Help with 1921 SRI Easy VPN remote w / Easy VPN Site-to-Site access

Similar Questions

• Need help with configuration on cisco vpn client settings 1941

  Hey all,.

  I just bought a new router 1941 SRI and need help with the configuration of the parameters of the VPN client. Orders aspect a little different here, as I'm used to the configuration of ASA and PIX for vpn, routers not...

  If anyone can help with orders?

  I need the installation:

  user names, authentication group etc.

  Thank you!

  Take a peek inside has the below examples of config - everything you need: -.

  http://www.Cisco.com/en/us/products/ps5854/prod_configuration_examples_list.html

  HTH >

  Andrew.

• Help with customer 501 pix for the configuration of a site...

  Hello everyone, I am trying to set up a customer vpn site and after a few days

  I'm at the end of the roll.

  I'd appreciate ANY help or trick here.

  I tried to set up the config via CLI and PDM, all to nothing does not.

  Although the VPN client log shows the invalid password, I am convinced that the groupname password is correct.

  I use the Cisco VPN Client 5.0.07.0290 v.

  -----------------------------------------------------------------

  Here is HS worm of the PIX:

  Cisco PIX Firewall Version 6.3 (5)
  Cisco PIX Device Manager Version 3.0 (4)

  -----------------------------------------------------------------

  Here's my sh run w / passwords removed:

  pixfirewall # sh run
  : Saved
  :
  6.3 (5) PIX version
  interface ethernet0 10baset
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate the encrypted password to something
  that something encrypted passwd
  pixfirewall hostname
  domain ciscopix.com
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol they 389
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list ping_acl allow icmp a whole
  permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 192.168
  . 50.48 255.255.255.248
  outside_cryptomap_dyn_20 ip access list allow any 192.168.50.48 255.255.255.248

  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside pppoe setroute
  IP address inside 192.168.1.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  IP local pool vpnpool 192.168.50.50 - 192.168.50.55
  history of PDM activate
  ARP timeout 14400
  Global interface 10 (external)
  NAT (inside) 0-list of access inside_outbound_nat0_acl
  NAT (inside) 10 0.0.0.0 0.0.0.0 0 0
  Access-group ping_acl in interface outside
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20
  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value
  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
  outside_map interface card crypto outside
  ISAKMP allows outside
  part of pre authentication ISAKMP policy 20
  ISAKMP policy 20 3des encryption
  ISAKMP policy 20 md5 hash
  20 2 ISAKMP policy group
  ISAKMP duration strategy of life 20 86400
  vpngroup address vpnpool pool vpnaccessgroup
  vpngroup dns 192.168.1.1 Server vpnaccessgroup 192.168.1.11
  vpngroup wins 192.168.1.1 vpnaccessgroup-Server
  vpngroup vpnaccessgroup by default-field local.com
  vpngroup idle 1800 vpnaccessgroup-time
  something vpnaccessgroup vpngroup password
  Telnet 192.168.1.0 255.255.255.0 inside
  Telnet timeout 60
  SSH 192.168.1.0 255.255.255.0 inside
  SSH timeout 5
  Console timeout 0
  VPDN group pppoe_group request dialout pppoe
  VPDN group pppoe_group localname someone
  VPDN group ppp authentication pap pppoe_group
  VPDN username someone something
  dhcpd address 192.168.1.100 - 192.168.1.110 inside
  dhcpd dns 206.248.154.22 206.248.154.170
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  Terminal width 80
  Cryptochecksum:307fab2d0e3c5a82cebf9c76b9d7952a
  : end

  -----------------------------------------------------------------------------------------------

  Here is the log of pix in trying to connect with the client vpn cisco w / real IPs removed:

  crypto_isakmp_process_block:src: [cisco vpn client IP here], dest: [cisco PIX IP here] spt:64897 TPD:
  500
  Exchange OAK_AG
  ISAKMP (0): treatment ITS payload. Message ID = 0

  ISAKMP (0): audit ISAKMP transform 1 against 20 priority policy
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 2 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 3 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 4 against 20 priority policy
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 5 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform against the policy of priority 20 6
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform against the policy of priority 20 7
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 8 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 9 against priority policy 20
  ISAKMP: 3DES-CBC encryption
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP (0): atts are not acceptable.
  crypto_isakmp_process_block:src:src: [cisco vpn client IP here], dest: [cisco pix IP here] spt:64897 TPD:
  500
  ISAKMP: error msg not encrypted
  crypto_isakmp_process_block:src: [cisco vpn client IP here], dest: [cisco pix IP here] spt:64897 TPD:
  500
  ISAKMP: error msg not encrypted
  pixfirewall #.

  ---------------------------------------------------------------------------------------------------------------

  Here is the log of the vpn client:

  363 16:07:58.953 01/07/10 Sev = Info/4 CM / 0 x 63100002
  Start the login process

  364 16:07:58.953 01/07/10 Sev = Info/4 CM / 0 x 63100004
  Establish a secure connection

  365 16:07:58.953 01/07/10 Sev = Info/4 CM / 0 x 63100024
  Attempt to connect with the server '[cisco pix IP here]. "

  366 16:07:58.953 01/07/10 Sev = Info/4 IKE / 0 x 63000001
  From IKE Phase 1 negotiation

  367 16:07:58.969 01/07/10 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) [cisco pix IP here]

  368 16:07:59.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700008
  IPSec driver started successfully

  369 07/01/10 Sev 16:07:59.078 = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  370 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000014
  RECEIVING< isakmp="" oak="" ag="" (sa,="" vid(xauth),="" vid(dpd),="" vid(unity),="" vid(?),="" ke,="" id,="" non,="" hash)="" from="" [cisco="" pix="" ip="">

  371 16:08:00.110 01/07/10 Sev = WARNING/3 IKE/0xE3000057
  The HASH payload received cannot be verified

  372 16:08:00.110 01/07/10 Sev = WARNING/2 IKE/0xE300007E
  Failed the hash check... may be configured with password invalid group.

  373 16:08:00.110 01/07/10 Sev = WARNING/2 IKE/0xE300009B
  Impossible to authenticate peers (Navigator: 915)

  374 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK INFO (NOTIFY: INVALID_HASH_INFO) [cisco pix IP here]

  375 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK INFO (NOTIFY: AUTH_FAILED) [cisco pix IP here]

  376 16:08:00.110 01/07/10 Sev = WARNING/2 IKE/0xE30000A7
  SW unexpected error during the processing of negotiator aggressive Mode:(Navigator:2263)

  377 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000017
  Marking of IKE SA delete (I_Cookie = A152D516B07D9659 R_Cookie = 5F4B55C38C0A40F4) reason = DEL_REASON_IKE_NEG_FAILED

  378 16:08:01.078 01/07/10 Sev = Info/4 IKE/0x6300004B
  IKE negotiation to throw HIS (I_Cookie = A152D516B07D9659 R_Cookie = 5F4B55C38C0A40F4) reason = DEL_REASON_IKE_NEG_FAILED

  379 16:08:01.078 01/07/10 Sev = Info/4 CM / 0 x 63100014
  Could not establish the Phase 1 SA with the server "[cisco pix IP here]" due to the "DEL_REASON_IKE_NEG_FAILED".

  380 16:08:01.078 01/07/10 Sev = Info/4 IKE / 0 x 63000001
  Signal received IKE to complete the VPN connection

  381 16:08:01.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  382 16:08:01.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  383 16:08:01.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  384 16:08:01.078 01/07/10 Sev = Info/4 IPSEC/0x6370000A
  IPSec driver successfully stopped

  Mmmm... What version of vpn client do you use?

  If you use the last being, it looks like you might have it downgrade to a version older than the version of your PIX is old enough.

• AnyConnect VPN connection VPN site access to remote site

  I need our VPN users to gain access to our remote site (Site to Site VPN), there is no problem to access the main site through the VPN. Crypto map sites have the VPN pool in the card encryption.

  Any ideas?

  Here is the main Site (ASA5520) config inside 192.168.50.0

  crypto_vpn_remote-site access-list extended ip 192.168.50.0 allow 255.255.255.0 172.16.1.0 255.255.255.0

  IP 192.168.99.0 allow Access-list extended site crypto_vpn_remote 255.255.255.0 172.16.1.0 255.255.255.0

  inside_nat0_outbound to access extended list ip 192.168.50.0 allow 255.255.255.0 172.16.1.0 255.255.255.0

  access extensive list ip 192.168.99.0 inside_nat0_outbound allow 255.255.255.0 172.16.1.0 255.255.255.0

  Remote site (PIX 515E) inside 172.16.1.0

  access-list crypto_vpn_main-site permit ip 172.16.1.0 255.255.255.0 192.168.50.0 255.255.255.0

  access-list crypto_vpn_main-site permit ip 172.16.1.0 255.255.255.0 192.168.99.0 255.255.255.0

  access-list sheep permit ip 172.16.1.0 255.255.255.0 192.168.50.0 255.255.255.0

  access-list sheep permit ip 172.16.1.0 255.255.255.0 192.168.99.0 255.255.255.0

  VPN (AnnyConnect) 192.168.99.0

  On the main site, pls make sure that you have 'same-security-traffic permit intra-interface' active.

  Also, if you have split tunnel configured, please also make sure that he understands the Remote LAN (172.16.1.0/24).

  Hope that helps.

• Need help with attention not approved VPN server certificates.

  I've been on the many other posts about it, and they all seem a bit different, so I started my own thread.

  I was sent to my users via the ASA AnyConnect 3.1.02026, and we all get the warning of the Cert of untrusted when connecting VPN server.

  When the ASA deploys the client, it puts the external IP of the SAA as the host name, which causes the error.

  So I have two questions: 1. How can I get the ASA to make host name "vpn.cfo.com" when a user installs the client and 2. How can I change my cert so that it does not show the internal name of the ASA and use 'vpn.cfo.com' instead?

  Here are all the news that everyone should not (I) help to think

  SSL-trust ASDM_TrustPoint0 OUTSIDE_PRIMARY point

  Certificate

  Status: available

  Of the certificate number:

  Use of certificates: Signature

  Public key type: RSA (1024 bits)

  Signature algorithm: SHA1 with RSA encryption

  Name of the issuer:

  hostname = ambossfw01.cfopub .net

  CN = ambossfw01

  Name of the object:

  hostname = ambossfw01.cfopub .net

  CN = ambossfw01

  Validity date:

  start date: 15:17:42 EDT June 2, 2011

  end date: 15:17:42 EDT May 30, 2021

  Trustpoints Associates: ASDM_TrustPoint0

  CA

  Status: available

  Of the certificate number:

  Certificate use: general use

  Public Key Type: RSA (2048 bits)

  Signature algorithm: SHA1 with RSA encryption

  Name of the issuer:

  CN = VeriSign Class 3 Public Primary Certification Authority - G5

  or = (c) 2006 VeriSign\, Inc. - authorized only use

  OU = VeriSign Trust Network

  o = VeriSign\, Inc.

  c = US

  Name of the object:

  CN = VeriSign Class 3 Secure Server CA - G3

  OU = terms of use at https://www.verisign.com/rpa (c) 10

  OU = VeriSign Trust Network

  o = VeriSign\, Inc.

  c = US

  OCSP AIA:

  URL: http://ocsp.verisign.com

  CRL Distribution points:

  [1] http://crl.verisign.com/pca3-g5.crl

  Validity date:

  start date: 19:00:00 EST February 7, 2010

  end date: 18:59:59 EST February 7, 2020

  Trustpoints Associates: _SmartCallHome_ServerCA

  Any help would be greatly appreciated.

  Hello

  Cisco has made a strict checking of KU and EKU in recent versions of AnyConnect, which leads to the warning you got.

  To my knowledge, if you go to 3.1.00495, you will not get this warning, if not, you need to get the valid KU and EKU fields in your certificate of ASA.

  To use specific trustpoint, please check the 'truspoint ssl' command in global configuration mode.

  Mashal

• Help with motion 3D 'easy '.

  I was looking for a certain media STASH and I came across what I thought was an animation EASY to practice, reproduction, well at least the first half of it.

  It seemed that the entire animation could be done in AE.

  It begins with a triangle, representing razor, reveal themselves as he slots through the black bottom, cut a slot in the screen to reveal a white vertical opening.  The knife retracts and the slot/opening widens as if it were an elevator door.  She opens a shadow is projected on the black door.  The door/shadow turns a bit and starts to move off the screen to the left as new doors/shadows come on the right screen.  The shadow has the perspective.

  What I was trying to figure out this simple must dismiss 2 hours.

  While the doors/shadows continue the camera angle turns and they become one like streetlights, in the opposite direction, forming a tunnel.  The camera passes over them, and he becomes the white markings on the road.

  I had jumped the sharing knife/razor because I thought it looked very easy to recreate. Either a fixed image of the triangle revealed by a mask or creation of a solid gray and ever-changing shape of mask to reveal and hide.

  The crack, I created by a white, size of the layer, solid and creating a retangle mask.  The shape of the mask is developing to increase the length of the slot, then widens to be like opening the door.

  I moved the anchor to the bottom of the rectangle, made the 3D layer, it reproduces and he turned on his "Orientation" 90 degree X and Z of 56 degrees.  I don't think that it was absolutely necessary to chang the anchor point. Also I don't understand why I have the Z was to be moved 56 degrees is looks like the number would have been 60 degrees but that leaves a small space on the edge.  But when I tried to extend to the shadow on the right side of the screen that does not stretch.  So I had to increase the solid layer shadow size - much.

  Make a 50 mm camera and a null object is the parent of layers worn and shadow.  (And working with these tools of camera is a TRIP alone!)

  Finally got the shadow on the lower right corner, but it was not the perspective on its own.  So I made a point of view by changing the shape of the mask.

  I don't know maybe that this was created with the help of a solid and 3D lighting to create the shadow of the door.

  The film is to:

  http://www.Sehsucht.de/page/work/

  its in the 2nd column and its called "FLIMFEST HAMBURG 2005.  The screenshot looks like a train in space.

  a link to a tutorial or anything like that will be most appreciated.

  Thank you

  Cree

  Don't overdo. Pass a single program to sink in a little bit first prior to new pastures. more you try to do at the same time, it will get more confusing. Blender is of course a natural candidate, if you don't want to spend the money. A very affordable choice would be Cheetah3D, which mimics a little a lot of what Cinema4D , at a fraction of the price. Certainly enough for especially stylized output such as common in parts graphics motion.

  Mylenium

• Please help with my password. After trying to connect using a mobile phone, access has been denied. Saying: my account has been blocked

  original title:

  Finally, I registered my account some time in August, 2010. I noticed that when I tried to sign new after trying to connect using a mobile phone, has been denied access. Saying: my account has been blocked because I tried o identify you on several occations. My pin code is * and my email is * address email is removed from the privacy * help me with my password recovery I did not had access to my account for some time. Thank you and God bless you!

  Hello

  you ask about Hotmail?

  If so, we can help you not in these responses Vista Forums

  Please repost your question in hotmail in the hotmail link below forums

  http://windowslivehelp.com/product.aspx?ProductID=1

  Forums

  E-mail client and the appliance issues

  Hotmail Sign In questions

  Lost or deleted emails

  People and Contacts

  Reading, writing, and formatting mail

  Sending and receiving mail

  Sign in, and sign to the top and account security

  Using the Hotmail calendar

  Using Web Messenger

   

   

  Consult with Microsoft Certified Solutions

  How to work the views Active Hotmail?

  Your account has been temporarily blocked

  What to do if you can't connect to Windows Live Hotmail

  Compromised account - unauthorized account access

  Reset your Windows Live ID password

  Error when you try to send an e-mail: your message seems to have triggered our spam filters.

  Change your Windows Live ID password

• Help with a stream of e-mail for clients Web sites

  What do people use Blasts of e-mails for customer Web sites? Most of my potential customers want to collect email addresses and send monthly emails.

  Don't know where to start any suggestions would be appreciated. I'm still learning html slowly...

  Hello

  I believe you are referring to emailing campaigns.

  If you are hosting the site on the external server, you can use any email marketing service like mailchimp, Campaign monitor, brain etc. by e-mail.

  and if you are using Business Catalyst to host your site, then you will benefit from end of BC's email marketing service.

  British Colombia, you will need to create the e-mail configuration settings and the mailing list that includes the e-mail address of receivers.

  There are other features that you can use, detailed explanation:

  http://helpx.Adobe.com/business-catalyst/SBO/email-campaigns.html

  http://www.BusinessCatalyst.com/BC-blog/video_getting_started_with_the_new_email_marketing _enhancements

  http://www.BusinessCatalyst.com/features/email-marketing

  Thank you

  Sanjit

• Need help with query between 2 dates

  Hello

  I did not SEE in a long time and need help with a simple query.

  I have a table of DB access with 3 fields, name, date and number

  What I want is to create a query to retrieve all the names between 2 dates

  When I ask the date field, the results are showing in this formats 2013-07-12 00:00:00

  Here's my query

  < cfquery datasource = 'mydb' name = 'test' >

  SELECT name from myTable

  where edate between ' 2011-01-01 00:00:00 ' AND ' 2013-01-01 00:00:00 '

  < / cfquery >

  < cfoutput query = 'test' >

  #name #.

  < / cfoutput >

  What I get is this error

  ODBC = 22005 (assignment error) error code

  [Microsoft] [ODBC Microsoft Access driver] Type mismatch of data in the expression of the criteria.

  Don't know what I'm doing wrong here.

  Please let me know.

  Thank you

  SELECT ename

  FROM MyTable

  WHERE edate BETWEEN

  AND

  #ename #.

• Help with VPN site-to-site under another VPN

  Hello guys,.

  I need a help to this scenario.

  Branch--> HQ--> Remote Site, where:

  Branch: Internal = 192.168.50.0/24

  HQ: Internal = 192.168.40.0/24

  Distance from the site = 10.175.26.0/24

  Branch HQ plus the two ASA with ESP-3DES-MD5. (Here, we use the actual LAN IP range for field of encryption)

  HQ + remote place = my side ASA with ESP-AES-256-SHA. (Here, to reach the Remote Site 10.175.26.0/24 we are NAT our LAN IP range at 172.18.0.10, so the field of encryption is 172.18.0.10--> 10.175.26.0/24)

  Now we have this branch reachs the Remote Site, under the VPN with branch HQ HQ at Remote Site.

  My actions:

  Directorate-General for the firewall:

  -In the VPN Site to Site configuration, I added the 10.175.26.0/24 of the tunnel between the branch and the headquarters of the remote network.

  -J' added the EXEMPTION for 10.175.26.0/24 inside.

  HQ of firewall:

  -In the VPN Site to Site configuration, I added the 10.175.26.0/24 of the tunnel between the branch and the headquarters of the remote network.

  -J' have created a dynamic policy outside source = IP range of branch to Remote Site IP range = translated into 172.18.0.10.

  I already work for another Remote Site, but that the other has proposal IPsec ESP-3DES-MD5. (the same branch) I don't know if this is the problem, but I tried to use two proposal together, 3DES-MD5 and SHA-256-AES.

  Firewall rules are ok too.

  Where is the error in this configuration?

  Thank you

  Diego

  good

  be solved in this post

• help with 2 concurrent internal users trying to VPN (Cisco s/w) at extern

  Hi all

  We are a small office running Small Business Server 2003 - which means that we miss the ISA 2004 firewall.

  An external company provided us with the Cisco VPN (ver403a) software to access their site web network / secure.

  One user could connect to the network of the company for some time. It was working fine until two users tried to connect at the same time - using the same VPN user ID. We have learned by the company that it should work, but it just isn't so we asked a second VPN user ID to test with.

  Now what happens is that the user has to connect with success and user B can connect successfully at the same time however even if user B is connected, and you see even an IP assigned to the VPN adapter, the user can not ping the company website and then of course can not access it. Very strange indeed!

  I went back to the company and told her about our dilemma and we were told that there is nothing at their end, but a problem of Routing/NAT at our end. So here, I'm now looking for help I hope that some experts from Cisco. :-)

  Appropriate, the ports were opened in ISA and once again the two users will connect to the VPN very well, it's just that the second user can? t go further.

  It was suggested to me that is maybe not a routing problem, but that Cisco VPN server/box the company rejects the second connection because it comes from the same IP address - that would be the IP address of our ISA Server external network card.

  If anyone has any suggestions on how to solve this problem, I would be so grateful!

  Thank you very much.

  Tammy

  VPN configuration multiple tunnels for the same device (same public IP address) is not possible because it is not possible to have several (SA) IPsec Security Association for the same position. However, it is possible to configure multiple VPN tunnels to multiple devices. In your case, if your client PC using public IP addresses, they both can simultaneously connect to the remote vpn server. However if you are using a single public IP address so it is not possible to have mutiple vpn connections. If you have only a single ip address of your ISP then it would have to do PAT and you will be not able to have the two vpn clients to connect to even

  time.

• Need help with the port forwarding for a XBox remote Streaming

  I have a router R6200v2 and need help with port forwarding.

  I came across this set of instructions for setting up stream port forwarding XBox remotely from anywhere

  http://kinkeadtech.com/2015/07/how-to-stream-Xbox-one-to-Windows-10-from-anywhere-with-Internet/

  I have no idea when it comes to such things and I want to make sure I do it correctly without messing up my existing home network.

  Port Forwarding and triggering Port pages setup look very different from what the guy uses. Can someone walk me through what I do to set up please?

  Hi @varxtis,

  You must enter them in the field for a start external Port and external completion Port. You will need to send individually except for the range of 49000-65000. The steps are as follows.

  1. create a Service name (it could be something else that you cannot use the same service name twice. Ex. XBOX1, XBOX2 and so forth.)

  2. Select the type of service (TCP, UDP or both)

  3 entry 5050 times a start external Port and external endpoints.

  4. Select the IP address of your XBOX.

  5. Select apply.

  6 do the same for other port numbers. To the beach, use 49000 for the external departure Port and for the external completion Port 65000.

  Kind regards

  Dexter

  The community team

• Helps with the rv180w and the Shrew soft vpn

  Hi, I'm trying to establish a vpn connection by using soft shrew for the cisco rv180w router.

  I watch and read everything I could find, but the connection drops during the opening of the tunnel.

  There were a few tuttorial here in the forum, but the links are down.

  I want Edifier is to establish communication and to be able to access my domain on the network.

  Any help with the settings would be greatly apeciated. I am new to vpn.

  Thanks in advance.

  Federico,

  Try to access the following link. It has good instructions for a similar model. The main difference is that the SA500 has double-WAN and the RV180W does not work.

  https://supportforums.Cisco.com/docs/doc-9378#comment-7216

  Here's another tutorial for the RVS4000 that can help:

  https://supportforums.Cisco.com/docs/doc-18443

  Check out the last post in the following thread, which received instructions for the RV220W (should be exactly the same as RV180W)

  https://supportforums.Cisco.com/message/4165652#4165652

  -Marty

• Need help with native VPN client for Mac to the Configuration of the VPN router RV082

  Guys,

  I am trying to set up router RV082 VPN Client with native Mac for my remote access. However, no matter what I did, I'm not able to make works. Can any give me an example of how to set my router RV082 and Mac Book Pro (Mountain Lion)?

  Thank you

  Hi Jixian, the native client MAC does not work. The IPSEC VPN client is the same as the 5.x Cisco VPN client is not supported on this device.

  Your alternatives are to use PPTP or a 3rd party IPsec client such as ipsecuritas.

  -Tom
  Please evaluate the useful messages

• Need help with VPN (Cisco831 + ASA5510)

  Hello

  We are trying to set up a VPN site-to site between a Cisco831 and an ASA5510.

  I have attached two units configuration files and file of the SAA.

  on the 831, we get:

  KED1CSPSVPNr01 #.

  * 19 Mar 22:17:48.743: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode failed with the peer to 8.10.15.130

  I can't figure out where the problem. Could someone help please?

  Thank you.

  try to add to the ASA...

  card crypto outside_map 1 set pfs