How can I stop my computer freezes during disk defragment?

Similar Questions

• How can I stop my computer freezes up?

  Sometimes my computer freezes on me, turn it on on any site of spasific, it comes will freeze

  Hello

  • What were the changes made before the issue started?
  • You receive an error message?
  • What version of Windows operating system do you use?
  • This occurs on Internet Explorer?
  • Is - what the computer crashes only when internet access?
  You can check this link:
  Slow PC? Optimize your computer for peak performance
  http://www.Microsoft.com/athome/Setup/optimize.aspx

• How can I stop my computer restart during the installation of Windows updates?

  My laptop Dell Inspiron 1501 problems of marketing, past the login screen. However once I managed to get it on it works fine.
  I get messages saying my computer needs to reboot to install updates - but I'm afraid that I won't be able to restart once it has been automatically disabled.
  These updates sometimes, in the middle of the night when I am not able to postpone updates - how can I activate the restart automatic offf?

  In addition to Robear comments-

  HOW to: Configure and use automatic updates in Windows XP
  http://support.Microsoft.com/kb/306525

  Using Windows Update in Vista
  http://www.Microsoft.com/Windows/downloads/windowsupdate/learn/windowsvista.mspx

  Change how Windows installs or notifies you of updates:
  http://Windows.Microsoft.com/en-us/Windows7/change-how-Windows-installs-or-notifies-you-about-updates 
  http://Windows.Microsoft.com/en-us/Windows7/turn-automatic-updating-on-or-off

  If you want more control, set the parameters of AU to your needs, for example, might be for you not to tell that. TaurArian [MVP] 2005-2010 - Update Services

• How can I stop my computer to turn on automatically at midnight?

  How can I stop my computer to turn on automatically at midnight?

  In addition to the suggestion of Elizabeth23, you can ""disable the wake we LAN "setting in the bios or go to Device Manager and click on the sign '+' to develop " network adapters, right-click on your NETWORK map , and then select Properties. ' " Click the Advanced tab , scroll to ' wake we lan after his stop " and if it is selected, click on the small arrow and set it to disabled. Click the power management tab , and uncheck the box 'allow this device to wake the computer from stanby'

  Good luck.

• How can I stop my computer to go to the screen saver when I for example runs a scan of the computer, sometimes my scan takes a long time to finish?

  My problem is? How can I stop my computer to go to the screen saver when I for example runs a scan of the computer, sometimes my scan takes a long time to finish? Example I have Microsoft Security Essentials set allow to run daily on 1200 AM and until he finishes my computer goes to screen saver Mode. and when I click on my mouse, I must sign completely new in my computer > how to stop this from happening, I want to keep my Security Scan open until there finishes?

  All the solutions for this?

  Original title: Windows Vista systems

  Hello

  This can help you:

  "Enable or disable the screen saver.

  http://Windows.Microsoft.com/en-us/Windows/turn-screen-saver-on-off#1TC=Windows-Vista

  And this is how do to change the time to wait before the screensaver comes on (article 8) and how to disable the password to logon to him (art. 9):

  http://www.Vistax64.com/tutorials/85539-screen-saver.html

  "How to disable or enable Protection by password on Wake Up in Vista"

  http://www.Vistax64.com/tutorials/102686-password-protection-wakeup.html

  See you soon.

• How can I stop my computer to send questionable e-mails to my contacts, I have already installed microsoft security, scan shows no visible threat.

  How can I stop my computer to send questionable e-mails to my contacts, I installed microsoft security, the analyses show no visible threat I changed my password and my contacts are still getting e-mails from me with links attatched to various dodgy sites... I don't know what else to do

  Any help would be great

  Hello

  (1) what email program are you using?

  (2) who is your provider of mail service?

  If you are using Hotmail or Live ID with Windows Live Mail then I suggest you to ask your question in the Windows Live Mail community.

  http://www.windowslivehelp.com/product.aspx?ProductID=15

• How can I stop my computer redirect me to sites that I don't want togo to?

  How can I stop my computer redirect me to sites that I don't want togo to?

  Hello

  Check these:

  IE8 redirect problems - possible Causes and fix the redirect problem
  http://www.brighthub.com/computing/Windows-platform/articles/60039.aspx

  http://EzineArticles.com/?Google-redirect-virus-fix---how-to-get-rid-of-Google-virus&ID=2450094

  http://ask.MetaFilter.com/100853/Oh-that-nasty-Google-redirecting-virus

  http://www.GeeksToGo.com/forum/how-to-fix-Google-redirects-t267407.html

  ------------------------------------------------

  IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

  IE - Tools - Internet Options - Security tab - click on reset all default areas - apply / OK

  Close and restart IE

  IE - tools - manage Addons (for sure disable SSV2 if it is there, it is no longer necessary but Java always install
  "(and it causes problems - you never update Java to go back in and turn it off again)." Search for other possible problems.

  Windows Defender - tools - software explore - look for problems with programs that do not look right. Permit
  are usually OK and "unauthorized" are not always bad. If in doubt about a program to ask about it here.

  Could be that a BHO - BHOremover - free - standalone program, needs no installation, download and run - not all
  are bad, but some can cause your question (toolbars are BHO).
  http://securityxploded.com/bhoremover.php

  Startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Also get Malwarebytes - free - use as scanner only.

  http://www.Malwarebytes.org/

  =========================================
  =========================================

  If necessary and you suspect malware:

  Search for malware and when you are sure that the system is clean and perform the cleanup.

  Make a control examination, as often this kind of malware is accompanied by a much harder to detect and remove the
  payload. Best to go to the sea now rather than pay the price later.

  It can be made repeatedly in Mode safe - F8 tap that you start, however you must also run them
  the Windows when you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone. (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with other security programs. It comes
  a scan only, VERY EFFICIENT, if it finds something to come back here or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software (viruses, Trojans,
  Rootkits, etc.) that has infected your computer despite all the security measures that you have taken (such as
  the anti-virus software, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  New Vista and Windows 7 version
  http://OneCare.live.com/site/en-us/Center/whatsnew.htm

  Original version
  http://OneCare.live.com/site/en-us/default.htm

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also do to the General corruption of cleaning and repair/replace damaged/missing system files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  Hope these helps.

• How can I stop my computer automatically sleep?

  Original title: our computer screen goes to sleep and I need help, fixed the problem

  HOW CAN I STOP MY COMPUTER TO GO TO SLEEP.

  HOW CAN I STOP MY COMPUTER TO GO TO SLEEP.

  First a small label Internet... Please not compose entirely in capital letters. It is considered yelling, screaming, rude.

  To your question. Is it when you left your computer idle ?

  If you don't want to go to sleep when it is inactive, try this method...
  Start button > Search box, type power options >press > on your window Power Options, on the left side, click change when the computer sleeps > there are choices in this new window. Click on thepointer under Plugin and on battery, selectNEVER, if that's what you really want.
  Check out all other options in the Power Options window title. You can set up a power plan for your computer, if you have not already done so.

  t-4-2

• How can I stop my computer with a blue screen coming up and crashing

  Hello

  my computer keeps crahing with a blue screan befor, I ran anti spy wear and its projection up to nothing. When it reboots it says. from what I can tell, it's the same thing all the time.

  help please

  Signature of the problem:

  Problem event name: BlueScreen

  The system version: 6.0.6001.2.1.0.768.3

  Locale ID: 3081

  More information about the problem:

  BCCode: 50

  BCP1: 9131EB99

  BCP2: 00000001

  BCP3: 886F7C45

  BCP4: 00000000

  OS version: 6_0_6001

  Service Pack: 1_0

  Product: 768_1

  Files helping to describe the problem:

  C:\Windows\Minidump\Mini080812-03.dmp

  C:\Users\ricky g\AppData\Local\Temp\WER-440422-0.sysdata.xml

  C:\Users\ricky g\AppData\Local\Temp\WER204C.tmp.version.txt

  Read our privacy statement:

  http://go.Microsoft.com/fwlink/?LinkId=50163&clcid=0x0409

  Hello

  Pick up the pieces after a computer breakdown - see what to do if Windows won't start correctly
  http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crash

  To BlueScreen troubleshooting methods using BlueScreenView and MyEventViewer
  See my answers, if this thread - top 3 responses (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  We can analyze the minidumps if you make them available at the SkyDrive or other
  file sharing sites (such as MediaFire). If you have problems downloading the minidumps
  Copy it to the desktop or Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  -------------------------------------------------------------------------------------------------------------

  BCCode: 50 0 x 00000050

  References to Vista also apply to Windows 7.

  Have you recently added any hardware? Have you updated any drivers just before these
  has started? (Check control panel - updates of Windows to see if all drivers have been updated
  all the time this started) guilty likely hand are video driver, other drivers,.
  memory and antivirus/antispyware/security products could be at fault, but also in car
  questions.

  Use the troubleshooter below and refer to the following message for pilots and memory
  When you get these sections and then back to the resolution of the problems according to the needs.

  BCCode: 50 0 x 00000050

  Cause

  The BCCode 50 usually occurs after the installation of the defective material or in case
  failure of the hardware installed (usually associated with a faulty RAM, either main memory,
  Cache L2 RAM or video RAM memory).

  Another common cause is a defective system service installation.

  Antivirus software can also trigger this error, as can a corrupted NTFS volume.

  Solve the problem

  Solve a defective hardware problem: If the material has been added to the system recently,
  Remove to see if the error recurs. If existing hardware has failed, remove or replace
  the defective component. You must run the diagnostics of material provided by the manufacturer of the system.
  For more information about these procedures, see the manual of your computer.

  Fix a defective system service: Disable the service and confirm that this
  resolves the error. If so, contact the manufacturer of the service on a possible system
  Update. If the error occurs during the system startup, restart your computer, and press F8 to
  character mode menu that displays the choice of operating system. As a result
  Windows Advanced Options, select last good known Configuration option menu.
  This option is most effective when a pilot or a service is added at a time.

  Solve a problem of antivirus software: Disable the program and confirm that this fixes
  the error. If this is the case, contact the manufacturer of the program about a possible update.

  Fix a corrupted NTFS volume:  Run Chkdsk /f /r to detect and repair disk
  errors. You must reboot the system before the start of the analysis of disk on a system partition. If
  the hard drive is SCSI, check for problems between the SCSI controller and the disk.

  Finally, check the system log in Event Viewer for additional error messages that might help
  identify the device or driver that generated the error. Disable the cache in memory of the BIOS
  could also resolve it.
  
  BCCode: 50 0 x 00000050<-- read="" this="">
  * 1095.html? order = votes http://www.faultwire.com/solutions-fatal_error/page-fault-in-NONPAGED-Area-0x00000050-

  -------------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard event viewer
  Windows. TIP - Options - Advanced filter allows you to see a time rather
  of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue
  Screen info that would help. Such as ITC and 4 others entered at the bottom left.
  And other information such as codes STOP error and info such as IRQL_NOT_LESS_OR_EQUAL
  or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during ' blue screen of the.
  death ' crashes and displays information about all accidents of a table.
  Free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by drivers of old or damaged, in particular the video drivers
  However, there are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Does not work
  tell all possible driver issues).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• How can I stop my computer to reset the settings of my screen when I start or when I go on messenger and sign in?

  Whenever I turned off my computer and restart that my display settings are given to such magnification, I can't even change because only a small part of the Panel fits the screen. Please help, I am ready to throw this thing.

  Looks like your PC is infected.

  If you use Microsoft Security Essentials, start here - https://support.microsoftsecurityessentials.com/ and select the link that says - I think my computer is infected. Options vary by region, but phone support leads you to the Microsoft answer service (http://www.answerdesk.com/) in the USA at this time. After an initial free consultation, will be charged a fee for assistance, based on the details of the case.

  If this is not the case, go to your provider AV.

  You can also try this web site - http://www.bleepingcomputer.com - contains details for most common infections, often immediately after that they started to appear in the wild, and instructions are provided for how to remove infections using their malware removal guides. They also have forums where you can seek assistance from people who specialize in the removal of malware.

  Here are other free programs that can help:

  Free Malwarebytes - http://www.malwarebytes.org/products/malwarebytes_free

  SUPERAntiSpyware Free - http://www.superantispyware.com/downloadfile.html?productid=superantispywarefree

  TDSSKiller (free) - http://support.kaspersky.com/faq/?qid=208283363

  HitmanPro (free for 30 days) - http://www.surfright.nl/en/hitmanpro

• How can I stop my computer to open windows in safe mode?

  I just intalled norton security as I had no security for a while, since this window opens in safe mode but it seems oninstallation of security scanning all the risks have been removed how to get back to normal windows mode

  Hello

  1. Close all running programs and open the windows if you are back on the desktop.
  2. Click on the Start () button.
  3. In the search box of the Start Menu, type in msconfig
  4. Then press enter on your keyboard.
  5. The System Configuration utility opens
  6. Make sure that Start Selection is set for Normal start.
  7. Click the Startup tab.
  8. Make sure you start is not checked
  9. Press the apply button and then press the OK button.
  10. Click the restart button to restart your computer.

  See you soon.

• How can I restart without computer freezing after login?

  so I tried to burn a cd using the zune software, and the computer froze on me, after I restarted, I connected it immediately frozen on me and the screen looked like a TV that has been tuned to a channel that does not exist, essentially static. What did wrong and how the hell to fix? Ive tried to launch the command prompt and I get an error message whenever I try to use the system restore, it says that I need to specify which program I want to restore and give the example of restrui.exe/OFFLINE:C:\Windows. what the devil do?

  To start system restore using the command prompt, follow these steps:

  http://support.Microsoft.com/kb/304449

  Zune overheat when you tried to burn a cd?  Your computer meets the minimum requirements for the software?

  http://www.zuneuser.com/forums/t/softwarefreezesmycomputerordrasticallyslowsit-3673.aspx

• How can I stop my computer automatically after recording a show.

  Original title: Windows Media

  If you are planning a show on the record, that I know that the computer will start up from hibernation, but is it possible to close it after the show is over. I go to bed and do not want to run allnite

  Thank you

  Check the settings here: -.

  Power options > change plan settings > change advanced power settings > media settings >

  Alternatively, you can try: -.

  MC7 Sleep function

  http://thegreenbutton.com/forums/t/79019.aspx

  S.Sengupta Media Center MVP

• How can I prevent the computer to remember logins?

  How can I stop my computer to remember logins? That is, whenever I connect to my webmail, I see all the other associated names of connection with this computer.  Or if I type a letter, all names that begin with that letter pop up.  I want to delete all connection names and prevent my computer; add them to remember in the future.  Thanks for the help =)

  Do you mean the AutoComplete? I remember: IE-> Tools/Options & -tab > content-> AutoComplete

• My computer turns on once a week automatically during the night. How can I stop this from happening? Thanks Gunter

  Hello
  I bought a used desktop computer. After setting it up again to what I had before I find the computer comes on every Saturday night at the same time. How can I stop this from happening?
  If anyone has an answer for me please give him in singles and not "computer language".
  Thank you
  Gunter

  Your best course of action would be to do a complete new installation of Windows.  Not sure how this computer has been maintained or used.  She could have anything whatsoever thereon against malware of illegal material.

  Although the automatic turn on every Saturday night is probably trivial (for example, some application checking to see if there are updates), it could be malware "phone home" with your personal information (bank accounts, passwords, etc.).

  This TechNet article provided by 'Support' engineer is not likely to be useful for you.  For Windows XP (you posted your question in a Windows XP forum), open scheduled as follows:

  Click Start > click on all programs > point to Accessories > tap System Tools > and then click scheduled tasks.

  Review each of the tasks listed to determine what they are doing.  You can then decide if you want to remove one of them.  You should consider, however, that there may be other mechanisms that cause your computer turn on as you describe.