Hibernation problems - my computer turns off but it restarts immediately.

Similar Questions

• 2-3 days after the expiry of my warranty of one year, my computer turns off suddenly during use. I rebooted, but it stopped again.

  2-3 days after the expiry of my warranty of one year, my computer turns off suddenly during use.  I rebooted, but it stopped again.

  The model is that the computer runs for 15-30 minutes, then suddenly stops, the system reboots, runs for 2-3 minutes, stops, restarts, spans less than a minute, stops, restarts, stop after a few seconds, etc., and at that time there I give until the next day when I repeat the same cycle all over.    I have Windows Vista Home Premium 32 bit and it is a model of Dell Inspiron 518.  There is no error message but a beep at startup upward.  I ran Windows repair program 'Start' who did a restore without success.  The problem occurs even in Safe Mode.

  Does anyone have a guess as to what is the diagnosis?  Thank you.

  Hello

  Could be hardware or even heat and ventilation the related. Try using a small fan to increase ventilation. When a PC
  Remove ALL power and reinstall the memory, all cards and cables (do just not shake - remove and replace-)
  cables on both ends where possible).

  As it does in Mode safe so you probably need technical support in a real store of the computer - no Peeks/leeks at BestBuy or other large shopping areas. Very difficult to solve if it does not remain under tension.
  It remains under tension if you start from the disc of Vista?

  -----------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on these reboots.

  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  -------------------------------------------------------------------------
  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
  information on all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• my computer turns off not and the hibernation...

  my computer turns off not and the hibernation...

  Hello

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then run checkdisk - schedule it to run at the next startup, then apply OK your way out then
  turn it back on.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  The above is kind of prerequisites and may solve the problem.

  ==========================================

  A Fixit for Hibernate

  How can I enable hibernation on my Windows Vista computer?
  http://support.Microsoft.com/default.aspx/KB/929658

  How to reactivate the lack of Hibernate Option in Windows Vista?
  http://www.askvg.com/how-to-re-enable-missing-Hibernate-option-in-Windows-Vista/

  -------------------------------------------

  More if necessary:

  Check your settings (BIOS/CMOS) - usually F2 as you start - Wake on Lan, Wake on Modem
  and so on.

  Troubleshooting Windows Vista sleep and extended
  http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
  http://support.Microsoft.com/kb/950686

  May need to reset all to default power settings and then place back as you prefer.

  How to solve a problem of Mode for Vista and find a Solution
  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Panel configuration-Device Manager - look at the settings for the WiFi network card power management,
  Modem and other devices. (Double click on the device and the power management tab)

  May need to reset all to default power settings and then place back as you prefer.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• computer won't goto sleep IE screen turns off but the hard drives will not be

  No matter what I put in power options, the computer won't go to sleep.

  The monitor turns off but the hard drives, fan to continue working.

  I can't force the drives to put beyond the control of the characteristics to uncheck in the power options.

  The computer turns off when the power off but sleep option does not work.

  Thanks for any help.

  Hello

  Thanks for posting your question on the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the question and your efforts to resolve.

  This problem may be due to the following reasons:

  -The drivers are not updated.
  -Power option settings are incorrect.
  -The devices connected to the computer are preventing it from going into standby mode.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run Troubleshooter of power and control.
  Reference:
  Open the troubleshooter of power
  http://Windows.Microsoft.com/en-us/Windows7/open-the-power-Troubleshooter

  If this does not help, use method 2.

  Method 2:
  Please use the suggestions in this article and check the issue.
  Reference:
  Windows 7 is not going to sleep
  https://Support2.Microsoft.com/kb/976877

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• My wireless connection turns off when I restart my computer.

  My Internet AT & T Uverse vendor sent me an adapter for my HP Compaq Presario windows XP computer's free wireless. However, once I installed it, it turned off everytime I restarted my computer. AT & T Uverse Tech Support says that it wasn't a problem with the software, but they can not help me with the settings on my computer. I tried everything I know to do the work of Wi - Fi, but no avail. Can someone help me? I'm at my wits end. Thank you!

  Hey Steve,

  What type of wireless network card did give you?
  It is a usb adapter and if so, what brand is it?
  You use the Windows XP Wireless Manager or software that has been installed with the adapter?
  It sounds like a problem with your wireless Manager did not remember network you connected to.
  I suggest to uninstall all software provided with your card and using only the Windows wireless:
  http://support.Microsoft.com/kb/870702
  I hope this helps.

• Why my internet accounts automatically get disconnected after that my computer turns off by itself?

  I have a Compaq PC with processor Dual-Core AMD Athlon X 2 5000, and it runs Windows Vista Edition Home Premium... In my view, that is running Service Pack 2. I use the computer to check my e-mail, my YouTube and Facebook accounts (and possibly other accounts spread I connect to).

  I usually use Internet Explore to browse the web. Sometimes my computer turns off by itself due to overheating. But whenever when this happens, when I turn my computer back on and return to the use of the Internet, I've totally frustrated to find that all my accounts were automatically disconnected!

  Even when I check these boxes to keep me connected to these accounts when I turn on the computer again after a successful stop, my accounts still get disconnected!

  It only seems to happen when my computer turns off by itself without stopping... mainly due to overheating. When I turn on the computer again after a successful regular stop, my accounts are automatically saved on once again, due to activate me "Keep me connected" by checking these little boxes. But after a situation when the computer is off all the time (either by himself for a reason, either by me with strength to turn it off when my computer crashes), my accounts do not remain.

  How can I prevent my accounts automatically be disconnected so that whenever I start the computer, after it turns off by itself, my internet accounts turned on? There must be a patch for this embarrassing situation here on the internet.

  Perhaps because an improper shutdown / forced can inpact on different parameters.

  Your must not PC in all cases be having heat problems, you need to fix this (heat) before it turns into something terminal

• computer turns off for no apparent reason. It's all a few minutes using Windows Vista Home Premium SP 2

  Every few minutes the computer turns off. No warning, nothing. It will restart ok, but stops then off again in a bit.

  I can be in the workplace, and it will cut offf.

  I'm usting Vista Home Premium SP2 version.

  Any Suggestions?

  Hello

  1 did you changes to the configuration of the system before the show?
  2. you receive an error message/code when the computer shuts down?
  3 does the computer automatically restart once it stops?
  Event Viewer
  
   
  You can check the event viewer to discover events that could cause this problem.
  See the link below to open the event viewer:
  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer
  For more information on what information appears in Event Viewer, see the link below:
  Disable automatic reboot manually.
  1. Right click on computer
  2. Properties
  3. Advanced system settings
  4. Startup and recovery
  5. Uncheck automatically restart.
  Resolution:
   
  Step 1:
   
  Safe mode
   
  Start the computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode
   
  Step 2:
  Clean boot
   
  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.
   
  See the following article in the Microsoft KB for more information on how to solve a problem by performing a clean boot in Windows Vista or Windows 7:
   
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135 
   
  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.
   
   
   

• Computer turns off automatically

  Hello

  my Windows Vista laptop turns off automatically. This isn't a standby automatic regular, Hibernate or shutdown. The computer will just empty. When you try to turn it back on, the message that "the computer was not properly extinguished" sometimes appears.

  This auto disable happens irregularly. Sometimes it seems to happen more often when the computer made the task more or heavier. But the computer seems to be overheating.

  Someone has an idea what could be the problem and I can try to do about it?

  GRT, M

  Suggestions only. I may be far away...

  1. If this problem started not more than 10-15 days ago, and if you remember a time when you did not have this problem, please do a system restore. Choose a 'good' day as your restore point.

  Start button > Search box, type system restore > press the Enter key > uac prompt > click on choose a different restore point > next > select dates as your restore point, until the click > next > finish
  To sit and wait. The machine restarts when it's done.

  Note: In most cases, do it in safe mode system restore is more preferable.
  Here's how to get safe mode:

  Shut down your computer > turn it back on and immediately and repeatedly tab key F8 until you see a black and white screen. The top/down arrow and select Safe Mode.

  2. If it is not an option, going to Safe Mode > selectlast known good Configuration and run it.

  
  t-4-2

• When I pick up my Windows 7 Acer Aspire power, the computer turns off when the battery shows fully charged

  I HAVE A CHILD OF 1 YEAR ACER ASPIRE WITH WINDOWS 7, WHICH IS CONNECTED TO BE WIRELESS. BUT WHEN I GET MY COMPUTER TURNS OFF THE POWER SUPPLY CORD. THE BATTERY SAYS FULLY CHARGED. IT WORKED AND NOW IT WONT. SOMEONE CAN ME SAY WHAT THE PROBLEM IS. I EVEN WENT BACK THROUGH HIM WITH DEFAULT AND IT DID NOT HELP.

  Hello

  Are you aware of any changes made to the computer, before the show?

  I suggest to change the power management and check for the issue.

  Change, create, or delete a power plan (scheme)

  http://Windows.Microsoft.com/en-us/Windows7/change-create-or-delete-a-power-plan-scheme

  If the above does not help, I suggest you to contact Acer support for assistance.

  http://support.Acer.com/us/en/default.aspx

  I hope this helps.

• I stop using the computer for a few minutes. Then the screen of the computer turns off. Its does not sleep I need to turn off the computer then put into market and re - turn on the computer.

  If I have not used the computer for a few minutes then the screen of the computer turns off. The computer is not sleep. I tried to use the space bar to wake him but he won't answer.  I have to turn off the computer. Then turn on the computer. This has happened for 2 months. I have a Dell DM051, 446 GB HDD with 329 free GB, 2 GB RAM, Intel (r) Pentium (r) CPU 2.80 GHz, ASUS A7 Series 240 and Windows 8 Pro graphics. I replaced the graphics card because I thought that this could be the problem, but it wasn't. I need to replace to fix this? Thanks for your help.

  You have disabled things like Hibernate and hybrid sleep, etc. on the power options screen in Windows?

  Have you checked the USB settings in the Device Manager? Search tab power management for each listed root USB hub and uncheck the box "allow the computer to turn off this device...". »

  And do the same for entries under Human Interface Devices (HID) device as Manager.

  Then restart...

• On the start with progress bar page, after that it becomes a little more than half, the computer turns off.

  MY MacBook Pro is frozen and I had to turn off get out of the frozen page and when I pressed the button to turn it on it makes the departure noise and then the progress bar lights. When it becomes a little to Midway, the screen goes black and the computer turns off.

  The progress bar that starts from the left end appears when your startup disk is too damaged to mount. The illustrious progress is the functioning of the equivalent of disk utility (ERD). He is never more than half before taking a decision.

  If your drive CAN be mounted, start-up continues normally.

  If your drive cannot be mounted, your Mac stops, because there is nothing productive that it can do.

  If your Mac is trying to start and crashes, which can produce always different results, but that doesn't seem to be the case here.

  I recommend that you start in recovery and run utility disk (ERD) until it comes clean or is hopelessly.

• My computer turns off during an update to windows xp and now windows xp will not load.

  My computer turns off during an update to windows xp and now windows xp will not load.  It gives me the option of last known good configuration and safe mode startup and normal startup, but it just goes back to the loading screen then flashes a blue error screen then back to display boot options.  I don't have a recovery disc as the laptop does not have a CD-ROM drive or a floppy drive.  I have the product key, but I don't know where or how repair the operating system.

  Contact the manufacturer of your laptop as there must be a way to restore the computer. There may be a hidden restore partition.

• Bluescreen error: bccode 116; computer turns off on the reboot screen everything seems fine.

  Original title: while using the computer turns off on the reboot screen, everything seems fine. received message the last time. Signature of the problem: any suggestions?

  While using the computer turns off on the reboot screen, everything seems fine. received message the last time.

  Signature of the problem:

  Problem event name: BlueScreen

  The system version: 6.0.6002.2.2.0.768.3

  Locale ID: 1033

  More information about the problem:

  BCCode:                                               116

  BCP1:                                                    863A52A0

  BCP2:                                                    8DC1C152

  BCP3:                                                    C000009A

  BCP4:                                                    00000004

  OS version: 6_0_6002

  Service Pack: 2_0

  Product:                                               768_1

  any suggestions?

  Hello

  Try the procedure described in the following article.

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly?

  http://support.Microsoft.com/kb/958233

  In addition, update the drivers for graphics cards and check if it helps.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

• Defender is turned off, but does not give me access to it 2 turn on power

  original title: windows Defender

  These days have a lot of problems with my laptop.  Problems with starting.  I need to access windows defender to modify startup programs.  It is said that Defender is turned off, but does not give me access to it 2 turn it on.  In addition, different problems with different users and accounts by the office put in place, it looks like all my users are running different versions of windows, so I don't know where to start with all the problems.  Security sounded like a good place 2 start, so I guess I'll start by Defender problems.  (I have recently downloaded the free security essentials, safety signs so all green lights).

  Hello

  You might have developed some questions so I would make these your
  Admin account. These are in addition to checking your startup
  programs.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  I hope this helps.

• After the upgrade from Office 2007 to Ofice 2010 on my Vista, then my computer turns off after being idle for a while.

  After upgrade Office 2007 to Office 2010 on my Vista, then my computer turns off after being idle for a while. When I turn on my computer, I get the splash screen indicating that Windows has finished unexpectedly and I would like to start in safe mode or normally (pluss a couple more choice...).

  Appears not to occur if there is activity going on--as if do me some work or have itunes playing music or I'm just surfing the internet. Curiously, it seems not to happen if I close Internet Explorer and Outlook.

  I shot all automatic updates for Windows Vista (32 bit) and Microsoft Office.

  Concerning

  B Odd Andersen

  Hi B Odd Andersen,

  I want to clarify if your computer seems to be sleeping or it completely closed after being idle for a while.

  Method 1: If the computer is in power saving mode, check if you can wake the computer from this State by moving the mouse or pressing any key on the keyboard.

  Method 2: Change the power to another and check to see if the problem persists
  Change, create, or delete a power plan (scheme)

  Method 3: check the logs in event viewer for more information on auto-off down

  Open event viewer

  What are the information in event logs? (Event Viewer)

  Note: For your safety and security, it is not recommended to disable Windows Update.
  Activate the update or disable automatic

  Thanks and greetings
  Ajay K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.