How many interfaces in asa 5510

Similar Questions

• How to upgrade an ASA 5510/20

  I have several ASA 5510 and 5520 requiring an update and I tried to find a way to automate the process. Many of the features are running in active/active mode (primary is active and the secondary is in standby mode).

  I'm looking through the ADSM features and I found the automatic update. This looks like a good way to go because he downloaded the software for primary school and then transfers her back to the secondary device. It then performs the update device 1 both starting with the secondary device. But he said: I need a server was updated to contain the new software and I do not know how to create a. I have a machine that a FileZilla server is installed, but that uses FTP and the Automatic Updates settings are looking for an HTTPS address.

  The other option I havea Cisco first Infrastructure 2.0 is available. I can use this to manage the software, but there is nothing on how to use it with an ASA installation as an HA pair.

  I could use any help you may have.

  Cisco Security Manager is more generally used as a server update for large deployments ASA.

  PI 2.0 is a little rough around the edges on its support of ASA, and I would judge not quite ready for this task. (It is same with the package update of December 2013, which increase the support of the ASA).

  Depending on your version, most people are not comfortable with auto update of firewalls. Things have changed considerably with post-8, 2 and all migrations I've ever done that (TENs) involves a manual check of the new syntax and operations.

• How many group Supportepar ASA 5520 vpn for remote access

  Hello

  Howmany vpn group is supported on asa 5520 with configuraion vpn remote access.

  Concerning

  1 if nat-control is disabled and you do not have any other order NAT in your config file, you do not have it. Try to remove the existing "NAT 0" command and "clear xlate."

  2. you must ensure that your network inside know they can go by ASA to access remote vpn client IP. You have any device layer 3 behind the ASA that does the routing. If so, please verify that this is the routing table.

• How many switches must be configured and min no network interface cards?

  Hello

  We will implement the ESXi5.0.

  We would like to know if we use different ports for network management and vMotion groups?  It seems that two of them use the same (different from ESX 4) IP address.

  In addition, my supervisor would like to know what is the minimum number of network interface cards to use (because the server has no slot PCIe)?

  Your opinion is requested.

  Thank you

  TonyJK wrote:

  Since we implement VLANS on our site and based on the documentation, ESXi 5 gets only 1 battery IP, wonder what is the best way to cope.

  It is true that ESXi has that one battery IP, which is very good compared to the other two in ESX (Linux in the Service Console and the Vmkernel). However, we have only an IP stack means that it is the same driver tcp/ip, but does not mean that we cannot have multiple IP addresses.

  For example, you can create a Vmkernel how many interfaces you want and assign different IP addresses, which could be on the same network or on different.

  Even if you don't have a VLAN in your environment I would still recommend using another IP network for vMotion for your management. This will make the two a little more 'best practice', easier to different and you would be good too preperred if you implement VLANs in the future.

• ASA 5510 Configuration. How to set up 2 outside the interface.

  Hello

  I have Cisco ASA 5510 and the desktop, I want to create a new route to another (external) router to my ISP.

  The workstation I can Ping ASA E0/2 interface but I cannot ping the router ISP B inside and outside of the interface.

  I based my setup on the existing configuration. which so far is working

  interface Ethernet0/0
  Outside of the interface description
  nameif outside
  security-level 0
  IP 122.55.71.138 address 255.255.255.2
  !
  interface Ethernet0/1
  Inside the interface description
  nameif inside
  security-level 100
  IP 10.34.63.252 255.255.240.0
  !
  interface Ethernet0/2
  Outside of the interface description
  nameif outside
  security-level 0
  IP 121.97.64.178 255.255.255.240
  !

  Global 1 interface (outside)

  global (outside) 2 interface (I created this for E0/2)
  NAT (inside) 0 access-list sheep

  NAT (inside) 1 10.34.48.11 255.255.255.255 (work: router ISP inside and outside interface E0/0)

  NAT (inside) 2 10.34.48.32 255.255.255.255 (work: E0/2 router ISP on the inside interface only but cant outside ping).

  Route outside 0.0.0.0 0.0.0.0 122.55.71.139 1 (work)

  Route outside 10.34.48.32 255.255.255.255 121.97.64.179 1 (the new Road Test)

  Router ISP, that a job can ping and I can access the internet

  interface FastEthernet0/0
  Description Connection to ASA5510
  IP 122.55.71.139 255.255.255.248
  no ip redirection
  no ip proxy-arp
  IP nat inside
  automatic duplex
  automatic speed
  !
  the interface S0/0
  IP 111.54.29.122 255.255.255.252
  no ip redirection
  no ip proxy-arp
  NAT outside IP
  !
  IP nat inside source static 122.55.71.139 111.54.29.122
  IP http server
  IP classless
  IP route 0.0.0.0 0.0.0.0 Serial0/0

  FAI 2

  interface FastEthernet0/0 (SAA can ping this interface)
  Description Connection to ASA5510
  IP 121.97.64.179 255.255.255.248
  no ip redirection
  no ip proxy-arp
  IP nat inside
  automatic duplex
  automatic speed
  !
  interface E0/0 (ASA Can not ping this interface)
  IP 121.97.69.122 255.255.255.252
  no ip redirection
  no ip proxy-arp
  NAT outside IP
  !
  IP nat inside source static 121.97.64.179 121.97.69.122
  IP http server
  IP classless
  IP route 0.0.0.0 0.0.0.0 E0/0

  CABLES

  ASA to router ISP B (straight cable)

  Router ISP in the UDI (straight cable)

  Hope you could give some advice and the solution for this kind of problem please

  Hello

  Are you able to ping the router IP of the interface of the device of the ASA? If so, try a trace of package on the device of the SAA for traffic to the IP address of the router.

  Thank you and best regards,

  Maryse Amrodia

• Allow specific access through the Interfaces ASA 5510

  Hi all

  In my quest to learn Cisco IOS and devices, I need help in smoothing traffic, or access lists, allowing traffic between internal interfaces on the SAA specifically.

  I have an ASA 5510:

  WAN/LAN/DMZ ports labled E0/0 (LAN), E0/1 (WAN), E0/2 (DMZ).

  Connected to the port E0/0 is a 2811 router

  Connected to the port E0/1 is the (external) Internet

  Connected to the port E0/2 is a 2821

  (I'll add a 3745 for VOIP) port E0/3, but it has not yet happened.

  I want to allow traffic between the 2821 and the 2811 routers so that devices on the networks behind them can talk to each other.

  I've specified specific subnets between the ASA and the routers because I want to learn how to shape traffic behind routers, as well as on the ASA. So behind the routers I have different VLANS, but I'm not restrict access between them, still, at least I don't think I am. But as it is, behind the 2821 devices cannot access the DNS / DOMAIN SERVER that is located behind the 2811. Right now I have the routers DHCP power, who works there. Currently devices behind the router 2821-3560 switch cannot access the domain server, primary dns server.

  How can I set the ASA to allow traffic to flow between the two routers and their VLANS?

  Here's the configs of each device and I have also included my switch configs, incase something should be set on them. I only removed the passwords and the parts of the external IP address. I appreciate the help in which States to create and on which devices.

  I think it is best that I put the links to the files of text here.

  Thank you!

  You must remove the following statements on the two routers:
  -# ip nat inside source... overload
  -for each # ip nat inside/outside interface, if they have configured.

  Remove ads rip of the networks that are not directly connected:
  -2821: 172.16.0.0, 192.168.1.0, 199.195.xxx.0
  -2811: 199.195.xxx.0
  -ASA: 128.0.0.0

  No way should be added to the routers, since he is the one by default, put in scene to ASA.

  Check the tables of routing on routers and the ASA.

  On ASA:

  -Remove:
  object-group network # PAT - SOURCE
  # nat (indoor, outdoor) automatic interface after PAT-SOURCE dynamic source

  -create objects of the networks behind the LAN router and enable dynamic NAT:
  network object #.
  subnet
  NAT (inside, outside) dynamic interface

  -review remains NAT rules.

  -to set/adjust the lists access penetration on the interfaces. Do not forget to allow the rip on the LAN and DMZ interfaces.

  -Disable rip on the outside interface.

• Cisco ASA 5510 L2L VPN on the backup interface

  OK, here is what I have and I even if I knew how to do this, but it has not worked for me.  I hope someone out there can help you.

  I have an ASA 5510 running 8.4 with double configuration of ISPs on 2 different interfaces: outside (primary), backup (backup).  I also have a site to site VPN ASA another in another city.  The VPN is now configured on the external interface and works very well.  What I wanted to do, is to make the VPN running on backup interface only.

  So, I changed the card encryption on the remote side to use the backup interface IP and created a tunnel-group for her.  Then, I created a map encryption for backup interface and activated ikev1 on it.  The default route is configured to use the external interface, so I created a static route that routes traffic destined for the external interface of the remote side to the backup interface default gateway.  I can get to establish tunnels, but no traffic passes through them.  I have however while I need a NAT device for the tunnel traffic to I created a NAT so but still no transmitted traffic.  I tried the packet - trace and he said: the traffic was allowed and show its crypto ipsec command, I see the configuration of the tunnel, but no traffic will pass through it.  Can anyone help?

  Ben,

  you use a code to version 8.4, I recommend starting by removing the config NAT statements at both ends. This version does not have the NAT and control, and if you don't need... I've seen instances with 8.4 (3) where a NAT even though apparently correct was causing not to pass through the traffic.

  Site A:

  NAT (inside, backup) source static obj-SiteALAN obj-SiteALAN static obj-SiteBLAN obj-SiteBLAN

  Site b:

  NAT (inside, outside) source static obj - 192.168.5.0 obj - 192.168.5.0 destination static obj - 192.168.3.0 obj - 192.168.3.0

  If possible, you should increase your AES encryption, but this is a personal point of view and should not stop the traffic through the links. You should be able to see the counters for the data transmitted / received are these incrementing?

  Do you have the ACLs that are from the inside to the outside and internal interface to the Interface of backup (duplicated.

  In this model, the control is the routing.

  Best regards

  Ju

  http://helpamunky.WordPress.com/

• LaserJet P1102w: History of how many pages each toner printed in web interface?

  Is it possible to find in the web interface for the printer, a story of when a new toner has been inserted, and how many pages it had printed upward? I know how to access this story, but from what I can tell, it only shows the current number of toner and the page.

  
  HP LaserJet p1102w

  Hi @paulri,

  I understand that you want to know the history of how many pages have been printed of each toner. I'd love to help you.

  You can print a Configuration report to get the total number of pages printed from the printer, but not individual toners.

  Printing a Configuration Page. Select the method two.

  Feel free to click on the button under the thumbs up if it helps.

  Good day!
  Thank you.

• How default context in plsu security edition asa 5510

  Hi could someon pls tell me with the edition of security plsu asa 5510 it will support active/active failover. and she supports context with securiyt plsu edition. and how default context do we receive with edition of plsu security asa 5510.

  concerning

  Assane

  Hello

  By default, ASA5510 with Security Plus comes with default 2 security [email protected] / * / firewall. Context of maximum security, you can have (upgrade to) is 5.

  With license upgrade of security Plus, you might have active/active and active / standby (choose one to run at any time) high availability services.

  http://www.Cisco.com/en/us/products/ps6120/products_data_sheet0900aecd802930c5.html

  Rgds,

  AK

• How to activate IP accounting or capture packets in Cisco ASA 5510 (8.2)

  Hi all

  Please help me for activation

  IP accounting packets or capture in Cisco ASA 5510 (8.2).

  Thank you

  Solene

  Hi Eric,.

  Create a list of access with the source destination ip address and/or tcp/udp ports

  can use it

  CAP_NAME access-list ACL_NAME buffer 12345bytes INT_NAME capture interface

  You can check capture

  See the capture?

  Name Capture PASSWORD

  |     Output modifiers

  Take care

  PaulC

• in my cisco asa 5510 heartbeat interface

  Cisco asa 5510 heartbeat interface

  Of course, we will need to more information than what you have given to us. Next time, don't even bother if you want to help us...

• ASA 5510 - level security Interface

  I have an ASA 5510 (8.2.1 code). I'll implement the separat IPSec tunnels two remote networks, but each remote connection to an ASA respective interface.

  Question: I know that the e0/0 ('outside') security level of the interface is 0. However, only the second interface e0/2 ("out2") security level must be set to 0 as well?

  Thank you

  Jim

  Yes you can, simply apply the respective crypto map to the interface. You might want to do e0/2 and e0/3 the same level of security (if your security policy allows) and same-security-traffic permit inter-interface. Which allows communication between the various interfaces that have the same level of security. You can ignore the NAT mess.

• How to enable routing on a subnet in ASA 5510

  Dear Sir

  We use cisco ASA 5510, and we provide access to external users through cisco anyconnect VPN. When users connect, they can access a single subnet. How can afford to drive to another subnet CLI or ASDM?

  Thank you best regards &,.

  Hello

  Seems to me that you have not at least have a NAT0 configuration for traffic between the LAN subnet and VPN pool

  This is your current NAT0 ACL configuration

   access-list nonat extended permit ip 172.16.0.0 255.255.254.0 172.16.2.0 255.255.255.0 access-list nonat extended permit ip 172.16.0.0 255.255.0.0 172.16.0.0 255.255.0.0 access-list nonat extended permit ip 172.16.0.0 255.255.0.0 host 10.212.61.32 access-list nonat extended permit ip 172.16.0.0 255.255.0.0 172.16.0.192 255.255.255.192 access-list nonat extended permit ip 172.16.0.0 255.255.254.0 10.1.12.0 255.255.255.0 access-list nonat extended permit ip 10.1.12.0 255.255.255.0 10.1.12.0 255.255.255.0 access-list nonat extended permit ip 172.16.0.0 255.255.0.0 10.1.12.0 255.255.255.0 

  Pool of VPN you seems to be 172.16.240.0/24, so you must add the following line of ACL

   access-list nonat extended permit ip 10.1.12.0 255.255.255.0 172.16.240.0 255.255.255.0 

  Hope this helps :)

  -Jouni

• ASA 5510 - possible to fill the 2 interfaces in routed mode

  Cisco ASA 5510 with security more license, version 9.1 (5) running in routed mode.

  I want to fill two interfaces for example: eth0/2 and 3/eth0 and configure an IP address / network while leaving the ASA 5510 in routed mode. I know that this is possible in transparent mode, but I need to keep this in routed mode. I know I could configure a single interface and connect a switch but my client does not want to do.

  Otherwise, my only thought would be to configure each interface eth0/2 and eth0/3 as a network traffic and the route of subnet separate between the two.

  Any help would be appreciated!

  Thank you

  Andrew

  Andrew

  That would help us answer you better if we understood more about what your client and you want to accomplish. But to answer the specific question you asked, I don't think it is possible in an ASA5510 in routed mode configuration Eth2 and Eth3 to share a single IP address.

  Linking to Eth2 and linking to Eth3 Are they really the same subnet?

  HTH

  Rick

• How can I hold the public IP address on a specific profile on the asa 5510

  Hi guys

  How can I hold the public IP address on my session NAT VPN cisco customer for no one else can use it? I have a cisco ASA 5510

  the Interior is 172.10.20.86

  public 166.245.192.90

  Need to call my ISP?

  Thank you

  Sorry to say but your qustion is not very clear. Can you please post what you are trying to achieve?

  Thank you

  Ajay