High power house with the MHC-GT4D Bluetooth Audio System.

Similar Questions

• Computer memory virtual is increased from 6 to 8 GB and now vm fails to power on with the error massage not enough resources to meet the HA failover, attached screenshot

  Computer memory virtual is increased from 6 to 8 GB and now vm fails to power on with the error massage not enough resources to meet the HA failover, attached screenshot

  The message is usually due to the Admission HA and reservations control configuration memory set on one or more virtual machines. With the default configuration HA calculates the sizes of slot based on the memory and CPU. Any reserve on a virtual machine could increase the size of the slot and lead to fewer available seats. What you can do is either to reduce (or eliminate) reservations about the VM (s) or set admission control to a percentage rather than the host failures tolerated.

  André

• With the help of an operating system older Compaq is professional Windows. Internet Explorer connected very slowly. .

  With the help of an operating system older Compaq is professional Windows. Internet Explorer connected very slowly. SO I've reworded in safe mode with network and IE has worked very well. I installed Mozilla Firefox and then restarted in normal mode. Then Internet explorer would not connect. How to diagnose in safe mode. What does safe mode or safe mode with network do to help diagnose? Can someone help me solve this problem? Any help would be appreciated thanks in advance.

  Hi, Raymond J,.

  ·         Did you do changes on the computer before the show?

  ·         You get the error message?

  ·         What type of internet connection do you use?

  ·         What security software do you use?

  Follow these methods.

  Method 1: As the problem does not persist in SafeMode with network, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click restart to restart the computer.

  Method 2: Follow the steps in the article.

  How to troubleshoot possible causes of Internet connection problems in Windows XP

  How to reset the Protocol Internet (TCP/IP)

• What is the printer that HP 7525 works with the windows 8.1 operating system?

  What is the printer HP 7525 Photo Smart works with the windows 8.1 operating system?

  Hi Alex7171,

  Yes it does, you can follow this link to download drivers

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&product=5286643&I

• How to use Sync high speed (HSS) with the HVL-F60M on a NEX-6

  I recently bought the HVL-F60M flasgship flash for my NEX-6. I can't see how to exploit the higher with the NEX-6 synchronization speeds. The built-in pop-up flash is limited to 1/160th shuter speed flash sync. The HVL-F60M claims can I synchronize the maximum of 1/4000e camera which is one of the main reasons I bought this flash. I've scoured the menus but can't find this configuration. Can someone point me in the right direction. Thank you.

  Hi, thanks for the response. I since found that HSS is disabled when the flash HVL-F60M has the bounce flash diffuser installed. There is a small magnet on the hood that tell the camera what it is attached. I guess that the indirect light and power are not suitable for high speed motion gel. I can adjust the shutter speed all the way up to 1/4000 in mode S and M. which concerns

  cmosse wrote:
  

  • Make sure THAT HSS is activated on the flash
  • Set the camera to the mode S and select shutter speed<>

• iOS 9.3 do bluetooth hands-free connection to my Audi stuttering. Using google maps with instructions of the Tower burn on bluetooth still works very well. It's an iPhone 6. Another 6s to 9.2 iOS iPhone works very well with the hands-free bluetooth.

  iOS 9.3 made connection kit hands free bluetooth to my Audi stuttering.

  Both the speaker and the stuttering/pulse microphone so that you cannot speak/hear.

  Using googlemap-app with instructions of the Tower burn via bluetooth still works very well, his is perfect.

  It's an iPhone 6s and the car is an Audi A6 2010 with the Moose Bluetooth adapter business.

  Another 6s to 9.2 iOS iPhone works fine with bluetooth hands-free, just like my phone before the upgrade.

  I tried to disable the twinning, remove all old in the car and the iPhone and pair Bluetooth devices again.

  Anyone alse experinceing this?

  And tip on how to fix it?

  I have the same problem with Audi Q7 2008 and iPhone-6s - iOS - 9.3.

• I have a p6210f (Win 7), that does not illuminate. As recommended, I tried a new power supply with the same results.

  In my post in November, I explained that I had tested the power supply with a multimeter and read the correct voltage. Two people to the Board of Directors always seem to think it was the power supply, so I replaced it with a new one (Corsair CX 430 R) and it still won't turn. I had suspected the power switch because when I bypass the MOBO 20 pin plug 'on', the power led lights up, fans have come on short and I heard the rotation of the disk. I also tried to troubleshoot the switch by jumpering the pins on the motherboard, but still no luck. Someone there ideas more before I replace the card MOTHER and CPU? Thanks in advance.

  Roamstead

  Cloud_strider,

  Thanks for the reply. After swapping the PSU, CPU, taking the RAM pins on jumping on the MOBO for power/LED/reset button, each separately and with the same result, I eventually swapped the MOBO to an ASRock A785GM - THE and who did! He finally put under tension. Thanks again.

  roamstead

• Windows 8 "There is a problem with the driver for bluetooth hands-free audio"

  There is an X symbol by the sound icon, when clicked, it shows "There is a problem with the driver for the audio blue tooth hands-free". Troubleshooting has not been set, said that there is a bluetooth hands-free audio driver problem. In addition, when you look at the audio in Device Manager, error code 19 lights during all the points listed under ' audio, video and game controllers ".

  Hello

  Thanks for posting your question on the Microsoft community.

  We need more information about the issue so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the question and your efforts to resolve.

  This problem may occur because of corrupted audio driver or settings.

  I suggest you run this Microsoft fixit and verify.
  Reference:
  Hardware devices do not work or are not detected in Windows
  https://support.Microsoft.com/en-us/mats/hardware_device_problems

  Automatically, he diagnoses and fixes problems with the hardware. Keyboard and mouse are not detected by the Manager of devices or when they do not work.

  I would also say that you uninstall and reinstall the sound drivers under "Audio, video and game controllers" and check.

  To uninstall the driver, please follow these steps:

  a. press Windows + R keys, type devmgmt.msc in the run window and press ENTER.

  b. Click to enlarge "Audio, video and game controllers", right click on the device, and then click Uninstall.

  c. restart the computer.

  Now, reinstall the drivers from the computer manufacturer's website and check the.
  Reference:
  http://Windows.Microsoft.com/en-us/Windows-8/all-drivers

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• I have a problem with the use of bluetooth.

  I am not able to Bluetooth on my pc in pc settings it shows a blurry icon and is not able to click on it?
  How do I on bluetooth

  Mandeep Hello,

  1. is your Bluetooth device detected on the computer?
  2. What is the brand and model of the Bluetooth device?
  3. have you checked if the Bluetooth device is compatible with Windows 8.1?

  Method 1: Check if your Bluetooth Support Service status is started in the services:

  1. press Windows key + X key together on the keyboard.

  2. Select run.

  3. in command type "services.msc" without the quotes, and then click OK.

  4 search for the Service of Support of Bluetooth and click on it to check the status that appears on the left side of the services window.

  5. If the Service is not started, click right on Bluetooth Support Service.

  6. click on start.

  Method 2: I suggest you follow the link which explains everything below:

  Why isn't Windows find my Bluetooth or other wireless device?
  http://Windows.Microsoft.com/en-us/Windows-8/why-isn ' t-windows-conclusion-device

  Hope this helps, reply with the status of the question for any further assistance.

• High logical reads with the INSERT statement

  Hello
  
  I have an INSERT query that is having a very high reading statspack logical reads. I've seen go Asktom announcement that this is due to the index. Link: [http://asktom.oracle.com/pls/asktom/f?p=100:11:0:P11_QUESTION_ID:6643159615303]
  
  Can you please help to explain exactly what Oracle do and why you should read so the e/s logic. It's the that oracle must read the structure of the index for all (bundle branch block + all blocks of sheet) for each insertion line?
  
  Thanks & appreciate the insight.
  
  Rgds
  Ung

  Only 5 bound for first INSERTION and only 1 for the next INSERTION.

  This is false.

  "db block ' is ALSO to the e/s logic." This is gets them in CURRENT mode. Oracle reads the Index blocks in the current mode to update the index blocks.

  Your last statement is in direct contradiction with the previous paragraph

  As Tom mentioned, oracle must change the index as well when records are inserted in > (or updated or deleted from) the table. This means oracle must first read the index blocks (in > compatibility mode (LIO) as well as in current mode) in addition to the blocks of the turntable when inserting new > records. So this must explain why LIOs are more when inserting in an indexed table from > inserting into a table not indexed.

  What is correct.

  Hemant K Collette
  http://hemantoracledba.blogspot.com

• Problem with the addition of bluetooth for PhoneGap connection

  I have similar issue to the topic found on this forum, I am trying to use the same library of don/BluetoothSerial to connect my phone (Redmi Note 3) with PhoneGap app for mobile robot based on the atmega. I have already programmed robot to move in response to orders received and tested on the terminal application. Now, I need to achieve this with the mentioned plugin.

  I created the project by default, installed the plugin with CLI and modified files:

  Index.html: http://pastebin.com/8FA4DTtW

  Index.js: http://pastebin.com/ivbmMZPa

  config.XML: http://pastebin.com/mFdmr0Tv

  Then I executed cordova platform add android (I don't know if this is necessary in this case) :

  AndroidManifest.xml: http://pastebin.com/iNTXF1hh

  I run the browser application to check the logs from the console, everything seems to be fine fine browser does not support bth:

  Received the event: deviceready

  (index): 68 bluetoothSerial.connect: 98:D3:31:40:06:5 C

  When I try to run it on App Developer PhoneGap, scripts are broken and I am not getting any event neither success nor failure. I would be very grateful if someone teaches me how to call this function correctly.

  Version of Cordoba:

  5.2.2 Android

  browser 4.1.0

  Thanks for your reply, the real problem turned out be the version of phonegap. I followed the steps in this thread and it allowed me to build and install the plugin correctly.

• I HAVE COMPAQ MINI 110 HAVE A PROBLEM WITH THE PASSWORD OF PIOS. SYSTEM HAULT CODE IS; CNU9243TDY

  I HAVE COMPAQ MINI 110 HAVE A PROBLEM WITH THE PASSWORD OF PIOS.

  SYSTEM HAULT CODE IS; CNU9243TDY

  ways to help

  Hello

  Try to enter: e9lo7vfati (3rd character is a lowercase L)

  Kind regards

  DP - K

• Problem with the RTEXE file on PXI system

  I have attached the image of the comic to a very simple code that illustrates a problem with a file RTEXE on PXI system.

  If the VI (LabVIEW 2011) is started on the target of the RT of a LabVIEW project, no problem.

  If the code (with the shared variable linked to a typedef of indicator I32, lvlib being on target and ctl files) is compiled and run in starting my PXI system, it does not (message = "bad state" or something equivalent in french)!

  But when the shared variable is disconnected the typedef, the RTEXE file runs correctly in starting...

  No explanation for this strange behavior?

  A way to execute a RTEXE file on a PXI controller with shared variables typedefs?

  Thanx & BR,

  HL

  I have an answer on the french section of the forum: it's a LabView2011 bug, fixed in LabVIEW2012.

  LabVIEW2011 the only solution is to disconnect the shared variable the typedef

  Kind regards

  HL

• Problem with the certificate on Xbox 360 system Internet Explorer error

  Original title: that is this "problem with certificates?

  I have been using Bing on my Xbox 360 Internet Explorer system for years with little trouble. Today, I cleaned the history since he was a little slow again, but now I am unable to connect to Bing (or really any Microsoft site) through the Xbox 360 Internet Explorer. Whenever I try, I keep coming to a screen message saying that there is a problem with the certificate on the site. I am able to log in and connect to these same sites fine on my computer, but I don't have access to my computer all the time, so it was nice to be able to use Bing on my Xbox 360, but now with this error I can't. What is the cause of this, and what can be done to remedy this.

  It seems that a recent patch for the application of EI on the Xbox 360 has solved this problem now.

• Problem with the playback of an audio .asx file in Windows Media Player.

  Hello

  I'm not able to play an audio .asx file in Windows Media Player on the Windows Vista-based computer.

  I get the following in a pop-up error message:

  Windows Media Player cannot play the file because the specified protocol is not supported. If you typed a URL in the open URL dialog box, try using a different transport protocol (for example, "http:" or "rtsp:").

  Help, please.

  My email address is * address email is removed from the privacy *

  Thank you.

  -HimAlandi

  Hello

   
  1. facing this problem with the .asx format?
  2. you remember to make changes to the system?
  3. where is the file?
   
  Error message: "Windows Media Player cannot play the file because the specified protocol is not supported. If you typed a URL in the open URL dialog box, try using a different transport protocol (for example, "http:" or "rtsp:"). »
  Windows Media Player cannot play the file because the specified protocol is not supported by the player or not supported by the server.
  If you encountered this error by clicking a link on a Web page, the link isn't valid.
  If you encountered this error by typing a URL in the open URL dialog, try opening the file using a different transport protocol (for example, "http:" or "rtsp:").
  The following is a list of protocols supported by the player and the correct URL syntax examples:
  
  (a) MMS://serveur/nom_fichier (for example, a file with a .wma, .wmv, .asf, or .mp3 extension)
  (b) http://server/filename
  (c) rtsp://server/filename
  (d) mms://server/sami.asf? SAMI = http://server/sami/sami_demo.smi (SAMI file)
  If the Player supports the protocol you used in the URL and you can't always read the content, check that the drive is configured to use all of its supported protocols.
   
  To configure the protocol settings
  (a) in the Player Windows Media, on the Tools menu, click Options.
  (b) in the Options dialog box, on the tab of network in the Streaming protocols area, select all the checkboxes (Multicast, UDP, TCP, and HTTP) Protocol, so that a check mark appears in each.
  (c) note that the supported protocols can be used only to distribute digital media files. Windows Media Player cannot be used as a browser.
  If the fixes above don't work, you can rename the folder of information network for the drive so that it can rebuild its information network files after restarting it.
   
  To rename the folder of information networking of player.
  
  (a) close Windows Media Player. (To do this, on the file menu, click on exit).
  (b) to make the changes that you will be able to see the hidden files and folders
  Show hidden files.
  http://Windows.Microsoft.com/en-us/Windows-Vista/Show-hidden-files
  (c) click Start, and then click computer.
  (d) open the disc drive Local (c :)), open to users.
  (d) open your user account.
  (e) open %APPDATA%\microsoft\windows\sendto and open Local.
  (f) open Microsoft and open Windows Media.
  (g) click on the file and rename it.
  (h) if the file is name12.0, edit as file name as old 12.
  (i) restart the computer and check