listener is not registered, in order to save energy, and re-recorded a trip again.

  Don't worry, this can be disabled via the visible activity. But it must continue with the last State (start/stop) after the reboot.

  I even magically figured out how to add additional permissions for the manifest of BAR: "_sys_android_autostart_service" and "run_when_backgrounded".

  But as soon as the screen turns off, my application stops working. No location or accelerometer case being received. Turn on the display again, everything back to normal.

  It is meant to be a question about the accelerometer, but I could not find in the tracker.

  So my questions are:

  -Is it possible to port Android continue to receive events location when the screen is off?

  -Is it possible to port Android continue to receive events of accelerometer when the screen is off?

  -Will my service to continue to operate if more than 8 Apps began after mine? (And the user did not hit the close button)

  -The "headless" 10.2 mode help? (I currently only test with 10.1, because my service provider has not yet unlocked 10.2)

  -Finally, this would be possible with a native application? (I could port the port iOS... lots of fun...)

  Thank you very much for your help!

  PS: If it's of any interest: I use the plugin V1.6.1 Eclipse/ADT to package and install the bar.

  As reported here as well (and I'm sure in other places)

  http://supportforums.BlackBerry.com/T5/Android-runtime-development/accelerometer-turns-off-when-Scre...

  I'm working on a deal in the next version, similar to what we're doing with location requests (in other words, activate us the background mode if your app acquires a partial wake lock).

  Edit:

  So my questions are:

  -Is it possible to port Android continue to receive events location when the screen is off?

  (Yes, but you must hold a wake lock).

  -Is it possible to port Android continue to receive events of accelerometer when the screen is off?

  (For the moment, no, but I'll change that, so it behaves like location.)  Mind you, this could be used to work on old revisions of the software until the native sensors team added a background of sensor mode which is disabled by default and must be explicitly enabled).

  -Will my service to continue to operate if more than 8 Apps began after mine? (And the user did not hit the close button)

  (There are a lot of thing that matters if your Services happens to run or not, which is not limited to, but includes the number of applications already running and the status of the device memory).

  -The "headless" 10.2 mode help? (I currently only test with 10.1, because my service provider has not yet unlocked 10.2)

  (No, it's a native thing.  Your application is already technically without head)