Help VLAN SG300

I have install successfully one VLAN but...

Since 192.168.1.x I can ping everything on 192.168.50.x

Inside the ports VLAN 50 5 & 6 both the portable and the nas server can talk to 192.168.50.1.

Since 192.168.1.x, I can access all the 192.168.50.1 resources.

Inside of VLAN 50 I can ping 192.168.50.1 but can't access anything that anybody else in the VLAN or off.

From the 192.168.50.100 laptop, I cannot ping 192.168.50.50 (NAS), but I can ping the 192.168.50.1 gateway. I can't ping any internet addresses.

New kind of learning VLAN here. Any ideas why this happens?

Hello and thanks for the reply.

I'm sorry, I didn't know what was the purpose of the configuration.

If what you're trying to do is to configure your network if the switch then makes the routing steps:

1 - Position the layer 3 switch

2. create the VLAN

3 assign Ip addresses to all the VLANS.

4 - for all VLANS can get out to the internet, you must create a default route on the switch. It should look like this: 0.0.0.0 0.0.0.0 IP_address_of_router

5. on the router, you need to create static routes for all the VLANS the router does not know. When you create the static routes, be sure to send this traffic to the IP address of the switch on the same VLAN as the router.

6 - buy last, perhaps the most important of them step is to ensure that all PC use the IP address of the switch as the gateway by default for the VLAN to which they belong.

Try this and let us know if it worked. Also, feel free to ask ay if something was not clear enough.

Tags: Cisco Support

Similar Questions

  • Interface VLAN SG300-28 Firmware 1.3.7.18

    Hello

    I just my SG300 to update the last firrmware 1.3.7.1.8 and I met this problem:

    -By default, the interface VLAN has been activated, but the display is always disabled

    -I can not change and I can not ping to the VLAN IP interface as well (I gave an IP 192.168.10.1)

    Is this a bug? Does anyone know how to fix this? Please help me!

    Appreciate your help

    Minh

    minh06,

    You upgrade the startup code for Sx300_FW_Boot_1.3.5.58 ?

    -Marty

  • Routing inter - vlan Sg300-28

    Hello

    Thank you and thank you in advance if you can help with this simple configuration

    SG300, how can mode layer 3, you make 2 VLAN see each other?

    In my lab at home:

    Default Vlan1 (GE1: access mode) 192,168,2.254

    Static VLAN10 (GE24: access mode) 192.168.10.1

    Town of Port GE25: Trunk Mode directly connected to interface my router 192.168.2.1)

    Vlan1 can communicate with the outside world and the internet, for example, to a different subnet: 192.168.1.0

    VLAN10 is not visible from the outside and from VLAN1

    How can I allow traffic from VLAN10 through the commune GE25 Port to the outside world?

    The router config says: VLAN10 is diretly connected to 192.168.2.1, but I can't ping. I wonder why?

    Concerning

    Minh

    --------------------------------------------------

    VLAN #show SG300

    Created by: D-default, S-Static, G-GVRP, R-radius assigned VLAN

    Ports created by virtual local network name

    ---- ----------------- --------------------------- ----------------

    1 1 article gi1-23, gi25-28, D m 1-8

    10 gi24 S VLAN10

    Ip #show SG300 road

    Maximum parallel paths: 1 (1 after reset)

    IP routing: enabled

    Codes: > - best, C - connected, S - static

    S 0.0.0.0/0 [1/1] via 192.168.2.1, 36:24:22, vlan 1

    C 192.168.2.0/24 is directly connected, vlan 1

    S 192.168.10.0/24 [1/1] via 192.168.2.1, 27:23:12, vlan 1

    He had to set the default gateway on the switch to 192.168.2.1

    -Tom
    Please mark replied messages useful

  • Need help ACL SG300-52

    Hello

    I use the switch SG300-52, I need to know can I block some sites for specific IP / MAC through this switch?

    Help me please if anyone can do it.

    Hello Ramirez,

    The first consideration is that the access list is inbound only, so if you want to block a Web site, the ACL should be applied on a port to connect to the host, not the uplink port.

    A list of examples one block access of google.com IP address would be like this

    «die google» extended IP access list

    refuse any 74.125.21.139 the ip 0.0.0.0

    allow an ip

    The 0.0.0.0 represents a single host address. You must bind to an interface

    interface gigabitethernet5

    Service-acl input of "die google."

    Everything that connects to my IG5 port will not be able to access the 74.125.21.139

    If a port is set too much for you, you can also link the ACL of a VLAN.

    -Tom
    Please mark replied messages useful

  • Setup VLAN SG300-52 beginner

    Hello world

    I appreciate, it's a very beginner question and there may be a few facepalms is going to happen, but I could do with help.
    We just bought a SG300-51 switch to enable our businesses to grow. I'm trying to set up 2 VLANS (1 containing a router, the second comes from my pc at the moment so I have test).

    • VLAN 1 (the default) works obviously fine with access to the internet.
    • VLAN 2 (which is the vlan id 10) doesn't have access to the internet.

    For note, our router is run so I have no control over that.

    So for now 1-2 Ports are on the vlan 1 under Access. Port 3 is in vlan 2 access. I changed the 3 to the trunk port, but nothing helped. All traffic is marked as not signposted on all ports.

    IP addresses assigned on the vlan 1 are allocated from the router from 192.168.1.1 to x.x.1.254 (the router is 254). The switch for the vlan 1 is at 192.168.1.1.
    Assigned IP address in vlan 2 (by aboard dhcp on the switch) are 10.0.10.1 - 10.0.10.254 (the 10.0.10.1 switch setting).

    I have an IPv4 static route from: 0.0.0.0 to 192.168.1.254.

    Now, I don't know I'm missing something fundamental and I read through the article furiously to try to discover what is happening, if someone could help and point me in the right direction, I would be very grateful.

    Thanks in advance.

    I could be wrong, but I think it should already be in mode L3 because it appears that he has been able to assign addresses IP interface VLAN 1 and 10.

    If your PC is plugged IG3 access vlan 10 then you should use 10.0.10.1 as your default gateway and you need a way back to 10.0.10.0/24 via 192.168.1.1 in your router/firewall

  • Setup VLAN SG300-20

    Hello! Everyone.

    I have 2 small business sg300 switches connected through a catalyst 2960S, I created 2 VLANS and VLAN 3 on two SG300 connect my servers, but those who do not work properly. I connect a pc to a port in each VLAN on the two switches, then I test ping interfaces connected to this VLAN, but sometimes I only connections of a switch, and nothing when I try the second switch. Or I can reach almost all interfaces connected to the switch and one of them does not.  When I disconnect and connect to an interface connected to these switches and try to test again the results change other behaviours.

    I Don t need to route via VLAN I want only the link between each VLAN. So I Don t know if it s necessary to assign an IP address for VLANs

    I made the other configuration using the web interface:

    • I created 2 VLANS and VLAN 3 on each switch SG300 manually and ports assigned to VLANs
    • I configured an each SG300 as TRUNK switch port to connect to the catalyst 2960S. And other ports such as access mode.
    • In the Cat2960S, I configured the ports connected to each SG300 as TRUNK and the traffic of VLAN enabled if these ports.

    The thing is, I don't know what is the problem in my setup. I thought on the GVRP Protocol implementation but Cat2960S support only VTP.

    Does anyone know the right steps to implement this configuration or what is the process to implement the GVRP protocol using these 3 switches?

    I have attached my diagram to know what I m doing.

    Best regards.

    Hello

    In the two SG300 switch:

    Configure the port Fe0/19 in the trunk and VLAN enable this port 1U, 2T, 3T (can be configured on GUI)

    Cat2960 switch:

    Configure the port Fe0/11.0/12 in the trunk and leave all the VLANS. (Vlan 1 must be native.)

    concerning

    Deborah

  • Configuration of Vlan SG300-20 for the desktop and server ESXi

    Hello

    I'm fairly new to network so please, be gentle.  I'm setting up a number of VLANs for my lab at home.

    I recently moved jobs and took an Oracle Apps of the Middleware & role has therefore need to start picking up the Apache, e-Business Suite, etc. of the load balancers so need to segragate my network to allow different configurations, I want to install in my lab ESXi.

    My setup is detailed below:-

    I have a router of dryatek 2860n which is my entry for the installation of the internet on IP 192.168.1.1

    My Cisco switch has been set to 192.168.1.2 and the installer to use the 3 layer.

    I have a number of PCs connected to my switch I want to use to administer my ESXi server and have access to the different VLANS.

    VIRTUAL LANs, I need are the following

    VLAN 1 192.168.1.x/24 By default / Internet Uplink
    VLAN 12 10.0.12.x/24 Workstations
    VLAN 13 10.0.13.x/24 Server management interface
    VLAN 14 10.0.14.x/24 Public Interface Server
    VLAN 15 10.0.15.x/24 Private server interface
    VLAN 20 10.0.20.x/24 Storage

    My esxi server has two network interfaces that will have traffic MGMT, Public and private configured as virtual interfaces in ESXi and one that runs my traffic of storage/nfs mounts on a QNAP NAS, I want to make it work on my network

    Here is how I have the ports

    A Port VLAN membership
    G1 VLAN1
    G13 - 20 VLAN 12

    Need to access the VLAN 1, 13, 14, 15, 20

    G9

    VLAN 13, 14, 15

    G10 VLAN 20
    G7 - 8 VLAN 20 LAG configured to QNAP NAS

    G13-20 are my workstations that need to be on VLAN 12, but must also be able to connect to 13, 14, 15, 20, SSH, RDP, NFS

    G9 is the Interface of MGMT of ESXi who need to have traffic on VLAN 13, 14, 15

    G10 is ESXi storage Interface that needs to access the VLAN 20 only

    G7/g8 are connect to QNAP that ideally I want to configure as a LAG.   When I get more interfaces in my ESXi Server I'll finally the team to match.

    I set up an ip interface in my CISCO switch to 10.0.12.1 as gateway to my workstations and created a static route in my router to allow traffic to the switch.  This does not quite yet.

    I also installed a default route to 0.0.0.0

    I followed a number of guides, but struggling to get my head around concepts and how to achieve the above configuration.

    Ideally, I want to configure this through the CLI as Ive had no end of problems with the web interface of the Cisco switch.

    I believe need g9 of trunk, and other ACCESS is it exact.

    How the workstatations to access the other VLAN?

    Any help would be appreciated

    Thank you

    Paul

    Hi Paul, to break it down a little.

    Host A connects to port 13.

    config t

    int gi0/13

    switchport mode access

    switchport access vlan 12

    ESXI connects to port 9

    config t

    int gi0/9

    switchport mode trunk

    switchport trunk allowed vlan add 13-15 (keep in mind this vlan 1 is unmarked here and is the IP of your server interface)

    This translates

    ESXI = 192.168.1.x 24 gateway 192.168.1.2

    interface vlan 1

    IP 192.168.1.2 255.255.255.0

    no ip address dhcp

    Host A = 10.0.12.x 24 10.0.12.1

    interface vlan 12

    name of the workstations

    10.0.12.1 IP address 255.255.255.0

    With this basic host configuration at shall communicate to ESXI (no other config on the switch)

    If please try to get the connectivity of base first, then can work on the roads and DHCP.

    -Tom
    Please mark replied messages useful

  • Routing 10 help Cisco SG300

    Hello world

    I need help.

    On my cisco switch/router I created 4 VLAN using the underside of the interfaces

    192.168.1.254 if ip address of the switch

    port 1 which is vlan1 connected to my router Netgear WDNR4500 wireless

    Port remains connected to the separate NICs on my VMWare Esxi host.

    When I create VM in each individual communication vlan is fine and I can ping the virtual machines on different VLANs.

    My problem is that I don't get any internet access from any device connected to the VLAN specified, with the exception of vlan1

    If I ssh into my switch I am able to ping the dns servers of my ISP 194.168.4.100, for all other VLANs, but this is not possible.

    Not really sure what I did wrong or what I need to access the internet for my vm.

    In my netgear router, which is 192.168.1.1 I have configured the following routes of statis.

    All the vm connected to different VLANs can ping 192.168.1.1, but it seems communication stops there, he cannot go beyond.

    When I do a track of a virtual machine connected to the vlan 10, I get timeouts once received at 192.168.1.1

    My laptop which is connected to 192.168.1 network is capable of tracert beyong my router.

    If someone could help or provide feedback, it would be appreciated.

    More information is needed please let me know, I am a novice, so why I don't know how to solve this problem.

    Thanks to you all.

    Hi houta, this is correct behavior. The default gateway should be the interface vlan Ip address.

    If vlan 20 is 192.168.20.1 any machine linking in vlan20 gateway should then be 192.168.20.1

    -Tom
    Please mark replied messages useful

  • SG200 to VLAN SG300

    Hi all

    I have a client with of several SG300 for VLAN1 for data and voice VLAN10. PCs are piggy is interrupting the phones and showing in the fine SG300:

    A Department has recently employed more people, so we have a SG200 switch to connect the computers and phones. I don't seem to be able to get all the connectivity between the new switch and the SG300 it should connect. I have installation VLAN1 and 10 according to the images below:

    (Most likely) I'm missing something obvious here?

    Thanks in advance.

    If all ports are 1u, 10 t between the two switches, there is a different problem.

    I guess it's possible that the new switch SX200 can act only wobbly. Pass you any firmware prior to installation?

    I probably load the latest software and the switch to make sure it isn't being weird with you.

    -Tom
    Please mark replied messages useful

  • VLAN SG300-10 Questions

    My apologies if this has been asked before, but I have a few questions on setup of my new switch and network. I've never worked with before switches, so it's quite a learning experience. The image above shows the current provision of my network. Here's how I tried to implement, so far.

    VLAN 1 [1-4 Ports, unidentified, trunk] (172.16.1.1/24)

    Workstation A (wired)

    172.16.1.2/24

    Server B (wired)

    172.16.1.3/24

    VLAN 2 [Ports 5-8, unidentified, trunk] (172.16.2.1/24)

    Server C (wired)

    172.16.2.2/24

    Server (wired)

    172.16.2.3/24

    Server E (wired)

    172.16.2.4/24

    Server F (wired)

    172.16.2.5/24

    VLAN 3 [9-10, unidentified, trunk Ports] (192.168.1.1/24)

    G laptop (wireless)

    DHCP through a router

    H laptop (wireless)

    DHCP through a router

    Laptop I have (wireless)

    DHCP through a router

    Wireless router

    192.168.1.254/24

    Now, my goal is to have all 3 VLAN power talking to each other but also have VLAN 1 access to the internet through the wireless router. In the future, I also Server B to be able to expose services (http and ssh) outwards. VLAN 2 should not have access to the internet at all. I know that I can add static to the wireless router, if necessary routes. All three laptops, can access the internet via the wireless router, with no problems.

    So my questions are:

    (1) is there something inherently wrong with the design of this network? If so, what could be changed?

    (2) 3 VLAN isn't really necessary?

    (3) what I need to do, to get the 3 VLANS communicate with each other?

    (4) what should be the doors, to get internet access 1 VLAN?

    (5) what would need to do, to expose services from Server B to the outside?

    (6) what static routes can I add?

    Thanks in advance!

    Jer

    Hello Jeremy,.

    I think that the problem is probably in the router does not route traffic to the switch. That no interface you specified in your career? Once the routing works, DNS should also work.

    Kind regards

    -David Aguilar

    Cisco Small Business Support Center

  • VLAN SG300 - 28 p L3 Question

    Hello

    I'm fighting for the last 20 days to learn how to change IP address on my switch. When the switch came 1st time, he grabbed a my server DHCP address. I changed the config instead of default L2 L3 configuration. After that point he does give me not an option to change the static IP address. I changed to static IP, but it allows me to change the mask only.

    My need is to change the IP Address of the interface vlan1 to be du.1 default gateway. So far, I am unable to do so. Attached screenshot shows that the IP address field is not modifyable.

    Any ideas?

    You have activated services (security-> TCP/UDP services)? and copied running at startup? ('Save')

    Svein

  • Creation of trunk of Cisco 6513 to Cisco SG300 - 10 p for Shoretel phones

    I plugged a new Cisco SG300 - 10 p in an access on our Cisco 6513 port, which is in vtp mode.  I think I will need to create a trunk port of the Cisco SG300 - 10 p 6513, to carry out my office data vlan 1 and my new vlan 112 shoretel VOIP.  I believe that some how all ports are in mode trunk on the default sg300.  I have attached a picture of what it looks like on the management area of vlan sg300.  For some reason any I can plug 3 phones in the sg300 currently just plugged in the 6513 access port and one of the 3 phones come with the vlan voip good 112 and goes into the service very good.  The other 2 phones come but show no service, until I closed the port on sg300 for these other 2 phones and then put the ports back up, then the phones go up.  All of this without going through the port on the Cisco 6513 as a trunk port, it is only now as an access port vlan 1 data and vlan 112 voip vlan.

    My question is, should I put the cisco 6513 in trunk mode and the sg300 will attempt to become the server in vtp and ruin my entire network.  This is what scares me, because I've heard the horror stories of what happens.  My other question is if I have to put the port in trunk mode on him going the sg300 6513, it causes all future phones at the same time without problems?  What would be the cause of 1 of the 3 phones to come as they do and 2 others to come after stop int and put it up?

    Thanks Dave

    Double post.

    Go HERE.

  • Need help to set up voice VLAN in SG300

    Hello

    I spent too much time on it now and need help. I'm trying to set up a voice switch VLAN on a SG300 - 28 p. I need to charge a phone Cisco 7965 connected to a port on SG300 - 28 p to use VLAN 100, and a workstation connected to the phone to use Cisco 7965 on VLAN 101 by SG300 - 28 p. In the common Cisco IOS switches, this task is configured as follows:

    interface gi25

    switchport mode access

    switchport access vlan 101

    switchport voice vlan 100

    Trying to achieve this scenario with a Cisco SG300 switch turns into a nightmare. You will have to deal with a Dynamic of VLAN voice Auto Voice VLAN mode. Then, you must have a configured trigger and activated Automatic Smartport . I tried to do this in CLI nothing helps. Cisco 7965 receives an IP address of the access VLAN on Gi15 interface, which is 101 VLAN. I need to receive an address IP of the VLAN 100.

    The current configuration under Gi15 interface is as follows:

    interface gigabitethernet15

    activate the storm control

    broadcast storm control level kbit/s 10

    Storm-control include multicast

    port security throw trap 60

    maximum port security by 10 points

    port security mode max-addresses

    spanning tree portfast

    LLDP-med disable

    switchport mode access

    switchport access vlan 101

    ! next order is internal

    macro auto smartport dynamic_type unknown $native_vlan 101 $voice_vlan 100

    Now, I don't know how the macro auto smartport dynamic_type unknown $native_vlan 101 $voice_vlan 100 command in the config, and I do not know how to remove it.

    When I try to enter the command macro auto smartport type ip_phone_desktop under Gi15 interface, I get the following error message:

    The $voice_vlan macro setting is not configurable by the user

    It seems that the auto attendant smartport macro ip_phone_desktop can not apply the setting $voice_vlan with a value of 100. In fact, I explicitly does not use this parameter to everything in the order of macro auto smartport type ip_phone_desktop ; However, the SG300 switch knows that the voice VLAN VLAN 100, and he's trying to use this VLAN ID as the value of the $voice_vlan parameter, the macro fails.

    I tried statically configure the voice VLAN on the switch SG300 using the command id of the vlan 100 voice , but I couldn't get the ip_phone_desktop macro to configure interface Gi15 correctly. Then, I removed the command id of the vlan 100 voice and obtained SG300 to learn his voice VLAN ID of UC560 connected to the SG300 through a trunk port based on the port configuration (connected to SG300) for the trunk of the next UC560:

    switchport trunk vlan 101 native

    switchport mode trunk

    switchport voice vlan 100

    Cisco-switch macro description

    This is the command switchport voice vlan 100 who announces to SG300 via CDP VLAN 100 is a voice VLAN. When I run the command show vlan local VoIP on the SG300, I get the following result:

    VLAN ID - VPT DSCP Source MAC address Interface

    1                    5          46       default           ----                    ---

    * 100 CDP e0:5f:b9:xx:yy:zz gi28

    Thus, it is clear that the SG300 receives information from UC560 via CDP in port Gi28 VLAN 100 is the voice VLAN. However, I can not always apply the ip_phone_desktop macro to SG300 Gi15 interface.

    Also, I tried to set up vState ofoithis vlan auto-déclenché as well as the commands in global configuration State vlan automatic voice activated mode. Or setting changes anything view voice VLAN announced at Cisco 7965 where Cisco 7965 continues to use VLAN101 (access the VLAN assigned to the interface Gi15).

    Hello telecastle,

    The Macro just get in the way most of the time. A default state on the switch a user will set the id of the vlan voice with orders

    (config) #voice vlan id 100

    * This will create the vlan 100

    VLAN, VoIP? * You can use to change your defaults for dscp and cos a long with all the other settings.

    State of vlan (config) enabled automatic #voice

    (config) #interface rank fa1-24

    (config-if-range) #switchport trunk vlan 101 native

    trunk (config-if-range) #switchport allowed vlan add 100

    * This function will define the vlan native on the trunk to 101 for the data port and vlan tagged will be 101 for the voice.

    CDP is enabled automatically and should learn the features of the phone and get on the phone to the vlan 101 on this port.

    CDP of the UC should automatically fill in the switch of the SG. You may need to upgrade the switch to the latest firmware however. Also make sure that the DHCP server for the voice if the CPU must be configured accordingly.

    Let me know if this helps.

    Cisco Small Business Support Center

    Randy Manthey

    CCNA, CCNA - security

  • Voice VLAN help please

    My client has 2 SG300 - 52p and 5 SG300 - 28 p. We have installed a VoIP telephony system earlier this year. At the time of installation, we placed the phone on the native VLAN 1 System. Now, they want to pass the phone system to a new VLAN, because their class C subnet is running out of addresses. DHCP is managed by their Active Directory and their router/firewall is a box to sort out. The SG300 switches have a basic configuration only.

    To move the phone system to a new VLAN, I created 20 VLAN on each switch. I then turned on VLAN auto voice. I have all the ports on each switch setting on the trunk. Computers are plugged into the back of the phone. I then created a virtual interface in the box to unravel for VLAN 20. Box unravel also manages DHCP to the new VIRTUAL LAN. Active Directory is always manage DHCP for VLANS native.

    I ping from each switch to the bridge of the new VLAN. Since each computer I can ping the gateway and on the new LAN VIRTUAL phone system. However, phones will not seize an address on the VIRTUAL LAN and when they have the static value, they cannot communicate with other devices on the VIRTUAL LAN.

    Any help would be much appreciated. I don't know what I'm on.

    Here is an example of part of a switch configuration to work with Zultys phones where voice VLAN is 100 and data VLAN 10:

    database of VLAN
    VLAN 10,20,100
    output
    ID of the vlan 100 voices

    interface fastethernet1
    Description "RCP and voice."
    switchport trunk allowed vlan add 100
    trunk switchport vlan 10 native
    !
    interface fastethernet2
    Description "RCP and voice."
    switchport trunk allowed vlan add 100
    trunk switchport vlan 10 native

    In your case, you need a trunk port with 20 VLAN Tag on your firewall (or an access port to a separate physical port on VLAN 20.  The default gateway served on the phone (or put statically) should be the interface on intellectual property.  Then, you can also allow routing inter - vlan for admin access or MXIE if you use.

    One thing to note on Zultys is by default I think the device profile disables LLDP, but on phones, it is enabled out of the box.  For the first time that a phone downloads its config from the Zultys it can turn of LLDP unless you have checked the box to keep it on.

  • No SG300-52 routing inter - VLAN

    Hello

    I have a base on this SG300-52 configuration:

    • L3 is enabled
    • Latest Firmware is installed (1.4.0.88)
    • Vlan1 IP is 10.0.0.1/24
    • A PC is connected to port 1 (with IP 10.0.0.3)
    • VLAN99 IP is 192.168.0.2/29
    • A router is connected to the 49 port (with the 192.168.0.1 IP address and Internet access to the router is OK)
    • On SG300-52 default gateway is 192.168.0.1

    The SG-300:

    • I can ping the default gateway (192.168.0.1) and any Internet address, using 192.168.0.2 as address IP Source
    • I can't ping the default gateway (192.168.0.1) or any Internet address, using 10.0.0.1 as address IP Source
    • I can ping my PC (10.0.0.3), using 10.0.0.1 as the IP Source address
    • I can't ping my PC (10.0.0.3), using 192.168.0.2 as address IP Source

    There is no routing inter - VLAN, but I can't find how to activate...

    The complete configuration is the following:

    #show run SG300-52
    config-file-header
    SG300-52
    v1.4.0.88 / R800_NIK_1_4_194_194
    CLI v1.0
    router adjustment system mode

    SSD of encrypted file indicator
    @
    SSD-control-start
    config of SSD
    control of password file unrestricted SSD
    no control of the integrity of the file ssd
    SSD-control-end cb0a3fdb1f3a1af4e4430033719968c0
    !
    database of VLAN
    VLAN 99
    output
    Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
    Add a voice vlan Yes-table 00036 b Cisco_phone___
    Add a voice vlan Yes-table 00096e Avaya___
    Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
    Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
    Add a voice vlan Yes-table 00d01e Pingtel_phone___
    VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075
    Add a voice vlan Yes-table 00e0bb 3Com_phone___
    Hello interface range vlan 1
    hostname SG300-52
    username privilege 15 c464af817287343305cbd6493c593885695df531 encrypted password cisco
    property intellectual ssh server
    Server SNMP Server
    The telnet server IP
    !
    interface vlan 1
    the IP 10.0.0.1 255.255.255.0
    no ip address dhcp
    !
    interface vlan 99
    name WAN
    IP 192.168.0.2 255.255.255.248
    !
    interface gigabitethernet49
    switchport mode general
    VLAN allowed switchport General add 99 unidentified
    switchport General pvid 99
    !
    output
    Default IP gateway 192.168.0.1

    You have an idea on the issue?

    Thanks in advance for your help.

    Hi Anthena1390

    My email is [email protected] / * /. When you reply to the email can let me know which devices need to communicate on VLAN 99. Is there a major reason for SG300 happen DHCP assumes that your router? Well I would like to add a few screenshots, they will show you how to properly set up a P2p link, assign DHCP pools, how to correctly add default routes. Send an email and lets get your problem is resolved.

Maybe you are looking for

  • screenshot does not not since the iOS 10 update

    Everyone has noticed that the screen capture function seems to be hit and Miss since the iOS10 upgrade. Have noticed this on ipad and iPhone 6, a reboot seems to fix it for a while, but then comes back. The ipad seems to have more problems than iPhon

  • Envy 15 - no audio can be heard, despite the mixer volume showing activity.

  • Satellite A30 start question

    When I start my laptop, I get a windows with "RUNDLL" error message in the title of the box and it says "error loading C:\WINDOWS\Downloaded program Files\bridge.dll can not specified Module"-what this means and how do I get rid of him? I tried to re

  • Side-By-Side errors on 99% of the programs... I need help!

    Two nights ago, I turned off my computer and let it install the updates as she did. Windows update history lists as follows: Tool to remove malware Windows x 64-may 2009 (KB890830)Update definition for Windows Defender - KB915597 (definition 1.57.132

  • in offline mode

    M y printer was working fine until my service provider came to plu and modified on the modem. Not my printer says it is offline. The tech has left me with a wireless name and a password. I do not use it wireless. There is a phone cord entering the mo