How to configure a VM with multiple network cards to see Agent?

How to configure a VM with multiple network cards to see Agent?

We can archive this requirement by configuring the subnet used view Agent.

The subnet determines which view address of Network Agent provides the server instance to connect to view for the client protocol connections. The view on VM officer has more than one NIC

Follow the procedure below:

on a display Agent installed VM,

* Recording of VM session.

* RUN--> type regedit or type regedit.exe at the command prompt

* Create a registry entry to configure the subnet.

For example: is HKLM\Software\VMware, Inc. \VMware VDM\Node Manager\subnet = n.n.n.n/m type - REG_SZ.

In this example, n.n.n.n is the TCP/IP subnet, and m is the number of bits in the subnet mask.

Tags: VMware

Similar Questions

  • Server with multiple network cards

    Hello

    I have a server with multi-port NETWORK adapter running ESXi 5.5.0

    Can anyone remind me how to allocate a VM to port a network?

    or point me to the URL of the full help?

    Thank you all

    The c# Client is that you need to install on your windows computer. The alternative would be the Web Client vSphere. Both are essentially 'vSphere customers. "

    Anyway, you don't need to restart. You can change the network as you want without having to reboot.

  • How to configure ssh on the new network card

    I added a new network adapter to use for replication of virtual machines outside the service console. I can't ssh in the new ip address. I'm tring to figure out how add IP to ssh config so it will allow me to connect.

    You can have several console and you can not remove the console when you are connected.

    As written in the previous post, send a screenshot of the network configuration.

    André

  • When I try to establish a wifi connection, it shows that the problem with the network card is not fixed. How can I solve this problem?

    When I try to establish a wifi connection, it shows that the problem with the network card is not fixed. How can I solve this problem?

    Hello

    Thank you for writing to Microsoft Communities.

    Until we start troubleshooting on this issue please provides us additional information by answering a few questions, this will help us better solutions to the problems.

    1. What is the full error message do you get?

    2. are - that you be able to access or connect to the Internet via wired?

    3 have there been recent changes to the computer before the show?

    Please go ahead and follow the steps mentioned and later a update on the State of the question.

    Method 1:
    Try to run the network troubleshooters. Check if it enumerates and helps resolve the errors.
    http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters

    Method 2: If the problem persists, try to follow the steps from the link.

    In the Windows wireless network connection problems:
    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    Check this link for more information:

    How can I troubleshoot network card? http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

    Why can't I connect to the Internet?
    http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

    Please follow these recommended steps and post if you still experience the problem.

  • How to configure the bluetooth with Kyocera android phone connection to share photos, music & video files

    Original title: Windows 8 Configuration bluetooth with Kyocera android phone?

    Configuration of bluetooth of Windows 8 with Kyocera android phone?  I got a laptop with bluetooth Tech. How can I set up a connection and share photos, music & video files?

    Hey GQ - Jon'Jon,.

    Make sure that Bluetooth is enabled on the computer as well as your Kyocera android phone.

    Make sure that the phone is paired with your computer.

    For information about how to configure the Bluetooth with Kyocera android phone connection to share photos, music & video files, it would be better if get you in touch with Kyocera phone support for assistance. Please see the support link:

    http://www.Kyocera-Wireless.com/support/phone/

    Please feel free to respond if you face problems with Windows in the future.

  • How to configure ESS to the multiple proxy weblogic administration console

    Hello

    We use a 11.1.1.7 OSH and OAM webgate 11g and 11.1.2.

    To bring two weblogic server admin console in Kingdom of Single Sign-on.


    Please let us know how to configure ESS to the multiple proxy console weblogic.

    Thank you

    Stern John

    Activate the configuration of the virtual server on OSH and assign each administration console to another virtual server.

  • How can I force a virtual computer to use a specific physical network adapter in a system with 2 network cards?

    I have a host with 2 network cards system.   I have a NETWORK card for the host computer to connect to my domain.  I have a virtual machine that is a deployment server Windows running Windows 2008 server.   The second NIC is to come and turn off the host machine and will then go to a CIsco 3550.   I need the server VM to use deployment only the second NETWORK card and does not communicate the 1st network card that the host uses.

    Can someone please help?  I'm new to VMware.   The original virtual machine on an esx server and was then converted to VMware server 2.

    Yes, just run the network on this host Editor as well.

  • WLAN, lan, dmz on esxi with 2 network cards

    Hello

    I'm newbie esxi. What I'm trying to achieve on my esxi server is simple firewall/gw between internet (vmnic1), LAN (vmnix0) and DMZ. I have only physical 2 NICs in my server, DMZ should be "completely collapsed DMZ. I intend to have 1 web server (www, ftp) in the DMZ, 2 LAN and smoothwall acting as firewall servers.

    After reading some pdf files and some forum discussions I've come with an attached 'Networking' design.

    Could you experts please check design and advise me how secure is it and where are the potential pitfalls?

    COS you need to manage your esxi server.

    The following work of wll:

    An Esx3i server with two physical network (Teddy) interfaces

    pNic0 connected to the internet

    pNic1 connected to your local network

    3 vSwitches configured, one for each natachasery and one internal vSwitch (DMZ)

    Comments "Smoothwall" configured with 3 network cards, one for Internet, a local network, and a DMZ.

    Guests in the DMZ must be created with vNic on the DMZ vSwitch.

    SmoothWall manages the firewall and passes the correct port_number, etc. to the ip address in the DMZ.

    Kind regards

    Torben Jungsberg

  • Error code 797: connection is not available because there is a problem with your network card or modem

    I have a Windows 7 laptop. I use broadband (DSL) to connect to the internet. Lately, I have an error with the code 797. It says connection is not available because there is a problem with your modem or network card. I have a Sony Vaio e series laptop.

    Hi Muffakham,

    Thanks for posting your question in the Microsoft Community forums.

    I see from the description of the problem that you are unable to connect to the Internet and receive "Error Code 797 connection is not available because there is a problem with your network card or modem".

    I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.

    To provide the proper resolution, that I would need more information on your side.
    Did you the latest changes on the computer before this problem?

    This problem may occur because of damaged or incompatible, drivers connection settings incorrect network, hardware or software problems and missing updates.

    Method 1:
    I suggest you try the procedure described in the article and see if it helps.

    How can I troubleshoot network card?
    Method 2:
    If the problem is not resolved, I suggest you try the procedure described in the article and see if it helps.

    Windows wireless and wired network connection problems
    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    Check out the link for more information.

    Let us know the status of the issue after you perform the troubleshooting steps. If you need information about the problem with the connection to the Internet or get help, I'll be happy to help you. We, at tender Microsoft to excellence.
  • How can you tell what your vSwitch NETWORK card uses?

    We are still at the experimental stage with our ESXi 4.1 installation and have 4 cards assigned to a vSwitch network. 3 are active and it is defined as the day before. Is there a way to tell which network cards are actually get used or are all 3 active cards get used both for the collection of NETWORK adapters? I have attached a few screenshots to view our installation.

    Another thing is that the day before, we noticed NIC for network management and VMnetwork are different and which seemed to have been changed on their own. Is this normal? For example the day before NIC for network management is set to vmnic3 and the NIC for the VMnetwork has the value vmnic2

    Well they are all 'used' to my knowledge.  The only way I've really seen to see one that is circulating is to make a display of advanced host performance and look at networking. From there on, it lists each nic and the amount of data it is to push through. I know that we have 4 s NIC team (similar to your Setup less standby configuration) and usually only a NETWORK card pushes the data at once.

  • How to configure Oracle Discoverer with EBS R12?

    Dear

    I hope that, by default, only oracle Discoverer is not configured with EBS R 12. How to configure?
    Any help, much appreciated.

    Naya,

    Please refer to the next note, it should be useful:

    Note: 373634.1 - using discoverer 10.1.2 with Oracle E-Business Suite Release 12
    https://MetaLink.Oracle.com/MetaLink/PLSQL/ml2_documents.showDocument?p_database_id=not&P_ID=373634.1

  • How to configure the listener with SSL

    Hi Experts,

    I use 11g R2 EE. I want to configure my database listener so that it can be connected using SSL.

    Can someone provide me guide step by step to configure the listener with SSL (including the portfolio so that comes in the image).

    The command line configurations will be well appreciated.

    Thanks in advance

    Alexander gelin

    The client configuration is the same as the server:

    1. create the portfolio.

    2 creating CSR and copy it in CA.

    3. the CSR signal with your certificate root.

    4 copy signed CRT file and root of public certificate to the client.

    5 configure the sqlnet.ora clients.

    Heavy customers already contains the necessary files. For thin clients, it is necessary to install the full or instant client.

    In SQLDeveloper, connection string should be like:

    jdbc:oracle:oci:@(DESCRIPTION= (ADDRESS_LIST= (ADDRESS= (PROTOCOL=TCPS)(HOST=)(PORT=))) (CONNECT_DATA= (SERVICE_NAME=)) (SECURITY= (MY_WALLET_DIRECTORY=D:\Oracle\client.test.p12)))

  • Create multiple virtual machines with 2 network cards

    Hey guys -.

    Been researching some scripts of difference but did not find one who will help me in my situation.

    I'm looking for a script that will allow me to clone model and apply network settings to 2 network cards.

    1 clone Vms + 20 model

    2 Let me send it to a particular lun (using a few LUNS to available)

    3. choose a custom unique specification

    4. apply intellectual property on 2 NICs (primary and backup).

    Any help would be sincerely appreciated.

    Thank you

    Sorry to lose this thread out of my sight.

    What follows is an attempt to meet all the conditions you listed.

    $numberOfVM = 20$baseVMName = "VM"$templateName = "Template"$osCustName = "MyCust"$IPBase1 = "192.168.1."$IPBase2 = "192.168.2."$IPMask = "255.255.255.0"$IPGate1 = "192.168.1.254"$IPGate2 = "192.168.2.254"$IPDns1 = "192.168.1.100"$IPDns2 = "192.168.2.100"
    
    # Target resourcepool$resPool = Get-ResourcePool -Name Resources
    
    # Get the template$template = Get-Template -Name $templateName
    
    # Create a copy of the OS Customisation SpecTry {    Get-OSCustomizationSpec -Name tempOSCust |    Remove-OSCustomizationSpec -Confirm:$false -ErrorAction Stop}Catch {}
    
    $osCust = Get-OSCustomizationSpec -Name $osCustName |     New-OSCustomizationSpec -Name tempOSCust -Type NonPersistent
    
    # Clone the number of requested VM1..$numberOfVm | %{    # Find the datastore with the most free space    $ds = Get-Datastore | Sort-Object -Property FreeSpaceGB -Descending |        Select -First 1
    
        # Update the OS Customisation Spec NIC parts with the IP addresses    Get-OSCustomizationNicMapping -OSCustomizationSpec $osCust |    Set-OSCustomizationNicMapping -Position 1 -IpMode UseStaticIP -IpAddress "$IPBase1$_" `        -SubnetMask $IPMask -DefaultGateway $IPGate1 -Dns $IPDns1 -ErrorAction SilentlyContinue | Out-Null
    
        Get-OSCustomizationNicMapping -OSCustomizationSpec $osCust |    Set-OSCustomizationNicMapping -Position 2 -IpMode UseStaticIP -IpAddress "$IPBase2$_" `        -SubnetMask $IPMask -DefaultGateway $IPGate2 -Dns $IPDns2 -ErrorAction SilentlyContinue | Out-Null
    
        # Create the new VM    New-VM -Name "$baseVMName$_" -Template $template -OSCustomizationSpec $osCust `        -Datastore $ds -ResourcePool $resPool  | Out-Null}
    

    The script will create clones of $numberOfVM of the model. The virtual machines will be created at the root of the bunch, and they will be called VM1, VM2...

    The OSCustomizationSpec needs to exist and must have 2 network cards.

    The script finds the data store with more free space to create each virtual computer.

    Addresses IP of NIC are consecutive, for example on NIC1 you get 192.168.1.1, 192.168.1.2... and so on.

    Let me know if you have any questions.

  • How to configure vCenter Server with an external smtp server?

    Is it possible to configure vCentere Server with an external smtp server?

    In our environment, we must configure vCenter server to send email alerts when the alarms are triggered. We use the google apps (smtp.gmail.com) server as our official email server.

    I know the steps to do the same?

    You must authenticate external messages. Here is one of this tutorial. http://paulgrevink.WordPress.com/2011/02/06/configuring-vCenter-for-email-with-SMTP-authentication/

  • How to configure jdeveloper 11 with the .dbc files?

    Hi all

    I am a new bie here. 4 jdeveloper 10, I can configure files .dbc to the setting of the project, while 4 jdeveloper 11, it's totally different. I can't find any place to set it up. How to configure the .dbc in jdeveloper 11?

    Kind regards
    Chelsea

    You cannot use jdev 11g for the development of the OFA...
    You must download the patch of jdeveloper on metalink to develop objects of the OFA.

    See this metalink note to find the correct version of jdeveloper, you need to download https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=416708.1

    Prasanna-

Maybe you are looking for