How to add the second network card?

Similar Questions

• Add the second NETWORK card to vSwitch

  I'm working on trying to add to install a second NIC physical to the vswitch which is installed by default when ESXi. I use the code below, but when I run it, it disconnects in fact the main physical network card and of course, I then lose connection. I tried different varients of this and even finished by adding a port of vmk, which I didn't do. I just want to add the second network card as a standby card network.

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1
  

  The cmdlet Set-VirtualSwitch accepts a string array as the value of the parameter - Nic. So you should be able to:

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1,vmnic2
  

  Best regards, Robert

• Call "HostNetworkSystem.UpdateVirtualSwitch" for the error of the object when you attempt to add the second NETWORK card

  Hi there - first post here, so please be nice :-).

  We are just trying to place an ESX4.1 own deployment in our environment (no previous installation of VMWare) to our main office, using Dell M610 and blades blades M600 to what would become our DR - two sites site hosting VMS on Equallogic iSCSI SAN disks.

  I configured 4 of our blade M610 with ESX 4.1 successfully and they work very well.  These blades have double NIC onboard, and after the initial installation of ESX, I could go to the virtual switch and add in the second NIC like vmnic1 (because one had already been detected during installation).  This fine workd for 4 guests on the M610 blades.  However, I came today to make my first installation on one of the old M600 blades and I encountered a problem.

  Installation went without any problems and I was able to add the host in my vCenter.  I can change all the settings without problem (created the Port of VMKernal for my connection to SAN iSCSI etc, but as soon as I try to add in the second NETWORK card, he paused for a while, and then I get the following error message:)

  Call 'HostNetworkSystem.UpdateVirtualSwitch' of object 'networkSystem-56 "on vCenter Server"VCEN01." ournetwork.local"failed. (network name has been changed for post).  When this happens, it locks up again for several seconds, and when the system returns, I can no longer communicate with the ESX host (Observer of events in vCenter watch 'host is not responding' and I find that I can not ping the host unless I reboot it.)

  If anyone has any suggestions I would appreciate it that I don't want to proceed down to the line with our Installer if theres an underlying issue and I need to redo everything.

  Concerning

  EFIN.

  Do you get the same error when you try to add the network adapter by using the command line?

  1. esxcfg-vSwitch - L vmnic1 vSwitch0

  If you have found this or other useful information, please consider awarding points to 'Correct' or 'useful '.

• How to use the second network card physical to Virtual Machine?

  Two queries. We strive to VMware Server 2

  How to increase the speed of the network of the guest operating system.  Currently it shows 10 Mbps.

  If we have a second physical network adapter, is it possible to use it for the guest OS. ?

  We are noobs, please give links to this info or explain in steps.

  concerning

  Merlina.

  Welcome to the VMware forums communities.  You may be able to fix your problem by changing the type of virtual NETWORK adapter and install VMware Tools.  See this KB article - http://kb.vmware.com/kb/1002456.

  Dave

  VMware communities user moderator

  Now available - vSphere Quick Start Guide

  You have a system or a PCI with VMDirectPath?  Submit your specifications to Officieux VMDirectPath HCL.

• How to add a second network card to my VMs

  I would like for my VMs see as two NICs installed on my machine. What are the steps to get there there are only three options briged, host-only, and Nat which should I use?

  Probably want to make a host only NIC then and have a second VM on the host that too, assuming that the one you already have is filled, that simulates a machine on the inside of your network.

• CMS OVA, adding the second NETWORK card breaks the first NETWORK card

  I'm testing CMS 2.0 and when I try to add a second NETWORK card in VMware, he immediately interrupts the first network card.  As soon as the loading of the image, the first NIC fails.  Even if I disable iface b, it will allow all traffic where iface one.  If I stop the application, remove the NETWORK adapter and run it back again, it works very well to the iface one.

  I want to test the public face with box feature, but I can't if I can't add a second network card.

  How do you add the second network interface and interface you add?

  You should add 'VMXNET3' type if you use VMWare, if you chose something else, you invalidate your license, see section 3.3 of the virtualized CMS 2.0 Setup Guide for deployments.

  If you need assistance, you must move this thread to the section of telepresence of forums, where this device is actively discussed.  You can change your question and change the categories at the bottom of the page.

• Cannot add the secondary network card

  Hello! I bought specially for ESXi (Intel PRO/1000 MT Desktop Adapter, model number 8390MT) a new PCI Intel network card. It is listed as a supported network component. I have pluged it started, the host, went the networking, but I still see only one, the old network card. It would appear there automatically or must something needs to be done in the linux command line? I'm not good with linux, maybe I should just re - install the ESXi?

  Make sure that you add the NIC in the vSwitch. If you just go to the page of networking in the VShpere customer, you won't see the second NIC automatically connected to the vSwitch. Did you do that?

• Is it possible to add the second graphics card for this model Y510p?

  I've been doing mixed responses from customer service chat lenovo so I'm posting my question here. Recently, I bought this laptop. It comes with a single graphics card. I heard this model has ultrabay and you add another graphics card. My question is - is it true that you can add a second graphics card in this system by using ultrabay? Please let me know. I'm confused if SLI and ultrabay means the same thing. If this is the case, then this system is not sli. I appreciate your help.

  http://shop.Lenovo.com/us/en/laptops/LENOVO/y-series/y510p/?SB=:000001 C 9: 00011E0A:

  Also, don't forget to find the extra $20 or sometimes $50 discount code for the Lenovo y510p and apply it to the Fund. The time I bought my laptop I used the code USPY5168320, you will find a similar code if this does not work.

• How to upgrade the wireless network card in Windows Vista

  Hello

  Please how can I update the wireless network card?

  Thanks for the help

  Hello

  I suggest you try the steps from the following link to update the wireless network card drivers.

  a. right click on the Start button and click on Device Manager.
  b. display all devices on one.
  c. right-click on the WLAN driver and click on Update.

  Display us the results, once you try the steps above.

• How to get the driver network card and on the use of the PowerCLI firmware version?

  Hi all

  I would like to know if anyone can help me in sharing the PowerCLI script to list the server NETWORK card driver and the firmware version?

  Note: I use the HP Blade Server and it's manual ESX - CLI command output:

  	HP BL 465c G8
  	~ # ethtool-i vmnic0
  	pilot: be2net
  	version: 10.5.65.4
  	firmware version: 10.2.340.19
  	bus-info: 0000:04:00.0

  	HP BL 465c G7
  	~ # ethtool-i vmnic0
  	pilot: be2net
  	version: 10.2.293.0
  	firmware version: 4.9.416.7
  	bus-info: 0000:04:00.0

  Any kind of help would be greatly appreciated.

  Thank you.

  PowerCLI Version

  ----------------

  VMware vSphere PowerCLI 6.0 Release 2 build 3056836

  ---------------

  Component versions

  ---------------

  VMWare AutoDeploy PowerCLI component 6.0 build 2358282

  VMWare ImageBuilder PowerCLI component 6.0 build 2358282

  VMware vSphere PowerCLI component 6.0 build 3052101

  It works for you?

  $esxName = "MyEsx".

  $esxcli = get-EsxCli - VMHost $esxName

  $esxcli.network.nic.list () | %{

  $esxcli.network.nic.get ($_.) Name) |

  Select Name,

  @{N = "Driver"; E={$_. DriverInfo.Driver}},

  @{N = 'Version'; E={$_. DriverInfo.Version}},

  @{N = 'Firmware Version'; E={$_. DriverInfo.FirmwareVersion}}

  }

• IMAQdx mind traffic on the second NETWORK card

  Hello!

  My system:

  -Labview 2011 SP1 with NO Vision and IMAQdx

  -Windows 7-32 bit

  -2 NICs (Intel Pro 1000)

  On a NIC (subnet: 192.168.0.x - Intel pro driver) a sick Ranger is connected. Store it works with Studio of sick Ranger or the Labview Toolkit Ranger.

  On the second NIC (subnet: 192.168.1.x - Realtek dreiver) a Vision of Basler GigE camera is connected. It works with the grun80 pylon Viewer and IMAQdx GigE functions in Labview.

  If I start the acquisition of two cameras using the Studio store and Basler pylon Viewer (no Labview) both cameras acquire images at high speed without any interference.

  If I use Studio Ranger or LV-store Toolkit for the Acquisition of store it works selection UNTIL I have start a Labview VI containing the screw IMAQdx to acquire images of the Basler camera. As soon as the VI performs stops Acquisition of Ranger and Ranger loses the connection.

  I guess the driver IMAQdx is somehow interfering with two network cards.

  Suggestions how to exclude one of the NICs of IMAQdx driver or can someone tell me what is happening on the network driver layer when loading of IMAQdx?

  The purpose of my request to LV, is that both cameras can be used at the same time!

  Thank you!

  Disable the identification of cams network solve the problem?  See also How to disable IMAQdx sending periodically a Ping 'discovery'.

• How to add the WRT54GL network as AP

  I have an existing router with network, all computers have manually assigned IPs. Now, I want to add WRT54GL to serve visitors with the radio. For them to WRT54GL DHCP assign IPs in the range no other computer in LAN uses. I want that they have access to the internet and to the rest of the LAN.

  If I connect WRT54GL by WAN port they only access to internet, but can not see LAN.

  But if I connect via LAN, I can access LAN, but not the internet. It works, if I put the IP of the router (on WRT54GL on 192.168.100.1 but now he is in conflict with the main grave failure of router and network). I do not understand why wireless computers get WRT54GL IP as the gateway and not 192.168.100.1 as it is defined in the basic configuration.

  I guess I should do something in advanced routing, but which?

  You can try tomato or DD-WRT. Tomato, it's a little less 'crowded' that DD - WRT, but you can add options specific to the configuration of DNSMASQ (the DHCP server that works under Linux) that will specify a default gateway.

  If you decide to go to the tomato (which I am more familiar with more of dd - wrt), DNCP/DNS has a box in which you can set options of configuration of DNSMASQ. There is also a link on this page for a site that has great descriptions of DNSMASQ. This site ar options below:

  to set the default 192.168.4.4 route option, do -dhcp-option = 3, 192.168.4.4 or -dhcp-option = option: router, 192.168.4.4

• Impossible to use the second NETWORK card on VM

  I'm under VMware Workstation9 and I'll put up a configuration 5.1 ESXi

  VM1 - Windows 2008 - acting as a DC and a NFS storage
  VM2 - ESXi 5.1

  I added a second NIC on VM1 and VM2 to IP storage but I can't PING vice versa

  IP address:
  VM1 - 198.168.150.10 SM: 255.255.255.0
  VM2 - 192.168.150.11 SM: 255.255.255.0

  VMnet2 is used for the management, no problem with this vmnet3 is used for storage traffic but no communication possible

  Any Suggestion?

  Check the response of jmattson to Re: operating system of the virtual machine attempted to activate the adapter Ethernet0 promiscuous mode. This is not allowed for security reasons. solves the problem.

  André

• How update you the wireless network card

  My WLAN continues to stop. What should I do

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  For more information:

  It comes with Vista, upgrade install and activate Forum.

  http://social.answers.Microsoft.com/forums/en-us/vistahardware/threads

  They will help you with your question in Vista Hardware and drivers Forum above.

  See you soon.

  Mick Murphy - Microsoft partner

• Adding a second NETWORK card on the server HP Proliant ML 350 G5

  I have a new HP Proliant with a guest of Windows 2008.  HP came with two network cards on the MB.  I need double-home this box on both networks, at least for a while, and this server will be the only road between subnets.  It's just a stand-alone installation inset.

  I looked in the settings of the BIOS on the HP and it's a little confusing, but I'm sure that the second network card is active (it lights up when it is plugged).  When I try to add a NETWORK adapter to the configuration of the host, it is as if the second NETWORK card is not present.

  My question is what is the best way to add this second NETWORK adapter and how do I do that?

  I'll need access to the host of the VI Client on both networks - at least for a while.

  Any help would be greatly appreciated.

  If you go to configuration-card network in the vSphere client is the 2nd NETWORK card that there are listed?  If ESXi is able to recognize the NETWORK adapter (or other people that you add) they should appear in this list without any config changes and be ready for use.

  What kind of networks are you fill?   If one is considered not secure you could be better not add a management on this network port and prefer to have access via a VPN VM or a secure hosted VM / dual.

  Dave

  VMware communities user moderator

  Now available - vSphere Quick Start Guide

  You have a system or a PCI with VMDirectPath?  Submit your specifications to Officieux VMDirectPath HCL.