How to configure ASA as EZ - vpn client?

How can I configure ASA as Ez - vpn client?

Only ASA 5505 can be configured as a client VPN EZ.

Here's a few example configuration:

http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/ezvpn505.html

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808a61f4.shtml

Hope that helps.

Tags: Cisco Security

Similar Questions

ASA 5520: Remote VPN Clients cannot ping LAN, Internet

I've set up a few of them in my time, but I am confused with this one. Can I establish connect via VPN tunnel but I can't ping or go on the internet. I searched the forum for similar and found a little issues, but none of the fixes seem to match. I noticed a strange thing is when I run ipconfig/all of the vpn client, the IP address that has been leased over the Pool of the VPN is also the default gateway!

I have attached the config. Help, please.

Thank you!

Exemption of NAT ACL has not yet been applied.

NAT (inside) 0-list of access Inside_nat0_outbound

In addition, you have not split tunnel, not sure you were using internet ASA for the vpn client internet browsing.

You can also enable icmp inspection if you test in scathing:

Policy-map global_policy
class inspection_default

inspect the icmp

Hope that helps.

How can I send parameters preconfigured VPN client to a remote user

Dear all,

I have an ASA 5510 using VPN IP - SEC for remote users. I want to send all settings pre-configured for the VPN client.

How can I save the configuration file and send to a remote user?

Concerning

Configure the vpn profile in your vpn client, and then send them the .pcf file located in the directory Program Files/Cisco Systems VPN/customer/profiles. Then all they have to do is import it into their client.

Connected to the ASA via the "VPN Client" software, but cannot ping devices.

I have a network that looks like this:

I successfully connected inside the ASA via a software "Client VPN" tunnel network and got an IP address of 10.45.99.100/16.

I am trying to ping the 10.45.99.100 outside 10.45.7.2, but the ping fails (request timed out).

On the SAA, including the "logging console notifications" value, I notice the following message is displayed:

"% 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; "Connection for icmp src, dst outside: 10.45.99.100 inside: 10.45.7.2 (type 8, code 0) rejected due to the failure of reverse path of NAT.

I have a vague feeling that I'm missing a NAT rule of course, but not all. What did I miss?

Here is my configuration of ASA: http://pastebin.com/raw.php?i=ad6p1Zac

Hello

You seem to have a configured ACL NAT0 but is not actually in use with a command "nat"

You would probably need

NAT (inside) 0-list of access inside_nat0_outside

He must manage the NAT0

Personally, I would avoid using large subnets/networks. You probably won't ever have host behind ASA who would fill / 16 subnet mask.

I would also keep the pool VPN as a separate network from LANs behind ASA. The LAN 10.45.0.0/16 and 10.45.99.100 - 200 are on the same network.

-Jouni

Binds two ISP ASA to remote VPN Client to connect to instead of creating two profiles on the remote client

Hello

just a quick,

TOPOLOGY

ASA isps1 - 197.1.1.1 - outside

ASA ISP2 - 196.1.1.1 - backup

LAN IP - 192.168.202.100 - inside

I have configured Tunnel on the interfaces (external and backup), but is to link both legs public to serve a thare as redundancy for vpn users and users of the vpn tunnel leave pointing inside IP whenever they want to establish vpn sssion, we want it to be one, so if an interface fails vpn users will not know , but he will try the second for the connection. instead of creating the profile for the two outside of the leg on the vpn client.

is this possible?

Hi Rammany.

In your case, you have only an ASA that connects with 2 ISP in another segment IP... 196.x.x.x (Link1) & 197.x.x.x (Link2). What your condition is you want to have the VPN client who must be consulted with backup. If 196.x.x.x link fails, it should automatically take 197.x.x.x link. That too we should not have the config set in the VPN client backup server. You don have the possibility of having standby active also in asa single.

I think n so it will work with your current design.

This option is if your VPN client supports host name resolution (DNS). You can have the VPN created for both the public IP address share the same host name keeping the bond as the primary address 1 and 2 a secondary address. It will work alone.

Hope someother experts in our forum can help you with that.

PIX - ASA, allow RA VPN clients to access servers at remote sites

I got L2L tunnels set up for a couple of remote sites (PIX) for several months now. We have a VPN concentrator, which will go EOL soon, so I'm working on moving our existing customers of RA our ASA. I have a problem, allowing RA clients access to a server to one of our remote sites. PIX and ASA (main site) relevant config is shown below. The error I get on the remote PIX when you try a ping on the VPN client is:

Group = 204.14. *. *, IP = 204.14. *. * cheque card static Crypto Card = outside_map, seq = 40, ACL does not proxy IDs src:172.16.200.0 dst: 172.16.26.0

The config:

Hand ASA config

access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0

access extensive list ip 172.16.1.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0

access extensive list ip 172.16.22.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0

access extensive list ip 172.16.200.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0

access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.200.0 255.255.255.0

access extensive list ip 172.16.0.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0

access extensive list ip 172.16.1.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0

access extensive list ip 172.16.22.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0

access extensive list ip 172.16.200.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0

card crypto outside_map 60 match address outside_cryptomap_60

outside_map 60 set crypto map peer 24.97. *. *

card crypto outside_map 60 the transform-set ESP-3DES-MD5 value

map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

outside_map interface card crypto outside

=========================================

Remote config PIX

access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.0.0 255.255.255.0

access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.1.0 255.255.255.0

access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.22.0 255.255.255.0

access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.200.0 255.255.255.0

access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.0.0 255.255.255.0

access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.1.0 255.255.255.0

access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.22.0 255.255.255.0

access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.200.0 255.255.255.0

card crypto outside_map 60 match address outside_cryptomap_60

peer set card crypto outside_map 60 204.14. *. *

card crypto outside_map 60 the transform-set ESP-3DES-MD5 value

outside_map interface card crypto outside

EDIT: Guess, I might add, remote site is 172.16.26.0/24 VLAN VPN is 172.16.200.0/24...

What you want to do is 'tunnelall', which is not split tunneling. This will still allow customers to join the main and remote site, but not allow them to access internet... unless you have expressly authorized to make a 'nat (outside)"or something. Your journey on the client will be, Secured route 0.0.0.0 0.0.0.0

attributes of group policy

Split-tunnel-policy tunnelall

Who is your current config, I don't see where the acl of walton is attributed to what to split tunnel?

How to configure ASA IPS, which is connected to the Internet

Hello guys,.

I am a beginner in the Concept ASA IPS and that my company HAS an ASA 5520.

Currently, ASA has been connected to the router connected ISP and internet acting as a firewall to control the traffic which

is integrated with Websense URL filtering.

Can you please let me know what all should we expected to configure IPS in this scenario, and what is the IPS feature.

What is the main function of the IPS?

Grateful to your messages.

Kind regards

KA.

KA;

The main function of the AIP - SSM in your ASA 5520 is to perform deep inspection packet and signature matching to detect traffic potential of achievement within your network. If this traffic is detected, the AIP - SSM denying traffic to cross your ASA. Here is a link to a brief overview of the product:

http://www.Cisco.com/go/aipssm

First, you must configure the ASA to divert traffic to the AIP - SSM for inspection, it is shown here:

http://www.Cisco.com/en/us/docs/security/IPS/7.0/Configuration/Guide/CLI/cli_ssm.html

So, you want to make sure that background basket interface (GigabitEthernet0/1) is added to a virtual sensor on the AIP - SSM for allow the inspections to occur.

You want to make sure that the signature on the AIP - SSM definitions are up-to-date. This ensures the most accurate protection from the perspective of the AIP - SSM. This will require an active license be installed on the AIP - SSM.

Then, you most likely want to monitor events generated by the AIP - SSM. To do this, Cisco offers a free entry-level called IPS Manager Express (IME) solution. You can learn more and download IME here:

http://www.Cisco.com/go/IME

You will want to monitor EMI to learn that the potential risks of security in network traffic crossing your infrastructure. When you experience events for which you would like to understand better, you can site IntelliShield visist Cisco for further investigation:

http://www.Cisco.com/security

Details here, can also be extended within the IME event view.

Use of an IPS will be a continuous monitor and learn phase in order to ensure that you are aware of traffic expected and unexpected, and that the appropriate response can be applied. This is something which is different in each environment, so it is not a simple white paper on how to perform these actions.

Scott

Step how to configure ASA 5500 Series Security Services Module-10 (model: ASA-SSM-10)

Dear support,

I need to configure Security Services Module-10 (model: ASA-SSM-10) on my ASA 5510 firewall. Could you provide configuration step and how to connect to the module?

Here is the information on the module

ciscoasa (config) # sh Details of module 1
The details of the Service module, please wait...
ASA 5500 Series Security Services Module-10
Model: ASA-SSM-10
Hardware version: 1.0
Serial number: JAF1115066U
Firmware version: 1.0 (11) 2
Software version: 1.0000 E1
MAC address range: 001a.e268.5aa9 to 001a.e268.5aa9
App name: IPS
App status. : to the top
App status. / / Desc:
App version: 1.0000 E1
Data of aircraft status: Up
Status: to the top
Mgmt IP addr: 133.1.9.144
Web to MGMT ports: 443
Mgmt TLS enabled: true

your help is very appreciate.

Thank you

Best regards

Hi Sothengse,

Please find the samlpe on AIP SSM module configurations. You can go through this to begin with.

http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

https://www.YouTube.com/watch?v=FgYU5ZXwk4g

Concerning

Knockaert

How to configure the default e-mail client

Message that appears indicates "the default mail client is not properly installed" How do I rectfy it.

Original title: an installation correct mailclient

Hello 99noel99,

We need more information in order to properly process your question.
What operating system do you use?
What email program are you using? Outlook, Windows Live Mail, a web mail client?
What do you do when you get this error message?

If you use Outlook, click the article below:
KB Article ID: 312346 -a new message window does not open when you click a mailto link on a Web page in Outlook

To resolve this problem:
Go to default programs, you can achieve in the start menu or via the Control Panel, and then click the first item: "set your default programs."
In the left pane, click on Outlook or your email client.
Click the option on the right as "set this program as default.

I hope this helps.

Marilyn
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think

How to configure ASA 5510 - my first time HA! Help!

I need to connect 2 ASA 5510 in an HA configuration. I don't know about the types of cable (x - ovr or straight) for the connection of the State, heartbeat connection and where they must be connected. Also, I was told that the connection of the State must be on a switch or VLAN separate... Is it true...?

We use a x-over for the failover of an int on the SAA primary to secondary ASA and it works very well.

How to configure the e-mail OSX client

----------------------------------------
Operating system: Mac OS X
Browser: Safari 5.2

When I try to set up an e-mail client, I get this message:
Mail is unable to verify the identity of "samreesor.com".

What I am doing wrong?

Thank you
Cam

Hello Cam,

It is 'technically' not valid because your incoming mail server is mail.samreesor.com that then connects to worldsecuresystems.com which is what BC (secure) runs on.

There is nothing wrong with this message as you (and trust if all goes well) the server you connect too. Just mail to inform you that the name of your server and the originating host name are different, which is what it says at the top of this box. If it's something else that you weren't familiar will, you'd be suspicious.

Click the trust under and select the option to "Always trust this certificate." This will stop the message appear continuously.

Unable to connect to other remote access (ASA) VPN clients

Hello

I have a cisco ASA 5510 appliance configured with remote VPN access

I can connect all hosts on the INSIDE and DMZ network, but not able to access other clients connected to the same VPN.

For example, if I have 2 clients connected to the VPN, customer and CustomerB, with a pool of vpn IP addresses such as 10.40.170.160 and 10.40.170.161 respectively, these two clients are not able to communicate with each other.

Any help is welcome.

Thanks in advance.

Hello

I'm a little rusty on the old format NAT, but would be what I would personally try to configure NAT0 on the 'outer' interface.

It seems to me that you currently have dynamic PAT configured for the VPN users you have this

NAT (outside) 1 10.40.170.0 255.255.255.0

If your traffic is probably corresponding to it.

The only thing I can think of at the moment would be to configure

Note of VPN-CLIENT-NAT0-access-list NAT0 for traffic between VPN Clients

list of access VPN-CLIENT-NAT0 permit ip 10.40.170.0 255.255.255.0 10.40.170.0 255.255.255.0

NAT (outside) 0-list of access VPN-CLIENT-NAT0

I don't know if it works. I did not really have to configure it on any ASAs running older software. There was some similar questions here on the forums for the new format.

-Jouni

Cisco VPN Client and Windows XP VPN Client IPSec to ASA

I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.

PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?

Config is:

!

interface GigabitEthernet0/2.30

Description remote access

VLAN 30

nameif remote access

security-level 0

IP 85.*. *. 1 255.255.255.0

!

access-list 110 scope ip allow a whole

NAT list extended access permit tcp any host 10.254.17.10 eq ssh

NAT list extended access permit tcp any host 10.254.17.26 eq ssh

access-list extended ip allowed any one sheep

access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh

sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0

tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0

flow-export destination inside-Bct 192.168.1.27 9996

IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0

ARP timeout 14400

global (outside-Baku) 1 interface

global (outside-Ganja) interface 2

NAT (inside-Bct) 0 access-list sheep-vpn

NAT (inside-Bct) 1 access list nat

NAT (inside-Bct) 2-nat-ganja access list

Access-group rdp on interface outside-Ganja

!

Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2

Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1

Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1

Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1

Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1

Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1

Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1

Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1

Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1

dynamic-access-policy-registration DfltAccessPolicy

Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

Crypto ipsec transform-set newset aes - esp esp-md5-hmac

Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans

Crypto ipsec transform-set vpnclienttrans transport mode

Crypto ipsec transform-set esp-3des esp-md5-hmac raccess

life crypto ipsec security association seconds 214748364

Crypto ipsec kilobytes of life security-association 214748364

raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1

card crypto interface for remote access vpnclientmap

crypto isakmp identity address

ISAKMP crypto enable vpntest

ISAKMP crypto enable outside-Baku

ISAKMP crypto enable outside-Ganja

crypto ISAKMP enable remote access

ISAKMP crypto enable Interior-Bct

crypto ISAKMP policy 30

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

No encryption isakmp nat-traversal

No vpn-addr-assign aaa

Telnet timeout 5

SSH 192.168.1.0 255.255.255.192 outside Baku

SSH 10.254.17.26 255.255.255.255 outside Baku

SSH 10.254.17.18 255.255.255.255 outside Baku

SSH 10.254.17.10 255.255.255.255 outside Baku

SSH 10.254.17.26 255.255.255.255 outside-Ganja

SSH 10.254.17.18 255.255.255.255 outside-Ganja

SSH 10.254.17.10 255.255.255.255 outside-Ganja

SSH 192.168.1.0 255.255.255.192 Interior-Bct

internal vpn group policy

attributes of vpn group policy

value of DNS-server 192.168.1.3

Protocol-tunnel-VPN IPSec l2tp ipsec

Split-tunnel-policy tunnelspecified

Split-tunnel-network-list value split tunnel

BCT.AZ value by default-field

attributes global-tunnel-group DefaultRAGroup

raccess address pool

Group-RADIUS authentication server

Group Policy - by default-vpn

IPSec-attributes tunnel-group DefaultRAGroup

pre-shared-key *.

Hello

For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.

Please see configuration below:

http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

or

http://tinyurl.com/5t67hd

Please see the section of tunnel-group config of the SAA.

There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.

So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.

Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.

"crypto isakmp nat-traversal.

Thirdly, change the transformation of the value

raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

Let me know the result.

Thank you

Gilbert

Routing issue of Cisco VPN Client ASA

Hi, I use a Barracuda NG for firewalls and I would use a Cisco ASA 5505 for VPN Client connections. But I have the problem that I can't get a connection to the VPN PC connected to the internal network. But I can reach the VPN connected PC from the inside. Here is a diagram of my network:

cisco_asa_prob.jpg

Here the IP Configuration and the routing of the Barracuda firewall table:

screen_shot_2014-08 - 12_at_16.01.42.png

I have a route on the Barracuda NG to the 10.10.10.0/24 network VPN Client on eth0.

The 192.168.1.0/24 LAN I ping the Client comes with Client VPN 10.10.10.11 as it should. But I can't ping or access network resources in the local network for AnyConnected customer's PC that connected through the VPN.

Here is the config Cisco ASA:

 : Saved : : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz : ASA Version 9.2(2) ! hostname leela names ip local pool VPN-Pool 10.10.10.10-10.10.10.200 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 5 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp ! interface Vlan5 nameif dmz security-level 50 ip address 172.16.0.250 255.255.255.0 ! ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server 192.168.1.10 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network VPN-Pool subnet 10.10.10.0 255.255.255.0 description VPN-Pool object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit ip object VPN-Pool any access-list dmz_access_in extended permit ip any any access-list global_access extended permit ip any any access-list outside_access_in extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (inside,dmz) source static any any destination static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 no-proxy-arp route-lookup inactive access-group inside_access_in in interface inside access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz access-group global_access global route dmz 0.0.0.0 0.0.0.0 172.16.0.254 1 route inside 0.0.0.0 0.0.0.0 192.168.1.254 tunneled timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy server-type microsoft user-identity default-domain LOCAL aaa authentication enable console LDAP_SRV_GRP LOCAL aaa authentication http console LDAP_SRV_GRP LOCAL aaa authentication ssh console LDAP_SRV_GRP LOCAL aaa authentication serial console LOCAL http server enable 444 http 192.168.1.0 255.255.255.0 inside snmp-server location Vienna crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto map dmz_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map dmz_map interface dmz crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=leela proxy-ldc-issuer crl configure crypto ca trustpoint ASDM_TrustPoint1 enrollment terminal crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable dmz client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 no ssh stricthostkeycheck ssh 192.168.1.0 255.255.255.0 inside ssh timeout 30 ssh key-exchange group dh-group1-sha1 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.254-192.168.1.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept dynamic-filter updater-client enable dynamic-filter use-database ntp server 192.168.1.10 source inside ssl trust-point ASDM_TrustPoint0 dmz ssl trust-point ASDM_TrustPoint0 inside webvpn enable dmz no anyconnect-essentials anyconnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 1 anyconnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 2 anyconnect image disk0:/anyconnect-linux-3.1.05170-k9.pkg 3 anyconnect image disk0:/anyconnect-linux-64-3.1.05170-k9.pkg 4 anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy DfltGrpPolicy attributes default-domain value group-policy GroupPolicy_AnyConnect internal group-policy GroupPolicy_AnyConnect attributes wins-server none dns-server value 192.168.1.10 vpn-tunnel-protocol ikev2 ssl-client webvpn anyconnect profiles value AnyConnect_client_profile type user group-policy portal internal group-policy portal attributes vpn-tunnel-protocol ssl-clientless webvpn url-list none username tunnel-group AnyConnect type remote-access tunnel-group AnyConnect general-attributes address-pool VPN-Pool authentication-server-group LDAP_SRV_GRP default-group-policy GroupPolicy_AnyConnect tunnel-group AnyConnect webvpn-attributes group-alias AnyConnect enable tunnel-group Portal type remote-access tunnel-group Portal general-attributes authentication-server-group LDAP_SRV_GRP default-group-policy portal tunnel-group Portal webvpn-attributes group-alias portal enable! ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 ! prompt hostname context no call-home reporting anonymous hpm topN enable : end no asdm history enable

Can someone please help me solve this problem?

When I tried to solve this I didn't choose which interface the Packet Tracer?

The interface inside or DMZ interface? Inside, he says it will not work with the dmz but the error did not help me

Anyone here knows why it does not work?

screen_shot_2014-08 - 12_at_16.34.57.png

screen_shot_2014-08 - 12_at_16.33.06.png

Hello

Inside LAN is directly connected to the right firewall VPN... then I don't think you have to have the itinerary tunnele... can you try to remove the road tunnel mode and check.

entrance to the road that is static to achieve 10.10.10.11 as its display is correct...

Route by tunnel watch also with 255 administrative distance. I've never used that in my scenarios... lets see...

Concerning

Knockaert