How to control the two analog outputs at a time

Similar Questions

• SMU-6556 - how to control the rise in digital lines (hsdio) time

  Hello

  Is it possible to control the rise in digital lines SMU-6556 time?

  Even in a low frequency 10 kHz signal rise time is 2ns.

  TKS,

  Hello engfpe,

  The SMU-6556 is a 50 Ohm system, which means that the output is source series finished to be 50 Ohms and all our cables and accessories are 50 Ohms.  With this configuration, regardless of the flow of data, you should have a clean edge up or down, regardless of the data rate. The quality of the production (edge up or down) on your device is related to the adaptation of impedance of your cables.

  The SMU-6556 cannot adjust the speed of scanning by itself.  However, you can insert simple passive components to do it for you.  I have attached below the images.  The first is a diagram showing a way to slow down the edge.  The second is the a waveform simulation showing the rate of original edge before it slows down and the edge of idle.   This simulation is not the SMU-6556 but rather a generic digital output for concept.  In the schema that R1 is set on 34 Ohms because U1.8 has the 16 additional Ohms on the inside.  TL1 is the output of 50 ohms simulating the cable on the SMU-6556.  R2, R3, and C1 are components, you can insert after the SMU-6556 twist before moving your device/cable.  In this configuration from cable to your device is TL2 which is also 50 ohm, but it could be another impedance in which case you would change R3 to match.

  You can see in the attached images, you can slow down significantly the edge with this configuration by altering the C1.  I hope this helps.

• How to control the output voltage?

  Good time after some time can get the output voltage, but this value is alwayscontinuous. How to control the voltage output through a Boolean? In

  in order to get this tension when I want to.

  Greetings.
  Hugo Santos

  Hi Hugo,.

  If you use a LabVIEW project, you must set the time of sampling in the properties of the node (see SamplingInterval.png). But this time to refresh the data should be high enough. If you take into account this update of time trying to control your way out.

  Kind regards

• DAQmx how to control the level of tension AO paused for a relaxing break?

  I have an application where I need to generate a waveform of a fixed frequency (~ 200 kHz) and the amplitude, but for differing them burst lengths and different lengths of time between bursts. These bursts and these delays are controlled by a line of DIO to generate the relaxing break. I also need to have the output voltage analog voltage controlled between bursts of waveform. I explored using various trigger options, the break seems to be the best solution, but I'm difficult to control the particular point of the end of the waveform during the break occurs to make sure that the break is at the same specific voltage when the wave is hidden. I try to adjust the position of the example 'Analog output Pause for the periodic Signal with regeneration on specimen' but cannot get regular tension during the break I'm after. I use a card Series DAQ. X is there a simple way to pre-set the tension that will be broadcast during the paused state when using a relaxing break? I was not able to find it in the examples or documents. I can't use the code of reference AO set example because it is a software-driven and does not fit into the model of schedule I need to generate.

  Hello

  I don't think there is a way to establish a certain level on the analog output, based on a relaxing break.  I watch using a redeclenchables task analog output and do every hour of beginning to the required voltage.

• How to control the number of lines of text below the image in the slideshow module?

  Lightroom 3.3

  How to control the number of lines of text below the image in the slideshow module?  I have an image with 36 words in the caption field which exports like two lines GOOD.!  I have another image with 57 words in the field of legend who runs the page and shows only a VERY BAD line.  With 57 words I can't do the single-line text box small enough to keep the text does not spread out of the page.

  Ideas?

  On the Mac platform and I expect similar under Windows, just hit enter or return key will not help. Instead, you will have to hit the keys Ctrl + Enter or Ctrl + return. This forces a new line. Windows may use a different modifier key. The screenshot below shows that it is possible. Unfortunately, you need to add the text via the caption or Description field in the library module.

  

• Satellite M100 with Debian - how to control the power and the cooling fan on

  Hey,.

  I M100 and I installed debian, works very well, but there is a problem.
  Cooling fan turns on the top speed of all time. I m not shy on unix.
  How can I control cooling fan?
  How to control the power to the laptop?

  Hi mate,

  have you ever heard of the toshutils? I highly recommend trying these tools. Just google for toshutils and you'll find a few nice applications. Should usually be included in the distribution you have, also, I would check with 'apt - get search toshutils.

  See you soon

• How to control the speed of the fan on Satellite A660 - 11 M?

  Please any body know how to control the fan speed its always of 69% and making bad noise and the cpu use is 3% no to treatment high I try avancΘs power but still runing high speed

  Advanced power settings go to Toshiba power Saver saver > cooling method. There are minimum level. Change back to your power management for a second power plan, and the fan must be much quieter.

  I did it on my Satellite A660.
  Before changing PC Toshiba, health monitor showed CPU temperature 41% and the speed of the fan was 67%. After changing the method of cooling fan speed is 0%.

• How to tie the two serial numbers using test including the tie in the database.

  I have two separate committees, I need to link the serial number too.  One is being tested as a separate unit, then the two are tested together, I need to make sure that I connect them in the database.  Don't know how to do it, looking for any input I can get.  Using a labVIEW vi to request the entry of a Board, and then use information interface to USE testbed for UUT of the hand.

  I have juries, one of the boards, A onboard, was tested by a different sequence file, then A is connected to Board B, and then they are tested as a complete set.  Received a few suggestions on how to save the two serial numbers, but went with a popup message added types of step (modified record results), and then just have the user scann the second number in and it stands as one of the results of the step in the database.

• I try to combine a picture of my sister with a picture of a poem next to her. How to combine the two into a single photo?

  Paint or Windows Photo Gallery

  I try to combine a picture of my sister with a picture of a poem beside it, how to combine the two into a single photo?

  If you have the poem recorded in an image format,
  the following freeware can create a side by side
  Panorama.

  (FWIW... it's always a good idea to create a system)
  Restore point before installing software or updates)

  Download IrfanView
  http://MajorGeeks.com/IrfanView_d4253.html
  (filename: iview433_setup.exe)
  (uncheck if you don't want Google Chrome)

  Download plug-ins too...

  IrfanView plugins
  http://MajorGeeks.com/IrfanView_PlugIns_d4908.html
  (filename: irfanview_plugins_433_setup.exe)

  When the program is installed... read more...

  Open IrfanView and go... Image / create the Image of the Panorama...
  (this will open the screen to "Create a panorama image")

  On the screen to "Create a panorama image"... left click on the add images"" button.
  (Displays the 'Open' screen. Now, drill down to the
  the folder that contains your saved Photos of veterinarians.

  Now... click left (highlighted), the two images, you want to join.
  (you can select more than one if you hold down your Ctrl key)
   
  The two images highlight... left click on the button 'open '.
  (Or... you can add the images one at a time... which is always easier)

  Now, go back to the screen "Create the panorama image.
  and the file names of the selected pictures need to be in the
  Field "Input Images.

  Now with the names of two files in 'Images of entry' field...
  You can left click on the button 'create Image '.

  (the positions left and right of these images can be swapped in)
  selection of a file name and using the "mount image" / "Move."
  Images down"buttons...)

  Now you should see a display of the combined image.
  Reach... File / save as...

  Choose a backup location / enter a file name / choose a format...
  On the left, click on the button "Save..."

• How to break the two folders that are cross-linked?

  I tried to move C:\users\richard to E:\My Documents ' My Documents'.

  Some how the two directories have become reticulate.

  Make any change in directory caused the same change in the directories of the sentence.

  How to restore the two inventories back to normal?

  I tried to move the directory in E:\ back to C:\, but received a parsing error.

  TIA,

  Richard

  Wednesday, February 5, 2014, 17:20:47 + 0000, Richard332 wrote:

  I tried to move C:\users\richard to E:\My Documents ' My Documents'.

  Some how the two directories have become reticulate.

  Make any change in directory caused the same change in the directories of the sentence.

  How to restore the two inventories back to normal?

  I tried to move the directory in E:\ back to C:\, but received a parsing error.

  The directory c: is not really a directory; It is a library which is
  just a pointer to the real directory on E:, a bit like a shortcut.

  So if you get there via the library or the directory, you are in
  in the same place - E:\My Documents and any changes there are also
  See in the library.

• How to control the ws appeal period

  Hi Experts,

  I use bpm12.1.3, when the process web service using the service task, how to control the delay?

  Best regards

  Hi user,

  There is a nice blog on wait times. It's about 11g, but it also applies to 12 c.

  https://technology.AMIS.nl/2011/11/18/timeouts-in-Oracle-SOA-Suite-11g/

  Antonis

• How to control the movement of the oam in muse & just play once the proposal?

  How to control the movement of the oam in muse & just play once the proposal?

  This must be configured during the creation of the oam, no Muse, but the animated application you use.

  Thank you

  Sanjit

• How to control the length of the field... ?

  Hi all
  
  
  All by providing payment details in the payment.jsp... If we use a credit card which has 16 digits then, how to control the ground to allow the entry of 16 digits only... ?
  
  
  Thank you
  Vishnu

  Write javascript to enter only numbers and set the "16" size = attribute to limit the size to 16 digits.

  JavaScript can be like that of google.

  function isNumberKey (evt) {}
  charCode var = (evt.which)? evt.which: event.keyCode
  If (charCode > 31 & (character code < 48="" ||="" charcode=""> 57))
  Returns false;

  Returns true;
  }

  -Kiss

• How to control the length of field, select items list to 4.2 page

  I apologize in advance if I ask what is obvious, but simply, I couldn't get a response yet:
  
  I would like to know how to control the length of the elements of the type selection list page 4.2
  (as for a normal textfield: in the case where the content is longer than simply not all appears on the screen)
  
  help much appreciated
  see you soon
  Wim

  WimDeGroot wrote:
  I apologize in advance if I ask what is obvious, but simply, I couldn't get a response yet:

  I would like to know how to control the length of the elements of the type selection list page 4.2
  (as for a normal textfield: in the case where the content is longer than simply not all appears on the screen)

  Normally the browser automatically resizes the selection list based on the content.

  What version of the browser / do you use?

  What theme?

  What model page/region?

  What form/article layout?

  What content does not match?

  (Basically the best way to get help with problems of this type is to reproduce on apex.oracle.com and see us actually...)

• How to control the service console in ESX?

  How to control the service console in ESX?

  http://www.Petri.co.il/5-critical-VMware-ESX-CLI-network-commands.htm

  http://download3.VMware.com/VMworld/2006/mdc9694.PDF

  http://download3.VMware.com/VMworld/2006/mdc9807.PDF

  http://download3.VMware.com/VMworld/2006/tac0028.PDF

  http://download3.VMware.com/VMworld/2006/tac9689-b.PDF

  http://download3.VMware.com/VMworld/2006/labs2006/VMworld.06.Lab04-performance-manual.PDF

  http://www.RTFM-ed.co.UK/

  PS: If you have found useful messages then please leave a few points

  André