How to increase the sampling rate in this VI?

Hi all

I have recently inherited this mess of a VI and can not figure out how to increase the sampling rate. I tried to change the "ms of waiting ' clock, but it does not add more data points." The main VI, as well as the Subvi, which contains a Daq Assistant to a load cell and LVDT is attached. Any ideas on how to improve the sampling without a complete overhaul would be greatly appreciated!

Thanks in advance!

If you are grateful, feel free to give congratulations and mark the topic as resolved.

Tags: NI Software

Similar Questions

  • If I use a few channels on PCI-6259 to increase the sampling rate, channels numbers can I be contiguous?

    We are looking to buy a card PCI-6259 usable on a Linux machine. We would use NIDAQmx to access the card. If we were to use only a few channels to increase the sampling rate, do I need to select specific channels?

    For example, the card is 1 MHz. If I select the channel 1 and channel 2, I can taste each channel at 500 KHz. could I choose 8 channel and channel 13 and still be able to sample each channel to 500KHz? Or need of specific channels to use when a subset of channels are selected?

    Thank you

    -Tom

    Thanks for the quick response.

    -Tom

  • How to improve the sampling rates high in samples mega 3rd spartan Board

    I am trying to acquire data in spartan 3rd Council mega samples rate can you post me examples to this effect

    So far, I've got to get the frequency in Kilosamples of sampling, but megasamples requires complex code

  • DMM (NI 4070), how to correctly set AC Freq (bandwidth) by the sampling rate

    using a NI4070 multimeter and I see the max connection is 300 kHz by respect it.  But I don't understand how to set the min and max, acFrequency according to the sampling frequency or speed reading.

    6 1/2 digits resolution, the speed can vary from 0.25 s/s to 100 s/s and this range corresponds to a lower end on the connection (minimum acFreq) from 1 Hz to 400 Hz.

    (Q1a) - is the playback speed, controlled by the minimum setting of IviDmm_ConfigureACBandwidth?   or vice versa?

    Otherwise, I do not see how to control the rate of reading or the sampling frequency.   IviDmm_ConfigureMeasurement only allows you to control the range and resolution.

    (Q1b) - is there a way to directly control the sample rate (digitizer) or playback speed (dmm)?

    (T2) - the upper limit of the bandwidth of AC always seems to be at 300 kHz... is there still a reason to reduce this maximum value?

    (T3) - Finally, unlike the traditional niDmm function, the resolution via the IVI configuration should be passed as absolute value; does directly when number of digits and the beach?   For example if I want to 6 1/2 digit to 300V range, I guess that by the specifications that the resolution should be set at 0.001 V... followign, if I want 5 1/2 digits to 1V range, the resolution should be set to 0.00001 V?

    Hi Rjohnson,

    I'll try to answer your questions as best as I can:

    Q1A.  The ConfigurACBandwidth function is used by the driver OR DMM to calculate the good aperautre for the measure.  So yes, by adjusting your minimum frequency, you will affect your reading speed.

    Q1B.  Your reading rate will depend largely on your measuring cycle.  To get a fast measuring cycle, there are a few things that you can adjust.  You can programmatically control your time aperature, as well as your time to settle.

    Q2. I can't find a reason to change. This parameter is only used for error-checking and verifies that the value of
    This setting is less than the maximum frequency of the device.

    Q2B.  I think what you say is right, but I'll need to check on that - I'll let know you as soon as.

    Hope that helps.  "" "I would recommend checking the explanation of the Cycle of the DMM measurement in DMM help' devices ' NI 4070" DMM Measuments "DMM measurement Cycle.

    Take care!!

  • How to increase the rate on windows vista

    my rate to refreash on windows vista needs to increase... looked at solutions and it seems that vista is no longar supported by microsoft can anyone help

    Hello

    Why are you trying to increase the refresh rate? What exactly is the problem?

    You can see the steps in the following article on how to change the refresh rate.

    Flicker of the correct monitor (refresh rate).

    http://Windows.Microsoft.com/en-us/Windows-Vista/correct-monitor-flicker-refresh-rate

  • How to increase the font size to the bridge using windows 7 and a k 4 monitor?  It seems that this problem has come up before, but there is no answer.

    How to increase the font size to the bridge using windows 7 and a k 4 monitor?  It seems that this problem has come up before, but there is no answer.

    For Windows, you can try this:

    Adobe App scaling on the screens to high-resolution (FIX) | Dan Antonielli

  • How to set the sampling interval using DAQ hardware?

    Now I have a sensor capability and hardware DAQ 24 bit (http://www.mccdaq.com/usb-data-acquisition/USB-2404-10.aspx).

    The DAQ hardware has the 50kS/s maximum sampling rate. My question is how to define the range of data collection. For example, if I set the sampling rate of 2000, continuous sample mode, I use read.vi DAQmx in a while loop and set the "number of samples per channel" to 100. I want to plot these data over time using a XY Chart and also save this data. So I add a 'Medium' function to get the average of 100 samples per each loop (medium, there are 20 release of data per second). But when I put a 'number of samples per channel' much more small (for more data per second), there are a few problems. It seems that the program cannot read the data as much and get the average at a higher frequency. I don't know where is the problem. Overall, the collection of data more frequently? Maybe I didn't articulate my question. I'll upload a simple program later if necessary. Thank you.


  • How to increase the size of the menu bar?

    My bar menu and all the buttons at the top suddenly, all are much smaller. Any ideas on how to increase the size of the top of the screen? IM talking not about the size of Web pages, just the menus up to the top.

    Don't want to use the menu bar and not the Firefox menu button?

    See also:

    You had previously placed all the items in the Menu bar?

    You can set the layout.css.devPixelsPerPx pref on the topic: config page on 1.0 or Windows 8 to 1.25 and if necessary adjust layout.css.devPixelsPerPx from 1.0 to 0.1 or 0.05 steps (1.1 or 0.9) do the icons to display properly.

    See also:

    An extension allows you to adjust the size of the text in the user interface and zoom the page in the browser window.

    You can watch this extension to adjust the font size for the UI (toolbar).

    You can watch the Default FullZoom Level or NoScript extension if the web pages need to be adjusted after the change of layout.css.devPixelsPerPx.

  • Increase the refresh rate of my LCD

    Hey Hey Hey. How to increase the available for my LCD refresh rate? Should I increase the refresh rate? I can't find where to change.

    The screen flashes? What is the refresh RRSP now? If you have set to 60 hz, it's ok.

  • How to increase the video memory on my Satellite 1800-254?

    A friend give me a Toshiba satellite 1800 Lalonde - 254 s for use only watch movies for my kids. With graphics memory, it has its impossible to reproduce movies, so I increased the RAM to 512 MB graphics memory is 8 MB. How I increase the graphics memory? Is it possible?

    Thank you very much

    Titanico

    (Excuse my English, I use a translator)

    This old laptop has a graphics card with shared memory. In other words, when you have more RAM inside more memory will be used for graphical operations. According to the specifications of the laptop this old notebook was shipped with 128 MB of RAM, but can be improved up to 512 MB.

    Trying to find internet modules two PC100 256 MB with part number PA3069U - 1. 25 M and update.
    That's all what you can do about it.

  • determination of the sampling rate and the frequency waveform data record

    Hello

    I write a simple program that collect data from a triaxial accelerometer input, convert it to a frequency spectrum, and then save the time domain and the frequency of the waveforms in an external file separated.  I don't understand how to set the sampling frequency, however.  On the DAQ Assistant, I updated the acquisition mode "Samples continues" and read samples is 2 k, which corresponds to the total number of data points that are collected.  How can I program sampling for awhile, it 30 seconds, for example?  Wouldn't be better to set up a trigger, as it will continue to collect data up to what I told it to stop?

    I also want to save waveform data in a separate file that can be easily seen by other computers that have not installed Labview.  I have currently the program put in place to convert a text string of the waveform of the time domain and then save it in a text file or a spreadsheet.  It works fine, but I would also like to record the frequency wave, which is a different type of data.  How can I do this or is there a better way?

    My program is attached.  Thanks for your help!

    Here's how you can use the shift register to build the table, and also where you can choose to play exactly 100 samples per while the loop iteration.

    Brian

  • The FONT SIZE is too small in Hotmail Live email. Please indicate how to increase the font size

    The FONT SIZE in Hotmail Live is too small. Please indicate how to increase the font size

    Thank you.

    This isn't. You have ra reolution of 800 x 600 or less?

    Try this

    In Internet Explorer don't see--> text size--> medium/large.

    or increase your zoom level (IE 7/8)

    or try a combo of the two

    Maryse Agarwal

  • How to increase the speed of the PC without adding RAM

    PLEASE HOW CAN INCREASE THE SPEED TO RUN THE PC WITHOUT ADDING MORE RAM

    Some reasons for the slow pace of the computer:

    1. computer has not been maintained - http://www.elephantboycomputers.com/page2.html#Maintenance

    2. the computer is infected with the malware - http://www.elephantboycomputers.com/page2.html#Removing_Malware

    3. the disk is too full. Remove useless stuff, uninstall unused programs. Do not forget to save!
    http://www.elephantboycomputers.com/page2.html#Backing_Up

    4. flaky third party software. Toolbars and modules are particularly guilty in this area. Uninstall toolbars (Google, Yahoo, ISP brand, etc) and look at what modules are in use in your browser (s).

    5. computer has too many unnecessary programs/processes running in the background. Manage your Startup:

    For XP - How to troubleshoot using the Msconfig in Windows XP utility - http://support.microsoft.com/?id=310560
    The free Autoruns program is very useful for managing your Startup - http://www.microsoft.com/technet/sysinternals/default.mspx

    For Vista/Windows7 - Start Orb > Search box > type: msconfig and when it appears in the results area above, right-click and choose 'run as administrator '. Autoruns is also very useful.

    6. the user runs an inflated/invasive such as Norton and McAfee antivirus program. Replace it with a better program. I recommend NOD32 (commercial) or Avast (free). Avira is also good, but the free version has an unpleasant reminder screen (Google for instructions on how to disable it). The user can also run several real-time antivirus/firewall/security programs.

    7. the user has installed new programs that are processor and/or memory-intensive (Photoshop, AutoCAD, Mathmatica or similar) and does not have the power of the equipment.

    8 drive fails and is in PIO Mode. It's very much slow (like being in 1985). See Hans-Georg Michna here information - http://winhlp.com/?q=node/10

    In addition to the above, see also http://miekiemoes.blogspot.com/2008/02/help-my-computer-is-slow.html

    Note: If the computer has always been slow, in addition to the above user may have bought a machine with a less powerful processor and not enough RAM (memory). The normal use of the computer, 512 MB to 1 GB is sufficient for XP; Vista should have a minimum of 2 GB; Windows 7 is less demanding than Vista, but the minimum of 2 GB should also be used. MS - MVP - Elephant Boy computers - don't panic!

  • How to increase the application version number in the eclipse runtime Android plugin

    I use BlackBerry Android plugin eclipse runtime to code sign my application. She is successful the first time, later I changed some code and code sign again and error

    Error: Code signing request failed because this file was previously signed.    .bar //dist/Android 2.3.1 ------.bar BlackBerry previously signed

    Then, I read a few post on this forum and find a version in .xml number must be increased to fix my mistake, but I can't find such a file and the version number in the eclipse project. He would be grateful if someone can tell me how to increase the version number in a project created by BlackBerry Android plugin eclipse runtime.

    You must edit the AndroidManifest.xml file you will find in the root of the project in Eclipse.

    Just increase the parameter 1 versionCode.

    http://developer.Android.com/Guide/publishing/versioning.html

  • I would like to know how to get a debugger and how to increase the memory on my computer of mocarosoft 7 HP

    I tried to find information on the question of the debugger, but I'm at a total loss about how to increase the memory of the computer.  Please help me, because I have school work on this 'thing'.

    The Windows debugger is included in the SDK

    http://www.Microsoft.com/en-US/Download/details.aspx?displaylang=en&ID=8279

    http://msdn.Microsoft.com/en-us/Windows/hardware/gg463009.aspx

Maybe you are looking for