Help the VLANS on Cisco SG200 - 08 p switch voice and data
Hi all
I'm faced with a problem of configuration on the Cisco SG200 - 08 p.
We use Cisco SG200 - 08 p on a mobile carriage which will go from classroom to classroom who will have computer and phone VoIP cisco plugged into it. The question is that each of our closets are in different VLANS (1 voice and 1 data... Let's say data vlan 20 and vlan voice 2025 for conversation) and which move towards every closet.
It would be great if I could just create a vlan voice dynamically pick up this switch upstream has however and generic data, it seems that I was failed to do.
So far, I can pass the data Vlan no probably. The upstream switch port is set to access port and a switch port access voice vlan (these are x 3750 switches)
If the above is not possible, I guess I'll take what I can get. Should I create data vlan 20 and vlan2025 of the voice on the Cisco SG200 - 08 p and make a port on the Cisco SG200 - 08 p and a trunk trunk on the 3750 x? Is there an option on the Cisco SG200 - 08 p to tag voice traffic?
I am also concerned about DRIFTING and I did not see an area in the Cisco SG200 - 08 p to set it as a customer and a transparent mode.
Thanks for any help,
Dan
Playne,
first the bad news, the switches for small businesses currently do not support VTP, they support the GVRP Protocol which is like VTP, but there is no State that the VLAN used it will not automatically learn as VTP.
You should be able to configure the 3750 as a trunk with a vlan 1U or unmarked and vlan 2025 as the tag for the voice. configuration of the port on the switch to small businesses the same way to its home port. All ports which have only phones will be 2025U of access and all ports only PC would be access 1U. All ports of phone and computer would be trunk 1u, 2025T
Cisco Small Business Support Center
Randy Manthey
CCNA, CCNA - security
Tags: Cisco Support
Similar Questions
-
Configure the VLAN voice and data in CISCO SF 300 8 P
I have a couple of Cisco SF 300 8 P and P 24 switches. I have voice and data VLANS configured as:
Data VLAN: default 145.17.59.0/24
Voice VLANS: VLAN 20 172.22.20.0/24
I have different DHCP servers regarding the data VLAN, we have a physical server that is configured for 145.17.59 * extended IP and Voice VLAN DHCP Server is configured as a router gateway with option 150.
This configuration works very well with other cisco 2960 switches and 3750 etc. except CISCO SF 300 8 P and 24 p. I tried to set up the voice and data VLAN in these CISCO switches so that phone CISCO (model 6941) should get IP of the VLAN voice and PC should get the IP address of the DHCP server on the data VLAN. I tried several techniques such as LLDP, Port-to-VLAN Config etc.
Can anyone please guide me / help on this.
Kind regards
A K.M.SayeedHi A.K.M., with Cisco phones you should be able to define simply automatic voice VLAN to be VLAN20.
ID of the vlan 20 voices
You must ensure CDP or LLDP is enabled as well. I would check in the web GUI. DHCP for phones can come from a DHCP server on a port access VLAN20 switch, or you can use dhcp for assistance to redirect DHCP server elsewhere.
If you prefer or you have problems with the CDP or LLDP, you can also program the ports as trunks and add the tag VLAN 20 for them. In this scenario, you need to ensure inter - vlan routing works and phones that download the file config with corrrect VLAN config.
These switches do not run ios, so they are similar, but different from the catalyst switches that you mentioned.
-remember messages useful rate.
-
Trouble with the voice and data Vlan vlan translate between CT3905 and SF300 - 24 p
Hey actually, we have the solution to monitoring of implementation with CT3905 phone, SF300 - switches 24 p cameras and AIR-AP1041N Access Points
We have the problem with the vlan tag in SF300 switch ports - 24 p we can´t tag vlan of the voice and data VLANs on the same port on SF300 - 24 p it is Possible or we must dedicate a port for each VLAN or ussing the same data segment of VLANs and vlan voice?
Someone has an answer or technical documentation that can help us
Best regards
First of all,
Please disable lldp transmit in SF 300 switch.
The command is "no lldp transmitted."
After you disable check the following steps.
https://supportforums.Cisco.com/docs/doc-27005
facing the same problem with cisco SG 300 and 3905 ip phone switch.
And nested thing was my 7945 and 6941 phones use to work properly, without above configuration.
Cisco 3905 became not vlan Ip address votes and even if I put static, it did not work.
After a long struggle, I was able to solve the problem. Now both phone and system work fine in the same port.
Samantha
-
How can I get voice and data to work with the ASA 5505?
Here's the issue I'm having. Can I get a Cisco 7940 to work behind one site to another configured ASA 5505 and I can also get data to work behind it. However, when I try to create a separate Vlan for voice and data, it does not work. Our voice VLANs on our remote sites are 172.30 and data are 172.31, when I put the inside interface with 172.31 data will work and when I on it 172.30 voice will work. I upgraded to a security more license and tried vlan3 created as voice. I have the data to the top and work but I can't get vlan3 to work. Any help would be greatly appreciated. Thank you
Here is my current config:
hostname TESTvpn
activate the password xxxxxpasswd xxxxx
username admin password xxxxx privilege 15
name Corp_LAN 10.0.0.0
name 192.168.64.0 Corp_Voice
name 172.31.155.0 TESTvpnobject-group network SunVoyager
host of the object-Network 64.70.8.160
host of the object-Network 64.70.8.242the Corp_Networks object-group network
network-object Corp_LAN 255.0.0.0
object-network Corp_Voice 255.255.255.0interface vlan2
nameif outside
security-level 0
IP address dhcp setroute
No tapinterface vlan1
nameif inside
security-level 100
IP 172.31.155.1 255.255.255.0
No tapinterface vlan3
nameif Corp_Voice
security-level 100
IP 172.30.155.1 255.255.255.0
No tapoutput
interface Ethernet0/0
switchport access vlan 2
No tapinterface Ethernet0/7
switchport access vlan 3
No tapoutput
dhcpd allow inside
dhcpd address 172.31.155.10 - 172.31.155.30 inside
dhcpd dns 10.10.10.7 10.10.10.44 interface inside
dhcpd sun.ins area inside interface
dhcpd allow insideenable Corp_Voice dhcpd
dhcpd address 172.30.155.10 - 172.30.155.30 Corp_Voice
dhcpd dns 10.10.10.7 10.10.10.44 interface Corp_Voice
dhcpd interface of sun.ins of the Corp_Voice domain
enable Corp_Voice dhcpd
dhcpd option 150 ip 192.168.64.4 192.168.64.3Enable logging
exploitation forest buffer-size 10000
monitor debug logging
logging buffered information
asdm of logging of informationoutside_access_in list extended access allow all unreachable icmp
outside_access_in list extended access permit icmp any any echo response
outside_access_in list extended access permit icmp any one time exceed
access extensive list ip 172.31.155.0 inside_access_in allow 255.255.255.0 any
inside_access_in list extended access allow icmp 172.31.155.0 255.255.255.0 any
Access extensive list ip 172.30.155.0 Corp_Voice_access_in allow 255.255.255.0 any
Corp_Voice_access_in list extended access allow icmp 172.30.155.0 255.255.255.0 anyVPN access list extended deny ip 172.31.155.0 255.255.255.0 object-group SunVoyager
extended VPN ip 172.31.155.0 access list allow 255.255.255.0 anyinside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Access-group Corp_Voice_access_in in the Corp_Voice interfaceGlobal 1 interface (outside)
NAT (inside) 0-list of access VPN
NAT (inside) 1 172.31.155.0 255.255.255.0Enable http server
http 172.31.155.0 255.255.255.0 inside
http 172.30.155.0 255.255.255.0 Corp_Voice
http 192.168.64.0 255.255.255.0 Corp_Voice
http 10.0.0.0 255.0.0.0 inside
http 65.170.136.64 255.255.255.224 outside
SSH 10.0.0.0 255.0.0.0 inside
SSH 172.31.155.0 255.255.255.0 inside
SSH 65.170.136.64 255.255.255.224 outside
SSH timeout 20management-access inside
dhcpd outside auto_config
Crypto ipsec transform-set esp-3des esp-md5-hmac VPN
crypto map outside_map 1 is the VPN address
peer set card crypto outside_map 1 66.170.136.65
card crypto outside_map 1 the value transform-set VPN
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
md5 hash
Group 2
lifetime 28800tunnel-group 66.170.136.65 type ipsec-l2l
IPSec-attributes tunnel-group 66.170.136.65
pre-shared-key xxxxxoutput
int eth 0/1
close
No tap
int eth 0/2
close
No tap
int eth 0/3
close
No tap
int eth 0/4
close
No tap
int eth 0/5
close
No tap
int eth 0/6
close
No tap
int eth 0/7
close
No tapPeter,
Note that access list names are case-sensitive, so you've actually done something different from what I proposed.
Please do:
no nat (Corp_Voice) 0-list of access vpn
No list of vpn access extended permitted ip TESTvpn 255.255.255.0 everything
IP 172.30.155.0 255.255.255.0 extended vpn access do not allow any list allextended VPN ip 172.30.155.0 access list allow 255.255.255.0 any
NAT (Corp_Voice) 0-list of access VPN
In the case where you did deliberately, for example to separate the 2 acl: note that acl VPN (upper case) is also used in the encryption card, where you cannot add a second LCD.
So if you want to separate you, you will need 3 access lists:
list of access data-vpn ip TESTvpn 255.255.255.0 allow one
voice-vpn ip 172.30.155.0 access list allow 255.255.255.0 any
access-list all - vpn ip TESTvpn 255.255.255.0 allow one
access-list all - vpn ip 172.30.155.0 allow 255.255.255.0 any
NAT (inside) 0-list of access vpn data
NAT (Corp_Voice) - access list 0 voice-vpn
outside_map 1 match address all vpn crypto card
Don't know if this was also clearly to my previous message, I recommend you to replace the "all" (in each of the ACL lines) to something more specific (i.e. a remote network, or group of objects that contain the remote networks).
HTH
Herbert
-
Lack of voice and data at the same time kills me
After using a treo 750 (WM 6.1) on att for the past three years, I guess I did not realize the advantage of ATT and gsm in general. There are many drawbacks... mainly pricing for simple accounts (However their family plan was directly comparable to those of sprint). I constantly try to use data applications while talking on the phone without success. I started thinking that I could do without, but a week later, I still really really miss. My wife did too... because she's I usually give directions or any other web information while on the phone. There is nothing like view google satellite map to help someone make sure they are in the right place... "see a big tree on your right with a large Brown building behind it, Yes, it's that one" does anyone else have this feeling? WiFi is not an option for me most of the time.
Voice and data at the same time is not available when using any CDMA network due to network constraints. This is true for all types of phones, not only Palm or not only the Pre. Your example of electronic control or by using google maps, the gps data that can be stored before you activate the call. try to browse the web while making a call and try to go to a web page, you have never visited before, so that you know, that he cannot be a version collected page.
-
What is the procedure how to make my system image backup and data through Windows NAS Server?
I work the iMac with bootcamp for Windows 7 - Home Premium.
I want to return to the system image and data etc. of the 'Windows Back up and Restore' to my Synology NAS (network attached storage). When I do the setting changes, I could not find the option to connect to the NAS, but have only the offer to connect to the external hard drive.
(1) the 'Windows Back up and Restore' allows to connect to the NAS for the back of my files, in particular for the iamge system? If not, any other method to make the back upward, especially for the system image?
(2) what is the procedure how to make my system image backup and data through Windows NAS Server?
Original title: save the Windows image
Backup to a network location is not supported by Windows 7 Home Premium. Do you need Windows 7 Professional or ultimate edition.
http://Windows.Microsoft.com/en-GB/Windows7/where-should-i-save-my-backup
-
Problem blackBerry Smartphones on the use of the voice and data
Hello
When we use the Blackberry Desktop Software for backup/restore data from one phone to another, will check voice and data usage in the session "peripheral and buyer information - status remorse" also be restored from the old phone or affected by synchronization? Or will they count just use since the first use of the new phone?
Harold Lee
I have to admit, I am not an expert on this subject, but that is my impression. Once you get the new phone running, your meter would reset to zero on this phone.
-
How to configure the VLAN for Cisco SG500 - switch 28
Hello
First of all, it's my first post here, I hope that someone can help me and please be patient because I am very little known.
OK, so let me explain to you the scénarion I face and I hope someone can help me.
We have a Cisco SG500 - 28 port gigabit switch in our workplace.
Our goal is to create 3 VLANs and separate networks between the various departments.
Vlan1 (which is the default VLAN in the switch)-will be used for the COMPUTER service and management.
VLAN100 - will be used for business.
VLAN200 - will be used for clients who need to connect to internet via WiFi.
I created VLAN100 and VLAN200, and VLAN1 is there by default.
I want to use port 13 for VLAN200 and to connect the-Wifi access point there.
The uplink is in port 25.
I would be happy if you could explain things first to a more general, abstract level, and then we can look at the specific scenario that we have.
SG500 Cisco - 28 Gets a Sophos UTM 9 router internet.
I need to take care of the inter - VLAN routing so, subnet and DHCP
Thanks in advance,
Sincere greetings,
D
Hi Desmond, looking at this DHCP pool it looks correct.
For the second part, you waant VLAN 200 only work on VLAN 200, that's fine. So if you have an access point, and everything on the VLAN 200 connects to the access point, you can make an access to this list. The access list is entered only, which means the inbound interface.
So if you have a gateway connecting to #1 port. You'll need to build the access list and apply it to port number 1. That's assuming you make a list of access 'decline' subnet source IP of VLAN 200 destined for the other subnet, that you do not want access.
The image on another post to fill out your reference numbers, then for the ACL link, it should be placed on the interface VLAN 200 first comes to the switch (IE, the port the access point connects, make sure that you choose to bind by port instead of per VLAN)
-Tom
Please mark replied messages useful
http://blogs.Cisco.com/smallbusiness/ -
Help the flicker of screen HP Elitebook 8460p &; question flashes and upgrade.
Greetings,
I have a problem with my Elitebook 8460p. My old servant me service for 3 years. We have a good relationship with highes and downs. Changed hard drive, the improved Rams, monthly cleaning and etc.
In any case; I have a problem with flickers and flashes. When I push the start of (the computer On / Off), some strange black lines appear and never went. The funny part is that the black lines, flashes / flickers become crazy when I touch the touch pad. But if I touched the touchpad of the black lines just less.
Things I've done;
Electrical parts Checked - no electric leakage (verified to the ohmmeter)
I tried to run with AC and battery - nothing has changed.
I've been handicapped ambient light sensor - nothing has changed.
I've been disabled touchpad - nothing has changed.
Formatting, update the BIOS to the latest version of w7 updated, no unknown device, performed stress test CPU GPU & played back & assemble nothing has changed.
My suspicions;
CPU because this computer VGA card integrated with CPU. Change CPU, maybe to fix any problems.
I want to switch my computer to my choice and i7: Intel Core i7 - 2670QM.
My booking / questions;
Intel Core i7 - 2670QM CPU is compatible with my Chipset QM67? If it is compatible; What should I do? (Updated the BIOS, or different version of BIOS etc..)
I have some information on this situation and my laptop.
HP Elitebook 8460p series using Hannstar MV6 and my motherboard is same. No VGA. I will not worry the my solution. If I'm wrong; I spend my money for nothing.
I'm waiting for your answers.
Thank you.
Really? No response. Thanx HP.
I found the answer. -
VLAN voice and data on a single port
Hello
I have some 5548 P Dell switches, but I just Cisco environment.
I find a lot of information on this but most of it relevant to the VLAN marked and unmarked on a port in general. Some articles suggest to put the port in trunk mode...
anyway (without taking into account the QoS) how you would accomplish this example Cisco on a Dell switch:
Switch (config) #interface g0/1
Switch(Config-if) #switchport mode access
Switch(Config-if) #Switchport access vlan 50
Switch(Config-if) #voice switchport vlan 10
Thank you!
For general mode, commands would be present as follows.
Console (config) # interface gigabitethernet 0/1/1
Console # switchport mode general
Console # switchport general allowed vlan remove 10
Console # switchport General allowed vlan add 2,3,4,50 tag
Activate console # vlan VoIP
Trunk mode:
Console (config) # interface gigabitethernet 0/1/1
Console # switchport mode Trunk
Console # switchport Trunk allowed to remove vlan 10
Console # switchport Trunk allowed vlan add 2,3,4,50
Activate console # vlan VoIP
-
How to create the VLANS on Cisco PIX 6.3?
Hello
How to create a vlan on pix - 6.3? I'm a little confused.
How can I assign one side of the internet with several (not secondary IP address) ip address for each & every vlan?
How I connected to the switch, I mean if I put "switch trunk mode port" on the side of the switch, what command should I I need on the PIX 'inside' interface? in the router, the command is "encapsulation dot1Q 1.
also there are restrictions which limited only VLANS can be created or is it unlimited?
Hello
When you configure your interface, usually do you it like this
interface ethernet0 car
Auto interface ethernet1
Ethernet1 is a trunk with a vlan 2 and one vlan native, you must add to your config:
logical interface ethernet1 vlan100
logical interface ethernet1 vlan200
After that, you must name these interfaces and define the level of security.
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
nameif V200 interieure4 vlan200
nameif vlan100 V100 securite6
This configuration will give you an interface (eth1) with 1 vlan (inside) 2 and native vlan tagged (v200 and v100)
PIX won't negotiate a trunk, your switch configuration is correct.
-
Turn off or disable the voice and data roaming notification over Vibe X 2
Hi all
-what someone has any idea how to turn off the question when you make a call outside your network home, as different country... its boring as hell and can't find the function. Phone is VIBE X 2 4.4.2
Thank you
Lollipop Android came out and fixed the "bug".
-
SG200 or SG100 switches of the series?
Hello
I am helping a company data selection switch and VoIP for a small company of about 40 users who is penetrating new spaces and adding VoIP.
The subnets of voice and data will be routed to the other. No VLAN or QoS are necessary according to the VoIP provider.
They need ports gigabit PoE 22 for phones and no PoE ports of 40 +.
The part-time computer scientist on the spot has no experience in the management of the switches. So, they think about the use of six switches of SG100D - 08 p unmanaged for the PoE ports with all what SG100 switch to non PoE ports. However, it seems that both switches of series SG200 (SG200 - 50 p and SG-200-50 or SG200-26), would be easy to set up for this purpose and require little management. They have most of the equipment rack mounting. It seems that SG200 switches would solve what could be a mess of this and son with six SG100D - 08 p of
I understand that little, if any requirements for a non - PoE switch SG200-xx. Is this correct?
Can someone please comment on how the SG200-xxP switches are easy to use and advice or suggestions?
Thank you
Caseranch
Hi Caseranch, please consider that SG200 switches are not POE on each port only 1/2 of the ports. At a switch 48 Port POE 24 ports. I know this should meet your requirement, but for the future expansion of POE, another POE switch.
You're right, in this sense, the SG200 needs very little to zero configuration. The only thing I recommend is if you buy a switch to manage, upgrade to the new firmware, factory reset the device and then install and connect things for her. This should be sufficient based on the way you describe things.
-Tom
Please mark replied messages useful -
Can't change phone IP auto macro smartport vlan native on SG200
We have a few SG200 switches and I try to configure the macros Automatic smartport for the IP phone and IP Phone + Office. Every time I have change the macro and change the VLAN native to what I want (the VLAN voice is OK but not the vlan native, I want desktop computers to connect to), I click on apply, but it automatically changes the VLAN default native VLAN (in our case 1 VLAN). I'm trying to change it to VLAN 2. Any ideas why it won't let me change the VLAN native? I can change the VLAN native on others, such as switches, routers, printers, comments, etc., but not the two above and the desktop as well. These three will not change for some reason any. Thank you!
Hi Brademeyer29,
what you see, unfortunately, this isn't a matter of configuration. This was reported to the engineering team and should be fixed in the next firmware version 1.4.1.
For now, you will have to use the solution as not changing not VLAN native or not use smartport.
Kind regards
Aleksandra
-
Configure the vlan with SG 300 - 10 p and 520 SA
Hi all
Forgive my ignorance, but I need help with the basic configuration.
For a small office, I bought an appliance of security SA520 (for future VPN with another remote desktop) and a switch of SG 300 - 10 p to connect 3 PCs and 3 IP PHONE. The SA 520 is the router. I have to configure 2 VLANS on the switch:
VLAN2: DATA (for PC)
VLAN3: VOICE (for IP PHONE)
VLAN1: BY DEFAULT.
How can I configure simply all ports?
I would like to configure ports 1-4 on 5 to 8 ports and VLAN2, VLAN3 and G10 port is reserved for the SA520 router.
I want to split VOICE and DATA network.
I think I need to create a trunk on G10 to SA520...
Can someone help me?
Hi Julien,
OK sounds like you use it vlan by default for network management and the vlan 2 for vlan3 for voice and data.
I use a calculator for this, my SA520 is ready at the present time.
Step 1 On the SA520 add vlan 2 and vlan 3 and label them voice and data respectively.
Step 2. Allows you to use the switch port 4 on the SA520 as a port to shared resources to the SG-300.
(my intent is to use vlan1 not tagged vlan tagged 2 and vlan tagged 3 on the uplink of the switch and the SA500.)
To do this, I have to say the SA520 port 4 of the switch will be in trunking and not access mode.
You will need to check the membership of vlan 2 and vlan 3 on switch port 4.
Step 3. Now add a few IPS to VLAN2 and VLAN3
Step 4. Create DHCP scopes if that is what is needed on the SA520
So now I hope that we have the SA520 with the associated IPS VLAN1, VLAN2 and VLAN3
We also have the switch port 4 as a network interface
We are vlan1 reproducing unidentified and vlan2 tag and tag to the SG-300 switch vlan3.
We do the opposite on the SG-300 switch.
If you use G10 as the uplink to the SA520 you'll notice of default port 10 must already be in trunk mode.
Switch ports G10 should be marked for vlan 2 and labelled for vlan3. It will be, default Gi10 untagged for vlan1.
Make sure you keep ports switch is correctly set up.
Best regards, Dave
Maybe you are looking for
-
Need Drivers USB for Equiem A60-173
Hi, I wonder if any of you can help me. I have problems with my USB ports. He won't recognize anything except a USB mouse that I use. It does not recognize any of the MP3 players I tried to connect. I made the diagnosis and sometimes windows says tha
-
Qosmio F50 - LEDs start blinking when I plug it in the socket
Recently, when I plug in the mains, the LED on my Qosmio F50 start flashing, as well as the led battery... the only way to prevent this is to plug the laptop before starting... Can someone explain what this can be?I guess that there may be something
-
LV 2016 Different behavior For Dynamic Dispatch (bug, perhaps?)
-
How to get tilted periodic waveform in labVIEW?
Hello I want to draw a waveform that has range of 0 to 360 and have a frequency of 50 Hz. the logic that I used in my code is like: 50 HZ = 0.02 seconds. 360/0.02 = 18000 (means multiply each sample to 18000 to get inclined wave that offers an amplit
-
SIT: Settings of Inline of Matlab: Simulation Environment &; remote target
Hi all When I inline in a Simulink model parameters, and when I run it in the SIT Simulation environment, it's as if they would not have been treated in inline mode. Each block of the model appears. And when I try to launch it on a remote target (PXI