How to activate the two IPS on VCS starter pack express

I have the Starter of Cisco Express works with a single IP address using a NAT. This only works inside the LAN. To enable this machine on the internet, I bought the key option to double network interface. I enabled both interfaces, but I don't know how I should configure the two IPS by access from the internet. I tried to activate the static NAT, but it did not work.

There is only a single default gateway and this is where most of the traffic will be released and which should point to the internet router.

If you have addresses of internall more than 'LAN', you can simply add additional routes via the administration console.

As if LAN is connected to LAN2 192.168.150.0/24 and you 192.168.175.0/24 your home and where your laptops

router for tha is 192.168.150.1 you would add that, on the road to xcommand, add the command:

xcommand RouteAdd


*h 'xCommand RouteAdd'


"Adds and configures a new IP route (also known as a static route)."


Address(r): "Specifies an IP address used in conjunction with the prefix length to determine the network to which this route applies."


PrefixLength(r): <1..128> "Specifies the number of bits of the IP address which must match when determining the network to which this route applies. Default: 32"


Gateway(r): "Specifies the IP address of the gateway for this route."


Interface: "Specifies the LAN interface to use for this route. Auto: the VCS will select the most appropriate interface to use. Default: Auto"

for the example given, it would be (user admin via ssh):

xcommand road add an address: 192.168.175.0 LG: gateway interface 24 192.168.150.1: LAN2

But to be honest I'm not sure jabbervideo it works well with the highway espress in

a lan environment double anyway.

As with a vcs - c / e deployment you have the model of the internal and external with vcs

different hosts where he tries to get funding and then depending on who gets the data

for the record. It may be that in any case only get you external IP of the vcs-e.

I would therefore simply deploy a DMZ where the outside and inside can reach the starterpack with

the same address or even external ip using a NAT that is hosted in LAN1 put directly on a public ip address in a dmz...

Tags: Cisco Support

Similar Questions

  • VCS Starter Pack Express 7.0.1 without DOUBLE NIC / Network configuration

    Hello community,

    can you please explain to me how to put a VCSESTRTPACK to the Internet? Just put the public IP address to the configuration of the Interface? I have just one public IP address, so I NAT? Or is it possible to make it work. I want to register outside, devices on Internet. Some evaluation criteria are behind NAT.

    What the routing configuration and deployment of the network?

    I'll put the VCSESTARTPACK for the server to register of external endpoints on the internet.

    And for internal services use an MCU and the TMS. So I nedd to internal and external communication to my VCSESTARTPACK. Is it possible to connect a VCSC internal in order to increase enrollment?

    Thank you

    Duplicate messages.

    Go here: https://supportforums.cisco.com/discussion/12263321/vcs-starter-pack-exp...

  • UPDATE to VCSE VCS Starter Pack Express

    Hello community support.

    just a quick question for the upgrade process. With this key:

     Video Communication Server Starter Pack Upgrade to VCS Expressway - TMS, Cisco Jabber Video for TelePresence 100 users CTI-VCSE-SPUPG-K9 TTC2-04

    I can add as an option on my VCSESTRTPACK and remove the pack before starter option. After that, I have a VCSE without refueling.

    But what of the Jabber user? How did the license provided for me?

    Can I install just the touch option even on MSDS and this will add 100 user of Jabber for her? Or do I have to buy a separate license for this?

    Thank you for the support :)

    From what I found online:

    • You can convert the Starter Pack, either a control or highway depending on what part number you use (CTI-VCSC-SPUPG-K9 or CTI-VCSE-SPUPG-K9).
    • You will lose the integrated supply management and Jabber video/Movi licenses.
    • You will retain licensing additional call that have been purchased on top of the base call licenses.
    • You will receive basic application of TMS + 100 licenses video/Movi Jabber.

  • Terca M4: How to activate the external ports, DVI and analog?

    Please can someone please tell how to activate the two external ports. I would use two DVI and analog to the office. Currently if you activate a second screen machine sets up the flat screen and the other the DVI external display. Is this in any way about this?

    See you soon

    Hi Matthew

    As far as I know you can connect an external monitor or a TFT. For this you can use the VGA (15-pin) port or DVI - D video, supported by PortReplicator III (PA3314E).

    Sorry, but I don't understand why you need the two holes at the same time. How many external screens that you want to use? Sorry if I'm missing something but perhaps you can explain your wishes more precisely.

    Good bye

  • Satellite Pro A100 - how to activate the shortcut keyboard-support on Vista?

    Hello. I've recently updated my satellite pro a100-828 to windows vista, and things work well to a large extent with two exceptions:

    1. I can't figure out how to activate the shortcut keyboard-support: media-keys to the left and the fn keys do nothing. There seems to be no shortcut keyboard-utility for windows vista in the drivers * tion. So what to do?
    2. the standby electricity utility is not available, which is good because of the power saver new vista. Except that I can't dim the screen, so the battery does not last me too long. How can I do this?

    Thanks in advance
    Best regards
    Christian

    Hello

    These problems can be solved in a few minutes. You only need the added package Toshiba. It contains the driver for the FN - key, Toshiba Power Saver and more useful tips.

    Here you can download:
    http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

    Good luck! :)

  • How to activate the spell checker

    I use Mozilla Thunderbirds e-mail and would like to know how to activate the spell checker - Help

    http://email.about.com/od/mozillathunderbirdtips/Qt/et_inline_spell.htm

  • How to activate the pop-up windows?

    I can't fill a demand for services with ASCAP because I've not enabled popups. So, how to activate the pop-up windows?

    You can uncheck the block pop-up windows under the Orange Firefox button > Options > Options > content tab.

    See more details here

  • How to activate the BT on the Satellite C660-184?

    Toshiba produces online information continues to tell me that the Bluetooth 3.0 is available for my computer, but annoyingly not to tell me how I can get it.

    It would be useful that this information came with a link that I can use to act on the information.

    Does anyone know how bluetooth can be enabled on my computer?

    All the info and the latest BT downloads, you can find the portal of Toshiba BT - http://aps2.toshiba-tro.de/bluetooth/

    How to activate the BT?
    Activate WLAN first and when WLAN led on the key FN + F8 use combination and allow to BT

  • r204tx: how to activate the deletion warning on hp computer laptop r204tx

    Hi all!

    Recently I bought hp laptop r204tx with Win. 8.1 - 64 bit, however, whenever I want to delete any file, folder, etc. I press the button Delete and deletes directly without any warning or alert!

    Please, help me to solve this problem and enable the alert message for the delete option...

    Thanks in advance!

    How to activate the Confirmation alert delete:

    http://www.askvg.com/how-to-enable-delete-confirmation-dialog-box-in-Windows-8/

  • Satellite Pro U200 - how to activate the bluetooth connection

    How to activate the bluetooth connection?

    Hello

    First check to see if your computer supports BT
    If the laptop supports BT, then you should find a BT tag at the bottom of the unit.
    If there is no label then your machine was not equipped with internal BT module!

    If the laptop supports BT, then use the FN + F8 key to go to the BT
    Then BT should start installation and configuration.

    For more details, see this forum and this Toshiba BT Portal:
    http://APS2.toshiba-tro.de/Bluetooth/?page=FAQ

  • How to activate the LCD in Satellite C850-B374 sensor after the BIOS update?

    Hi, friends

    I m currently a customer satisfied with Toshiba since April 2013. I've been using laptops since 2007 after using different brands, I found Toshiba to be good.

    I recently updated the Bios from 6.0 to 6.50 of the Toshiba service station.
    Update was successful and the computer works fine.

    But after restarting the LCD sensor that activates the power button in this model of laptop does not work. After entering the utility parameter that I came to know that CE of bios version is 6 and bios version 6.50 so how to activate the sensor lcd start automatically while I open the lcd screen

    Ashik

    > How to activate the sensor lcd start automatically while I open the lcd screen

    You want to start Notepad by opening the cover. Right?
    In this case you should enable the option in the system of Windows 8 settings

    [Why my laptop Windows 8 start automatically when you open the cover of the display? | http://APS2.Toshiba-tro.de/KB0/FAQ2C03FA0001R01.htm]

    "You need to find the option called: + open Panel - Power On" feature.
    This option must be enabled in order to automatically start the computer when the display lid is opened

  • How to activate the resolutions of wide screen on Satellite Pro A10

    Hello

    I looked through various positions through the forums, but have not found how to activate the wide screen on a Toshiba Satellite Pro A10 resolutions.
    The 2 following wires offer partial answers:

    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=19570
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=19677

    The solution in the 2nd post won't work because the A10 has an Intel graphics card, not a Nvidia. He suggested also, modify the INF of the graphics driver, but to extract the driver (SA10B2DP.exe) file includes an installer, but no INF.

    Just look to see if anyone has any advice on how to activate the resolutions such as 1440 x 900 or 1680 x 1050.

    Thank you

    Hello

    you mean on the external screen, Don t you? If you have an intel chipset graphic why Don t you download the drivers from the website of intel.
    Maybe it offers a resolution of the external display.

    I don't know if the res external can be set to widescreen on this chipset as the drivers are somewhat limited...
    Can you describe what monitor you have and how you connect it to your machine. (d-sub or DVI)?

    Would appreciate some reactions :)

    Welcome them

  • How to activate the face recognition login

    Hello

    Can someone tell me how to activate the face recognition login my computer instead of the normal password

    Hello

    You can run these steps:

    1. register new account
    2. Enter the parameters click the logon tab
    3. turn on last automatic selection of titles
    4. you can also choose the first option in authentication mode
    5 restart your laptop
    6. in the laptop restarts, click on change user
    7. Select start Face recognition

    All that s!

    It's working now?

  • How to activate the S-video port on a satellite M30X 154?

    Hey does anyone know how to activate the S-video port on your laptop by Satellite SM30X-154?

    If I press the FN + 5 keys the only options I get is LCD and no S-VHS option. My TV is set up for this I have Watch DVD through the cable.

    When I connect the cable to the laptop, nothing happens!
    Help

    Hello

    Sorry, my A100 Tosh has a Geforce 7600, I don't know what is your GA.

    But on mine, I have a NVidia Control Panel, where I can configure dualview,
    normally, which allows me to choose between the builtin LCD and the external monitor (VGA Port).

    When a TV is plugged and not recognized, I can apply recognition there.
    Relative to the opening of the Panel, the TV is also available.

    Maybe I could help you.
    If this isn't the case, note that the settings of windows your TV is not available.
    Try to go to the User Interface of your graphics card...

    Matz

  • Satellite M35X-S163 - how to activate the touchpad scrolling feature?

    How to activate the functionality of scrolling on the touchpad of my laptop Satellite M35X-S163?

    Hello

    The touchpad scrolling feature can be enabled in Control Panel > mouse.

    You'll find the option but don t forget that the driver for the touchpad should be installed and you can find it on the Toshiba site:
    http://www.CSD.Toshiba.com

Maybe you are looking for

  • A site "radiobar" took over my home page. How can I get rid of him?

    A site "radiobar" took over my home page. How can I get rid of him? URL of affected sites http://

  • Satellite A80: Update DirectX 9 .0c to play Call of Duty 2

    Hello It's Carlos. I have a portable Satellite A80, and I want to update the display driver to be able to play Call of Duty 2, in need of a Directx 9 .0c compatibility. Yet since 2005 it has some new drivers from Toshiba Web site. The last driver I h

  • ZBook15: docking station

    Dear Sir/Madam, I used to have a Compac HP 8510w. I got with a docking station that is their standard REPLACEMENT-IX01. My question is if I can join my new zbook15 this docking station or not. Kind regards Dave

  • Removing static route get % corresponding to any error no route to remove

    I'm trying to remove a static route, I added: ------------------------------------------------------------------------------------------------- R2 #show ip routeCode: C - connected, S - static, mobile R - RIP, M-, B - BGPD - EIGRP, OSPF, IA - externa

  • BlackBerry 9105 Wi - fi Smartphones

    I have connected my Pearl to my home network via wi - fi, and I can access the internet - but only when I lit data. By the time I turn off data I have no web connection, even though I am always connected via WiFi to my home network. I have reason to