How to connect a USB-wireless printer to a wireless network without PC

Some HP printers do not have a Wizard of wireless configuration integrated into the façade to connect to a network.  These models install to a computer via a USB connection and the software then sends information wireless via the USB cable to the printer.  However, you do not always have a present computer and still need to connect these printers to a wireless network.  You can use a wireless, like an iPad device, to do this.  For the example below, I used an iPad and a printer Deskjet 3510.

The first step is to make sure that your printer is aired at an (Ad Hoc) network.  To do this, turn on the printer and press the wireless or wireless Tower, and then in the Setup menu. Connect the iPad (or other wireless device) to the signal being broadcast by the printer wireless.

Once the iPad is connected to the printer as long as a network connection, open the Web browser on the iPad.  Type 192.168.223.1 in the address bar and go to this site.  Printer status page should load and look like the picture below.

Click the network at the top of the status page.  You can get a quick warning while being redirected to an HTTPS site.  Click Ok in the message box to continue.  When you click OK, you can get a warning about the identity of the server or the certificate.  Select the option that allows you to continue.  The wording can vary from a browser, but there should be an option to continue anyway.

Network status page should now be loaded at this point.  Select Assistant wireless to start the installation of the wireless network and click Next.

When then is selected, it must list the available wireless networks.  Select your network from the list and click Next.  When the network is selected, it should be noted.

Enter the network password if necessary and click Next.

A message should be received indicating the name and if security is enabled.  The message below which must indicate that the settings have been saved successfully.  If it indicates that the settings were saved successfully with an error, the configuration of the network is more than likely operation.  Click Ok at the bottom.

After selecting OK, select status to check that the printer is connected successfully.  It may take a few minutes for light wireless to the printer to stop flashing.  Once it is a solid blue, the printer must be on the network and operation.

Once this is over, then you will be able to reconnect to your wireless (wireless router) normal signal for internet access.  Now, the iPad and the printer are on the same home network.

I hope this helps.

Tags: HP Printers

Similar Questions

  • Unable to connect to the wireless network without help

    2 month old laptop dv7-3162 and it has now stopped working in terms of connection to the Internet wireless. The other computers in the House connect correctly (wireless). So I know for a fact that this isn't a thing of router (my router AND the motem is an all in one device). Now, IV ' e updated my drivers for the latest drivers (only the atheros adapter wireless if it matters) and nothing to fixxed the question. He sees wireless networks, that he just does not connect to them. IV ' e reset and power cycled motem/router several times without success. A ran a windows update and several reboots.

    Thanks in advance

    He worked, all you have to do is go in the device management and wireless network card driver, disable, restart, let it reinstall, and it should work. It did in my case.

  • 2 PC XP and a new Windows 7 pc + 1 Hub Intena - how to connect to a wireless network?

    I have 2 PC with Windows XP and a new one running Windows 7, but unable to connect them so that they run all on a home network. Connection Internet is via a hub Intena broadband.

    One of the XP PC can not even connect to the internet.

    What should do? Any help is appreciated...

    PDW

    Hello

    To check the PC that cannot access the Internet read this page, http://www.ezlan.net/wireless.html

    ------------------------
    Sharing.

    Maybe this can help.

    Win7 when configured on the peer-to-peer network has three types of configurations of sharing.

    Homegroup = only works between Win 7 computers. This type of configuration, it is very easy to entry level users to start sharing network.

    Network of home or work = fundamentally similar (and better) to the previous Working Group sharing methods which allow you to control what, how and to whom the records would be shared with.

    Public share
    = network Public (as Internet Café) in order to reduce security risks.

    To get best results connect to each computer system screen and set all the computers to be on a bearing the same name of Working Group , while each computer has its own unique name.

    http://www.ezlan.NET/Win7/net_name.jpg

    Make sure that the software firewall, AV, or other security components allow free local traffic on all network computers. If you use the 3rd group of security, firewall native Vista/XP must be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

    General example, http://www.ezlan.net/faq.html#trusted
    Please Note that some 3rd party software firewall/AV/security costumes continue to block aspects of the Local traffic even it they are off (off).
    If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic.

    If you end up with the 3rd party software uninstalled or disabled, make sure that Windows native firewall is active .

    ------------------------------

    Network Win 7 with another version of Windows as a work network (works very well if all computers are Win 7 also).

    In the center of the network, by clicking on the type of network opens the window to the right.

    Choose your network type. Note the check box at the bottom and check/uncheck depending on your needs.

    http://www.ezlan.NET/Win7/net_type.jpg

    Win 7 - http://windows.microsoft.com/en-us/windows7/Networking-home-computers-running-different-versions-of-Windows

    Win 7 network sharing folder specific work - http://www.onecomputerguy.com/windows7/windows7_sharing.htm

    Vista file and printer sharing - http://technet.microsoft.com/en-us/library/bb727037.aspx

    Windows XP file sharing - http://support.microsoft.com/default.aspx?scid=kb;en-us;304040

    In Win XP Pro with simple sharing Off, you can visually see the Permission/security level and set them up at your convenience.

    http://www.Microsoft.com/windowsxp/using/security/learnmore/AccessControl.mspx#securityTab

    Sharing printer XP - http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

    Setting Windows native firewall for sharing XP - http://support.microsoft.com/kb/875357
    Windows XP Patch for sharing with Vista (no need for XP - SP3) - http://support.microsoft.com/kb/922120

    When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

    -------------

    If you have permission and security issues with Vista/Win7, check the following settings.

    Point to a folder that wants to share do right click and choose Properties.

    In the properties

    Click on the Security tab shown in the bellows of the photo on the right) and verify that users and their permissions (see photo below Centre and left) are configured correctly. Then do the same for the authorization tab.

    This screen shot is to Win 7, Vista menus are similar.

    http://www.ezlan.NET/Win7/permission-security.jpg

    The Security Panel and the authorization Panel, you need to highlight each user/group and consider that the authorization controls are verified correctly.

    When everything is OK, restart the network (router and computer).

    * Note . The groups and users listed in the screen-shoot are just an example. Your list will focus on how your system is configured.

    * Note . All the users who are allowed to share need to have an account onall computers that they are allowed to connect to.

    Everyone is an account, that means a group of all users who already have an account now as users. It is available to avoid the need to configure permission for each on its own, it does not mean all those who feel that they would like to connect.

  • Connection to the wireless network printer

    My power went market last night and now my Deskjet 3050 a is no longer connected to my wireless network.  How to reconnect?  I don't have a usb cable to connect the computer to the printer.  It's the first time that this has happened - I've had this printer for over 2 years now.

    OK, I pulled down the manual and you do not have an installation wizard, sorry. You will need to use a USB cable from the printer and follow the instructions on page 32 of the User Guide to get back attached to your router.

  • How to connect hPa photo smart printer while a C4385 on I pad

    I'm trying to connect to Apple IPad Wifi 16 GB white for my HP C4385 photo smart printer but all I get is I printer is not found. Can anyone help please.

    Hello

    Your printer is only USB connection, does not supports AirPrint and other mobile printing tasks:

    http://support.HP.com/us-en/product/HP-Photosmart-C4300-all-in-one-printer-series/3221640/model/3221645/document/c01122227/

    This is why your iPhone won't be able to find it. You need an AirPrint, ePrint or printer of cloud which can be connected to a wireless network to be able to print from mobile devices.

    Kind regards.

  • HP LaserJet 200 colorMFP M276nw connects to my wireless network, but will not recognize the printer

    I am trying to set up my wireless printer, and the printer says its is connected to my wireless network, but I can't get my computer to print wireless if I disconnect my regular network and attach the direct wireless network name, which is different and stops my internet to work. How can I get my computer to recognize the printer on my regular wireless network?

    Hi @lelg,

    I understand that you want to configure the printer on the wireless network. I can help you with this.

    Uninstall the printer software.

    Uninstalling the printer software.

    Restore the default settings of the printer.

    Go to Configuration, restore the default values.

    Cycle power to the router and the computer.

    Run the installer on the printer wireless.

    Go to the configuration, Setup, menu wireless network, Wireless Setup Wizard.

    Print a configuration page to get the IP address of the printer.

    Print a Configuration report.

    Select the method.

    If you have a valid IP address for the printer, then try and access the Web built-in to the printer server. Type the IP address in the address bar of your web browser. (Internet Explorer)

    If it loads the page from the network printer then the printer is on the network.

    Download, save, and then run the installation of the software. Color HP LaserJet Pro 200 pilot M276nw MFPS.

    Select your operating system, click Next and click on the software to download and install.

    Test the printer.

    What operating system do you use? How to find the Windows Edition and the Version on your computer.

    Please provide detailed results if you're still having problems.

    Good day!
    Thank you.

  • using the KDL-46W700 how to connect to the wireless keyboard and wireless mouse

    Hello

    I use KDL-46W700 how to connect to the wireless keyboard and wireless mouse

    Unfortunately, you can not connect a keyboard wirelessly on your TV. Your TV will need a driver for this. Sad thing, it's impossible to install anything on the tv, which includes the driver for the external devices such as a wireless (except USB) keyboard... I recommend the SIDEVIEW TV application that has the remote control / function keyboard and mouse... this app is free and can be downloaded via Google Playstore... ^^.

  • When I try to connect to my wireless network, that it asks a security key how do I find the key my router is a comtrend CT-5363

    When I try to connect to my wireless network, that it asks a security key how do I find the key my router is a comtrend CT-5363

    Hello

    1. what operating system do you use?

    2 did you change on your computer?

    3. who is your internet service provider?

    If you use windows7, I suggest you to follow the steps from the links and check out.

    Set up a wireless router

    http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

    Network connection problems

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

    Set up a security key for a wireless network

    http://Windows.Microsoft.com/en-us/Windows7/set-up-a-security-key-for-a-wireless-network

  • How to xp 64 pro wireless network connection wizard

    I installed xp64 pro on my desktop and a dlink wireless card but there is no wireless connection wizard. How and where can I get a wireless network connection wizard. I also tried to get for xp64 sp2 but could not find.

    Hello

    · What is the number and the model of the computer?

    You can check the link below which has steps on how to set up automatic wireless network configuration: http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/wlan_client_configure.mspx?mfr=true

    You can download Windows Service Pack 2 for Windows XP Professional, x 64 Edition: http://www.microsoft.com/download/en/details.aspx?id=17791

  • my printer and computer are both connected to my wireless network, but I can't print documents

    I have a HP Photosmart 6180 and am using Windows Vista.  Both the printer and the computer indicate that they are connected to my wireless network and my computer shows my printer on the network.  When I try to print a document from my computer, nothing prints and printing on my computer says a mistake of the printer.  The printer itself works fine and HP diagnostics indicate that everything is ok.  Any suggestions?

    OK, go to start > Control Panel > printers and delete all instances of the printer.

    Next:

    1. make sure the printer is on and connected to your network. Verify that you can access the printer's internal web page by accessing its IP address before continuing. Get his IP address for a network Test printed on the front of the printer.
    2. click on > start > Control Panel > printers.
    3. click on add a printer
    4. Select local printer
    5. Select create a new port and select Standard TCP/IP Port, and click Next.
    6. under device type, select TCP/IP Device. Under the name of host or IP address, enter the IP address of the printer. Click Next.
    7. Select Hewlett-Packard in the list of manufacturers and select and select your printer model. Click Next.
    If your printer model is not in the list, then select disk provided, browse the CD that came with your HP printer and select the first file begins with hp and ending with INF. click Open, then OK. Select your printer model. Click Next.
    8. If prompted, use the driver that is currently installed.
    9. He will ask the name of the printer - enter a new name or use the one existing. This will be the name of the printer that you select from other applications.
    10. we may ask you to share the printer. Choose No.
    11. the printing area of Test Page is displayed. Go ahead and print it out.
    12. click on finish.

  • How to remove or delete network domestic (not homegroup) so that I can access and connect to our wireless network.

    I have Windows 7 and it is connected to the network via a home network (not homegroup - that is not disconnected).

    We have a set up wireless network and the other computer, tv, xbox, cell phones, tablet, that all were connected successfully to our home wi - fi configuration. My Dell windows 7 is always connected through an old home network of a previous wired router. How in the world I remove, delete or otherwise change the settings so that I can connect to the wireless network. My computer does not even list or recognize the wireless network. Help, please. I looked and looked and can't find anything to help me.

    My computer does not even list or recognize the wireless network.

    If your machine does not list the wireless networks, this is caused by one of the following:

    • There are no active of nearby wireless networks.
    • The machine doesn't have a wireless adapter.
    • The wireless adapter is disabled.
    • The wireless adapter is disabled. Most laptops have a switch or some facility keyboard to turn off the wireless network card.
  • How can I disable 'O2 connection manager' to automatically connect to the wireless network?

    Original title: I have a program installed in my computer 'O2 connection manager' it automatically connects to the wireless network, I need to disable the connection

    I have a program installed in my computer 'O2 connection manager' it automatically connects to the wireless network, I need to disable the connection to the network.

    Hi John,

    I imagine the inconvenience that you are experiencing. I will certainly help the question of fixing.

    If you do not O2 connection manager, you can disable it to connect to the Internet or you can uninstall the program and check the issue.

    You can follow the steps in the link below.

    Uninstall or change a program:
    http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program

    I would say O2 you back for more information in the links below:

    http://www.O2.co.UK/business/support

    http://community.o2online.IE/

    I hope that the information above helps you.

  • Photosmart C4599 connects to the wireless network

    System details: Windows 7 64 bit, HP Photosmart C4599 Limited Edition. Wireless network (Netgear router) with visible SSID and MAC filter.

    As the title suggests: my wireless printer is not connecting to my wireless network more. The reason that it is 'more' is because he used to work. But my wireless router has started to lose the internet connection - and I read somewhere that it might work to change the broadcast channel of the router (instead of channel 11 to 13). And it helped.
    But since then, the printer was not able to connect. I tried it back - and interruption of the internet connection but the printer worked (a little).

    I tell myself that I have to reset the wireless printers Setup, I don't know how to do.

    Ok.  I think that the issue would be with the channel.  It might be too high a frequency for the printer to communicate properly.  You can have a heavy traffic on any channel, it depends on what is around you.  I recommend trying channel 1 or 6.  You should be able to download a parser for your smart phone wifi see what are the channels have less useage.

  • Can I update my system to connect to a wireless network?

    is it possible to convert a vista inspiron 530 for a wireless connection

    I run an Inspiron 530 Vista OS, it's the outside improved power supply basic package and the graphics card.

    Hello

    1. Why do you want to be upgraded to connect to the wireless network?

    2. are - what you are talking about to upgrade to Windows 7?

    As you are using a desktop computer, you must purchase and install a Peripheral Component Interconnect (PCI) wireless adapter or a USB wireless adapter, and then you will be able to connect to the wireless network.

    Once you purchase and install the adapter, please try the steps in the following Microsoft articles.

    Set up a wireless network:

    http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-wireless-network

    View and connect to available wireless networks:

    http://Windows.Microsoft.com/en-us/Windows-Vista/view-and-connect-to-available-wireless-networks

    And see also the following Microsoft article:

    http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-know-if-a-wireless-network-is-secure

    Hope the information is useful.

  • PC cannot connect to the wireless network

    Windows Vista and office computer HP.  The use of the Airport Extreme.

    All other computers in the House can connect to the wireless network.

    The Vista machine declined the connection Wireless intermittently for the past two weeks.  Tonight, he lost it completely.  When I click on "connect to network" in the network control panel - I see the wireless network.  But when I click on connect, I get a message that Windows cannot connect to this network.

    I changed the password on the Airport Extreme and rebooted, it.  Wireless usb on Windows machine the device works correctly, by checking through the properties box.

    For example, Vista machine is recognizing the wireless network, but does not connect. Why not?

    I'm ready to throw the computer out the window!

    Hello

    Check the PoodlesAway solution to the same issue here:

    http://social.answers.Microsoft.com/forums/fi-fi/vistanetworking/thread/d4fa044e-8C41-4D8D-a4b1-82ee9ff556ac

    ======================================

    Apple Airport may be your main problem - did you check its firmware?

    Read these
    http://osxdaily.com/2009/09/01/how-i-fixed-my-dropping-wireless-airport-connection-problem-in-Snow-Leopard/

    http://reviews.CNET.com/8301-13727_7-10331876-263.html

    ======================================

    Actually try updating your driver and disabling the network logon.

    Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
    version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
    Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    Download - SAVE - go where you put it - right click – RUN AS ADMIN.

    You can download several at once however restart after the installation of each of them.

    After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
    manufacturer of system become your backup policies).

    Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
    updated drivers.

    I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
    are almost always old, and you can search drivers manually as needed.

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    ------------------------------------------------------

    Make sure you know the details of connection to your wireless router - SSID and password.

    You lose connection when you do and have to redo your logon.

    Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
    lower left click on merge or delete network locations - REMOVE all instances of your network (and the
    others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

    -----------------------------------------------------

    Check this box:

    Strange problem with Internet under Vista
    http://www.catonett.com/blog/archives/194

    Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
    http://support.Microsoft.com/kb/928233/en-us

    ----------------------------------------------------

    And:

    Network connection problems
    http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

Maybe you are looking for

  • I pay monthly for apple music but now do not have access

    matter of fact, they drafted the 9.99 on 18. All of a sudden I "try a 3 month trial now!  pop up as if I don't have a subscription. I don't want to lose all my songs-Im pretty tech ignorant so I have no idea what's wrong, but I can't download anythin

  • Satellite A300-1NO - Power Saver crashes

    Hello I get a fatal error when starting electric saver application, code 0 x 2 I have a Satellite A300 1NO with Windows XP. When the energy saver tries to start it gives this error code and accidents. This happens with the installer to start too. Ass

  • Satellite M35 won't start

    Hello I received a laptop from a friend who asked me to try and fix it. The problem, it seems to have is the following: When you press the power button, the phone begins to launch, the Toshiba logo appears on the screen as well as the message press F

  • Failure to Assistant Installation C4780 with win7 64-bit

    New dell Inspiron 5040 win7 64-bit home premium service pack 1. Fix the USB, printer concludes "c4700 family" then says 'driver not found problem' (why not Hat in Win7 anyway?). Download drivers basic and full of either uncompressed, then fails sayin

  • Pavilion g6-1250ey

    Hello I have HP pavilion 1250ey g6 with i5 - 2430 m and I want to put it in i7-2670qm, it will support this processor i7-2670qm