Similar Questions

• How to configure the different VLANs (using the E3200)?

  Hello.

  I want to implement different VLANs (using the E3200) so that I can have two different networks that cannot access each other.

  The E3200 is connected to a modem for internet access.

  I would like that the two networks to access the internet.

  The only E3200 does support the creation of VLANs?

  If not, is there another way I can satisfy the requirement by using the single E3200 (using something else than VLANs)?

  At the end of the day, I think that I would need at least another router.

  Thus, for example,.

  Router a (E3200) is connected to the configuration / modem to DHCP with a rank 192.168.1.1/24 LAN IP address.

  Router B is connected to the router and Setup for DHCP by using a LAN IP range 192.168.2.1/24.

  This peripheral way connected to the router A should not have access to devices connected to router B and vice versa, correct?  For example, X device connected to the router cannot ping or browse files on the device is connected to router B and vice versa, correct?

  Do I need to configure anything else on router B?  For example, do I need the DNS configuration settings so that devices connected to router B can connect to the internet without problem?  Do I need to specify that these VLANs are not bridged and which router, or both?

  I already know how to configure a static IP address, DHCP, beaches LAN IP and static DNS settings on a router, etc.

  With respect to wireless devices, I think that they would follow the same model; for devices connected to the router wireless (E3200) have access to other devices Wi-wired and connected to the router, but not to devices with or without wire, connected to router B and vice versa.  However, if the wireless devices have currently access to wired devices was also connected to the router, so it's good for now.

  Thank you very much!

  -Rami

  The E3200 has no support VLAN according to the manual. There is no way to configure two separate networks with this single router.

  You need to add network electronics.

  Ex:

  Managed with VLAN switch

  Another wireless router with VLAN

  If your modem provides several public or private IP addresses, then you could put a switch after the modem and two wireless routers that are attached to the switch.

• How to configure in the apex using other engine of transformation XSL - FO instead of Bi publisher

  can someone give me a quite complete example for me on the engine configuration of processing XSL - FO in the Apex.

  I'm feeling rather puzzled about the example set by the introduction of the link:http://www.oracle.com/technetwork/developer-tools/apex/application-express/configure-printing-093060.html#06

  in the apex_fop_render.jsp file.

  Hi 2952702,

  2952702 wrote:

  Please change your login username of "2952702" to something meaningful. Reference: Video tutorial how to change username available

  When I install the apex5 rest data service, the installation guide tell me pdf printing is supported by the rest data service

  but after the installation of ADR, I don't have the result I want.

  

  Yes, as you directed in the code snippet included listener Web Oracle APEX Documentation Options, Services (ORDS) data Oracle REMAINS usable as a PDF as FOP support print server is included in the ADR 2.0 and later (last ADR 3.0).

  Reference:

  • Marc Sewtz: PDF printing with Oracle Application Express 4.2.2
  • http://www.Oracle.com/technetwork/developer-tools/Apex/learnmore/custom-PDF-reports-1953918.PDF
  • Re: Printing with APEX 5.0 PDF

  NOTE: The links are for APEX 4.2, but they still apply for APEX 5.0, if you plan to use ADR 2.0 and later versions. These links show how to configure ADR as a print server and how to design and print reports.

  I hope this helps!

  Kind regards

  Kiran

• How to configure PXI-8464 to use the channel API

  I have a PXI-8464, but I don't know how to set up so that I can access block API of ways.

  Normally, I can choose the NPC channel by selecting "CAN0". For example, I can do it to the MAX:

  

  Then I can, just select "CAN0" in VI:

  

  However, on my remote system, it looks like this to the MAX:

  

  Notice how there is no "CAN1" or anything like that. Therefore, in the VI, it has a long list of channels CAN, but none of them can be used to connect to my channel PXI-8464.

  

  How do I get my CAN map to work? Thank you.

  Hi Bladhart,

  You have configured the NPC card via MAX for the RT system?

  Here is a link that might help!

  Configuration of a real-time Application of NI-CAN to the MAX

  http://digital.NI.com/public.nsf/allkb/D2D8B947369F453986256F89006F40B0

  Thank you!

• How to configure a user to use getManager() for sound manager in HumanTask

  Hello
  
  I have a simple AC.
  We create users and groups in weblogic and assign the task Participants using these users.
  
  I want to build a simple human task, which must obtain authorization from the Director.
  I don't want to assign the user statically, but I want funciton "user.getManager ()" allows you to assign a participant to the task on the 2nd level.
  To do this, the user must be mapped to a handler. But how can we do this?
  
  In weblogic-> security domains, I see only users and groups, but nowhere I see a Manager where I can assign orders to a Manager or a user to a card Manager.
  Can someone help me in this.
  
  Concerning
  RaviKiran

  Hi Ravi
  1. nothing beats a Manager configured separately in the weblogic console. Sound like that. Even the Manager is also one user that another user. The link looks like this. Each user will have standard properties such as firstName, lastName, Department, dateOfBirth, phone number, email etc etc. They also have an attribute as a Manager and the value of the present is just reference to another user. I hope you got the point.

  2. If, in the console Weblogic, say you create 2 users: weblogic1, weblogic2, weblogic3. And you can assign properties of base for each other like firstName, lastName, etc.. For weblogic1, assign the handler as weblogic2. To weblogic2 assign Manager as weblogic3 etc.

  3. now behind the screens in the Workflow, SOA, when you run user.getManager () and if the user is weblogic2, the value will be automatically weblogic2. And it lights up. You don't have to do any programming for it. The workflow will use the LDAP API to get the value for each standard property if they are named using standards such as firstName = givenName lastName = sn, emailId = mail etc etc. Here's all of the standard object properties for users, AD groups. Moreover, most of them apply to groups also in addition to users.

  Now, the real trick is, when you create new users in weblogic, you can specify firstname, lastname, mail etc. But to specify the Manager, for now, use this workaround given post below. Before submit you samples or explore SOA/BPM, create some accounts testuser in weblogic ldap integrated by default using app demo community seed (servlet). You can open this EAR and then the WAR and extract the .xml file and edit to add any substance you want.

  The link below should give you an idea more:
  Re: Kingdom is not met for the BPM app (See my answer)
  Re: Seeds Demo defective community

  Thank you
  Ravi Jegga

• How to configure proxy services to use the file transport?

  Hello
  
  I configured a proxy service to query for files in the specified folder. And it is configured to use the file transport.
  
  While running, I get the exception - follwing
  
  
  < 27 April 2012 4:08:28 PM GMT + 05:30 > < error > < WliSbTransports > < BEA-381602 > < error has occurred during the elections of the ProxyService service endpoint resource $ ServiceTypes_SB$ BinaryService: javax.naming.NameNotFoundException: while trying to search for "wlsb.internal.transport.task.queue.file" did not find subcontext "wlsb. Solved "; other name "wlsb/internal/transport/task/queue / '.
  javax.naming.NameNotFoundException: while trying to search for "wlsb.internal.transport.task.queue.file" did not find subcontext "wlsb. Solved "; other name "wlsb/internal/transport/task/queue / '.
  at weblogic.jndi.internal.BasicNamingNode.newNameNotFoundException(BasicNamingNode.java:1139)
  at weblogic.jndi.internal.BasicNamingNode.lookupHere(BasicNamingNode.java:247)
  at weblogic.jndi.internal.ServerNamingNode.lookupHere(ServerNamingNode.java:182)
  at weblogic.jndi.internal.BasicNamingNode.lookup(BasicNamingNode.java:206)
  at weblogic.jndi.internal.WLEventContextImpl.lookup(WLEventContextImpl.java:254)
  Truncated. check the log file full stacktrace
  
  Ask for help to solve this problem.
  
  Thanks in advance.
  
  Concerning
  Shyam.V

  Internal JMS queues depends on OSB are not there for some reason any.

  Are all correctly target JMS servers?

  How did you create the domain and all the managed servers are started?

• How to configure RV042 VPN to use Windows 7 client native IPSec?

  The question is in the title, I want to make the Windows client compatible with my RV042 VPN because Shrew Soft VPN fail to tunel after that little time and QuickVPN do not support Windows 7 or a 64-bit version of Windows.

  Windows does not have an IPSec client, what they offer is a VPN client that can connect to PPTP, L2TP/IPsec (on IPSec), IKEv2. To connect directly to the router RV that our only option is to connect over PPTP once the PPTP server protocol is enabled on the router. If you have a server located behind the router, you can configure to be an endpoint to one of the above types. Don't know why, Mac and Windows don't have a naked IPSec feature built-in clients.

  Some third-party applications to consider:

  Windows: ShrewSoft IPSec Client

  Mac OS X: IPSecuritas

  Both are relative simple to set up and on the routers RV0xx work fantastic and an exellent substitute QVPN. With these applications you set up the tunnel as a group and use the "XP/2000 Microsoft VPN Client ' option." " This option is a bit misleading because it seems to imply that the native VPN client can support IPSec settings, when it referred only that a computer would use this option during its WAN IP address is not always known.

  I hope this helps.

• How to configure Windows Vista PC using PLAP?

  We are interested in cofigure our equipment to use the VPN before you open a Windows session. No problem in XP, but we have activated something called PLAP to get appears the network connection icon in the bottom right. The problem is how we can activiate PLAP. It seems that it is a VISTA fetaure itself, but we are not in a position to know where it is, or how we do.

  Could you please kindly send us a few steps to solve this dubte?

  Thank you much in advance.

  GEMMA NAVAS

  JF HILLEBRAND SPAIN S.A.

  [email protected] / * /.

  This should help:

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect24/Administration/Guide/ac03features.html#wp1056587

• How to configure vswitch security policy using the API?

  Hello world

  Does anyone know how to set up a vswitch on ESXi Server security policy by using the management API (the idea is to do this in a script)?

  I think specifically the macchange and forgedxmit parameters which are set to true by default, and I want to change false.  Note that I also need a way to control the value from a script.

  I used to do with vmware-vim-cmd hostsvc/net/vswitch_setpolicy-securepolicy-macchange = false vSwitchn and vmware-vim-cmd hostsvc/net/vswitch_setpolicy-securepolicy-forgedxmit = false vSwitchn in the ESX 3.x service console, but I'll try (unsuccessfully so far) to find an equivalent using RCLI or Powershell (I don't want to enable ssh on my ESXi and use vim - cmd as I want to be able to do remote securely.

  Ideally, it would work while the host is in active locking mode (so I only need to authenticate on my server vCenter).

  Advice would be appreciated.

  See you soon,.

  Stéphane

  To update the security policy, you will need to watch the HostNetworkSecurityPolicy : http://www.vmware.com/support/developer/vc-sdk/visdk25pubs/ReferenceGuide/vim.host.NetworkPolicy.SecurityPolicy.html#allowPromiscuous

  You'll want to access the vSwitch you are interested using the following:

  [hostSystem->-> networkSystem configManager - >-> vSwitch networkConfig]

  Once the reference to the vSwitch, you'll want to create HostVirtualSwitchConfig spec: changes to http://www.vmware.com/support/developer/vc-sdk/visdk25pubs/ReferenceGuide/vim.host.VirtualSwitch.Config.html or policies make-> security which will contain (allowPromiscuous, forgedTransmits, macChanges) for changes that are just Boolean parameters.

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  http://Twitter.com/lamw

  If you find this information useful, please give points to "correct" or "useful".

• How to configure Firefox 6 to use a proxy to access the internet?

  Is there something similar in the menu options / advanced which was available in previous versions of Firefox?

  Click the Firefox button > Options > advanced > network > settings. Select "Manual Proxy Configuration" see screenshot.

• How to configure 2090 BNC for use on LabVIEW?

  Hi all

  I'm new on products OR, and I tried to use the BNC connected to a PCI card 2090 6036E on LabVIEW data acquisition. However, I still can't find a way to add this device (2090) to my list of 'Devices and Interfaces' OR max. As far as I understand, this step is necessary to assign the pins and begin to acquire data from the BNC-2090 on LabVIEW channels.

  Any thoughts? I would appreciate any help on this matter.

  The 2090 is just a silent block of endings. It does not show as a device. You acquire DAQ device - the 6036.

• How to configure dreamweaver do not use CSS?

  I know it's frowned upon to not use CSS, but, the reason why I want to do everything in HTML is because I want a list of my page on ebay, ebay does not support the use of css and it seems at least that way, everything must be done only in HTML, is there a way to set dreamweaver so that it does not automatically make my formatting are turning to the CSS?
  
  Thank you
  Bill.

  .oO (BKolos)

  > I know it's frowned upon to not use CSS, but, the reason why I want everyone
  > done in HTML is because I want my page on the auction and the sale at auction of the list
  > does not support the use of css, everything must be done only in HTML

  If it's on eBay or on a similar platform, then in fact you can use CSS.
  Simply add an element 'style' to the body (!) page to link to a
  external style sheet. It's completely invalid HTML, because the 'style '.
  element belongs to the head of the document, but it should work almost
  all browsers. And since usually the rest of the page of the auction is not valid
  HTML in any case, it isn't really bad either.

  See if that helps.

  Micha

• I changed my password of gmail e-mail. How can I change the password used by Thunderbird to connect to gmail.

  I changed the password used to access my gmail account. Thunderbird still uses the old password to access the account. How can I change the password that is using Thunderbird. The last time this happened I ended up creating a new account to Thunderbird for gmail. Create the new Thunderbird account at least let me enter the new password. I don't really want to have three accounts of Thunderbird for the same gmail account.

  Please do not respond with suggestions on using password manager. I do not use it and do not want to start. I looked, and none of my Thunderbird passwords are displayed here. All I want to do is change the password in Thunderbird. If Thunderbird does not have a feature that allows you to change passwords, should be added.

  The link posted by Christ1 gives WRONG directions. In Thunderbird 24.4.0, is:
  Tools, Options, security, passwords, saved passwords

  Admittedly, in fact, you want that he SHOWS you the passwords, and then you can delete them.
  Once fact you check for mail, it will tell you, it didn't, and then you have the option to enter a new password.
  MUCH too complicated. Time to put the password and the ability to change, in the e-mail account options.

• Satellite Pro U400: How to configure the VLAN for the Marvell Yukon LAN control.

  Hi all
  I need to access the 2 VLANS with the controller LAN Marvell Yukon 88E8072 for my Satellite Pro U400. I installed the necessary Configuration utility network Marvell tell me after installation, VIRTUAL local network settings must be mounted in the Device Manager (Windows 7, right click on computer, properties, click device/network management adapters/double on Marvell Yukon 88E8072 PCI-E Gigabit Ethernet Controller), I can't find a thing to configure here but wake-on-LAN.

  Any suggestion? Thank you!

  Michael

  Hello

  I think that in this case, you can use a network switch.

• How to configure outlook express for hotmail = Icannot sending spare part.

  I had to have a laptop but have a problem with it. Hope someone can help.

  I can send emails via hotmail, no problem. But when I try to send attachments the recipient receives an error message saying: could not read.

  When I tried to configure hotmail/outlook, asked me for some program codes | don't have no or understand.

  I'm a newbie to computer jargon. Please help if you can - many thanks.

  Hi Malcolm,

  1. What is the file format of the attachments that you send?

  2. What is the exact error message when you try to configure Outlook Express with your Hotmail account?

  3. are you having the same problem with other accounts?

  4 program are. which codes you referring?

  To open the attachments, the recipient must have the software file installed in the computer. Without the software, recipient may not be able to open the files.

  To set up Outlook Express, I suggest you go through the following articles of the KB.

  How to configure Outlook Express to use a Hotmail account

  http://support.Microsoft.com/kb/220852

  How to configure Outlook Express 6.0 for Internet mail

  http://support.Microsoft.com/kb/171163

  If the problem is only with Hotmail, then I suggest you to ask your question in the Forums of Hotmail.

  http://answers.Microsoft.com/en-us/windowslive/Forum/Hotmail