How much max VPN session is my ASA
This is my version to see the ASA5512 VPN
"Other peers VPN: 250" means that I can use 250 IPSEC session? If I still use MAX 250 VPN Cisco AnyConnect Secure Mobility Client session?
"Total peer VPN: 250" means that I can use 2 Anyconnect premium + 248 250 IPSEC or IPSEC session at the same time?
"AnyConnect for Mobile: Disabled" means, I can't use AnyConnect Secure mobility Client (smartphone apps) connect to the ASA by AnyConnect SSL? Can I use AnyConnect secure mobility Client (smartphone apps) connect to the ASA by IPSEC?
The devices allowed for this platform:
The maximum physical Interfaces: unlimited perpetual
VLAN maximum: 100 perpetual
Guests of the Interior: perpetual unlimited
Failover: Active/active perpetual
Encryption - A: enabled perpetual
AES-3DES-Encryption: activated perpetual
Security contexts: 2 perpetual
GTP/GPRS: Disabled perpetual
AnyConnect Premium peers: 2 perpetual
AnyConnect Essentials: Disabled perpetual
Counterparts in other VPNS: 250 perpetual
Total VPN counterparts: 250 perpetual
Shared license: disabled perpetual
AnyConnect for Mobile: disabled perpetual
AnyConnect Cisco VPN phone: disabled perpetual
Assessment of Advanced endpoint: disabled perpetual
Proxy UC phone sessions: 2 perpetual
Proxy total UC sessions: 2 perpetual
Botnet traffic filter: disabled perpetual
Intercompany Media Engine: Disabled perpetual
The IPS Module: Disabled perpetual
Cluster: Disabled perpetual
THX
Hello!
ASA5512 can contain up to 250 concurrent VPN of any type: IPsec Site to Site or IPsec Remote access or Anyconnect SSL VPN or IPsec IKEv2, or even without VPN client.
This means you can use 2 Anyconnect premium + 248 IPSEC VPN from Site to Site. Or, for example, 200 simultaneous IPsec Site to Site VPN + 25 Client VPN (IPsec IKEv1) + 25 AnyConnect VPN (SSL or IPsec IKE v2). But not more than 250 and then at the same time.
"AnyConnect for Mobile" is now obsolete. The license for Anyconnect schema was changed in early 2015. You can see the new pattern here:
http://www.Cisco.com/c/dam/en/us/products/security/AnyConnect-og.PDF
With the new scheme, if you need to connect mobile devices (iOS, Android and so on), using the Anyconnect client, you just need to have a license Anyconnect MORE for the necessary amount of users/devices. License AnyConnect more open along the lines in the output of the show version:
AnyConnect Premium Peers : 250 perpetual
AnyConnect for Mobile : Enabled perpetualAnyConnect for Cisco VPN Phone : Enabled perpetualAdvanced Endpoint Assessment : Enabled perpetualBut, despite the exit "AnyConnect peers Premium: 250 perpetual", you will have the right to use no more then amount ordered... If you need advanced features, for example, Suite B cryptography or VPN without customer, you must order license Anyconnect Apex for amount of users/devices needed. For ASA5512, you need to order licenses Anyconnect more or Apex, but no more so for 250 users, because ASA5512 can't take no more then 250 simultaneous connections. If you want to use the Anyconnect client for mobile devices and you use IPsec IKEv2 for VPN, you will also need order licenses Anyconnect more or Apex. I hope this helps.
Tags: Cisco Security
Similar Questions
-
AC VPN: vpn-session-timeout and prompt the user
Hello
Is it possible to invite the user to continue the session shortly before it hits the vpn-session-timeout value (ASA).
Thank you
Sean
Sean,
I believe that no job like this been done on it by the BU.
We had this never open a:
https://Tools.Cisco.com/bugsearch/bug/CSCsx17267/?reffering_site=dumpcr
M.
-
ASA VPN - how much IP address?
If anyone can help on this configuration of the DMZ? This is taken from the book. If the firewall of the ASA has a public IP (209.165.201.225) on the external interface, then on my router? This means that I need 3 public ip address? ISP-(adsl with public ip) [b] ROUTER [/ b] (fa0/0 209.165.201.226)---(outside=209.165.201.225)[b]ASA5505[/b](inside=192.168.1.1) the router route providing the PUBLIC ip address of the ASA outside intellectual property (how one translation)? I know by ASA will need a translation of outside DMZ and with an access list to allow traffic. Right now, my company only has a public IP address. How can I make this work? Thank you!.
Hello
If you have a public IP address unique usable, you can have this IP address on the router (internet gateway) and have a segment between the router and ASA.
By port forwarding, you can have incoming traffic sent to the ASA by the router (such as VPNS, for example).
The ASA will not need a public IP address that is configured on the external interface as long as the device with the public IP (router) can redirect traffic to private IP assigned to the WAN of the ASA interface.
Hope that makes sense.
Federico.
-
ASA 5505 VPN sessions maximum 25?
Hello friend´s
The company I work when acquired several ASA 5505, so now we will be able to connect several branches at Headquarters. But, now, I know that the ASA 5505 just scalates to 25 VPN sessions, I think that it won´t be enough to support the operations of an office. I have a lot of questions about this:
Is - what the number 25 menas supporting up to 25 L2L tunnels? Or it means 25 sessions, regardless of the amount of L2L tunnels?
Is this the way number 25 supporting up to 25 users in the Branch Office? Or it means that a user can use several sessions?
I'm the stage of testing in a laboratory where one PC connects to many applications, at - it now someone if there is a command in the SAA to check how many VPN sessions is used?
Please, do not hesitate to ask as much as necessary information. Any comments or document will be appreciated.
Kind regards!
Hi Alex,
The assistance session 25 ASA 5505 VPN as max for IKEv1 or IPSEC tunnels customers it could be up to 25 L2L tunnels or 25 users using ikev1 (Legacy IPSEC client) and another 25 sessions for Anyconnect or Webvpn in this case are used in function.
To check how many sessions VPN is currently running, run the command 'Show vpn-sessiondb' and 'display the summary vpn-sessiondb '.
Find the official documentation for the ASA5505 on the following link:
Rate if helps.
-Randy-
-
How to limit maximum SSL VPN sessions by group policy on ASA5510?
How to limit maximum SSL VPN sessions by group policy on ASA5510?
There are ideas?
There are 2-Group Policy: within a maximum of 10 connections, in the second - 15 (total licenses for SSL VPN 25 connections).
Hi Anton,.
It is an interesting question.
Please check the following options, depending on your scenario:
simultaneous VPN connections
Pour configurer configure the number of simultaneous connections allowed for a user, use the command simultaneous vpn connections in the configuration of group policy or username configuration mode. To remove the attribute from the running configuration, don't use No form of this command. This option allows inheritance of a value from another group policy. Enter 0 to disable the connection and prevent the access of the user.
simultaneous vpn connections {integer}
No vpn - connections
http://www.Cisco.com/en/us/docs/security/ASA/asa84/command/reference/uz.html#wp1664777
There is a global command, although may not be useful, I wanted to share it with you:
VPN-sessiondb max-session-limit
--> To specify the maximum limit of VPN session.
Best option:
What you can do is to create a pool of IP 10 IP addresses in one and 15 in the other, this way you let only 10 connections and 15 respectively.
IP local pool only_10 192.168.1.1 - 192.168.1.10
IP local pool only_15 192.168.2.1 - 192.168.1.15
Then,
attributes of the strategy of group only_10
the address value only_10 pools
!
attributes of the strategy of group only_20
the address value only_20 pools
-
How SSL VPN packages for two ASAs clustered licenses
Hi all!
If I have installed two Cisco ASA 5550 (ASA5550-BUN-K9) in failover mode, which I know support only 2 concurrent sessions of SSL VPN and you want to upgrade my boxes to support 15 AnyConnect SSL VPN sessions, how many licenses packages I need to buy?
An ASA5500-SSL-25 for both boxes or two ASA5500-SSL-25 for one per box?
Depends on what version of ASA you are running.
If you are running version 8.3 and above, then you just buy 1 ASA5500-SSL-25 for a failover pair and it would work. If you buy 2 ASA5500-SSL-25, one license per box in failover pair, then the license gets grouped into 50 SSL user license.
Here is the license information for ASA version 8.3 for failover pair:
For ASA running version 8.2 and below, you are required to buy 2 ASA5500-SSL-25 (one of each ASA in the failover pair) as the license should be exactly the same for the pair to failover to work, in the earlier version of the SAA.
Hope that makes sense.
-
Cisco ASA VPN session reflect a public IP of different source
Hi all
I tested and managed to successfully establish the vpn on my cisco asa 5520.
On my syslog, I can see "parent anyconnect session has begun" during my setting up vpn and "webvpn session is over" at the end of my vpn session
where public ip used to establish the vpn address is reflected. However after the line "webvpn session is over", I can see other lines in my syslog example "group = vpngroup, username = test, ip = x.x.x.x, disconnected session, session type: anyconnect parent, duration 0 h: 00m23s, xmt bytes: 0, rcv:0 bytes, reason: requested user" where x.x.x.x is not the ip address used to establish my vpn for remote access, it is not related to my vpn ip address below. I am very sure that the x.x.x.x ip failed any vpn for my cisco asa5520. So why it is reflected in my logs to asa cisco? Pls advise, TIA!
Hello
Think I remember some display on a similar question in the past. Did some research on google and the next BugID was mentioned in the discussion.
113019 syslog reports an invalid address when the VPN client disconnects. -
How to allow remote VPN Sessions to communicate
Hi all
I'm trying to understand how to enable remote VPN client sessions to communicate. For example, if my manager has been connected via VPN to the office and needed me to fix something on his laptop, I cannot VPN to the office and RDP into her laptop. Not sure if this can be done without pain.
A brief out of my config. Remote client VPN sessions work fine. It's only when I try to access other customer VPN sessions, is where I have a problem.
Thank you is advanced!
FW # executed sho
: Saved
:
interface Ethernet0/0
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 4.4.1.8 255.255.255.252
!
interface Ethernet0/2
!
interface Ethernet0/3
!
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
outside_in list extended access permit icmp any one
split_tunnel list standard access allowed 192.168.1.0 255.255.255.0
inside_access_in of access allowed any ip an extended list
outside_access_in of access allowed any ip an extended list
access-list sheep extended 10.10.10.0 any allowed ip 255.255.255.0
IP local pool vpn 10.10.10.1 - 10.10.10.15 mask 255.255.255.0
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 0.0.0.0 0.0.0.0
inside_access_in access to the interface inside group
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 4.4.1.7 1
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto-map dynamic inetdyn_map 20 the value transform-set ESP-DES-SHA
map inet_map 65535-isakmp ipsec crypto dynamic inetdyn_map
inet_map interface card crypto outside
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
crypto isakmp identity address
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 21
internal vpnipsec group policy
attributes of the strategy of group vpnipsec
value of 192.168.1.5 WINS server
value of server DNS 192.168.1.5
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list split_tunnel
moobie.com value by default-field
type tunnel-group vpnipsec remote access
tunnel-group vpnipsec General-attributes
vpn address pool
Group Policy - by default-vpnipsec
vpnipsec group of tunnel ipsec-attributes
pre-shared key nope
!
Hello
You need to allow pool vpn split tunnel, here's what you need to do
split_tunnel list standard access allowed 10.10.10.0 255.255.255.0
same-security- allowed traffic intra-interface
Kind regards
Bad Boy
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
-
Road of default remote access VPN session
ASA version 8.2.2
How do you assign remote access VPN sessions a single default route? Other than the default route assigned to ASA. For example, my VPN ASA (handles vpn sessions), defaults to the Internet. I wish that sessions VPN for remote access by default internal network first, then follow the default route to the Internet on another firewall.
The SAA outside the IP address of the interface is a public. Inside is a private 10.x.x.x. VPN clients receive 172.17.x.x.
Thank you
After the command 'road' added keyword "tunnel".
in the tunnel
Specifies the route as the default gateway of tunnel for the VPN traffic.
http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/QR.html#wp1767323
-
Multiple VPN groups on the ASA firewall
I have a remote VPN configured in my ASA firewall with a group of users configured on the external ACS VPN. The group called VPNASA to authenticate via the ACS server and the server ip pool is on the firewall of the SAA. Now, my boss asked me to set up a second VPN group called VPNSALES on the ACS server for the same remote VPN on the ASA firewall. How to configure the firewall for the ASA to accept both the Group and authenticate on the same ACS server? I've never done this before so I need help.
Thank you very much!
Hello
all you need to do is create another group strategy and attach it to a group of tunnel: -.
internal vpnsales group policy
attributes of the strategy of group vpnsales
banner - VPN access for the sales team
value x.x.x.x DNS server
split tunnel political tunnelspecified
Split-tunnel-network-list split-sales value
address-pools sales-pool
value by default-domain mydomain.com
type tunnel-group vpnsales remote access
tunnel-group vpnsales General-attributes
authentication-server-group vpnsales
Group Policy - by default-vpnsales
vpnsales ipsec tunnel - group capital
pre-share-key @.
you will also create a map of the attribute named vpnsales for acs auth.
Thank you
Manish
-
How much memory can I mount in a Tecra M10 - 1CN?
How much memory can I mount in a Tecra M10 - 1CN and should be in two 200 pin SO DIMM DDR2 PC2-6400 800 MHz modules
Hello
Expand the memory depends on the chipset of the motherboard
The Tecra M10 supports the chipset Mobile Intel GM45 Express and this chipset DDR2 800 MHz RAM 8 GB maxSo first of all, that you can use 2 x 4 GB RAM modules, and on the other hand the speed of memory is limited to 800 MHZ.
Even if you use faster modules i.e. 1033 Mhz FSB would clock speed to 800 Mhz so it s not worth to use faster than the DDR2 800 Mhz modules
-
Satellite 2800-600: how much RAM can I install?
How much memory (RAM vivid), I can install on this computer. I want to have 512 MB but my systm stops when I install this memory size.
Sorry for my English
Poland Rafal
Hello
I found some information on this laptop and it seems that this laptop support max 256 MB (2 x 128 MB) of memory.
You can use the modules:
PS3004U - 1 M 06 64 MB
PS3005U - 1 M 12 128 MB -
How much memory a W500 can be seen on Vista 32
I know how 32 - bit operating system has a limit of 4 GB, but on my W500 system sees only 2.46 4 GB.
My Toshiba laptop Brothers sees 3 gb 3 GB installed.
Oh, when I say see I mean usage, it's how much can be seen in the applet to task manager or information system.
Now, I should more usable memory 2 gb + 1 gb? It seems that Yes
OR
I should more installation of sticks from the same manufacturer? My second stich 2 GB original lenovo W500 to remember but is a manufacturer of difrent than that has been installed
32 bit can only recognize max 3 gig and not 4 GB. Also with the ATI graphics card, it automatically allocates approximately 400 to 500 MB of the gig 3 recognized ram for hypermemory thingy, which means that you get essentially around 2.5 GB for the rest of the software.
-
HP Pavilion Notebook Gaming: How much ram can my cell contain?
Hello, how much ram can my cell contain?
the vehicle currently has 8 gb accompanying
Here are the specs
using the piriform Speccy
I see 2 housing and only 1 is used, but I'm not sure if the app is accurate
Product P0S78EA #ABU number
can someone let me know thanks
HelloHello
Manual: http://h10032.www1.hp.com/ctg/Manual/c04823146
Up to 16 GB max.
Concerning
Visruth
-
How much RAM Win 7 32 bits can recognize?
I installed on the motherboard of strips of 8 GB memory. Currently, my WinVista and WinXP can't see 3.5 GB max. sucks...
I intend to install Win 7 Home Premium edition. The amount of RAM it can recognize the same cluster?
Please advice. Thank you.
Edy
As 32-bit Windows may be able to address up to 4 GB, an individualized process can use up to 2 GB of space, regardless of how much remains free for use. Using the switch/3 GB can increase the amount of RAM available to applications, but does not increase the size of the system address space and will not increase the maximum amount of RAM used by the system.
Hope that helped.
Maybe you are looking for
-
Battery must be removed or not?
I just bought a new HP 8570W laptop and I need to know how to handle the battery. My laptop is the msot of the time connected to the a/c adapter, the question is: should I remove the battery and connect only when you plan a trip? Generally speaking,
-
The message "Power Save" tells me something very serious...
I get the following message if poster before my computer shuts... Automatic incoming energy saving (analog input)... What that does say? I have a 6 years, Vista Home Premium... Word 2003 with all the updates, I can access it; I use Norton Security. I
-
Choice of a model of desktop Inspiron for two monitors
I didn't keep on computer hardware for some time and I found myself completely confused now that I'm looking to choose a new system that will support two monitors. It seemed simple at first, but now I'm a little worried that I'm missing something. In
-
P2714T small screen to 1080 cannot calibrate
Setting the resolution to 1920 x 1080 on my newly arrived P2714T only fills the screen about the size of a 24 "display. Calibration works in this setting, BUT 24 "is not acceptable. Change the resolution of 1600 x 900 t fill the screen 27 ", but it f
-
Illustrator crashes on save in. AI with a layer of text not indicated
Illustrator 2015.3.1 - 10 of Windows with the latest updates installed and NVIDEA GTX GPU 970 (372.70) latest drivers running.Illustrator was working fine a couple of days. Today, when I was working on a new file and went to save, Illustrator crashed