How to configure the adapter for network WRT54G wireless

Similar Questions

• How to connect the keyboard for apple tv wireless?

  How to connect the keyboard for apple tv wireless?

  If you mean the 4th generation new Apple Tv, you cannot currently. It does not support keyboards at this time.

  If you mean the 3rd generation Apple Tv:

  Use a keyboard Apple Wireless with your Apple TV (2nd or 3rd generation) - Apple supported

• How to find the password for my Motorola Wireless?

  How to find the password for my Motorola Wireless?

  How to connect another computer to the Motorola Wireless?

  ... and now my computer won't connect to the wireless...

  Now would be a good time to use the instructions of the Setup Guide quick Motorola SBG940.

  ... I think I'll call my cable provider then!

  It may be better to talk to someone on the phone instead of trying to communicate via typed messages repeated as some of the information in the previous messages typed always seem to be lost in translation.

• How to configure the switch for JMS bridge

  Hello
  
  I tried with the selector option when working with several bridges, here is the scenario that I applied.
  
  Created five queues ( Q1, Q2, Q3, Q4, and Q5 ) and configured JMS bridge Destinations with each queue with the factory of unique connections ( CF1, CF2, CF3, CF4, and CF5 ) and baptized as D1, D2, D3, D4 and D5.
  Then created JMS JB2 bridges with D1 source and destination as D2. Similarly the JB3 as D1-D3, as D1-D4 JB4 and JB5 as D1-D5.
  And sector for each of the JB2 JB3 and JB4 JB5 as two, three, four and five respectively and reboot after the changes.
  
  Now I expect the following scenario to work
  By pushing the message to Q1/CF1 with two in the content of the message, so wait for the message to be delivered to Q2/CF2 through JB2, but messages is not moved by JB2.
  Similarly, message pushed to Q1/CF1 having three in the content of the message, so waiting for the message to be delivered to Q3/CF3 by JB3, but messages is not moved through JB3. Similar behavior for other messages with four and five in the content of the message.
  
  In the bridge configuration, selected QOS as "Atmost" - once.
  
  Note: all configurations were conducted in the same field and the WL version is 10.3.6.0 *
  
  The example message I am pushing to Q1/CF1 say 'two Test Data'* and expect to reach the queue Q2/CF2
  
  Concerning
  Venkata Madhu
  
  Published by: vv * Sep 12, 2012 13:05

  JMS selectors work normally om jms headers and not on the message.

  In my previous post, I see that WebLogic provides an extension "SELECTOR xpath" in this area, although I recommend using standard selectors when possible. See my previous post for more information on the syntax of the selector, etc.. The best resource on selectors is the javadoc for javax.jms.Message (http://docs.oracle.com/javaee/5/api/javax/jms/Message.html).

• How to change the DPI for Officejet 4500 Wireless settings

  Printer: HP Officejet 4500 G510n wireless (CN547A)

  OS: Windows 7 64-bit

  My DPI settings seem to be too high.  I'm scanning a single page and the file is 21MB in size.  I can't find how to reduce the dpi.

  Is it possible to do it on this device?

  Thank you.

  Hi zulwe,

  You can adjust the DPI and PPI parameters depending on the program you are using. Because you are using Windows as your operating system, you can have this printer Officejet HP solutions Center. Check this box: scanning with HP Solution Center software in Windows

  And no, we cannot do this on the device. It can only be done through your computer.

• Satellite Pro U400: How to configure the VLAN for the Marvell Yukon LAN control.

  Hi all
  I need to access the 2 VLANS with the controller LAN Marvell Yukon 88E8072 for my Satellite Pro U400. I installed the necessary Configuration utility network Marvell tell me after installation, VIRTUAL local network settings must be mounted in the Device Manager (Windows 7, right click on computer, properties, click device/network management adapters/double on Marvell Yukon 88E8072 PCI-E Gigabit Ethernet Controller), I can't find a thing to configure here but wake-on-LAN.

  Any suggestion? Thank you!

  Michael

  Hello

  I think that in this case, you can use a network switch.

• How to configure the VPN for Xperia phones

  I know that this does not work for many after the upgrade to KitKat but I just wanted to know how other users were using previously.

  Could you give me the settings or help me how to use these settings.

  VPN does not of course for a lot, but I guess that Sony will do something so he can fix it. But tell me how you used earlier. I am interested in knowing. Never used because I found it difficult. People told me that it is a sort of proxy to surf the net anonymously.

  Sachin4u wrote:

  ... VPN works of course not for many...

  Where did you get this info? I had this problem a few weeks in this forum channel and no useful response has been posted.

  But anyway: on Android 4.3, I added a VPN connection with the 'IPSec Xauth PSK' type and the pre-shared key. At the opening of the connection, I entered username and password. A few secconds later than the VPN connection to my home network with router Fritz Box has been implemented.

  Hopefully, I could help you, Titus

• How to configure the proxy for firefox androidversion?

  How to set parameter for android version of firefox?

  Thank you

  Hello

  I have had a look and found this page that should help you.

  If this is not the case please come back here and we'll see what we can do to help.

• How to configure the VLAN for Cisco SG500 - switch 28

  Hello

  First of all, it's my first post here, I hope that someone can help me and please be patient because I am very little known.

  OK, so let me explain to you the scénarion I face and I hope someone can help me.

  We have a Cisco SG500 - 28 port gigabit switch in our workplace.

  Our goal is to create 3 VLANs and separate networks between the various departments.

  Vlan1 (which is the default VLAN in the switch)-will be used for the COMPUTER service and management.

  VLAN100 - will be used for business.

  VLAN200 - will be used for clients who need to connect to internet via WiFi.

  I created VLAN100 and VLAN200, and VLAN1 is there by default.

  I want to use port 13 for VLAN200 and to connect the-Wifi access point there.

  The uplink is in port 25.

  I would be happy if you could explain things first to a more general, abstract level, and then we can look at the specific scenario that we have.

  SG500 Cisco - 28 Gets a Sophos UTM 9 router internet.

  I need to take care of the inter - VLAN routing so, subnet and DHCP

  Thanks in advance,

  Sincere greetings,

  D

  Hi Desmond, looking at this DHCP pool it looks correct.

  For the second part, you waant VLAN 200 only work on VLAN 200, that's fine. So if you have an access point, and everything on the VLAN 200 connects to the access point, you can make an access to this list. The access list is entered only, which means the inbound interface.

  So if you have a gateway connecting to #1 port. You'll need to build the access list and apply it to port number 1. That's assuming you make a list of access 'decline' subnet source IP of VLAN 200 destined for the other subnet, that you do not want access.

  The image on another post to fill out your reference numbers, then for the ACL link, it should be placed on the interface VLAN 200 first comes to the switch (IE, the port the access point connects, make sure that you choose to bind by port instead of per VLAN)

  -Tom
  Please mark replied messages useful
  http://blogs.Cisco.com/smallbusiness/

• How to configure the DDC for testing?

  Hi all

  I would like to implement Cisco Secure Desktop in our WebVPN configuration, but I need a way to set up and test without making our existing of WebVPN users.

  It seems to me that if I create a Windows with a criterion that * only * my machine test matches, all other users will fail. If I activate the features "when the location corresponding fails", current users won't see a difference.

  Is this correct? Furthermore, with this configuration, VPN tent making out the CSD software when users connect?

  All advice is appreciated.

  Thank you

  -Steve

  Yes, existing users will not see a difference "when the corresponding location fails. This option "what corresponding location fails" helps Windows customers use VPN to surf the web as a minimum connection option, if the client computer does not match any of the criteria of the configured locations.

• How to configure the application for child object View?

  I have a hGrid standard layout. Two display objects are present, sign in using the link display. I need to define where clause in the child View object. The changes themselves do not appear when I put the where the clause. Also when I try to extract rowCount returns 0 for child View object. But I'm able to get the parent View object value. Any suggestions please.

  Hi Shrikant,

  Thanks for your replies. I was able to find a solution. Was able to achieve thanks to the functionality of the rowset.

  Kind regards
  Pradeep

• How to configure the settings for both tables?

  SELECT GM. GRNNO, GM. GRNDATE, SUM (GS. APPROVED), SM. ISSUENO, SM. ISSUEDATE, GS. ITEMCODE, SUM (SS. ISSUEDQTY)
  OF GS, SM IMS_ISSUEM, GM IMS_GRNM, SS IMS_ISSUES IMS_GRNS
  WHERE GM. GRNMSERIAL = GS. GRNSSERIAL
  AND SM. ISSUEMSERIAL = SS. ISSUESSERIAL
  AND GM. POSTED = 'T'
  AND SM. POSTED = 'T'
  AND GS. ITEMCODE = SS. ITEMCODE
  AND GS. ITEMCODE ='01-01-02-019'
  AND *.
  GM GROUP. GRNNO, SM. ISSUENO, GM. GRNDATE, SM. ISSUEDATE,
  GS. ITEMCODE STOPPED BY GM. GRNDATE, SM. ISSUEDATE;
  
  Here, I have to select the data in the tables between two named parameters: P_1 and: P_2.
  the column date of IMS_GRNM is named GRNDATE.
  the column date of IMS_ISSUEM is named ISSUEDATE.
  How to set these parameters?

  I think what you need is
  Where table1. Column1 between: p1 and: p2
  and table2. Between Column2: p1 and: p2

• How to configure the site for several vpn site

  Hello

  We are in the process of upgrading the IT infrastructure n/w. Our headquarters is home to all servers. I want to establish a vpn between our head office and our 4 stores connectivity.

  Head offfice LAN - 192.168.1.0/24

  Remote Desktop

  1 LAN 1 - 10.1.1.0/24

  2 LAN 2 - 10.1.2.0/24

  3 LAN 3 - 10.1.3.0/24

  4 LAN 4-10.1.5.0/24

  I want to implement the ipsec through our internet vpn. An example of a config would be useful. Thank you

  Not very easy to find an example of a config...

  http://www.Cisco.com/en/us/Partner/Tech/tk583/TK372/technologies_configuration_example09186a0080094525.shtml

  But you have to ORC.

  Federico.

• How to configure the network adapter when you run ESXi on VmWare workstation?

  How to configure the network card installing ESXi on VmWare workstation 6.0.0?

  These are the options: I tried bridged, host-only NAP.  None of them works

  

  What Miss me? driver or adapater?

  I'm running on vmware workstation on Windows 7 with Lenovo laptop.

  in the configuration of your virtual machine, the main issue is memory. you gave the 2 GB of RAM, whereas ESXi 6 cannot go forward without minimum 4 GB of RAM.

  If please have 4 GB of RAM and re-run Setup. you will get through.

  message about the network card should also not appear after that. What kind of network you choose depends on your need.

• How to configure the network home wiFi with dlink router

  I need to create a home network using the dlink WiFi router
  a computer with Vista and the second with XP
  can someone tell me what havo to do to configure the router etc etc o give me same informamation on where I can learn to do
  I want just the old pc with xp for the server and the vista one customer but more importantly I need the file on XP to migrate under vista.
  Thank you very muche for your end of the patient cooperation
  in return, I give free cooking classes
  see you soon

  I'm not sure if you are asking how to set up a secure wireless network, if you ask how to share files between your two computers (and there is no "customer" or "server" in a working group, in a field - which is not), or both.

  So I will give you information on doing both.

  Router - configure manually

  Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

  1. turn off the power to your cable modem.
  2. attach a class (usually supplied with the router) ethernet cable cat5e port Internet/WAN from the router to the ethernet port on the cable modem.
  3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.
  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine. The first thing to do is to change the default password because * all * known default passwords for different routers.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar. ;-)

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). Most computers purchased during the last 4 years have the wireless hardware that will support WPA2-Personal (also known as WPA2-PSK). This is the desired encryption level. If your wireless hardware is older, use WPA. Don't use WEP, because who is easily broken within minutes. So go ahead and set the Security Mode WPA2-Personal. Do this and enter a password. For example, you could use the password ' here be dragons, beware you scurvy dogs! The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the ethernet cable and wireless of the computer should see your new network. Enter the password that you have created (exactly as you wrote it with all capital letters and punctuation) to join the network and start surfing.

  Networking

  Here are the steps of general network troubleshooting. Just cannot apply to your situation, so just take the bits that are. It may seem daunting, but if you follow the steps in the links and suggestions below calmly and consistently, you will have no difficulty to implement your sharing.

  Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

  XP - configure Windows to login automatically (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  Vista - Start ORB > Search > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.
  MS - MVP - Elephant Boy computers - don't panic!