Highway X8.2.2, Changing default SIP Port for B2B calls is not possible

Much of community support.

I 10.5.1 (SU1) of CUCM and X8.2.2 Expressway.

I have configured without VPN Jabber and B2B based on the Document calls "CVD-CollabEdgeUsingBE6000 - Apr14.pdf.

everything worked fine for months, but after the upgrade of the X8.2.2 Express way B2B calls are no more work.

After troubleshooting, I found the following:

the DSF Guide tells me to change the default Port to 5061 to 5560 B2B calls because 5061 is also used for the integration of Jabber.

When I look at my record of wirekshark I see cucm tries to connect to the port 5560 expressway, but after sending a SYN packet, cucm receives a RST packet.

When I change back to the port of 5560 to 5061, everything works well again for B2B, but of course encrypted calls Jabber connection is not possible more.

for me, it looks like a bug, but I found nothing on the 'Bug search' tool.

I also tried to disable all Protection rules and I also have a firewall rule for Port 5560. I also tried to change the TCP Port to something different, 3999 for example. All this without success.

Just a little look in the guide.

Two caveats. First thing the guide explains unencrypted SIP - TCP connections, if you want to be aware that both sides use TCP or TLS. If you are using TLS certificates must be good as well.

5560 isn't a port on the highway, this is the port for the trunk on CUCM.

What do you see CUCM sending to Highway: 5560 Setup is not ok.

The port of the highway will not be changed.

If you look at page 30, he 5560 port is used for the "incoming Port *" and the bottom of page 31

You can see that it uses the Expressway IP with port 5060.

On the highway, you configure the area to port 5560 (page 34)

And of course the firewall should also be ok.

Please note messages posted under the stars below and set the thread if it's an answer!

Tags: Cisco Support

Similar Questions

  • Need to change the com port number, but users do not have administrator rights

    Our users don't have administrator rights, however, there are a few pieces of software that communicates with the hardware using COM ports.  Since they don't have administrator rights, you may not click on advanced in the communications port to set the port to the necessary com com.

    I found reg hacks online that say will open the advanced screen to allow the com to be changed, but none that I've found work successfully.

    Can someone tell me the correct registry setting that I need to grant permission to in order to open the advanced under properties tro communications button and have the available com port number to change.

    Thanks in advance.

    Hello

    You have the computer connected to a network or domain?

    It is not possible to access advanced screen or advanced without administrator rights. I suggest you to contact the administrator of the system to help about it.

  • Change the listening port for SSH on IDS

    Should what command I use to change the listening port on an IDS 4200 series? I listen on another port, and when I applied the S189/S190 update, it changed SSH port 22.

    Just out of curiosity, too, no one knows what else S189/S190 updates change?

    Thank you

    Jim

    Cisco supports only configurations using the CLI interface. The ssh port cannot be changed through the CLI. Modifying the files in config system via the service account is not a good idea and not supported.

  • Change the Source URI for outbound calls using VCS Expressway X8.2

    Hi all

    I would like a little help on a CPL script, that I'm working on. I lived all the examples of community support and I am always sick.

    We run on VCS X8.2.  What I've read, VCS X8.1 has introduced a few new CPL capabilities, including the node location CPL supports rewriting the regex-based source alias.  I would like to take advantage of this new feature. I'm looking for a tutorial or a direction more advanced examples using this new capability.

    Here's my question:

    I have an internal domain "CompanyA.local" and I have a public domain "Entreprisea.com". «My Cisco video endpoints register control VCS with a SIP URI of "[email protected] / * / .local'.»

    Receive calls from outside help "[email protected] / * / com" and the rules of research, I route calls properly internally.

    When I dial an external company, my endpoint is showing a video SIP URI of "[email protected] / * / .local"

    Of course, this isn't a SIP URI dial-able and should be changed to "[email protected] / * / .com'." "

    I know that this can be achieved using CPL, but I have not used this feature before.
    Any help would be appreciated.

    Please suggest an example script CPL I can review.

    I would use a Regex to cover all of my similar to the following endpoints:

    source-url-to-message-regex = "(.*) ' @CompanyA.local '"
    source-url-to-message-replace = "------[email protected] / * /"

    Thanks in advance for any help.

    oooooo, that answer above gave me the answer I was looking for. It does not work! It seems that the syntax for the xml file has changed from pre x 8 and x 8. Looks like I've been using the incorrect syntax. I was missing the AVA: in the clause to the proxy, which is my version of rule switch not working. Still don't know why the address switch did not work, but I prefer the rule-switch anyway, so no big loss for me.

    I've tested, and it is fully functional on my vm VCS x8.2 running lab



    "xmlns:TAA ="http://www.tandberg.net/cpl-extensions"
    "" xmlns: xsi = "http://www.w3.org/2001/XMLSchema-instance"
    xsi: schemaLocation = "urn: ietf:params:xml:ns:cpl cpl.xsd" >
           
             
               
                 "[email protected] / * / ' >
                   
                 

               

             

           

  • Need to change default domain/user for logon in Windows 7 and Vista guest...

    I need to be able to change the default user domain\username login prompt. Team members where I work must be able to connect to a PC users perform a routine check, repair or warranty matenance etc and then reset the 'last loggon' to the user. This allows HIM to be able to hide our having been in their computer, a very important tool when doing security checks and looking for signs of use inappropriate computer, etc.

    In Windows XP, we could use the hack Reg next to reset the default journal, prompt the user and the domain, we need.

    REGEDIT4

    [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon]
    "DefaultUserName"="name of user.
    'DefaultDomainName '=' domain name '.
    "CachePrimaryDomain"="domain name".

    These settings are in the reg of Win 7, but they don't seem to do anything.

    What should I do so that these rule parameters and take control of the journal prompt?

    Thank you

    Ralph Malph

    PS... In my humble OPINION News groups were better...

    And now in recent years is the answer to my question... Where it should be in the group I had in there.

    I found the following .bat file will allow you to set the user name for the next log in Windows 7. (Copy the next lines of text in a text file and give it a .bat extension, then run it as a local administrator).

    Beginning of the .bat code to change the default name for the next journal newspaper in Win 7 *.

    REM echo off

    appeal reg add "HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Authentication\LogonUI" / v LastLoggedOnSAMUser /t REG_SZ /d "Domain\Username" /f

    appeal reg add "HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Authentication\LogonUI" / v LastLoggedOnUser /t REG_SZ /d "Domain\Username" /f

    pause

    End of code for Win 7, log name *.

    For Windows XP, the following .reg file can do the trick... Do the same as above, but use extension .reg...

    Beginning of. Code REG to change the username by default for the next log in Win XP *.

    REGEDIT4

    [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon]
    "DefaultUserName"="name of user.
    'DefaultDomainName '=' domain name '.
    "CachePrimaryDomain"="domain name".

    End code .reg for Win XP login name *.

    Hope this helps,

    Ralph

  • Change default on 'save for Web '.

    On my old computer "XP" I'm sure that when I saved a chart of the default value is jpeg, but on this computer running Windows7, the default is gif.  Is there a way I can change this?

    Go to the John R. Ellis psedbtools Q & A.  This works in Vista and PSE9 in my case.

    Jürgen

  • change default ignition Panel = contentGroup skin id does not

    Hello

    I have change the value by default "spark.skins.spark.PanelSkin" and then by applying this Panel custom skin to my component of the Panel.  I want to be able to create a left, right, and forced to bottom of 10px to the 'contentGroup"- that's all.

    However, I find this task almost impossible.  I'm trying to change:

    < s:Group id = "contentGroup" width = "100%" height = "100%" minWidth = minHeight '0' = '0' >

    < / s:Group >

    TO:

    < s:Group id = "contentGroup" left = "10" right = "10" top = "10" low = "10" width = "100%" height = "100%" minWidth = "0" "0" = minHeight >

    < / s:Group >

    However, this does NOT work.  You can also change it's 'contentGroup's parent... "the content"... from:

    < s:Group id = "content" >

    TO:

    < s:Group left = "10" right = "10" left = "10" top = "10" low = "10" id = "content" >

    does NOT work or the other.

    Can someone tell me please how do the 'contentGroup' have a padding of 10px autour WITHOUT changing the title bar?  Thanks in advance

    I think that your first attempt does not work because you set a width/height size and forced top/left/right/down (width/height take precedence)

    Your second attempt does not work because the 'content' group is in a VerticalLayout that does not respect the constraints of the up, left, down, right.

    EDIT:

    Actually affecting the left/right/up/down on "content" has no effect because at the top of the skin file the override of updateDisplayList() sets to zero.  If you change the two lines from 0 to 10, it should have an effect, but not the desired.  I suggest this approach:

    Try to encapsulate the contentGroup in another group that has the width/height of 100% and the value of the top/left/right/down on the contentGroup:


               
                   
                   

               

    Post edited by: Shongrunden

  • accidentally changed my file association for utorrent and now not loading the game and programs and browsers

    I accidentally changed something in my computer that shuts down my computer to open all the files, I can't even open the Microsoft Fit it online because when I go to install it, I get a pop up window asking me what program I want to run with, but none of the programs offered in the window will work to open the program file. I remember a couple of days ago I have has download a torrent file and one open pop-up window and asked me what program I wanted to associate this file type, I clicked on the option of utorrent, now none of my games, movies or programs run, when I click on them and try to open them I get the same pop-up box asking what application I want to use to open the program with.
    am beyond frustration with this, I even uninstalled my UTorrent program hoping that would solve the problem, but no luck, the game/files/movies and browsers does not start without changing the file to open with something that is not available in the list of the programs listed.,.

    I would be really grateful for the help in reassociating my files for the games will be automatically start as before.

    Thanks in advance
    Susan Nykolyshyn

    Hello
    What happens, when you try to open any program?
    I suggest you try the following methods.
    Method 1:
    When you run an .exe on a Windows XP, Windows Vista or Windows 7 computer file, the file can start another program
    http://support.Microsoft.com/kb/950505
    Method 2:
    You can restore the system to a system restore point when the computer was working fine.
  • Need to change the connection information for Windows 8 - can not connect to computer because associate login hotmail account has been deleted

    Long story short - the email address associated with my Windows 8, log in to my desktop computer has been deleted and now I can't connect to my computer at all.  Is it possible to access my computer without having to take my computer to a technician to reinstall Windows 8?  Any help is appreciated, thanks!

    Hello

    I understand that you have removed the Hotmail account and Windows does not let you connect as a result of this deletion. Unfortunately, there is no other way to enter to account without using the password (if the account is active).

    You can see the Microsoft Account self-help recovery article and check.

    Recover your account

    If no help, I would recommend that you post your query in Windows Live ID support for assistance.

  • change the com port assigned to the fax and scan

    I used fax and scanning for once.  I had to move my external modem to a different port.

    I don't know how to change the windows fax and scan com port manually.

    the wizard does NOT start, I guess because the fax is installed and worked until I had to change the number of COM port...  I need to change the number of pot with hundreds of research, it seems that no one knows how to change manually the Compote in windows fax and scan, unless they use the wizard.

    my assistant does not start. I guess I'm 'old school' I don't need an Assistant, I need to manually change the fax uses com port.

    :-), it's frustrating because help said only: click "fax" in the lower left corner, and they all assume the installation wizard starts and everything will be fine. :-(

    the wizard does not start. :-(

    I am desperate to get my fax work and need to know how to set the correct port number in a system that is installed and running, such as the wizard never starts.

    for anyone who goes out at the end of questions and ideas, I have a fax application stand alone who is working with the new port setting. It's just not a good app for my needs

    Please?

    Thank you

    John

    Post proposed by the moderator of the appropriate forum category

    Hi John,.

    You can follow the steps below to change the COM port for a modem:

    1. search the Device Manager.

    2 look for the Modem device, right-click on it, and then click Properties.

    • If the change settings button is present, you must click on it to make changes to the appliance. If the user account control dialog box appears, confirm that the displayed action corresponds to what you want, and then click continue.
    • If the change settings button is not present, the modem does not support the ability to change the modem settings. Refer to the documentation provided by the vendor of your modem.

    3. on the Advanced tab, click Advanced port settings.

    • If this option is not displayed, the modem does not support the ability to change the assigned COM port. Refer to the documentation provided by the vendor of your modem.

    If the same persists, we suggest that you post your query in Microsoft TechNet so that their support team will provide you in-depth assistance.

    Kind regards.

  • Configuration of the Simulator. How to change default command line?

    Hello

    BlackBerry Java plug-in
    Version: 1.1.2.201004161203 - 16

    Windows XP

    How can I change default command-line for the Simulator?

    I want to delete/keep-lcd-on = true parameter because he throws:

    Internal error - BlackBerry Smartphone Simulator
    ------------------------------------------------
    (Class fledge::Exception) unhandled C++ exceptions:
    Unknown option LcdCollection:keep - lcd-on screen in the command - line.conf

    Thanks to advice.

    This parameter is no longer supported by the BlackBerry smartphone Simulator.

  • SIP URI B2B calls via CUCM and Highway

    Hi all

    Cannot find out how to configure the SIP URI from SX codecs, recorded calls on CUCM.

    I CUCM and IM & P 10.5.1 a pair of X8.5.2 expressway with two areas of course - for B2B calls, and the external jabber.

    I want to make calls of SX-codecs outside via SIP, by using the URI field, for example, [email protected] / * / or [email protected] / * /. How can I configure that?

    I already have the routing model, which is the SIP Trunk for Exp - C, for H323 calls by ip address. Is it possible to make a routing model to call the SIP URI?

    You can see my deployment in this image.

    Best wishes

    Igor

    Hi Igor

    These guides will help you resolve your issues:

    http://www.Cisco.com/c/dam/en/us/TD/docs/voice_ip_comm/Expressway/config_guide/x8-5/Cisco-Expressway-SIP-trunk-to-unified-cm-deployment-guide-CUCM-8-9-10-and-x8-5.PDF

    https://supportforums.Cisco.com/ru/video/12362936

    BR Oleksandr

  • Motorway E v8.5.1 / / URI Source of change for a call out

    I'm changing the source URI for the calls from our internal network to the internet.  We have an internal area that is not routable on the internet and I would like to change for the routable domain.

    Example:

    Internal domain = int.company.com

    External domain = societe.com

    I tried to use a CPL script on highway E (Version 8.5.1) to achieve, but it does not work for some reason any.  Here's the last CPL I am using:



    "xmlns:TAA ="http://www.tandberg.net/cpl-extensions"
    "" xmlns: xsi = "http://www.w3.org/2001/XMLSchema-instance"
    xsi: schemaLocation = "urn: ietf:params:xml:ns:cpl cpl.xsd" >
          
            
              
                 "[email protected] / * / ' >
                  
                

              

            

          

    Someone has any ideas why this wouldn't work?

    Thanks in advance.

    Brandon

    Take a look at the example in this thread for reference, ask-expert-cisco-telepresence-company, and CPL reference material in the Guide Admin Expressway.

    You must change your origin depending on your internal domain, rather than match any incoming/outgoing call, see below.

    [email protected]/*  */" destination=".*">
    Everything else is fine, I tested it with a codec here using your example domains and the called endpoint has shown the correct source address. You have a cpl in place to change the external domain in-house for incoming calls from outside your organization to be able to find the domain that is used for your registered endpoints? Joint a CPL example is based on one that you posted where it will change the outgoing calls to use the external domain and use the internal domain, incoming calls. In addition, for use later, just say "it doesn't work" provides no information of what's going on. Sometimes you can get lucky and see the issue, but other times that we have more detailed information or see what is happening in order to help better understand where is the problem.
  • change the time zone for email marketing

    We have an ongoing email marketing campaign, but our problem is that the zone for the site is set to GMT + 1. Where can I change to GMT + 10. I can't locate it.

    Thank you!

    Hi Mariano,

    Within the partner (http://www.businesscatalyst.com/Admin/Index.aspx?to=PartnerPortal) Portal, go to the sites my site > [select your site by clicking on the site name link], then the option to change the time zone for your site will be possible by clicking on [edit] next to 'Zone' under the heading 'Détails': http://screencast.com/t/dyCK9zSm

  • Change Windows 7 default serial port settings

    I need help how do I change the way Windows 7 control a default serial port COM1.  I use a serial cable very easy to control the special with external hardware.  The serial cable only use the RTS and DTR, GND pin of the cable and does not require special hardware drivers.  I used the camera on several versions of Windows 95 to XP without any problem at all with serial ports.  With Windows 95 - XP serial COM1 port's RTS and DTR lines defined 'stop' by default.  I just upgraded to a new computer with Windows 7 and now have a problem with the serial port.

    For my problem, I need to have the serial port to be 'stop' default until load control software and specifically opens the serial port to turn on the external device.  Using a serial port data Tester (a lot of green and Red led) I see that as soon as Windows 7 starts, it automatically sets the lines DTR, RTS and TD to serial port as "HOT" (high voltage).  This is not acceptable because it activates the external hardware until the control software is loaded!  Similarly when the control software is closed and the serial port is released in Windows 7, the serial port DB, RTS and TD lines are again defined as "HOT" (high voltage) by Windows.

    Computer: Dell Optiplex 745
    Windows 7 Pro 64 bit with SP1 installed
    Serial port on motherboard: Intel ICH8/ICH8R LPC Interface Controller 2810
    Serial driver: Microsoft 6.1.7600.16385 (is up-to-date)

       Settings for COM1:
       -------------------
       Baud Rate:     9600
       Data Bits:     8
       Parity:        None
       Stop Bits:     1
       Flow Control:  None
    

    I spent hours looking at the Manager of devices/port settings and try to find anything online with no luck.  Is it possible that this is because of the way Windows 7 plug-n-play manages the serial port?  How can I turn it off then the port by default as if it was on XP and earlier versions of Windows is 'off '?

    Thanks, Dave

    I need help how do I change the way Windows 7 control a default serial port COM1.  I use a serial cable very easy to control the special with external hardware.  The serial cable only use the RTS and DTR, GND pin of the cable and does not require special hardware drivers.  I used the camera on several versions of Windows 95 to XP without any problem at all with serial ports.  With Windows 95 - XP serial COM1 port's RTS and DTR lines defined 'stop' by default.  I just upgraded to a new computer with Windows 7 and now have a problem with the serial port.

    For my problem, I need to have the serial port to be 'stop' default until load control software and specifically opens the serial port to turn on the external device.  Using a serial port data Tester (a lot of green and Red led) I see that as soon as Windows 7 starts, it automatically sets the lines DTR, RTS and TD to serial port as "HOT" (high voltage).  This is not acceptable because it activates the external hardware until the control software is loaded!  Similarly when the control software is closed and the serial port is released in Windows 7, the serial port DB, RTS and TD lines are again defined as "HOT" (high voltage) by Windows.

    Computer: Dell Optiplex 745
    Windows 7 Pro 64 bit with SP1 installed
    Serial port on motherboard: Intel ICH8/ICH8R LPC Interface Controller 2810
    Serial driver: Microsoft 6.1.7600.16385 (is up-to-date)

       Settings for COM1:
       -------------------
       Baud Rate:     9600
       Data Bits:     8
       Parity:        None
       Stop Bits:     1
       Flow Control:  None
    

    I spent hours looking at the Manager of devices/port settings and try to find anything online with no luck.  Is it possible that this is because of the way Windows 7 plug-n-play manages the serial port?  How can I turn it off then the port by default as if it was on XP and earlier versions of Windows is 'off '?

    Thanks, Dave

    Dave,

    I can't believe that you have not answered this question.  I had the same problem as you trying to control my radio interface.  I just came by for a Dell Optiplex over the weekend and noticed the same problem.  I was searching the Web for an answer when I found this post.  I am happy to say that I found the solution to my Optiplex and how it works for you.  I went into the BIOS and set the UART protection on.  Makes no sense to me because I'm a software guy, only an amateur on the hardware side.  I left the BIOS and the serial port works as it should like in XP.
    Steve

Maybe you are looking for

  • new to apple and may not know a lot about this computer again

    You just bought a new iMAC. So far, I'm green grass on this subject. My first question is how can I know when the keyboard and mouse are all loaded to the top? Second question, is that they are more accountable?

  • DRIVER_IRQL_NOT_LESS_OR_EQUAL (NDIS.sys) does that mean?

    I get DRIVER_IRQL_NOT_LESS_OR_EQUAL (ndis.sys) and (awsnet.sys) and computer restarts all the time, checked all drivers for updates but still happens, how to solve this? [Moved from comments]

  • Cube 3D Setup does not

    I have vista Home premium os on my PC. I have no problem download this game EA sports Nascar Sim Racing. But when I try to run it, it won't work because the cube 3D Setup does not work.

  • VPN client can get the gateway?

    I have a question for a long time. Cisco vpn client will find a gateway to the remote vpn server address. There are many situations in which we need a gateway assigned to the vpn client. If the customer can freely access all private networks. PIX of

  • Cannot add TableView to VerticalFieldManager

    My problem is that if one create a value for money, I can add fields to the optimization of resources, but if I take a tableview which works perfectly without the optimization of resources and add it to the optimization of the vfm resources I'll alwa