How do you connect a (very) old Apple Airport Express to a new Airport Extreme network?

Similar Questions

• Cannot print with HP6840 since I added the password to the Apple AirPort Extreme network

  I recently added to my Mac Airport Extreme network WPA password protection. While I can access the network from my computer, I can't print a HP6840, one of my two wireless printers, even if there is no problems prior to the addition of password.

  I can always print to my old HP LaserJet 6MP using an AppleTalk-Ethernet bridge and managed to reconfigure my second wireless printer to work with the new password.

  I already tried the following:

  Uninstalled/reinstalled the original CD and more recent software/drivers HP printer

  Tried to printer configuration using the Ethernet - half thanks looking for printer, received an error message "Communication error with a printer" and the installation process has failed.

  Checked: Safari bookmarks / Hello: printer does not appear

  Computer and the printer turned off and restarted the computer

  None of these attempts succeeded.

  Any suggestions on how to restore my wireless printing?

  Thank you.

  MichaelT

  Mac OS 10.5.7 iMac with Intel processor

  I spent 3 hours on the phone this morning with the HP Technical Support. While the call cost me $35, it's probably money well spent. After trying all kinds of approaches to installation, we finally concluded that the villain was probably the combination of personal WPA2 to authenticate password on my network and the inability of the HP6840 printer (now almost 5 years) to support WPA2. Tech said that WPA2 wasn't around 5 years.

  So I have two options: delete the password completely and let my unprotected network, use a WEP password (which can create an Apple AirPort and the printer can recognize) or try a WPA password. However, it seems that the airport offer only WPA-Personal and WPA Enterprise, while the printer does not seem to accept the WPA.

  Even if I don't really relish change passwords again, it seems that WEP is the way to go.

  Hope this helps those trying to install old printers on the new networks.

  MichaelT

• Connection Officejet 8500 for Apple AirPort Extreme

  I have on two devices.  The airport has a network running running.  I plugged the Officejet 8500 at the airport with a network cable.  When you open AirPort Utility, he does not see the printer.  When you use the printer menu, I was not able to find the right method of connection to the network.

  No, you can use (and use) Ethernet.  It's just that Airport utility didn't report it because it is not plugged into the USB port, which is good.

  Now that the printer is connected to your network, download and install the latest version of the software for your printer from the "Support & drivers" link at the top of this page.

• How do you connect as an administrator when you forgot your password?

  How do you connect as an administrator when you forgot your password?

  Original title: password

  Hello

  "What to do if you forget your password Windows 8/8.1"

  http://Windows.Microsoft.com/en-us/Windows/what-do-forget-Windows-password#1TC=Windows-8

  If you have forgotten your Windows password, there are several ways to recover or reset:

  • If your PC is on a domain, your system administrator must reset your password.

  • If you use a Microsoft account, you can reset your password online. For more information, see the Web to reset your password page.

  • If you use a local account, use your index of password as a reminder.

  If you've tried these suggestions and still unable to connect:

  • If you have Windows 8.1, you will need to reinstall Windows.

  • If you have Windows RT 8.1, you will need to contact the manufacturer of your PC.

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  Microsoft prohibits any help given in these Forums for you help bypass or "crack" passwords lost or forgotten.

  Here's information from Microsoft, explaining that the policy:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-security/keeping-passwords-secure-Microsoft-policy-on/39f56ef0-5d68-41AD-9daa-6e6019c25d37

  See you soon.

• How do I register a very old acrobat from adobe and then download the upgrade? It seems that the serial number is not consistent with the serial number required by the adobe Web site. My serial number starts with the letter instead numbers.

  How do I register a very old acrobat from adobe and then download the upgrade? It seems that the serial number is not consistent with the serial number required by the adobe Web site. My serial number starts with the letter instead numbers.

  Please see:

  Redeem your student and teacher edition purchase, convert a redemption code to a number of series and much more .

  I hope this helps.

  Concerning

  Megha Rawat

• After you have reinstalled my old CS6 Design Standard on a new Mac Pro I can't use the updates in help. I only receive offers on update creative Cloud applications. I don't have any application of CC. How to find updates for my applications CS6?

  After you have reinstalled my old CS6 Design Standard on a new Mac Pro I can't use the updates in help. I only receive offers on update creative Cloud applications. I don't have any application of CC. How to find updates for my applications CS6?

  Beginning of the updates here and product selection, read to see if you need to install updates in the order of the numbers, or if updates are cumulative for the product http://www.adobe.com/downloads/updates/

• How to transfer data from an old laptop (broken screen) to a new laptop

  How to retrieve data from an old laptop, to transfer to the new laptop. the problem is that the screen is broken on the old portable th.

  From Internet Explorer

  Original title: data transfer

  The easiest way would be to put his HARD drive in a box that connects to the computer by USB.

  This is just an example - http://www.amazon.co.uk/Hard-Drive-Caddy-Case-Enclosure/dp/B003MVW2SM

  You probably have a 2.5 HDD "because I know that all laptops do.  If you need to buy an enclosure for a 2.5 drive "[not a disk 3.5" that could come from a desktop computer].

  Almost all cases derive the power to drive the HARD drive to the USB itself [rather than an external power].  If you see one that needs an external power supply, then you are probably looking to the wrong thing.

  You need to know if the HARD drive is IDE or SATA.  It depends on the age of the computer.  Your computer's manual should tell you or you can whip the HARD drive just to have a look.

  • Here is an illustration of an IDE - http://www.amazon.co.uk/Generic-Toshiba-Fujitsu-Samsung-Hitachi/dp/B0042WZZD4/ref=pd_sim_147_4?ie=UTF8&dpID=21bYEH0CONL&dpSrc=sims&preST=_AC_UL160_SR160%2C160_&refRID=125C3XKTAFS54XACCCZ8 - connection if you look at the diagrams that you will see that there are long rows of pine trees coming from the HARD disk - what is FDI.
  • Here are illustrations of a connection SATA - http://www.amazon.co.uk/Screw-drive-Enclosure-laptop-Laptop/dp/B003RIL0EM/ref=pd_sim_147_2?ie=UTF8&dpID=419CrJiBX9L&dpSrc=sims&preST=_AC_UL160_SR160%2C160_&refRID=125C3XKTAFS54XACCCZ8 and http://www.amazon.co.uk/drive-Enclosure-laptop-Caddy-Laptop/dp/B00926NM8K/ref=pd_sim_147_9?ie=UTF8&dpID=31sO4aOkykL&dpSrc=sims&preST=_AC_UL160_SR160%2C160_&refRID=125C3XKTAFS54XACCCZ8 - the diagrams show the link inside that connects the HARD drive on [if it's a reflection of what sticks out from HARD drive]-you can see that the connection is a long slot in two sections to the HDD has a long protruding into two sections - which is SATA.

• Presario 2175US not able to connect to the radio after installing Apple Airport Extreme router

  Hi all.  I have a Presario 2175US portable computer that is running Windows XP SP2.  The wireless adapter is a Broadcom 802. 11b / g WLAN adapter.  We have recently installed a router Apple AirPort Extreme in our House, with a network WPA2 key, and while the wireless network is visible on my laptop, when I try to connect, it tries to connect for about 90 seconds, but fails.  Unlike other laptops that we have, it does not ask me to enter the network key before trying to connect.  If anyone has a solution to this problem, I would be very grateful.  Thank you.

  Thanks for the comments, Paul.  I am pleased to say that the problem was solved after I installed the Windows XP SP3.

• Photosmart more B209a-m does not connect with apple airport extreme base station

  I use the B209a-m wireless with a netgear router OS6.  I just changed the Netgear to an apple Airport Extreme router.  All my other hardware connected successfully with the new router but the B209a-m says "no connection found."  I know the printer is well within the router.  I have reset the factory settings on the printer.  I've disabled the system and restarted.  None of this has worked.  Suggestions?

  Hello

  You should not connect it to the airport.

  You must connect the printer with a USB port on your Mac, then run the HP installation wizard.

  From there, you will be guided to provifde the details needed to establish the connection between the printer and Airport Extreme wireless.

  Once the process will be completed and set up the wifi connection you will be guided to unplug the USB.

  You must use a USB cable high speed standard, not longer than 2 m in length.

  The square end must be connected to the USB port located at the back of the printer:

  

• Purchase of 3rd Apple Airport Extreme Base Station

  My current 2 Apple Airport Extreme Base Stations (the two 5th generation) are implemented as shown in the screenshot below.

  My fiber service (80 MB/s) is hard directly on an Apple Airport Extreme Base Station plugged into my home office (via an Ethernet cable that connects from the box of fiber on the outside wall of my house to this AE).

  While AE is hard wired to a 2nd AE in a separate building in my back yard (via an underground conduit of PVC).

  Wired connection that's not a separate Ethernet cable.

  Instead, my provider of fiber spliced in an existing telephone cable that already existed.

  Currently hard connected directly to that 2nd AE in the building separated (via Ethernet cable) are the following:

  My Dell Precision Tower 5810

  My Canon imageCLASS MF6160dw (all-in-one)

  Printer color of my Epson Stylus Pro WF-5190

  (Suite after screenshot)

  

  I am replacing a very old 30 "TV Sony with a 60" LED Smart TV & want to run an Ethernet cable from the AE 1st in my home office to the living room where will be the TV.

  My intention is to add a Roku at the same place than television.

  In addition, I want to increase my wifi signal in the room.

  I know that the Express is 1/2 the cost of the extreme, but will most likely go to the extreme. - If the extreme will give me faster speeds for my Roku and TV.  In addition, I like to have the additional ports available if I ever sign anything else.

  My fiber Service is 80 MB/s Up & Down, but I regularly receive about 96 +.

  80 MB/s is no longer offered by my supplier of fiber, but I'm grandfathered in.

  The available speeds are now 45 (?) with the speed of 100 Mbps.

  I think I'm really on 100 Mbps service.

  QUESTIONS :

  The 2nd AE has been "extended" EI from 1.

  Just as "extend" the 3rd AE?

  For speed best / highest in the living room, the most recent AE should be in the living room next to the TV & the Roku, or he would replace the 1st AE who is in my home office since it is one that is connected directly to the box of fiber on the outside wall of my house?

  Other recommendations will be greatly appreciated.

  The 2nd AE has been "extended" EI from 1.

  Just as "extend" the 3rd AE?

  Yes, either by connecting to the extreme 1... recommended, if possible... .or extreme 2nd... If it is not convenient to connect to the 1st.

  For speed best / highest in the living room, the most recent AE should be in the living room next to the TV & the Roku, or he would replace the 1st AE who is in my home office since it is one that is connected directly to the box of fiber on the outside wall of my house?

  Locate the extreme new... which has a much better arrangement... wireless antenna where it provide the most benefits to nearby wireless devices.

  Otherwise, you might want to consider renaming your airports, because the current device names far exceed the recommended length name a 26 characters max, including spaces. Keep the name short and simple wireless network as well... and to avoid special characters in the name... as an apostrophe, a sign dollar, asterisk, etc..

• HP Photosmart C4795 with Apple Airport Extreme Wireless router - cable PC problem

  Hello

  I searched, but I can't quite find an exact match for my problem.

  I have a new HP desktop computer running Windows 7, and I attach it to my wireless router which is an Apple Airport Extreme.  I have attached my HP C4795 printer to the USB port on the * router *.  In theory, the USB key should pass through, so that the office will think it's a printer "connected", while also allowing us to print remotely from our laptops (via the router).

  Unfortunately, while portable computers can print wireless very well, the * office * Guard 'lose' the printer, thinking that it is in offline mode.  Even when it shows 'online' (after my relocation via "Add a printer"), still error-out print jobs.

  Can someone help me understand how this works?  The printer works fine, btw, if I disconnect the USB cable between the router and plug directly to the PC, if it isn't something directly with the printer or the desktop, but rather the * combination * of running through the Apple Airport Extreme router.

  Thank you

  Terry

  Thank you, once again, Jim.

  I think I have stumbled on the solution.  I did a reading online on Apple application 'Hello', and how he felt necessary for Apple devices, like the airport, knit with device sharing.  I forgot that the installation of the airport disk had said something Hello installation, but I discovered on my Wired HP Win 7 PC menu programs, called 'Hello Printer Utility' or something, and I launched it, selected the C4795 in the dialog box, and all seems to be put in place (i.e. the printer suddenly showed as 'online' and I could print from my desktop wired as well as wireless laptop).

  Success!

  Thanks for all your help on this.  Now, all I need is to get my WD My Book external/sharing the hard drive to work as well!  Unfortunately, I do not see here a "Hello Hard Disk Utility", but I feel somehow that morning will be the answer.  I just understand it.

  Thank you

  Terry

• SG300 combination with Apple AirPort Extreme

  Hello

  I recently bought a SG300 series switch. I want to connect my internet connection in a port of the switch and connect my Apple AirPort Extreme in the switch. So I want that all my other ports on the switch to be put to rout by the airport. Connection Internet and airport to the switch gives you access to the Internet for all wireless clients connected to it. But no switch ports can ping from the airport.

  How can I configure this as simple as possible?

  What I've done so far is to switch the L3 and nothing else. With nothing has changed from the default settings, I was expecting unrestricted access between ports, but appears not to be the case.

  It's my first time, so I expect that it's probably a simple problem.

  I hope someone can point me in the right direction.

  Thank you in advance.

  FR. Lars

  Lars salvation,

  I don't know what is the idea behind connection WAN and LAN to SG300. Is it because you have a single switch, but would need two?

  Also I am not aware how the airport works. Not NAT?

  To add a static route you must navigate Configuration IP--> IP--> Routes IPv4 interfaces and management

  Destination must be 0.0.0.0 IP prefix also 0.0.0.0 if this static route so to access internet.

  Kind regards

  Aleksandra

• Airport Extreme network 4G connection

  I currently have the following configuration for my internet appliances:

  I have an Airport Extreme unit serving wireless three units Airport Express to extend WiFi coverage throughout the House. Physically connected to the Airport Extreme via ethernet are two televisions Panasonic who can access the same places predetermined via the internet (for example, BigPond movies and television, People, ABC iView, SBS OnDemand). To enable connectivity to other sites such as Netflix, Stan etc every Panasonic TV has its own unit of Apple TV connected to Airport Extreme via WiFi.

  I use Airport Extreme for all my other internal needs such as web connectivity MacBook and iPhone.

  The Airport Extreme WAN port is so physically connected to the ADSL modem and line phone Telstra for the Exchange, which is about 4 km.

  The problem is that the speed of download of the ADSL 2 + are poor, maxing out at about 3.5mbps. When I listen to the live broadcast of MotoGP and World Superbike racing the picture often freezes while he puts in buffer. Watched movies via Netflix and Stan often freezes too.

  I just ran a speed test on the Telstra Mobile 4 G network and I got a download speed of 111.94Mbps 41.77Mbps upload speed.

  Now, I'm thinking it would be great if I could connect my home network to the internet via their WiFi 4 G device X Pro Advanced.

  My question is this:

  Is it possible to connect the Airport Extreme to the Telstra WiFi 4 G device and the use of the mobile network for my internet and get rid of the ADSL modem? I don't think I can use USB Extreme airport connection, I think that the port is only to connect a printer, but I do not know if the Airport Extreme talk wireless Telstra 4 G device. Documentation of Telstra said their device will connect up to 10 devices using WiFi, but I do not know if there would be problems with the Airport Extreme router to talk to her.

  After spending heaps on all these units of Apple (1 x Airport Extreme) and 3 x Airport Express I don't want to lose, but if there is no way to Airport Extreme wireless unit of Telstra (or if this method is ridiculous) so maybe I might be able to get the device of Telstra to talk to all my other WiFi devices directly. Then, I might be able to sell the extreme and expresses it.

  I had a discussion with Apple Support through their chat session, but the person with which I spoke was not able to help.

  Thanks in advance.

  You need a device that is able to connect via Ethernet to the AirPort Extreme base station.

  With a plain/direct USB 4 G modem, a router broadband mobile sometimes can act in Bridge mode and thus provide a conversion method. For example, Dovado has these routers, but their modem (http://www.dovado.com/en/support/modems) compatibility list appears to cite that a single Telstra USB 4 G modem (ZTE) which supports the mode bridge.

  Your question indicates, however, that the 4G modem is actually a mobile access point (providing a local Wi - Fi network). If so, it may or may not be possible to use the wireless Ethernet Bridge (maybe even a model of Apple AirPort Express appropriate) to join this hotspot wireless and then connect via Ethernet to the entrance of the AirPort Extreme. This is all experimental, however. Various problems, including double NAT, are to be expected.

• WAG160N and an Apple Airport extreme

  I recently bought an Apple Airport extreme, and in order to use the guest account, I need to disable DHCP and NAT on my WAG160N settings and allow extreme settings. Otherwise the extreme is in bridge mode and therefore doesn't let me create a guest account.

  Could someone tell me please what settings I need to change in the WAG160N so that it acts as a modem only and not a router.

  Thank you

  You can't disable NAT on the WAG unless you go to fashion of the bridges, which means that it becomes a simple modem. You cannot use the wireless on the WAG, nor anything else. In bridged mode, you configure Airport Extreme as main router connecting to PPPoE (or whether you need from your ISP).

  Switch mode bridge on the main configuration page.

• ARE remote with Apple Airport Extreme router wireless

  Hi all! I'm controlling my DA5800 STR using the Remote ES app but neither my iOS device sees the receiver OR my Sony Android Tablet S. So I figure it must be the network set up. I use a cable modem Motorola connected to an Apple Airport Extreme via an ethernet cable. The receiver is connected to the router, as shown in the manual.

  I'm doing something wrong here?

  Thanks in advance for any help!

  Hello Sandiegodom,

  Please check the network settings on the receiver ARE and confirm that the 'external control' is active, as well as the "relief network" that will allow the application ARE the 'waking up' the unit from standby mode.

  Also check that your phone is connected to the same wireless network, and IP addresses of the phone and the receiver are in the same subnet / IP Range. UpNp must also be enabled in the settings of the router.

  If you have verifed that these settings are correct, then the question is perhaps with the router where it does not send data to the local discovery of uPnP network devices. A simple power reset or resetting the router will sometimes force the router to send back data and should fix the problem if that is the case.