Host cannot communicate with all other nodes in the cluster virtual SAN allowed

Similar Questions

• Error "host cannot communicate with all other nodes in the cluster of enabeld VSAN.

  Hello community,

  We have a problem (?).

  We have a cluster VSAN enabled with four hosts. Everything seems perfect,

  -the configuration is good,

  -Displays the page state VSAN "network status: (green arrow) Normal."

  -Displays the disk management page "status: healthy" for all of our groups of disks.

  -Same 'esxcli vsan cluster get"on each host returns a 'HEALTHY '.

  But we have a yellow exclamation littly on each host 'host cannot communicate with all other nodes in the cluster of enabeld VSAN.

  Anyone with the same problem? Anyone with an idea or a hint?

  Thank you!

  Update vcenter to the latest version and the error disappears. Problem solved! The 'old' version of vcenter performed since September 2014, strange.

  Thank you very much for your help!

• AnyConnect Clients cannot communicate with each other

  I have a problem that I've been pulling my hair out... my teleworkers connect to our network of Corp. via a connection AnyConnect VPN (version 3.1) to a Cisco ASA5520. I have not split tunneling enabled for this profile, so that all traffic should pass through the tunnel and all guests are in the same subnet L3... as far as their IP VPN address goes. The problem is the teleworker PCs cannot communicate with each other (pings/RDP/etc.). When I look at the newspaper I see traffic from one to another, have denied anything, but they do not communicate. My Network Corp., I can communicate with the two PCs Anyconnect very well. When I go to monitoring. ASDM itineraries I see each host that is connected to the ASA via Anyconnect, and the gateway for each is the default gateway of the SAA.

  Am I missing some setting in the VPN profile that prevents the access between these hosts? I think that something come in the newspaper...

  Have you enabled crossed and also a free NAT between AnyConnect users?

  permit same-security-traffic intra-interface

  network of the AnyConnect_users object

  subnet

  public static AnyConnect_users AnyConnect_users destination NAT (outside, outside) static source AnyConnect_users AnyConnect_users

  If this does not resolve your problem, please post a sanitized complete configuration of your ASA.

• HELP: What router supports VLAN? -I wish both groups cannot communicate with each other.

  Hi all

  I have 5 wireless devices must connect to the router.

  I want to divide it into 2 groups:

  That is to say, 1, device A, B, C, group 2, device D, E.

  I would like two groups cannot communicate with each other.

  I've heard, it can be done by VLAN, is e2500 can adapt to what I need?

  What about EA3500 and EA4500?

  I use G wireless, is what it means that ea4500 is out of choice even if it supports VLAN?

  Thank you all!

  Evil

  Thanks for the clarification for the OP

  FWIW

  is this an alternative to routers that do not support of VLAN, to do what you want

  http://www.SmallNetBuilder.com/lanwan/lanwan-HOWTO/32486-how-to-segment-a-small-LAN-using-tagged-VLA...

• My Wacom pen works with all other functions than the brush / pencil?

  My Wacom pen works with all other functions than the brush / pencil. He painted with the opposite end, the eraser to erase end? Does anyone have a suggestion what to do?

  Annette

  My husbond problem - I had somehow clicked away from the "normal" position Ooops!

• 6.0 U1b - hosts cannot communicate

  Since the upgrade to 6.0 U1b this weekend, I see the following on some of my hosts warning (DR + prod environment), the warning will not disappear until a host is put in maintenance mode / restarted - which cases the other 3 a 4 host cluster hosts display the message. Health/network check all the show as usual, the cluster works normally, so I think this is a warning which is not compensation when a host reboots / fate of maintenance mode?

  People, several clients hitting this problem after upgrading to 6.0U1b, i.e. messages such as the view "host cannot communicate with all the other nodes in the cluster active VSAN.

  Please apply for Service with GSS (Support). Quote the internal reference of bug 1587500.

  Thank you

  Cormac

• ASA - Tunnel all traffic, allow rays to communicate with each other

  Well, I hope someone can help me with this headache! Switching to employ a PIX and VPN 3005 concentrator Office at home in an ASA5510 for firewall and IPSEC tunnels. It is pretty much a

  • VPN on a stick, multiple rays.
  • All traffic sent by tunnel
  • Internet access through main office (using the web filter) of
  • VOIP to VOIP between rays
  • All departments are using the clients VPN 3005 HW or ASA 5505 s

  HEADQUARTERS: 10.0.0.0/24

  Speaks 1: 192.168.11.0 / 24

  Speaks 2: 192.168.12.0 / 24

  Speaks 3: 192.168.13.0 / 24

  -continues to 192.168.31.0 / 24

  Spoke with the current configuration, 1 can communicate with all the resources in the home, office and Internet integrated properly checked by a tracert. However, the rays cannot communicate with each other. This is required for VOIP traffic, when all TALK TALK calls are made (sites).

  Logging information when talk of talks initiated icmp:

  • No group of translation found for icmp src, dst outside: 192.168.31.1 inside: 192.168.11.1 (type 8, code 0)

  If I remove the nat (outside) 1 192.168.0.0 255.255.00 - rays will begin to respond to each other, but then the rays cannot tunnel through the Home Office Internet traffic. My brain is so scrambled after the cramming of VPN configurations for these days, so I hope someone has an idea. I've always used concentrators 3005, so it's a little different! In the search for documentation for this configuration, I was surprised that this isn't a most common topology. It seems that this article would (http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805734ae.shtml), but there is no rays! In any case, I'm sure this has something to do with NAT rules and perhaps who need access for traffic list speaks of talking.

  =============================================

  ASA Version 8.2 (1)
  !
  hostname asa5510

  interface Ethernet0/0
  Speed 100
  full duplex
  nameif outside
  security-level 0
  IP address 97.65.x.x 255.255.255.224

  interface Ethernet0/1
  Speed 100
  full duplex
  nameif inside
  security-level 100
  IP 10.0.0.40 255.255.0.0

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  the DM_INLINE_NETWORK_1 object-group network
  object-network 10.0.0.0 255.255.0.0

  object-network 192.168.0.0 255.255.0.0

  access-list sheep extended ip 10.0.0.0 allow 255.255.0.0 192.168.0.0 255.255.0.0

  Allow Access-list extended wccp servers ip host 10.0.0.83 a

  Redirect traffic extended access-list deny ip any object-group DM_INLINE_NETWORK_1

  Redirect traffic scope permitted any one ip access-list

  Global 1 interface (outside)
  NAT (outside) 1 192.168.0.0 255.255.0.0
  NAT (inside) 0 access-list sheep
  NAT (inside) 1 10.0.0.0 255.255.0.0

  Route outside 0.0.0.0 0.0.0.0 97.65.x.x 1
  Route inside 192.168.0.0 255.255.255.0 10.0.0.1 1
  Route inside 192.168.2.0 255.255.255.0 10.0.0.1 1
  Route inside 192.168.3.0 255.255.255.0 10.0.0.1 1

  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto ipsec df - bit clear-df outdoors

  Crypto-map dynamic dynmap 1 transform-set RIGHT

  map mymap 65535-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 5
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  crypto ISAKMP ipsec-over-tcp port 10000

  management-access inside

  a basic threat threat detection

  no statistical access list - a threat detection
  no statistical threat detection tcp-interception

  WCCP web cache redirect-list Redirect-traffic group-list password xxxxxxx wccp-servers
  WCCP 90 redirect-list traffic Redirect wccp servers group-list password xxxxxxx

  WebVPN

  internal MJHIvpn group strategy

  attributes of Group Policy MJHIvpn
  value of server WINS 10.0.10.1 10.0.10.2
  value of 10.0.10.1 DNS server 10.0.10.2
  allow password-storage
  Split-tunnel-policy tunnelall
  mjhi.local value by default-field
  allow to NEM

  username field-3002 SjfS1Pq2xZGxHicx encrypted password

  attributes of username field-3002
  VPN-access-hour no
  VPN - 250 simultaneous connections
  VPN-idle-timeout no
  VPN-session-timeout no
  Protocol-tunnel-VPN IPSec
  allow password-storage
  type of remote access service

  remote access to field tunnel-group type

  General-field tunnel-group attributes
  Group Policy - by default-MJHIvpn

  IPSec-attributes of tunnel-group field
  pre-shared-key *.

  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  inspect the they
  inspect the icmp
  !
  global service-policy global_policy

  Hello Ala,

  In Act got to be with the Nat configuration.

  So basically you want to tunnel the traffic on the rays to communicate with each other.

  OK, it would be with a nat 0 with the access list with the corresponding traffic outside.

  Also on the crypto ACL for each site configuration, you must add an entry for the traffic of other offices.

  I hope that I have explained myself.

  Have a good

  Julio

  Note all useful posts!

• My Dell all-in-one 962 stopped printing all of a sudden. The error messages are that the computer cannot communicate with the printer.

  My Dell 962 All In One Printer suddenly stopped to print. I get an error message that the computer cannot communicate with the printer. The error message suggests that I unplug and plug back the power plug and the USB cable to the printer and make sure that there are no restrictions of firewall to the printer. I did what was suggested and still no printing. I have resinstaled the printer from the CD software, I got with the computer and also installed the latest driver using the software of the software upgrade wizard.

  and also installed the latest driver by using the Software Update Wizard software.

  That would not have been the best idea... but it is unlikely that the cause of your immediate problem.

  The next thread does not make much sense to me, but it describes a situation similar to what you described and the proposed solution is supposed to have worked.  Try it and see--> http://en.community.dell.com/support-forums/peripherals/f/3528/t/19483019

  I suspect that what really happens is that the driver has become corrupted.  In many cases, simply reinstall the driver is not fix things; you have to clean the old corrupt driver before installing the new.  Thus, it is more likely that the part "Uninstall" the related response is what is helping rather than playing with services... but go ahead and follow these directions, just in case.  In fact, I suggest that you run under first antimalware scanners before following the tips in the above link.

  If I had not found the link above, that's what I would have suggested (whichrequires that you have Windows XP):

  Often, but not always, the symptoms you describe are caused by a corrupt print job stuck in the queue or a damaged printer driver.  However before you clean things up, on general principles, that you can download, install, update and run full scans with each of these two free programs.

  MalwareBytes AntiMalware

  SUPERAntiSpyware

  Use the free version, not the free trials of "pro" versions  Pay attention during installation uncheck any prechecked boxes that would install some additional third-party programs.

  Do not run the scans at the same time.  Each scan will take a while.  Start one and go do a non-it chore.  Once the scan is finished, leave the program to deal with anything it finds.

  Once done, you can keep or uninstall programs, or both.  If you keep SAS, I suggest to change its default setting does NOT automatically when Windows starts.

  Uninstall all software from Dell to control panel > Add / Remove programs

  Download Microsoft Fixit 50126 impression: http://go.microsoft.com/?linkid=9662904

  Close all running applications (anything with an icon on the taskbar).

  Run the Fixit routine.  Note: The routine Fixit has two modes, light and complete.  It will run in full mode when you check the box "Reset the spooler to print on values."  This will remove all printers, so if you have any other printer installed, I recommend running the Fixit in full mode.  If you have other printers and you do not (necessarily) want to reinstall them, run the Fixit in light mode (box unchecked).  This may work anyway.  You must restart the computer after you run in full mode; you need not restart after the Chase mode.

  After the Fixit has executed and you have restarted if necessary, make sure that the printer is disconnected from the computer and run the installation software.  You will be asked to connect the printer to a suitable place.  You can use the CD that came with the computer or download the software here (which is relatively hard to find, the claims of the main page of the 962 product support it cannot find the drivers)--> http://www.dell.com/support/home/us/en/19/Drivers/DriversDetails?driverId=R89490

• Cannot add host ESXi 5.5 to vCenter for a routed network - cannot communicate with the specified host

  I was wondering if anyone has come across this problem before, who could give advice how to fix them:

  Host of pre-production UCS ESXi migration of a Production vCenter on another network (routing in place)

  Can ping both directions successfully - from vCenter Prod to the host of the pre-production

  no firewall between the two.

  902 port is open on the host

  Host connects to the pre-production vCenter on the subnet even fine

  VCenter production can add different hosts on the same network end

  Even with the various guests of ESXi UCS.

  ESXi host was completely disconnected and removed from vCenter inherited before attempting to add. No dvswitch physical or virtual.

  Then try and add, enter the user name and password and get cannot communicate with the specified host.

  Thank you

  The solution to this. Used ESX host 5.5 3B (3248547) update that disables SSLv3. (Ref: VMware ESXi 5.5 updated Notes version 3B) one of the consequences of this is that older versions of vCenter (such as trying to move the host) can not add/connect host.

  Enable SSLv3 to spend (port 443) on the resolved host (virtuallyPeculiar: connection A ESXi 5.5 U3b host to vCenter with a lower Version A.)

  Note: should not enable SSLv3 to Port 902.

  Ref:

  The SSLv3 Protocol on vSphere 5.x configuration (2139396) | VMware KB

  Many thanks to Suhas Savkoor of virtuallyPeculiar for resolution for this on his website display

• Storm Smartphones blackBerry all of a sudden cannot communicate with a MicroSD card? Help

  I've had my Storm for about a week and a half now.  I have Sync successfully several albums of music to my Storm.  The other night, I was listening to music on this device and it froze and suddenly couldn't read the files.  I tried to format the card only to get a message "Media Card Format failed".  In memory, under Media Card menu, it says that "Media Card can not be read. Check that the memory card is formatted.  I can not install the media card in the menu as I chose this option only the phone has no effect.  I have removed the card as well and has managed to format it on my computer and reinstalled with no other success in the phone recognize the memory card.  I also have a 2 GB MicroSD card that I formatted and installed on the phone and I get the same messages with this card as well.  Is anyone here can help me with this situation or is my phone call?

  remove the battery for 15 seconds, then replace them.

• Cannot communicate with DNS sever

  Hello

  IM sharing one House with 3 others, we recently had the internet but I can't connect to it while everyone can. When I connect just says local connection, when I diagnose the connection an error message appears saying "cannot communicate with the DNS server. I've never had this problem before and are still able to use also wireless devices and connect to the internet, it just seems to be this router im having a problem with. Ive tried several suggestions found on the internet and none have succeeded, so I was wondering if someone could help me.

  I'm not sure what information you need to know to help so im just stuck it:

  C:\Users\Kayleigh>ipconfig/all

  Windows IP configuration

  Name of the host...: Kayleigh-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Intel(r) PRO/Wireless 3945ABG Network Con
  connection
  Physical address.... : 00-19-D2-86-0F-71
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::283b:e88b:bf85:ab79% 10 (Preferred)
  IPv4 address: 192.168.0.2 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: November 16, 2009 18:09:40
  Expiry of the lease...: November 17, 2009 18:27:23
  ... Default gateway. : 192.168.0.1.
  DHCP server...: 192.168.0.1.
  DHCPv6 IOOKING...: 251664850
  DHCPv6 DUID customer...: 00-01-00-01-0E-7B-45-98-00-A0-D1-6D-87-63

  DNS servers...: 192.168.0.1.
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Intel(r) PRO/100 VE Network Connection
  Physical address.... : 00-A0-D1-6D-87-63
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {A66451AD - 40 C 4-4DFD-8693-2AB69727F
  E39}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 16:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {5291AF49-A5C9-4154-90AC-597BAF10F
  533}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Card 6TO4
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 18:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {ECA18F57-EF5B-4DA4-8331-B99497389
  06TH}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 19:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {ECA18F57-EF5B-4DA4-8331-B99497389
  06TH}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 21:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {ECA18F57-EF5B-4DA4-8331-B99497389
  06TH}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 22:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {ECA18F57-EF5B-4DA4-8331-B99497389
  06TH}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 24:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Card 6TO4
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 25:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {ECA18F57-EF5B-4DA4-8331-B99497389
  06TH}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Thank you Kayleigh

  Hi, I just contacted my IPS they helped

• cannot communicate with primary DNS (68.105.28.11) Server

  I don't have any wireless internet access. When I hit the button diagnosis: "Cannot communicate with primary DNS (68.105.28.11) server." appears

  My IP config:
  Microsoft Windows [Version 6.0.6002]

  Copyright (c) 2006 Microsoft Corporation.  All rights reserved.

  C:\Users\carmen>ipconfig/all

  Windows IP configuration

  Name of the host...: carmen-PC

  Primary Dns suffix...:

  Type of node...: peer-to-peer

  Active... IP routing: No.

  Active... proxy WINS: No.

  ... DNS suffix search list: dc.dc.cox.net

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. : dc.dc.cox.net

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-1F-E1-79-03-4C

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::34b7:70ad:e7c0:14f6% 11 (Preferred)

  IPv4 address...: 192.168.1.116 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Sunday, July 17, 2011 10:02:20

  End of the lease...: Monday, July 18, 2011 10:02:20

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DHCPv6 IOOKING...: 352329697

  DHCPv6 DUID customer...: 00-01-00-01-0F-E5-04-EE-00-1E-EC-75-99-F2

  DNS servers...: 68.105.28.11

  68.105.29.11

  68.105.28.12

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : dc.dc.cox.net

  Description...: Realtek RTL8139/810 x Family Fast Ethernet

  NIC

  Physical address.... : 00-1E-EC-75-99-F2

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::59a7:b3b:4c00:4663% 10 (Preferred)

  IPv4 address...: 192.168.1.119 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Saturday, July 16, 2011 13:46:25

  End of the lease...: Monday, July 18, 2011 10:03:15

  ... Default gateway. : fe80::34b7:70ad:e7c0:14f6 10%

  192.168.1.1

  DHCP server...: 192.168.1.1.

  DHCPv6 IOOKING...: 251665208

  DHCPv6 DUID customer...: 00-01-00-01-0F-E5-04-EE-00-1E-EC-75-99-F2

  DNS servers...: 68.105.28.11

  68.105.29.11

  68.105.28.12

  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Card 6TO4

  Physical address.... : 00-00-00-00-00-00-00-E0

  Active DHCP...
  . : No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 17:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Card 6TO4
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 13:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. : dc.dc.cox.net
  Description...: isatap.dc.dc.cox.net
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 14:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  Description...: isatap.residents.gmu.edu
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...
  . : Yes
  Card tunnel Local Area Connection * 15:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. NAT - wireless.gmu.edu
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 16:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. NAT - wireless.gmu.edu
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 18:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 20:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Card 6TO4
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  C:\Users\carmen >
  Help, please.  I've been using an Ethernet cable, but it is so EMBARRASSING!

  Hi CarmenZL,

  1. did you last changes made on your computer before the show?

  Follow the following troubleshooting methods:

  Method: 1

  I suggest you to rest TCP/IP and check its operation.

  To reset TCP/IP stack to go to this article and follow the instructions.

  How to reset the Protocol Internet (TCP/IP)

  Method: 2

  Also, follow these steps.

  Step: 1

  a. connect to your router (by typing 192.168.0.1 or 192.168.1.1 in the address bar) and connect. Check your user manual or documentation if you don't know the references of logon.

  b. make sure you are in Setup-> basic configuration category.

  c. scroll down until you see "DHCP Server" - if it is disabled, select 'enable '.

  d. enable DHCP if you want, you can change the number that starts the DHCP IP assigning. (This is optional)

  e. use the DNS servers provided by your ISP. There are many DNS servers out there. It is preferable to use your ISP if possible.

  f. scroll down and click 'Save Settings'.

  Step: 2

  a. click on start and then Control Panel.

  b. go to the networking and sharing Center and then click on change adapter settings.

  c. right-click on connection to the Local network and select Properties.

  d. Select Internet Protocol Version 6, and then click Properties.

  e. Select obtain DNS server automatically an address and press Ok.

  f. Select obtain IP address automatically.

  g. Repeat steps for Internet Protocol version 4 as well.

  Method: 3

  Also perform the following troubleshooting steps.

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  On a Windows Vista client computer, you can get an IP address or options from the DHCP server

• My Lexmark printer stopped working and the error message says "printer cannot communicate with the computer" (from "twisted into the USB pins?).

  When my printer stopped working because of error messages about "printer cannot communicate with the computer" (from "twisted into the USB pins?), I tried to change to 2nd USB port without success. I tried a new cable; that did not help.

  Then I uninstalled and reinstalled my Lexmark printer and changed the error message. Now, the printer does not work because "the USB device is not recognized."

  I tried to update the chips; Use 1 USB port; and using the old cable, all this without success. I checked the connections of the cable to the printer and the PC and turn on the printer and goes off; I'm out of ideas. Any other suggestions?

  Hi ChristineKrause,
   

  Here are some links that might help you:

  Peripheral USB is not recognized when you attach it immediately after that your Windows XP computer comes out of standby or hibernation

  Advanced troubleshooting tips for General USB for Windows XP problems

  Try the steps listed in the items mentioned above and see if that helps you solve the problem.

• Windows cannot communicate with primary dns server

  Hey everybody.  I have a home network, wired PC, 1 wifi 1.  WiFi works fine.  wired network printers work well, other computers (laptops work fine both wired and wireless.)  I have a PC (VISTA), which now gives me the "windows cannot communicate with primary dns server.  This has happened a couple of times, but a reboot fixed things.  Once I had to change primary dns server from automatic to 208.67.222.222 (who got to this site), it worked.  Now, the same error, but nothing works.  I have tried in both directions between the DNS auto numbers listed here, also, have tried the following:

  ipconfig/flushdns
  ipconfig/registerdns
  netsh interface ip reset reset.log
  netsh int ip reset resetlog.txt

  and had windows try to reset the DNS of countless times.  Nothing works.  The upgrade to W7 eventually will correct this problem?  Another question, my wife insists on the use of AOL software (I know, I know), even if all that she uses to is by e-mail.  She says she loves interface.  A chance that caused this problem?

  Hello

  1. have there been recent changes to the system before the show?

  2. the problem occurs only with specific applications?

  Method 1:

  Follow the link and follow the steps proposed by Shekhar S and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/cant-communicate-with-primary-DNS-server/9043f785-2f4e-4CC1-ADF5-6ba5ca413749

  Method 2:

  Follow the link below and follow the steps. Check if it helps.

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  http://support.Microsoft.com/kb/928233

  I also suggest you to run the command in the command prompt and check where the Windows Vista computer is pointing to DNS and DHCP.

  ipconfig/all

  Post back with the results in this thread.

  Let us know if it helps.

• Unable to connect to the wireless network, Windows error cannot communicate with the device or the reaource (primary DNS server)

  Original title: internet connection problem

  Hey,.

  I use a wireless connection at home, it works very well in my android and apple gadget, but it does not work for my laptop. It is said:

  1. Windows cannot communicate with the device or the reaource (primary DNS server)

  2. the connection between the Internet and your access point, router or cable modem is broken

  3 problem with access point or wireless adapter

  I think it's an effects of virus or something?  Because yesterday it works really well. How can I fix? Thank you very much

  Hello Hildegard Lydia,

  You may experience this problem for a number of reasons. Some common problems that can cause these problems are: drivers damaged or incompatible, updates missing, network connection settings, hardware problems or software or TCP/IP can sometimes be damaged or corrupted.

  What is the brand and model of your computer?

  Please follow the steps mentioned below:

  Method 1: a component of the Internet connection on your computer is a package of instructions called TCP/IP. TCP/IP can sometimes become damaged or altered. If you can't connect to the Internet and you have tried all other methods to solve the problem, TCP/IP can be causing it.
  I suggest you try to reset the TCP/IP stack.
  http://support.Microsoft.com/kb/299357

  Method 2:

  I suggest that you refer to the following link:

  Why can't I find a wireless network?

  http://Windows.Microsoft.com/en-CA/Windows/cant-find-wireless-network#1TC=Windows-7

  Method 3:

  See the steps in the following link and check:

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-CA/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Please an update on the status of the issue to help you further.