Similar Questions

• PS B110a - wireless configuration will fail if the network has multiple access points

  Photosmart B110a (CN245B) wireless AIO printer.

  I have several wireless access points using the same SSID to provide coverage over a large area. When you install the printer on the screen TouchSmart wireless installation fails. Print report reveals the following error:

  "More than one access point/router wireless was found which matches your network name (SSID). If this is not intended, your HP printer can connect to the wrong network. »

  In my case this IS planned but there seem to be no available option to answer "OK, just connect to any point of access by using my SSID.  If I turn off all but one the APs configuration complete OK. If I have to do every time I turn on the printer the printer is USELESS for me.

  Did I miss something?

  sijomi

  This should not be a problem.  I have a B110 (and another 10 or so HP wireless printers) on a network of airports with 5 access points and they just connect.

  Here are a few suggestions:

  1. don't use WEP - use WPA or WPA2 with a 13 + character password.

  2. enable the SSID broadcast on all access points

  3. do not use the MAC filtering acddress

  4. make sure "AP isolation" or "isolated wireless" is disabled.

  5. make sure that you are not on a private network, virtual, or connected to your network of comments.

  6. If different strings on access points do not work, try the same channel.

• How can I configure a new TimeCapsule for an existing network without having to activate the internal networks?

  I tried to go in advance and choose "Add TimeCapsule to the existing network", but it keeps defaulting to 'add a new network '.

  without having to activate the internal networks?

  "Add TimeCapsule to the existing network.

  You cannot add a TC in an existing network, if there is.

  You must configure the TC for the network.

  It keeps default back to "add a new network.

  So, it's OK... The TC is part of an existing network or makes a new.

  You must connect to the TC network... either wireless or ethernet.

  However, you can manually configure the TC simply plug ethernet for example.

  See, cable using Time Capsule for Mac for backup only.

  The same can be done for the wireless... but a TC is really the bad device for backups if you don't have a network... It's cheaper, faster and more reliable by using a USB key.

• HP oj4632: How do and '=' on my new HP OJ4632 to satisfy the WEP password?

  My WEP password requires a = sign in the middle.  How can I get on the printer keypad whensetting to the top of the new printer?

  You can connect to your router and change the password and SSID to anything you want.

• Model of card mother T7500 and configuration of the controller RAID LSI 1068e

  Hi, I just bought a T7500 workstation I would get around mid-December. Because of current prices for HARD drive storage, I decided to go with the 500 GB basic disk up to HEALING of Thailand. Thus, I am limited to basic integrated RAID controller. Because I am not familiar with the RAID configuration, etc. I wanted to read more before I dive in. The starting point would definitely find what was right for the Precision T7500 motherboard. Surprise! I can't find information anywhere. Even Dell people (3 different sales and support representatives) have not managed to tell me it's the Intel 5520 chipset (it looks that they believe that it is the motherboard model...). Well, I'm stuck. I would appreciate if someone could provide me with the model of motherboard and Special Edition, all information on the capabilities of the controller integrated RAID (LSI 1068e) would help me determine what drives should I plan to buy. In addition, one thing that is not clear to me what I inferred from the configuration on the website Wizard is the issue around disks > 2 TB. Of after I read it, I was not able to determine whether the problem was related to the simple readers > 2 TB or if it was related to the management of a storage space > 2 TB (which could be composed of several readers less than 2 TB). What I have in mind (remember that I do not have the machine right now) is to 4 X 1 TB drives in a RAID 0 + 1 (which I'm not sure that the integrated controller supports) configuration that will result in the storage of 2 GB mirrored. The operating system is Win 7 64 bit. Thanks in advance for any info that will help me to prepare my setup (buy hard drives, if I can find cheap ones) and find information on the configuration of the RAID. MrBricole

  I'm sure the T7500 uses an Intel Server Board (since this chipset is located on the Intel site under its motherboards, Dell is essentially correct, even if they didn't know why), but it doesn't matter in the context of your question, because the '' integrated '' RAID controller is not actually on the Board.  It's a card (called "integrated" only because it has a slot on this machine).  Because the functionality of the RAID controller is not on the Board of Directors, Board info will not help you.  Everything you need to know about your Council and the entire system, you can get the T7500 manual.  SAS 6/iR (LSI 1068e) RAID controller information can be found here:

  NOTE from the ADMIN: Broken link has been removed from this post by Dell >

  The SAS 6/iR will not support more than 2 TB of drives, or it will support more than 2 TB of virtual disks.

  It will also only supports RAID 0 OR RAID 1 OR both, but not together (not levels no RAID nested as RAID 10 or 0 + 1).

  So with four 1 TB drives, you can easily do two RAID 1 (called integrated mirror in the controller BIOS CTRL-C)... or you can do two 2-drive RAID 0 (Stripe called integrated in the controller BIOS CTRL-C)... or you can run mode non-RAID, with four individual discs in the operating system.  With this controller, those are your only options with four 1 TB drives.

  If you want / need more features RAID (nested RAID, 2 TB of the VFD above, on board levels, cache, etc.), you must upgrade to the PERC 6 / i.

  Do not buy office records class... Make sure you get enterprise-class drives.  If you decide at some point to go with PERC, not only enterprise class disks will be fundamentally necessary, but certified records would be strongly recommended for stability and performance.

• How can I configure a game controller for its use prevents the screensaver from starting

  I use a game controller on Windows 7 Pro 64 with Windows 7 (driver HID-compliant game controller). Windows does not seem to recognize this game controller entry, then the screen saver turns on permanently. I tried to turn on "allow this device to wake the computer" in Device Manager. But still no luck. Unfortunately, I'm not allowed to disable the screen saver. Any idea?

  Hi Thomas,

  Thank you for your reply and very clear description.

  Check with the manufacturer of the device if you have the latest updates, if there is, install them.

  If the problem persists, please turn off the screen saver.

  We look forward to your response to help you better.

• How can I configure my new asus laptop with windows 7 to my yahoo email?

  I tried to go in the Panel control and then users then email 62 bits. He then asked which server and what I want to use. then it asks user name and password. then I put the incoming and outgoing mail servers and I've tried a few things but nothing works. I really need my computer to be able to send messages without having to always go into my mail. Thank you!

  Hmmm, my Windows 7 Home Premium 64 bit has no email in Control Panel applet - I don't think other versions of Windows 7 do it either.  Try this.  Set up your browser (Internet Explorer) and go to www.yahoo.com .  Look for the sign in / / Sign up buttons and click on Sign up.  Follow the on-screen instructions to create your account.

  Good luck.

• Max AIR-LAP1142N-E-K9 Access Point devices

  Hello

  How many Wifi devices simultaneously press a Point of access AIR-LAP1142N-E-K9?

  Thank you

  Hello

  I hope that you are looking for the maximum clients that supports the TOWER... Here flax kwhich gives you the exact information you're looking for...

  http://www.Cisco.com/en/us/docs/wireless/controller/7.0/Configuration/Guide/c70ccfg.html#wp1085099

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• How connect N600 router wndr3400v3 to another hotspot or wifi ssid access point

  I want to connect to my router to an another ot hotspot or access point ssid to increase network range

  I tried but not found any option

  Help, please

  Ok thank you

• How to create and configure separate user accounts in Windows XP?

  I had my computer cleaned because of viruses, how create and configure user accounts separate?

  See if the article on the link below answers your question.

  http://support.Microsoft.com/kb/279783

• How can I configure mobile android password manager copy all of my passwords from firefox to my office?

  How can I configure my new mobile password manager for my android phone copy all of my passwords from firefox to my office?
  Right now, I noticed there is only about 8 passwords listed.
  But my office saved password manager has about 50 listed.
  This makes me think that the android app is to choose only to remember what I saved directly with my android. I want to capture all my saved passwords from my desktop also.
  I tried recheck my firefox sync options, but only confirmed that I don't have this game automatically synchronize all my data (including passwords.)

  I found that I have to press the 'Menu' (three horizontal lines in a square) in the mobile view and connect until I'm able to meet Firefox on Android.

  Now that you're on your desktop: try passwords uncheck in synchronization preferences, wait a few seconds, then check again. Then on your phone, the settings of the open Android app, accounts & sync, choose your Firefox Sync account, then Menu > sync now.

• Install ONLY Vision Demo Database and NOT the new installation?

  During the process of installing Oracle Applications R12 on Oracle Enterprise Linux.
  for the database layer, the installer provides an OPTION that allows you to
  ONLY install the (demonstration of Vision database) and NOT the (new installation)?
  
  If so, can you point me to some documentation on how this is achieved and that a
  estimate on how much disk space it would require?
  
  Thank you!

  Hello

  According to the manual 'quick install', page 2-9, it says:
  DIRECT QUOTE - "you can install a new database or a database of demonstration of Vision."
  From this quote, I guess that we can install the demo database, without having to install a database of fresh PROD.
  Don't you think that my assumption is correct?

  Your assumption is correct, but you should consider that quick install will also install the application part also in addition to the database.

  You can either install a fresh database (including the part of the application), but this database is clean (no data), and usually it is used for production after you make the necessary functional configuration OR a vision of the demo database (including the part of the application), and this instance is ready for use as functional configuration is already out in the database (used for demonstration purposes).

  If you are doing a new installation--> you'll need about 90 GB (55 for the database that is clean and 35 GB of application).
  If you do a vision--> you install will need approximately 260 GB (225 for the database which includes configuration data and 35 GB of application).

  Kind regards
  Hussein

• Correct configuration of the Cisco Access Point 1242AG

  Hi all

  Here's the situation:

  Recently, we decided to create a small network of WLAN in our company. We choose the Cisco AIR-AP1242AG-E-K9 with 2x2.4GHz 2.2dbi rotating dipole antenna.

  For better management, a new VLAN routable (ID:20) added to our router IP 192.168.55.1 and SNET 255.255.255.0

  Then, I made the following configurations in the autonomous AP through WEB Console:

  • Static IP:192.20.10.35, SNET:255.255.254.0, GWY:192.20.10.200
  • Vlan1 (native) and VLAN20 (Radio0 - 802.11 g) added in Services.
  • I put the encryption against zero for VLAN1 Mode and cipher AES-CCMP for VLAN20
  • In Server Manager, I've defined a new 192.20.10.35 RADIUS server (AP-IP) and a secret shared and left the default ports for authentication and accounting (1645 and 1646). Also, in the default server priorities section I put focused 1 time for authentication EAP and the IP (Radius Server) 192.20.10.35 Access Point MAC.
  • During the General local RADIUS server configuration, I add as a server for access to the network current (AAA client) the same IP address and the shared secret as the ones I use during the configuration of the RADIUS server above. In authentication protocols enable I left checked only the JUMP and the Mac. In addition, in the users individual section 2 new users created with passwords.
  • In the SSID Manager a new hidden SSID created for interface Radio0 - 802.11 g, associated with VLAN20 and in the Client authentication settings section, I left as accepted authentication open with MAC and EAP authentication method. Also, I left the option to use by default for EAP and MAC authentication servers in Server priorities Section and finally I choose mandatory for key management in the section Client authenticated and active the option enable WPA key management.

  I can ping VLAN20 IPs from any PC which is a member of the VLAN native both AP

  As wireless clients, I use 2 Motorola MC5574 with Windows Mobile 6.1 professional. Both of them have a WLAN Jedi adapter that is configured with the following:

  IPs:192.168.55.10 and 192.168.55.11

  SNET:255.255.255.0

  GWY:192.168.55.1

  In addition, a unique profile has been created on all of them to use for the authentication of the association AP. Each profile has been configured for WPA2-Enterprise with AES and LEAP and identification information predefined user (those defined in the PA for individual users)

  The problem:

  Association of clients with AP is always successful but, authentication fails, and I can't ping the AP IP, IP VLAN20, nor the other customers.

  What I'm missing here? I'm sure it's quite simple somenthing but although I tried several different configurations (even WPA - PSK, WPA2-PSK with TKIP) I always find myself without an appropriate solution to unable to ping.

  Thanks in advance for any help

  Hello

  Can you please paste the show run out of AP?

  Kind regards

  Madhuri

• Problem with SG-200 and access point on VLAN

  I'm having some problems with the configuration of VLANS on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is able to access the internet when it is plugged into a port that is on the default VLAN (1 PVID). If I plug it into one of the other VLAN then all clients connected to WiFi to lose access to the internet and can not access on the local VIRTUAL network devices. I've used this configuration with a Cisco WAP4410N of first generation.

  I'm not sure if it's something wrong with the way I configured the switch or a problem with the access point.

  The setup I have is:

  Modem/router ADSL (7800N billion)

  |

  -------------------Port 1--------------------

  |                                               |

  |               SG-200 08 |

  |                                               |

  ---3---port 8 - port

  |                    |

  Access point |

  (TP-Link WA801N).

  |

  SF - 100 D

  The port configurations are

  Port Mode PVID membership

  1 general 1 1U, 7U, 666U

  2 general 1 1U, 7U, 666U

  3 general 7 1U, 7U

  4 General 7 1U, 7U

  5 General 7 1U, 7U

  6 General 7 1U, 7U

  7 general 1U 666, 666U

  8 General 1U 666, 666U

  Iain,

  You have virtual local networks put in place on your router? The subnets that you use on each vlan? The router will give DHCP for each vlan?

  The SG200 isn't a fully managed layer 3 switch, it's just a "smart switch" so you can not actually be able to do simply only switch. A sg300 mode layer 3 would be able to do this because it is a fully managed switch.

  If the router is configured with the VLAN, vlan 1 unidentified, the rest the tag, the router-> SG200 port is trunking and the others as access ports on their vlan respective. Once the router is configured, this video contributor forum albums and Cisco employee David Hornstein is very useful to correctly configure the switch.

  Best,

  David

  Please evaluate the useful messages.

• WRT600N advanced routing problems / use as Access Point and switch

  Firmware 1.01.36 build 4 The WRT600N is connected to an existing LAN and is really only used as a Wireless N access point. There is nothing plugged into the WAN port; only the LAN port. I have NAT disabled. All traffic from a client connected to the WRT600N wireless going very well for the gateway and the Internet router. The customer experience is very good. However, there are a few minor issues as follows.

  1] Setup > Advanced Routing tab has only the following options; to do this, * not * have a picker 'Mode '. NAT, static routing and dynamic routing (RIP).    IS this NORMAL, OR should HAVE a MODE (e.g. switch) AS REFERRED to IN THE HELP FILES?

  [2] even if a connection wireless or wired to the WRT600N works very well, the WRT600N himself is unable to connect to the internet. It cannot connect to NTP to set the time and I can't ping past the gateway router using the ping of the WRT600N diagnostic utility. I ping the gateway 192.168.1.4 port inside, but I can't use the diagnostic the WRT600N ping ping utility something beyond this gateway port. The routing of the WRT600N table is below. THE GATEWAY SHOULD NOT BE 192/168.1.4? HOWEVER THE WRT600N DON'T ME LETS NOT CHANGE IT.

  Destination LAN IP Subnet Mask gateway interface

  192.168.1.0 255.255.255.0 192.168.1.71 LAN & Wireless

  127.0.0.0 255.0.0.0 * LAN & Wireless

  Topic 1. Linksys, used to have a mode option to switch between the modes 'Bridge' and 'router '. The latest routers call it now better NAT power. Gateway mode means THAT NAT is enabled. Router mode means THAT NAT is disabled. The help files are probably a little bit over. But the option is still the same.

  Re 2. It's normal if you use it as only access point (i.e. do not use the WAN port). The router always takes into account that the internet connection via the WAN port, i.e. it will always use the default gateway on the WAN port. If nothing is connected to the WAN port on the router itself has no default gateway and therefore has no access to the internet. Generally, you are not able to establish the default route in either advanced routing page. It is a known limit of these routers if you do not use as a router.