How downgrade Tecra S10 to Vista?

Similar Questions

• Tecra S10-128-Vista 32 - eSata does not work?

  Hello everyone,

  I have 2 external hard drives USB\eSATA, an AKASA 3.5 and a VANTEC 2.5, they work fine in USB mode, but in eSATA, I get no response from the TECRA S10-128.
  The wealthy drive 3.5 does not need external power, the 2.5 power, when I connect the cable, is not a led flash.

  The OS is 32-bit previously connected original Vista.

  All ideas, King regards,
  FERRETE

  Now, I realized that the Tecra S10-128 is sold only to the Portugal! Here you can see what losing bean you'v: p.

  http://PT.computers.Toshiba-Europe.com/innovation/product/Tecra-S10-128/1060596/toshibaShop/false/
  .

  .

  Hello

  > They work fine in USB mode, but in eSATA, I get no response from the TECRA S10-128
  I was a little confused m
  As far as I know that the laptop supports the eSATA/USB combo port it s on the left and it conforms to the USB 2.0 standard.

  A (HDD) connected eSATA device cannot be recognized unless it s connected to the eSATA port, while the phone is in standby or standby.
  In this case, disconnect the eSATA device and reconnect it while the Tecra is turned on.
  Usually, it takes about 10 seconds until the eSATA device would be recognized by the laptop. Don t try to disconnect and reconnect the drive before this period has elapsed.

  In your case, I would check the BIOS settings.
  The second page of the BIOS provides eSATA settings. Check it out.

  I also recommend the installation of the OS switching device Configuration.
  This can be done as well in the BIOS

• Tecra S10 - 11W: how to uninstall Win XP SP3

  I have successfully completed my Tecra S10 - 11W from Vista to XP with the recovery CD
  But since XP SP3 (had) problems with some software I want to uninstall it and install SP2.
  But even with the information from the Microsoft Web site, I was unable to uninstall SP3!

  Hello

  I put t know if it would be possible to remove the SP3 if it was not previously installed.
  But I found that MS document:

  + How to remove Windows XP Service Pack 3 from your computer.
  http://support.Microsoft.com/kb/950249

  Perhaps, it might be useful.

• Tecra S10-106 - 3 G driver for Vista Ultimate 64-bit

  Hello

  I own a Toshiba Tecra S10-106. Due to the fact that Vista Ultimate 64 bit is much faster than Vista Business 32-bit, I would use Vista ultimate 64-bit operating system, but I can't find the 3G for Vista 64-bit driver. All the drivers can be downloaded from the USA in English and can be used in German, only the 3G driver is missing. Can someone send me a download link or tell me where I can find a driver for Vista-bit 66?

  Thanks in advance.

  Hello

  You can download the drivers here:

  http://Support1.toshiba-tro.de/Tedd-files2/0/3gdrv-20090303131409.zip

  64-bit drivers are located under the Portégé R600 laptop.

  Concerning

  Phil

• Tecra S10 - 64 bit of Vista and Win7 64 bit driver question

  Hello

  I own a Tecra S10 and using Vista 64-bit operating system.
  Unfortunately Toshiba isn't supporting this version of the OS, because pilots proposed must be taken on different products that use the same hardware.

  Is anyone know wether Toshiba will start sharing the drivers for Vista 64 bit soon and whats on Win7?

  I think that Vista 64-bit drivers will run under Win7, but * when they officially released drivers for 64 bit Vista or Win7?

  Any info would be interesting.

  Thanks in advance.

  Hello!

  Normally it comes out drivers * after the release of the operating system. This means you have to wait a few months more I think
  But you think contacting Toshiba? Guys, you should know better than us users here. If you write an email or call, it takes only a few minutes!

  In addition, you should try the Vista 64 bit drivers. Most of them also works under Windows 7.
  And it s worth a try! ;)

  Good bye

• Tecra S10-142 - how to fix touch Assist from Toshiba?

  I have a Tecra S10-142, with Windows XP.

  The * Toshiba assist button * does not work because this utility is not loaded at startup.
  What can I do to fix it? Where can I find the drivers to install this utility?

  Thank you

  Hello

  I agree with the user above. You must install or reinstall Toshiba Assist, which can be downloaded from the Toshiba page.

  The installation should be performed in a few clicks only, and maybe you have to restart the laptop. After that, it should work.
  Can you confirm this?

• Tecra S10: undefined screen with a resolution of 1280 x 800

  Hi all,

  I have a strange problem with the resolution of my Tecra S10.

  My system:

  * Windows Vista, later lowered to Windows XP SP3 with the last update
  * Latest Toshiba nvidia drivers

  My default resolution is 1680 x 1050 initially and the display is sharp and perfect proportional to the screen (15.4 ", 16Million color), even if the icons are quite small.

  I changed my resolution of 1280 x 800 using the steps described in the user manual. But the screen is fuzzy and ill-defined.
  According to the manual of Toshiba (Tecra S10 Satellite Pro S300) my NVidia video card supports the resolution of 1280 x 800 WXGA mode.

  How can I put mode WXGA?

  I appreciate all suggestions that solves the problem.

  Best regards
  Biagio

  Hello

  To be honest you write on this is certainly not a problem but something usual for views. The display will be sharp and perfect when you set the view to the native resolution only.
  If you choose some other low or high resolution the illustrious office will be either too big (does not fit in the display) or will be blurred.

  The same situation is on my Tecra M1. Test it on all laptops, and the situation will be the same. I'm now working on Satellite P200 with 17 inch screen. For this display's native resolution is 1440 x 900.
  When I reduce the resolution the office is always fuzzy and ill-defined.

• Need driver disc to install Windows 7 on Tecra S10

  Hello

  I have a Tecra S10 - 11I with Windows Vista and I buy the seven Windows Update but when I try to install it, a message told me to install the driver from the cd/dvd drive (it is a Teac DV w28s-rt) and can't find it, can someone give me the link to download it or show how I can install windows 7 on my pc

  Thank you. (Excuse me for my English)

  For disk drive optical feature you n t need to install an additional driver.
  You can use your optical disc drive, the usual use of DVDs and CDs?

  Can you maybe send a screenshot of this message?

  As far as I know when you start the upgrade (upgrade disc put in ODD) you should see THE menu.

• Tecra S10 - problem upgrading to SSD Kingston

  Hello!
  Tecra S10 - I am trying to upgrade HDD to Kingston SSD 128MD.

  During the new installation of Windows 7-64 installer complains that there is no boot device valid to create the system partition, even if the disk is recognized. BIOS is later, I tried configuring IDE and AHCI.

  Is there a problem of General compatibility with SSDS and the notebooks?
  I noticed a similar problem with satellite A200.
  Thank you

  Hello

  How do you update firmware?
  Have you checked if a firmware update is available and necessary?

  Found a page of Kingston providing SSD firmware updates:
  http://www.Kingston.com/en/support/technical/downloads?product=sv100s2&filename=KDID110225a

• Can Tecra S10 - I order a recovery to another disk?

  Someone knows how to change the language of Windows 7 on a Tecra S10?
  Can I just order a recovery disc Englsih from here:
  [https://backupmedia.toshiba.eu/landing.aspx]

  If so, what is the price of these discs?

  The PC has a license for the preinstalled Windows 7 Pro 32 bit German, and I need it in English.

  Hello

  I doubt that this will be possible.

  You can order the recovery disk only with the same Windows operating system which was preinstalled on your laptop.

  If you need a different language of Windows or another version of windows, then you will need to purchase an original MS Windows disc.

  This means that you will get the new clean operating system, drivers may be downloaded from the page of European driver of Toshiba.

• Re: Tecra S10 disorders with drivers

  Hey

  I have on my Tecra S10 (PTSB3E) Windows 7 64 bit installed.
  In Device Manager, I have the "PCI Communicationscontroller" without the appropriate driver. What I have to do, that this element gets the correct driver?

  A Secoud problem is with my docking station. I have the PA3680E. When I have my S10 anchored on the station, I have another device without the correct driver. The USB-serial controller. Also the fingerprint reader - Gets an error when I run the application.

  Can someone help me get the correct insalled in the system?

  Thank you
  Thomas

  Hello

  Who knows what you have installed and what are the missing drivers.
  Here is the order of installation for your computer laptop tecra. Check it out to see if everything is installed or not:

  Win7
  Chipset utility
  Matrix Storage Manager
  TOSHIBA Value Added Package
  Installation of the PVAT button setting
  Display driver
  Realtek HD Audio Driver
  ALPS Pointing-device Driver
  TOSHIBA software modem
  Driver LAN (EnergyStar support)
  Wireless LAN driver
  Bluetooth Stack for Windows by Toshiba
  Intel AMT Management Engine Interface
  RICOH Media Driver
  O2Micro smart card reader driver
  TOSHIBA SD Memory utilities
  TOSHIBA SD Memory Boot Utility
  Logon Key TOSHIBA wireless
  180 degree TOSHIBA Rotation utility
  TOSHIBA HDD Protection
  TOSHIBA ConfigFree
  TOSHIBA WPS library
  TOSHIBA management console
  TOSHIBA Assist
  TOSHIBA security assist
  Pilot TRS for study
  CD/DVD Drive Acoustic Silencer
  Infineon Trusted Platform Module utility
  Infineon TPM (Trusted Platform Module) installation guide
  AuthenTec fingerprint utility
  Chicony Camera Assistant Software
  TOSHIBA face recognition
  TOSHIBA SSD alert
  TOSHIBA PC Health Monitor
  TPCHFsDate.exe for PC Health Monitor
  TOSHIBA cooling Performance diagnosis
  TOSHIBA Consumtion wattmeter
  Sleep USB TOSHIBA and service charges

  All orders must be installed in that order. If missing some driver on this list try please install the driver for Vista 64 bit.

• Tecra S10 - unrecognized Usb device

  Whenever I plug the mouse usb Tecra S10 - 11A I get the message "unrecognized (or due to a malfunction) Usb device". Then, after several times of rehearsals to plug / plug everything is OK. But after each reboot, I must repeat plug/plug in mouse for several times.

  Now, I'm on Vista, but it is even on Windows 7 or XP.

  Is it possible to solve the problem?

  Thank you!

  Hi gordan84,

  Have you installed a 3rd party software/driver for the external mouse? If Yes, you should remove it.

  This happens with other USB devices like printer too?

  Maybe a BIOS update could be useful, you can download it on the Toshiba site.

• Tecra S10 - 10F - Support Button Multimedia problem

  Hello

  I have Toshiba Tecra S10-10th with Win Vista SP2.
  I have problem with Toshiba button Support.
  After a clean install of Vista, everything works fine. Now two buttons next to the button toshiba walk / stop don't work. When I uninstalled 'toshiba value added package', buttons was answered but open "windows Mobility Center.

  When I installed Toshiba value added Pachage once again, the buttons are no longer...

  Could someone help me pls?

  THX

  Hello

  This strange s
  Usually the installation of VAP should help you get the buttons working again.
  Value added package contains tools and utilities that are necessary for the functionality of the multimedia buttons

  Please install the VAP, and then configure the keys still using the utility button Toshiba located in Toshiba Assist-> optimize

  There you have to click on the button, and then you set some for some exe file button.
  Single exe files are in C:\Programs\Toshiba\TBS

  Welcome them

• Tecra S10 - e-SATA with WD MyBook problem

  I have Tecra S10-10 loaded with win 7/32 final. From the beginning, there is fixation e-sata WD MyBook problem - most of the time cannot be reached
  and Device Manager hangs up refreshing devices. Only restart after sometimes he can be attached, but only those by boot allows. All other devices works fine. Before win 7
  I worked with XP no problem also.

  I tried to update the drivers for the chipset for win 7 - but it failed with the message that this computer does not meet the minimum requirements.
  The BIOS is 2.0. Trying to upgrade the BIOS to 3.0, he replied that Intel TXT must be disabled, but it is set in the BIOS, option cannot be selected.

  No idea how to fix e-sata?

  Hi Damir

  As I see that you do have a general problem with e-SATA, but just when you want to use this device to some so I think that the solution is not so easy.
  This device is not known to me, but I suppose you guessed it with USB cable. You can use it with any other standard USB port?

• Hibernate does not work on my Tecra S10-101

  Hibernate does not work on my new Tecra S10-101. I searched the internet but
  has not found a good solution. Cuisne someone provide help to solve this problem?

  Kind regards

  Bert

  Please explain the problem more.

  What do you mean by "does not?

  You can enter at least hibernation?
  Pick up from the hibernation failure?
  Hibernation is missing in power options?
  Are you running XP or Vista?
  What Service Pack you have installed?
  Did you install your own version of Windows or is - what a correct installation of Windows from Toshiba?