How to find the time to what zero crossing point occur using zero crossing vi

Similar Questions

• How to find the time to process a request?

  IM using oracle express edition, can someone help me, how to find the time to process a request?

  Trace queries and tkprof the trace file generated.
  http://download.Oracle.com/docs/CD/E11882_01/server.112/e16638/SQLTrace.htm#PFGRF01010

• How to find the time between two channels of entry in the data acquisition card or pci 6036

  Hello

  I read a lot-related posts on the simultaneous measurement of two input voltage of similar channels in map data acquisition. I know that the best material is "simultaneous measurments of the Series DAQ cards" but I only pci data acquisition card 6036 and I try to understand what is the time between the reading of the two channels . This period is always constant? (must it rely on a voltage (amplitude, frequency, waveform..). I send the sine wave (s) to the two channels and read the values of V, if they read the same value, the difference should always be zero but I get-0,002 to 0.002 Volt difference (I must find a way to convert it in time). A screenshot of my VI is attached. I wonder how I can accurately measure the time delay between the channel.

  I am open to any suggestion, my final goal to read exactly two channels at the same time ((ou connaître le délai exact donc je peux correspondre les données correspondantes étant donné le temps de retard))

  Hi spinup,

  better you should post your question in the forum of LabVIEW, LabWindows/CVI is used

  Good luck.

• How to find the IP address assigned to Dev Alpha for use with blackberry-deploy?

  The Playbook, I use blackberry - deploy to install the .bar file. It requires the IP address assigned to the Playbook, which is available by clicking on an icon in the status bar in development mode.

  However, I don't see such an icon on the alpha of dev. Is it possible to find the IP address assigned to Alpha of Dev that I can use with blackberry-deploy?

  Answered my own question. Its network connects-> advanced-> Internet connection.

• How to find the type of Web server is configured for use with ColdFusion

  Hello

  Where can I check to see what kind of server that ColdFusion is configured to run currently? I have an existing CF installation 9.0.1, which I'll be removing and installing CF 9.0.2. During the instalation of the 9.0.2 version I would need to specify the server to use - Server ColdFusion / Apache / IIS etc. My question is, where I see in CF 9.0.1 existing to understand the server that is currently being used.

  Thank you!

  You can use the Web Server Configuration tool. Assuming you are on Windows, the path to start is generally

  Start-online programs-online Adobe-ColdFusion 9 online-online Configuratiol tool for the Web server

  In fact, you can use this tool to add or remove web servers.

• Find the time displaced table

  Hi all
  
  I'm in oracle 10 g 2. I have a table being stripped of some process. We have several tasks scheduled for every night.
  
  Is it possible to find the time of what a table is dropped, just to make a guess what regular process could be the culprit?
  
  Enjoy your suggessions
  
  Thanks in advance
  
  NU

  select object_name,original_name,droptime
  from recyclebin
  

  If recyclebin is enabled
  So you can be insterested to configure auditing

  Best regards

  Maxim

• says that there is an update of firmware available for my 3 t time capsule. I get "an error occurred when downloading". How to find the problem?

  I said that there is an update of the firmware available for my 3 t time capsule. I get the message "an error occurred when downloading". How to find the problem? I have elcapitan 10.11.6 and capsule version 7.7.3

  Try temporarily, connect your MacBook Pro to your Time Capsule using an Ethernet connection... If not already, then try downloading the firmware again.

• What is the last level of patch bundle for x 3-2 exadata machine? How to find the doc?

  We have a x 3-2 exadata machine. I have a question: what is the last level of patch bundle for x 3-2 exadata machine? How to find the doc?

  Thanks in advance.

  Check note id 888828.1

  It has all the information you need.

• How to reset the timer to zero?

  Good day people,

  How to reset the timer to zero?

  I have a button in the timeline relative to the code below, and when I click on it I want to the behavior of the time back to 1 or 0.

  Click the timer to 1 or 0.

  -----------------------------------

  contents_mc - timer_txt

  -----------------------------------

  _root.elapseTime = 0;

  intervalId = setInterval (this, "countDown", 1000);

  function countDown() {}

  {if (_root.timerOn)}

  ++ _root.elapseTime;

  " _root.elapseTime = _time +" "seconds";

  if(_root.elapseTime == 10) {}

  _parent.gotoAndStop ("GameOutOfTime");

  clearInterval (intervalId);

  }

  }

  }

  Stop();

  Any response will be appreciated,

  Thank you

  use:

  function resetF (): Void {}

  clearInterval (intervalID);

  intervalId = setInterval (countDown, 1000);

  }

• How to find the last update date, time and user of the file field peoplecode

  How to find the last updated date time fields of peoplecode records?
  
  Thank you.

  We can check the update date-time using the following query

  SELECT LASTUPDDTTM IN THE PSPCMPROG WHERE OBJECTVALUE1 LIKE "RECNAME" AND OBJECTVALUE2 AS "FIELDNAME".

• How to find the status of the package (valid/invalid) was at one time

  How to find the status of the package (valid/invalid) was at one time?
  I want to find the status of an oracle package to 15:00 yesterday. Today, the status of this package is INVALID.
  I'm sure it was VALID yesterday. But no way to prove it. Can any one help please?
  I can generate AWR report for the last 7 days...

  Try to use a flashback, like this query:

  select object_name, object_type, status
  from dba_objects AS OF TIMESTAMP (SYSTIMESTAMP - INTERVAL '18' HOUR)  -- 18 hours ago
  where object_name = 'MY_OBJECT'
  ;
  

  If you have not granted privs FLASHBACK, you may connect as SYS to make a request flashback on a table data dictionary.
  But this should give you the info you need - if it's still in cancellation.

• How to find the velocity of an incremental encoder

  I use the RE22I encoder which can give up to 8192 pulses per revolution, I have A, B, Z reports that I use an fpga as a controller Please help me.

  How to find the speed of the encoder using these signals I'm going to have a clock in the fpga sysytem will help.

  Start by looking at the information on Wikipedia on the rotary encoders and a book on encoders OR white.  These articles will give you a basic understanding of the encoder and the signals it produces.

  With proper decoding, you can get the direction and momentum of each of the points on your encoder 8192.  If the tree can reverse (same vibration on one point unique all-in-mnearly stationary), full decoding must be used.  If data are only of interest while the tree turns in a direction and speed will not close to zero, a simple decoding can be used.  Decoding of a quadrature encoder is a good way to learn to use a state machine.  Signals A and B can exist in only four possible combinations, but the possible transitions to do interesting things.

  Define DECODING is a purely logical exercise and it is a simple coding in LabVIEW, such as a state machine.  There are examples, Desing Patterns, or project templates (depending on your version of LV) that come with LV to help you get started.

  By using the channels A and B you can update your calculation of velocity 8192 times per turn.  With the help of Z you get only an update by the revolution. You use depends on your application.  The pulse of Z is also useful to define a reference position for the measurement of phase angle.

  Lynn

• How to find the url of adf application that has been deployed to the glassfish Server? I try but? It is the image of the page.

  Mr President

  This is the page of the glassfish Server

  

  How to find the url of adf application that has been deployed to the glassfish Server? I try but? It is the image of the page.

  

  In the jdev web module are

  [11: 09:38] wrote the Web for F:\backup of AshCMS\AshCMS\ViewController\deploy\AshCMS_ViewController_webapp.war application Module

  [11: 10:33] wrote the Module Enterprise Application to F:\backup of AshCMS\AshCMS\deploy\AshCMS_Project1_AshCMS.ear

  [11: 10:33] Application deployment...

  [11: 14:24] Application deployed successfully.

  [11: 14:24] time to deployment: 8 minutes, 11 seconds

  [11: 14:24]-deployment is complete.  ----

  what url in the browser.

  Concerning

  Mr President.

  I run my application on built-in web logic server and get the url from there

  http://localhost:7101 / ViewController/faces/MainPage

  then simply change the localhost of 7101 to 8081 as below

  http://localhost: 8081, ViewController, faces, MainPage

  and it works

  Concerning

• How to find the last pasted paragraphs FMP?

  I'm sticking FMP several objects at once in a file (a file of changes to the sections containing the changebars) in the main text flow. I want a separator line to go at the end of each pasted section, so I try to insert one after the paste operation. But instead of a line between each section, all lines are added at the end of the file, after all the sections. So if there are 3 glued sections at the end of the file are three lines. My code is below, do you know how I could fix this?

  Thank you, Mark

  function copyPasteChanges (doc, chgRange) {}

  Select the section with changebar and copy it.

  doc. TextSelection = chgRange;

  doc. Copy();

  Prepare for the changes doc and paste there the modified section.

  var firstChgPgf = changesDoc.MainFlowInDoc.FirstTextFrameInFlow.LastPgf;

  var changesTloc = new TextLoc (firstChgPgf, Constants.FV_OBJ_END_OFFSET);

  var changesTRange = new TextRange (changesTloc, changesTloc);

  changesDoc.TextSelection = changesTRange;

  changesDoc.Paste ();

  To go at the end of the file again (I think)

  var lastPgf = changesDoc.MainFlowInDoc.FirstTextFrameInFlow.LastPgf;

  var dividerPgf = changesDoc.NewSeriesPgf (lastPgf);

  var TLoc = new TextLoc (dividerPgf, 0);

  changesDoc.AddText (TLoc, '_');

  }

  Hi Mark,

  The problem is that the dough does not occur when you think. The dividing line is added at the end of the file, but are not your actions of dough. Actually, I think that maybe a little random where pasta is produced, because this line:

  var changesTloc = new TextLoc (firstChgPgf, Constants.FV_OBJ_END_OFFSET);

  .. .is does not create a valid text location. You can check this by abandoning the service after:

  changesDoc.TextSelection = changesTRange;

  .. and look at where's the insertion point. It will probably be everywhere where you left it last, because the call is not valid. I can't tell you exactly why, except that it has something to do with the fact that you are using the last paragraph in the stream. There is something weird to try to define a range of full-paragraph text with the last paragraph. I'm sure it's related to how the last TFP in a stream does not show a mark of FMP, but beyond that, I don't know how to do what you're trying to do with the last paragraph.

  Having no knowledge of how do it right, any time I need to do this, I create a paragraph "dummy" at the end of the flow to fill that space strange 'last FMP", then do the work around it. In the end, I just want to remove fake TFP. I don't know if it's a good idea or not, but it's the only way I ever get it to work and it sorts the mirror how you could do this manually in the GUI.

  With this, I modified your script as follows, and it seems to work better. Note that I also modified the logic of how to find the last paragraph of the flow by writing a separate function. Your call to the 'FirstTextFrameInFlow' is OK, unless your doc begins to span several pages and/or begins with several empty pages. The function I wrote ensures that you really the last TFP in the stream.

  I hope this helps.

  Russ

  function copyPasteChanges (doc, chgRange) {}

  Select the section with changebar and copy it.

  doc. TextSelection = chgRange;

  doc. Copy();

  Prepare for the changes doc and paste there the modified section.

  var lastPgf = getLastPgf (changesDoc);

  var dummyPgf = changesDoc.NewSeriesPgf (lastPgf);

  var changesTloc = new TextLoc (dummyPgf, 0);

  var changesTRange = new TextRange (changesTloc, changesTloc);

  changesDoc.TextSelection = changesTRange;

  changesDoc.Paste ();

  To go at the end of the file again (I think)

  Don't forget that last TFP is now fake TFP

  lastPgf = getLastPgf (changesDoc);

  var dividerPgf = changesDoc.NewSeriesPgf (lastPgf.PrevPgfInFlow);

  var TLoc = new TextLoc (dividerPgf, 0);

  changesDoc.AddText (TLoc, '_');

  dummyPgf.Delete ();

  }

  function getLastPgf (doc)

  {

  textFrame var is doc. MainFlowInDoc.LastTextFrameInFlow;

  var lastPgf = textFrame.LastPgf;

  While (! lastPgf.ObjectValid () & textFrame.ObjectValid ())

  {

  textFrame = textFrame.PrevTextFrameInFlow;

  lastPgf = textFrame.LastPgf;

  }

  Return lastPgf;

  }

• NB200 - how to find the 3G module for it?

  Hello

  Pls how I find the 3G module in my NB200 - PLL20E?

  Thank you

  Hello

  What do you mean exactly?
  You want to upgrade your NB200 with a card 3G?

  If yes then you must make sure that your NB200 could be improved using this card.
  I'm not sure if this is possible.

  But don t give up boyfriend Toshiba authorized service partner in your country could provide details.
  Guys might be able to tell if this is possible and could provide a good 3G module

  If you get more details please share with us!

  See you soon