HL-DT-ST DVDRAM GSA - T10N ATA Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

Similar Questions

• mouse works does not, his hang.its showing me the error like this. "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged (code 19).

  I recently installed a graphics card for GTA 4, his work properly.bt yesterday my screen crashed it mean clear.when I started in safe mode then it is appeared correct.afterwords all of a sudden my mouse kick & stopped then I uninstalled graphic card.cause of this my connection net failed.plz help me & give me good solution.i have window xp.

  Hi DineshKaria,
  
  This can occur when more than one service is defined for a device, if there is a failure opening the service subkey, or if the driver name cannot be obtained from the service subkey.
   
  Follow the suggestion in the article given below for code 19 and check if the problem is resolved.
  Explanation of error codes generated by Device Manager in Windows XP Professional
   
  Additional reference on:
  Code 19: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged

• HL-DT-ST DVDRAM GT80N "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  I ran provided patches I've uninstalled and restarted. Attempted to update the drivers. I can not get my DVD/ROM to work I have a Toshiba Satellite S855 S5381

  "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19) »

  HL-DT-ST DVDRAM GT80N

  I have windows 8

  How can I erase my registry and start all over again? What exactly I'm looking for?  I found a post for the same problem on a different model, but I can not located what was discussed.   My computer has been used since the beginning of February.  I need to install programs and others.

  I have fished all day found this and it fixed it!

  http://support.Microsoft.com/mats/hardware_device_problems

  Thank you for your help :)

• DVD/CD Rom error: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19).

  Original title: CD-ROM/DVD-Rom problems

  My CD-ROM/DVD-Rom drive does not work when I check the system, I get the following message "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19). "How to solve this problem?  Thank you in advance.

  Try following the steps under "Windows 7 or Windows Vista" in the MS KB article:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  My DVD RW drive, Optiarc AD7530B has stopped working. I get this error message in Device Manager:

  "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  Verification of the solution does not anywhere - thanks Microsoft!

  Anyone know if there is a resolution to this?  The car was working fine so it must be one of these "Windows Updates" which does its magic.

  Hello

  Check these for the good info on CD/DVD - maybe someone with the same unit can give you all the
  correct the registry settings to try. And the drive could be bad.

  CD/DVD units
  http://www.myce.com/storage/

  Forums - a lot of expert real help
  http://Club.myce.com/
  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Error message: "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged" and dvd burner does not

  Original title: dvd burner does not work can not load the driver

  I get this message "windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged.

  Can someone help me?

  Hi Garry_x,

  1. were you able to use the DVD burner before with no problems?

  2. you remember to make changes to the computer recently?

  This can occur when more than one service is defined for a device, if there is a failure at the opening of the service registry entry, or if the driver name cannot be obtained from the service registry entry.

  You can check out the following link and check for the resolution:

  http://TechNet.Microsoft.com/en-us/library/cc772156 (WS.10) .aspx

  You can also read the following article and check if it helps:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Hope this information is useful.

• Error: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19).

  Original title:

  Windows 7 no sound at all

  Hello

  I would like to ask help for Win 7 problem 'No audio '.

  I have a Win 7 64-bit Professional desktop PC. It has a motherboard Asus P5Q - EM.
  Previously, everything worked very well over a year, but now there is no sound at all. I see a little red x in addition to the speacer icon.

  I got a craphics card problem and it has been replaced, and shortly after, I didn't notice that no audio problem.

  First of all, I tried to fix the external audio card drivers - no help. Then I thought to use the motherboard
  audio only and removed the external audio card. I have cheked Bios that there is audio compatible motherboard.
  Windows Manager device shows Audio Realtek High Definetion. (Once I reinstalled externally
  audio card, but did not get it to work and I deleted again and focused on getting the Audio motherboard
  work.)

  Through the Device Manager, I uninstalled the device Audio from Realtek motherboard and all other audio related devices and start the PC.
  After you start Windows 7 detects audio devices well and tries to install the drivers but still said the driver installation failed.

  I also used the troubleshooter in Windows 7. According to the material and audio, I clicked on the audio playback troubleshooting. The system has tried to install the drivers, but all have failed in similar way as after rebootig.

  When I go to see the Audio the Realtek High Defenetion properties, it says:
  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  I downloaded the latest drivers (some 54 Mb file called: 64bit_Vista_Win7_R267) Realtek www-site and run it, but no help. Same problem - no sound at all.

  If I run application system information and go to the "components" > "Problem Devices", it is said Realtek High Definition Audio, error code: failure using the VxD loader. It is also noted on the VAN Miniport (IKEv2), error code: this device does not work properly because Windows cannot load the drivers required for this device.

  I also unplug the beam of the motherboard front audio jack. I thought it may create a connector related issues, but he did not make a difference.

  If I ask the system to update the driver using Device Manager, it says that the piloted is up-to-date.

  I checked the details Realteck Sound Device in the Device Manager and it says under the number "Problem code" 13.

  Also other devices under device 'Video controls and sound game' managers do not work. I uninstalled all the. After reboot Windows 7 detects all the. Win 7 tries to install the drivers, but always fails and yellow! singing appears next to all devices.

  Under the NIC in Device Manager there is another device with the yellow! sign as well. The WAN Miniport (IKE v2). I don't know if it has something to do with this audio problem? Win 7 detects it as well after uninstalling and tries to install drivers after the start, but is also always fails.

  Now, I'm confused and I don't know if the problem is really in the Windows registry database? What is error code 13 of Realtek Audio device and what is actually the VxD loader problem?

  I'm completely lost on how to proceed with this problem.

  Can someone give advice on how to continue with this question...

  Tomppa

  I plugged the the hardware id in the Microsoft Update Catalog and the device is identified as a C-Media CMI8738/C3DX PCI Audio Device but there only Windows 2000/XP drivers available through Windows Update (you need to install the ActiveX control to view and download the drivers):

  http://catalog.update.Microsoft.com/v7/site/search.aspx?q=PCI%5CVEN_13F6%26DEV_0111%26SUBSYS_011113F6%26REV_10

  Connect the hardware id PCIDatabase provides a link to C-Media (one-third to the bottom - device ID 0 x 0111):

  http://www.PCIDatabase.com/vendor_details.php?id=376

  However there are a of the drivers mentioned in the following link that can run, and I suggest to try:

  http://www.SevenForums.com/sound-audio/9824-c-media-Freezy-my-PC.html

  The driver is the "Striker 7.1 pilot" (striker81742.zip) in the following link:

  http://www.htomega.com/downloads.html

  An in these drivers .inf file has an id of material corresponding to your device.

  I recommend the creation of a System Restore Point before trying new drivers.

• error on my dvd windows can't read the dvd, and the answer is: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  I have an error on my windows dvd cannot read dvd and the answer is: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  can you help me please

  Thank you

  If you are uncomfortable with the use of the registry, try this

• Error Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19) Cannot read CD/DVD

  Original title: Acer laptop DVD drive missing

  Hello

  I have an Acer Aspire 5740 G computer laptop running Windows 7. When I tried to play a movie today, it did not work. The green light on the drive of CD flashed several times then stopped and all was silent. I opened my computer and saw that the CD/DVD drive wasn't listening it. I then opened by Device Manager and the two things under CD-ROM/DVD-ROM readers had a yellow triangle and an exclamation point on them.
  One thing has been called; SVI 2ZGTAB8HQ7G5 SCSI CdRom Device
  The other thing was called; TSST Corp CDDVDW TS-L633C
  I clicked on both and saw the message; "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19) »
  The last time I used the CD player a burn a disc over a month. I used Microsoft Fix It but it says to remove the drive and plug it in somewhere else, and I can't really do this because it's the only drive on the laptop and I'm worried I might break if I go out there with force. Can someone help me? I would really appreciate it.

  Hello

  1. what Microsoft FIXIT did you use exactly?

  2 did you a recent software or changes to the material on the computer?

  I suggest you try the steps mentioned below.

  Method 1: Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:

  I also suggest you run the FIXIT from the link below and.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/

  Method 3:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  You can run the FIXIT or you can try the manual steps and check.

  To do: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  Back up the registry

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  Method 4:

  Re-install the drivers DVD

  Completely uninstall the DVD drivers from Device Manager, and then install the latest drivers for your computer.

  Open the Device Manager.

  Once the drivers are completely uninstalled, download the latest drivers from the manufacturer of the computer.

  http://support.Acer.com/us/en/product/default.aspx?tab=1&modelId=1878

  Hope this helps and keep us posted.

• DVD is not accessible? Device status: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  The DVD (matshita dvd r) no longer under folders on the computer.

  Device status: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  When I try to update the driver it says I already have the best driver.

  http://www.pchell.com/hardware/cd_drive_error_code_19.shtml

  In fact, it worked for me.

  Hello

  19 code means there is a driver conflict such as two devices attempt to use the same resources.

  Having too much CD/DVD programs can cause strange problems, especially if they load of parties
  themselves at the start because they will be competing for resources. This does not mean this problem
  has been caused by those, however, it is a possibility that and how much you
  have installed. Uninstall those that, like iTunes, Nero, and others who might be the cause of
  see if that helps.

  -Use and you need to use it again after trying the methods below.

  What happens if a device is not installed correctly? (Run the hardware and devices Troubleshooter)
  http://Windows.Microsoft.com/en-us/Windows-8/what-device-isn ' t-installed-correctly

  If the player comes with your computer to check with the manufacturer of support system. If it isn't check
  with the support of the creation of DVD.

  =====================================================

  From the desktop - WINDOWS key + D while on the screen start to access the desktop:

  WINDOWS key + X or build the mouse in the lower left corner right click and corner - command prompt (ADMIN)

  Enter it below (or COPY and PASTE):

  Reg.exe add "HKLM\System\CurrentControlSet\Services\atapi\Controller0" / f/v EnumDevice1 /t REG_DWORD /d 0x00000001

  RESET
  (from AtishayMSFT)

  ===================================================

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Starting from the command prompt from the desktop - Windows key + X - (Admin)

  SFC/scannow
  (space between C and /)

  Then run CheckDisk execution - chkdsk /r (the / r includes the parameter f controls)

  Windows key + X - command prompt (Admin)

  Chkdsk /r
  (space between the k and /)

  Or run CheckDisk in Windows 8:

  Improve performance by optimizing your hard drive - see "to repair a drive.
  http://Windows.Microsoft.com/en-us/Windows-8/improve-performance-optimizing-hard-drive

  --------------------------------

  Windows key + X - Control Panel

  Try this - Panel - Device Manager - CD/DVD - double-click the device - driver
  Tab: click on update drivers (this will probably do nothing) - then do a CLICK RIGHT to the road.
  UNINSTALL - REBOOT this will refresh the default driver stack

  ====================================================

  If necessary:

  Try to do a "Refresh your PC without affecting your files" (or modification of your personal data
  settings) or even a restore.

  Windows 8 includes special discount methods (keep files and settings) or a reset
  (new installation remove all).

  How to restore, refresh or reset your PC
  http://Windows.Microsoft.com/en-us/Windows-8/restore-refresh-reset-PC

  How to create a system image to refresh your PC in Windows 8
  http://support.Microsoft.com/kb/2748351

  How to update Windows 8
  http://www.eightforums.com/tutorials/2293-refresh-Windows-8-a.html

  How to reset Windows 8
  http://www.eightforums.com/tutorials/2302-reset-Windows-8-a.html

  =====================================

  Expert help with CD/DVD drive issues available here:

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://Club.myce.com/F61/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" experience :="" bicycle="" -="" mark="" twain="" said="" it="">

• USB 3 doesn't work does not Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  ASUS sabertooth z77 motherboard, bios updated. USB 2 USB 3 does not work. Have uninstalled root hubs that show problems and restarted the computer, do not solve the problem, still getting the "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19) "message under properties. Specific location of the hub of the problem: ASMedia USB 3.0 eXtensible Host Controller - 0096 (Microsoft).

  Please notify. If it is a regedit fix, please help with details. Thank you!

  When I rebuilt my system, I went step by step in reinstalling the software.  I understand that better, my usb problems related to Asus motherboard utilities.  These are not entirely compatible Windows 8 and introduce problematic drivers.  Finished to start my Acronis True Image boot USB and backup of backup image of this morning.  Problem solved.

  Staying away the Asus utilities for now... btw, Asus technical support on my problems was totally useless, even if the code 19 errors point to hardware problems, which are covered by the guarantee.

  If you use the Asus utilities, you may be able to rebuilt without them...

• HL-DT-ST DVDRAM GH24NS07 ATA Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 39)

  See the question above.  Thank you for your help.

  Hello

  Code 39 means that the driver is corrupted or missing.

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  --------------------------------------------------------------

  Also check with your system manufacturer to see if there are any updated drivers for your DVD. Or even if it
  are you can reinstall the 'old'. Many use Windows default drivers however some special aura
  ones. Also check the website of the manufacturer of the car.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19) - Windows 7

  my cd/dvd drive does not work... fix it does not recognize that I have even one?

  Hi Michelle,

  What is the brand and model of the computer?

  A registry problem was detected. This can occur when more than one service is defined for a device, if there is a failure at the opening of the service registry entry, or if the driver name cannot be obtained from the service registry entry.

  We will analyze and identify the cause of the problem.

  Method 1:

  You can run the hardware troubleshooter and check.

  Reference:

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:

  I suggest you perform the steps described in the article:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  You can run the FIXIT or you can try the manual steps and check.

  To do: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  Back up the registry

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  Hope this information helps. Response with status so that we can help you.

• 8 Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  I seem to have a similar problem, except that none of the "fixes" posted doesn't work for me.  I use a PC HP 64 bit of Windows 8

  and my cd/dvd drive and usb cd/dvd drives are not recognized by Windows.  I can 'boot' from the cd/dvd as well as

  I am sure that the bios is ok.  The various "fixes" to the registry have not worked for me.

  Any other ideas?  I really want to avoid a "clean" installation as my HP went from Vista to Windows 7 to Windows 8 and

  There is a whole bunch of things, that I really want to keep.

  Try to remove the GEARAspiWDM entry.

  To remove the GEARAspiWDM entry double-click UpperFilters and, under value data, delete GEARAspiWDM > OK

  Create a system restore point beforehand and restart the computer after.

  However, if you have an application that uses the GEARAspiWDM, like iTunes, just install the latest version of hardware drivers (4.020.5) and that no changes to the registry:

  http://www.GearSoftware.com/support/drivers.php

  Updated speed drivers should also correct the mistake.

• Error message: "Windows cannot start this hardware device because its configuration (in the registry) information are incomplete" and DVD disc is not recognized.

  Original title: My DVD drive is not recognized, it works physicaly works fine, but the pc does not even detect it exists.

  The error that says: "Windows cannot start this hardware device because its configuration (in the registry) information are incomplete."

  I did a backup and restored my system to the factory settings. After doing this still dvd was not recognized. I don't know what to do, my computer is new and Security told me that they will restore the pc and try to fix it, I can't risk my documents of the University are the same that has not worked for me before.
  Could someone help me?
  -The pilot is the last in line.
  -The works of reader dvd but the computer is not reading it, it does not even appear on the section 'computer '.
  -J' tried to use a "fix - it" on Microsoft online, but it doesn't work anymore.
  -My OS is Windows 7.
  -A restore factory settings did not work at all.
  Thank you.
  Claudio Nahmad
  Mexico City

  Hi, Claudio Nahmad,.

  This error can occur if the data in the registry for the device and its driver has been corrupted.

  Since you have already done a factory restore, leave, try to uninstall and reinstall the driver CD\DVD and check if it helps.
  Code 19: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged

  We can also refer to article and check if it helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  Important: The above links contains steps to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information, you can view the article:

  Back up the registry

  You can also try to install Windows updates, including optional updates driver and check if that helps.

  Install Windows updates in Windows 7

  Hope the helps of information.