How to find the time to process a request?

Similar Questions

• How to find the time to what zero crossing point occur using zero crossing vi

  Hello 
  Im trying to find the time to the point of inflection of a Bio-Signal with the 2nd derivative, then detecet the point of zero of the derivative signal
  What I need, is to mark the point of inflection on my Bio-Signal at the point where the derivative signal crosses the zero.
  

  The second has two scales on the graph, one on each side.  The first has only a single scale. I do not change the name of VI, so both have the same name.

  Lynn

• How to find the time between two channels of entry in the data acquisition card or pci 6036

  Hello

  I read a lot-related posts on the simultaneous measurement of two input voltage of similar channels in map data acquisition. I know that the best material is "simultaneous measurments of the Series DAQ cards" but I only pci data acquisition card 6036 and I try to understand what is the time between the reading of the two channels . This period is always constant? (must it rely on a voltage (amplitude, frequency, waveform..). I send the sine wave (s) to the two channels and read the values of V, if they read the same value, the difference should always be zero but I get-0,002 to 0.002 Volt difference (I must find a way to convert it in time). A screenshot of my VI is attached. I wonder how I can accurately measure the time delay between the channel.

  I am open to any suggestion, my final goal to read exactly two channels at the same time ((ou connaître le délai exact donc je peux correspondre les données correspondantes étant donné le temps de retard))

  Hi spinup,

  better you should post your question in the forum of LabVIEW, LabWindows/CVI is used

  Good luck.

• says that there is an update of firmware available for my 3 t time capsule. I get "an error occurred when downloading". How to find the problem?

  I said that there is an update of the firmware available for my 3 t time capsule. I get the message "an error occurred when downloading". How to find the problem? I have elcapitan 10.11.6 and capsule version 7.7.3

  Try temporarily, connect your MacBook Pro to your Time Capsule using an Ethernet connection... If not already, then try downloading the firmware again.

• How to find the reason for the high use of the processor - shared server process?

  Hello

  I have a Linux server with instance and an oracle 11.2.0.3. The database is configured for shared server. I do not know the application using the database, but they have performance problems. When I check the server I see, that ora_s001 use a processor Core with 90 to 100%. Is there a way to know the reason for the high CPU load? I'm not very adept at finding bottlenecks or bad sql statements. What I found ist, that some users have very high logical_io and the same users have much cpu_usage.

  What can I do next? Thanks for the tips.

  You must Server multi-user shared for this number of sessions. The main objective os using MTS is reducing the memory usage on the server for the UGA and PGA of sessions.

  About the CPU usage, you must session which uses this server shared at the time, with process $ v and v$ session to trace. From there, check the SQL_ID running and then get his stats. This is probably one or two SQLs with large number of I/o logic. This happens most of the time due to incorrect cardinality estimates and/or bad statistics on the subject which causes suboptimal plans to generate.

• How to find the OS ppid in v$ session and V$ process

  Hello
  
  Oracle 11gDB
  
  I have this suspiscious process in my session of $ v which is always running and connected to a 'HR' scheme, even if the 'HR' application is also stopped and other HR related batch process.
  And he also told me that it came from the UNIX sun-server1. My problem is that I can not locate the PPID OS for this process when I login to the operating system to the Sun-server1.
  I tried to kill this session, but he maintains the connection. Even if I bounce the database, it come back.
  
  How to find the source of this process to the Sun-server1?
  
  I tried this script:
  

  SELECT     p.program, p.spid
  FROM v$session s, v$process p
  WHERE s.paddr = p.addr
  AND s.sid IN (39)

  Program                                                 Spid
  ============    ====
  ORACLE.EXE (SHAD)     6404

  But if I have a ps - ef | grep 6404 there is no existing process OS. No matter what other script that can identify the process id of the operating system?
  
  
  Thank you very much

  KinsaKaUy? wrote:
  Thanks Sb, what is your new name :)

  Who do you think is the culprit?

  root@sun-server1 # ps -ef|grep "May 16"
  v231sys  7065  7051   0   May 16 pts/1      11:16 /usr/jdk/jdk1.5.0_13/bin/sparcv9/java -server -Xms1024m -Xmx1024m -XX:MaxPermSi
  v231sys  7051     1   0   May 16 pts/1       0:00 /bin/sh startWebLogic.sh V231_ABDC
  root 13117 11928   0 12:56:30 pts/3       0:00 grep May 16
  v231sys  7229  7065   0   May 16 pts/1       1:17 /opt/SPLcobAS51/bin/cobjrun64 -Dcom.microfocus.cobol.cobjvm=sun_150_64 -DSPLCJV
  v231sys  6257  8518   0   May 16 pts/1       0:00 bash
  v231sys  7211  7065   0   May 16 pts/1       1:17 /opt/SPLcobAS51/bin/cobjrun64 -Dcom.microfocus.cobol.cobjvm=sun_150_64 -DSPLCJV
  

  When the process lasts more than 24 hours, you can get is no longer hours or minutes.
  You can use the utility "netstat" to connect the source & destination?

  If this isn't the case, random randomly start put to death via kill - 9 until you success!

• How to find the last update date, time and user of the file field peoplecode

  How to find the last updated date time fields of peoplecode records?
  
  Thank you.

  We can check the update date-time using the following query

  SELECT LASTUPDDTTM IN THE PSPCMPROG WHERE OBJECTVALUE1 LIKE "RECNAME" AND OBJECTVALUE2 AS "FIELDNAME".

• How to find the status of the package (valid/invalid) was at one time

  How to find the status of the package (valid/invalid) was at one time?
  I want to find the status of an oracle package to 15:00 yesterday. Today, the status of this package is INVALID.
  I'm sure it was VALID yesterday. But no way to prove it. Can any one help please?
  I can generate AWR report for the last 7 days...

  Try to use a flashback, like this query:

  select object_name, object_type, status
  from dba_objects AS OF TIMESTAMP (SYSTIMESTAMP - INTERVAL '18' HOUR)  -- 18 hours ago
  where object_name = 'MY_OBJECT'
  ;
  

  If you have not granted privs FLASHBACK, you may connect as SYS to make a request flashback on a table data dictionary.
  But this should give you the info you need - if it's still in cancellation.

• How to find the velocity of an incremental encoder

  I use the RE22I encoder which can give up to 8192 pulses per revolution, I have A, B, Z reports that I use an fpga as a controller Please help me.

  How to find the speed of the encoder using these signals I'm going to have a clock in the fpga sysytem will help.

  Start by looking at the information on Wikipedia on the rotary encoders and a book on encoders OR white.  These articles will give you a basic understanding of the encoder and the signals it produces.

  With proper decoding, you can get the direction and momentum of each of the points on your encoder 8192.  If the tree can reverse (same vibration on one point unique all-in-mnearly stationary), full decoding must be used.  If data are only of interest while the tree turns in a direction and speed will not close to zero, a simple decoding can be used.  Decoding of a quadrature encoder is a good way to learn to use a state machine.  Signals A and B can exist in only four possible combinations, but the possible transitions to do interesting things.

  Define DECODING is a purely logical exercise and it is a simple coding in LabVIEW, such as a state machine.  There are examples, Desing Patterns, or project templates (depending on your version of LV) that come with LV to help you get started.

  By using the channels A and B you can update your calculation of velocity 8192 times per turn.  With the help of Z you get only an update by the revolution. You use depends on your application.  The pulse of Z is also useful to define a reference position for the measurement of phase angle.

  Lynn

• How to find the number of data items in a file written with the ArryToFile function?

  I wrote a table of number in 2 groups of columns in a file using LabWindows/CVI ArrayToFile... Now, if I want to read the file with the FileToArray function so how do I know the number of items in the file. during the time of writing, I know how many elements array to write. But assume that I want the file to be read at a later time, then how to find the number of items in the file, so that I can read the exact number and present it. Thank you all

  Hello

  I start with the second question:

  bytes_read = ReadLine (file_handle, line_buffer, maximum_bytes);

  the second argument is the buffer to store the characters read, so it's an array of characters; It must be large enough to hold maximum_bytes the value NULL, if char [maximum_butes + 1]

  So, obviously the number of lines in your text tiles can be determined in a loop:

  Open the file

  lines = 0;

  While (ReadLine () > 0)

  {

  lines ++;

  }

  Close the file

• How to find the position of the VI icon currently run on the block diagram of the appellant

  Dear forum,

  I am currently trying to use a LabVIEV VI as a simple sequencer: several (very slow) actions must run one after the other. Each action is represented by a Sub - VI, some actions are executed several times. My task is to view the Subvi somehow executing.

  My first intention (just manipulate the icon of the VI running with 'Icon.Get VI as Image data' / 'Icon.Set VI of Image data' invoke nodes) has failed, because it changes all instances of the VI icon. If you use the same VI several times, all these VI icons are changed (see here: http://forums.ni.com/t5/LabVIEW/How-to-change-animate-icon-of-currently-running-VI/m-p/3120754/highl... )

  My current approach is to use an image of the block diagram (with "VI: block diagram: get resized Image ' call method) in a picture of the front panel control and working within this control. But for this I need to know the position of the icon of the VI running. I know that I can assess the limits and Position via the properties GObj, but how to find the VI running (note that a VI can be installed several times on the block diagram, so the name of the VI is not unique)? IMHO the easiest way might be if a VI might find its icon on the block of the appellant diagram itself when it is run...

  It is clear that this position is not yet the position on the photo, but this conversion is a small piece of work...

  Kind regards

  cpschnuffel

  
  

• How to find the password for my Motorola Wireless?

  How to find the password for my Motorola Wireless?

  How to connect another computer to the Motorola Wireless?

  ... and now my computer won't connect to the wireless...

  Now would be a good time to use the instructions of the Setup Guide quick Motorola SBG940.

  ... I think I'll call my cable provider then!

  It may be better to talk to someone on the phone instead of trying to communicate via typed messages repeated as some of the information in the previous messages typed always seem to be lost in translation.

• How to end the system idle process

  How to end the system idle process
  ... "it is to consume my whole CPU.

  system:
  HP pavilion g4 series
  Intel core i5

  No it's not! Maybe someone else can give a better explanation, but the way I understand it is that when your system is idle, the system shows 100% idle process or nearby and it is because it has no applications or programs that run, but as soon as you open a program or run an application, and it requires CPU resources say between 1 and 4%, you will see the system idle drop in numbers, which shows the amount of the resources required by the program or open application.

  So I believe that everything that is, show processor resources available to a given point in time.

  Now, a virus can attack the process and change his behavior? I don't know, but if you suspect a malware attack, run complete scans of your system just to be sure.

  Good luck.

• How to find the size of the virtual server?

  Hello

  We intend to pass our applications 4 virtual servers has 2 physical servers. In this process, we need to identify the size of the current virtual servers to use as a starting point to configure or add the size in physical server. can anyone provide information on whats stats to be noticed and how to find the size of the current virtual servers?

  Thank you

  Hi Sekhar, there.

  in general, it is a fairly complex task if you want to size the new platform correctly, i.e. not to oversize it and have very low use below, i.e. spend too much on equipment.

  In fact, it's the first thing to consider the level of use of the new platform. Most likely your organization (HW and infrastructure) has targets to a minimum. optimal and maximum usage levels.

  In the case where you do not have this as a starting point, and then you continue with load average and the current peak (CPU, RAM, NW). To these basic lines, you can use the statistics of WLS Admin Console, where the use of CPU and memory statistics are presented since the server was last started. For more detailed statistics, you can use WLDF to capture measures key at regular intervals, and then base your analysis of these data.

  Finally and above all, the size of FS, but I've seen some comments above related to the size of the FS.

  HTH,

  A.

• How to find the url of adf application that has been deployed to the glassfish Server? I try but? It is the image of the page.

  Mr President

  This is the page of the glassfish Server

  

  How to find the url of adf application that has been deployed to the glassfish Server? I try but? It is the image of the page.

  

  In the jdev web module are

  [11: 09:38] wrote the Web for F:\backup of AshCMS\AshCMS\ViewController\deploy\AshCMS_ViewController_webapp.war application Module

  [11: 10:33] wrote the Module Enterprise Application to F:\backup of AshCMS\AshCMS\deploy\AshCMS_Project1_AshCMS.ear

  [11: 10:33] Application deployment...

  [11: 14:24] Application deployed successfully.

  [11: 14:24] time to deployment: 8 minutes, 11 seconds

  [11: 14:24]-deployment is complete.  ----

  what url in the browser.

  Concerning

  Mr President.

  I run my application on built-in web logic server and get the url from there

  http://localhost:7101 / ViewController/faces/MainPage

  then simply change the localhost of 7101 to 8081 as below

  http://localhost: 8081, ViewController, faces, MainPage

  and it works

  Concerning