How to install and activate Windows XP after the upgradation of hardware

Similar Questions

• Install and activate Windows by using the OEM product key

  I had some issues with UEFI on my system and went to a local store because there is no support for acer in my country and the guy local flash my bios to a version not uefi-uefi. I read in an article that the product key of my windows preinstalled has been in the bios. I used some how a VB script that I found on a Web site for my product which is activated key. (1) can I still use this product key? I run the recovery disk utility and made a usb key as well as the recovery partition recovery. (2) can I use the product key with the usb of recovery in the case where my left hard drive system are also formatted?

  Original title: product key

  Why the BIOS was flashed to an older version?

  There is no WIndows 7 OEM embedded product key so I don't know what that means.  I asked you to run two programs to compare the key OEM of Windows 8 - reported BIOS.  We aren't interested here in another key said except OEM BIOS.  They match?  If none is reported, then it was erased with the BIOS flash.

  You can contact the technical support from the manufacturer to ask how to recover your key.

  I don't think it will reactivate without the key included if you reinstall.

  However when he is currently enabled so what I would do is follow Clean install Windows 10 Upgrade

  in order to ensure the free update now before its expiration July 31, then you will have permanent right to the PC for Windows 10 in Activation of MS servers outside any key of WIndows 8.

  First, you can do the installation to another partition, that you reduce c in Disk Mgmt, as long as you start the media during installation to select the new partition, then look after installation to see if it is active Windows 8 on the drive and if so feel safe remove Windows 8 when it is ready (or not).  Until then, use the Dual Boot menu at startup to choose.

  That's what I would do in your place and the sooner the better.   If the built-in product key was wiped out during the BIOS flash and technical support from the manufacturer won't help you, your best bet is to secure free Windows 10 Upgrade for the rest of the life of the PC.  The link provides the best install and has not reported complaints in total tens of thousands of people have used it.

• Command prompt to activate Windows 10 after the upgrade to Windows 7

  Separated from this thread.

  I'm having a similar problem, from 7 to 10.

  Recently, I buy a pc refurbishment that came from a "Microsoft authorized repairer" and gave me a "genuine windows 7 product key" I have tried to upgrade to windows 10 after having done all windows 7 updates. After download and prepare the 10 updated windows a message appears saying that windows is not active on my computer and I need a product key windows 10.

  I took the advice of your recent post and made the diagnosis. Here are the results:

  Diagnostic report (1.9.0027.0):
  -----------------------------------------
  Validation of Windows data-->

  Validation code: 0
  Code of Validation caching online: 0x0
  Windows product key: *-* - VKCWD - Q32Q4-44M7D
  Windows Product Key hash: HiBDDPXFLL3M/1vsxbINZbyKZZA =
  Windows product ID: 00359-OEM-8683287-87521
  Windows Product ID Type: 3
  Windows license Type: OEM System Builder
  The Windows OS version: 6.1.7601.2.00010300.1.0.003
  ID: {6B96B72D-9625-4B84-A93D-7CF97E697197} (1)
  Admin: Yes
  TestCab: 0x0
  LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Product name: Windows 7 Home Premium
  Architecture: 0 x 00000009
  Build lab: 7601.win7sp1_gdr.151230 - 0600
  TTS error:
  Validation of diagnosis:
  Resolution state: n/a

  Given Vista WgaER-->
  ThreatID (s): n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002

  Windows XP Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  File: No.
  Version: N/a, hr = 0 x 80070002
  WgaTray.exe signed by: n/a, hr = 0 x 80070002
  WgaLogon.dll signed by: n/a, hr = 0 x 80070002

  OGA Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002
  OGAExec.exe signed by: n/a, hr = 0 x 80070002
  OGAAddin.dll signed by: n/a, hr = 0 x 80070002

  OGA data-->
  Office status: 109 n/a
  OGA Version: N/a, 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

  Data browser-->
  Proxy settings: N/A
  User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
  Default browser: C:\Program Files (x86)\Google\Chrome\Application\chrome.exe
  Download signed ActiveX controls: fast
  Download unsigned ActiveX controls: disabled
  Run ActiveX controls and plug-ins: allowed
  Initialize and script ActiveX controls not marked as safe: disabled
  Allow the Internet Explorer Webbrowser control scripts: disabled
  Active scripting: allowed
  Recognized ActiveX controls safe for scripting: allowed

  Analysis of file data-->

  Other data-->
  Office details: {6B96B72D-9625-4B84-A93D-7CF97E697197}1.9.0027.06.1.7601.2.00010300.1.0.003x 64*-*-*-*-44M7D00359-OEM-8683287-875213S-1-5-21-2170102926-742898452-2244735825Hewlett-PackardHP EliteBook 8440pHewlett-Packard68CCU worm. F.1120101125000000.000000 + 000B02C3207018400FC04090409Time(GMT-08:00) Standard Pacific03HPQOEMSLIC-MPC109

  Content Spsys.log: 0 x 80070002

  License data-->
  The software licensing service version: 6.1.7601.17514

  Name: Windows 7 HomePremium edition
  Description: operating system Windows - Windows (r) 7, channel OEM_COA_NSLP
  Activation ID: 9ab82e0c-ffc9-4107-baa1-c65a8bd3ccc3
  ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f
  Extended PID: 00359-00172-832-887521-02-1033-7601.0000-0322016
  Installation ID: 018105957480667511420195183284070412547006053251816702
  Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=88338
  The machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=88339
  Use license URL: http://go.microsoft.com/fwlink/?LinkID=88341
  Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=88340
  Partial product key: 44M7D
  License status: initial grace period
  Time remaining: 42780 minute () (29 day (s))
  Remaining Windows rearm count: 2
  Trust time: 02/02/2016-12:30:55 AM

  Windows Activation Technologies-->
  HrOffline: 0x00000000
  HrOnline: 0x00000000
  Beyond: 0 x 0000000000000000
  Event timestamp: 2:1:2016 21:07
  ActiveX: Registered, Version: 7.1.7600.16395
  The admin service: recorded, Version: 7.1.7600.16395
  Output beyond bitmask:

  --> HWID data
  Current HWID of Hash: MgAAAAEAAwABAAEAAAABAAAAAwABAAEA6GEWaHhAiIKuXloDfhcQ2hxKVuwwWyLkXF0 =

  Activation 1.0 data OEM-->
  N/A

  Activation 2.0 data OEM-->
  BIOS valid for OA 2.0: Yes
  Windows marker version: 0 x 20001
  OEMID and OEMTableID consistent: Yes
  BIOS information:
  ACPI Table name OEMID value OEMTableID value
  APIC HPQOEM 172 A
  FACP HPQOEM 172 HAS
  HPET HPQOEM 172 HAS
  MCFG HPQOEM 172 HAS
  TCPA HPQOEM 172 HAS
  SSDT HPQOEM SataAhci
  SSDT HPQOEM SataAhci
  SLIC SLIC-MPC HPQOEM
  SSDT HPQOEM SataAhci
  SSDT HPQOEM SataAhci
  SSDT HPQOEM SataAhci
  ASF! HPQOEM 172 HAS

  You must activate Windows 7 by using the product key provided by your repairman authorized Microsoft.

  Select Start, right-click computer, click Properties, select change product key (under Windows Activation) and enter the product key of 25 characters (from the COA sticker). Click Next to activate via the internet. Restart your computer.

• How to activate Windows 7 after the 30 day period?

  How can I activat windows 7 after the 30-day grace period?

  Type Activate in the Windows 7 search box and click on the Activate Windows icon that appears at the top of the Start Menu.  Then enter your genuine Windows 7 product key for the edition of Windows 7 you have installed.  If you do not have a genuine Windows 7 product key, you can buy one on the Microsoft Store. Carey Frisch

• My PC is dead, I can not turn on PS and LR, how to install and activate a copy on my new PC?

  My PC is dead, I can not turn on PS and LR, how to install and activate a copy on my new PC?

  Cloud license allows 2 activations http://www.adobe.com/legal/licenses-terms.html

  -Install on a 2nd computer http://forums.adobe.com/thread/1452292?tstart=0

  -https://helpx.adobe.com/creative-cloud/help/sign-in-out-activate-apps.html

  -Windows or Mac has no importance... 2 on the same operating system or 1 on each

  -Two activations on one account CAN NOT be used at the same time (to be noted in the link above of the license)

  Remove the license on a computer http://forums.adobe.com/thread/1442423?tstart=0 clouds can help

  -read http://helpx.adobe.com/x-productkb/policy-pricing/error-maxium-acitvation-exceeded.html

  -or https://helpx.adobe.com/x-productkb/policy-pricing/activate-deactivate-products.html

  Serial number and activation (no-Cloud) https://forums.adobe.com/thread/2041990 of support for a version of serial number

• How to install and run windows on my macbookair?

  How to install and run windows on my macbookair?

  Hello

  I suggest you to follow the links and check out them.

  http://www.Apple.com/support/Bootcamp/

  http://support.Apple.com/kb/HT3986

  http://support.Apple.com/kb/HT1899

  Boot Camp Installation & Setup Guide

  http://manuals.info.Apple.com/en/Boot_Camp_Install-Setup_10.6.PDF

• How to install and activate all my downloads for Adobe lightroom and cs6 design web premium

  How to install and activate all my downloads for Adobe lightroom and cs6 design web premium?

  Download and Installation Help-

  https://helpx.Adobe.com/download-install.html

• activate Windows xp after the expiry of the grace period of 30 days

  How to activate windows xp after the expiry of the grace period of 30 days, if the user does not have internet on PC? the user can get a new activation code on the microsoft site?

  "rajesh kur" wrote in message News: 6811c2fa-5fa2-4c2c-805f-2347c8e571c2...

  How to activate windows xp after the expiry of the grace period of 30 days, if the user does not have internet on PC? the user can get a new activation code on the microsoft site?

  Use phone Activation
   
  
  --

  Noel Paton | Nil Carborundum Illegitemi | CrashFixPC | The lazy three fingers

• How to update and activate Windows 8.1 Overview to 8.1 of Windows through Windows Store?

  Original title: STORE WINDOWS PROBLEM

  Hello

  I installed windows 8 version spotted in my samsung laptop. When I open the windows store, it shows that "THIS VERSION OF WINDOWS IS NOT taken in CHARGE or COMPATIBLE GET NEW VERSION OF WINDOWS"

  Then I went to the microsoft site and saw the free update to windows 8.1 which must be downloaded from the store.

  How to solve this problem.

  Note one thing: I have not activated will there be problems because of this.

  waiting for your response.

  Hi Suchitheknath,

  Thank you for using Windows 8.1 Overview. The preview is no longer available for download and usage license expires January 15, 2014. If you have not yet installed the final version of Windows 8.1 or 8.1 RT for Windows, you must do it now.

  If you still use Windows 8.1 Overview, you will see a notification to re - install Windows every time you connect. After January 15, 2014, your PC will restart every 2 hours also and you will lose all unsaved data.

  Overview of Windows 8.1 8.1 Windows Update

  You must activate Windows 8.1 to use wisely. For more information about activation, see the articles.

  Why can't I activate Windows?

  Get help with activation errors

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• How to activate Windows XP after the installation of repair when you cannot connect to Normal startup.

  I got XP Home SP2 OEM installed on an AMD machine and the power supply is dead.
  I have a P4, I prefer to use in any case, I moved the hard drives of the AMD machine to machine P4.  Of course, XP wouldn't boot.
  Without saving anything, I performed a repair installation (under the installer, not Recovery Console).
  Everything seemed ok, but eventually, I restarted XP and a message box informed me that I could not connect until I had activated XP.
  Unfortunately, I can not run the Activation Assistant because I can not connect.

  I found that I could start the computer Safe Mode / command prompt and could then start Windows Explorer from the command line.
  I followed some advice I found online: I extracted wpa.dbl drive OEM installation and copied in the folder Windows\System32 and rebooted.  Nothing apparently changed; "" I still couldn't log mode "normal".
  I restarted mode safe mode / command prompt, began to Windows Explorer and installed XP SP3.

  Now I can connect mode safe mode without network but cannot connect with networking.  Normal mode is not yet available.

  When I try to start 'normally', the saying that I need to activate before I can connect message.  If I say 'Yes' to 'Activate now?', the background of the desktop appears (my own shows JPG) - but that's all.  The mouse cursor is there, but I have found no way to access all the features after it.

  I need suggestions for possible patches that will avoid the need to reinstall completely.

  Here is the response of Fracture, it worked for me:

  http://social.Microsoft.com/forums/en-us/genuinewindowsxp/thread/ece30d55-d72d-4FF9-AFE8-a577f0f4564f

• How to install firefox on windows 7 after warning "this publishing house has been blocked.

  Here's the story back in case it helps... I have upgraded from windows 7 to windows 10, had many problems of performance with 10 windows and reinstalled windows 7. After the reinstallation, I tried again to download mozilla firefox and install the browser. When I try to run the installer for firefox I get a message that says: "this publishing house has been blocked to run the software on your machine." The only option is to click on 'OK '. It is impossible to ignore the security warning and proceed with the installation. I had no difficulty to install any other software (IE and Chrome included).
  I tried to start windows in safe mode, but I still get the same caveat. I have administrator privileges when running the installation program. I found other forums dealing with similar problems, but have not found a solution for my specific case yet. I've attached a screenshot of the security warning window, so you can see there is no way to move forward. If I click on the help link on windows, it's not going anywhere.

  Well, I had an "ah-ha" moment and the fix was very simple. Not sure why it escaped me that long, but you can right click on the Setup file, select 'Properties' and on the 'Général' tab, there is a button "Unblock" the file. Yet, after this step, I was not able to run the Setup program. For some unknown reason, my role as an administrator is all messed up, but it is a different matter. To ignore the warnings of the editor blocked after release of the program, you must run the Setup program from the command with administrator privileges prompt. GoTo START-> all programs-> Accessories... right click on "Command prompt" and click "Run as Administrator", click 'Yes' If you get warnings of user account control to run the program. Once the command prompt opens in a new window cd to the directory containing your fireforx installation file and run it. This fixed my issue.

• How to install and activate an older version of Lightroom 3?

  Hello

  For a year, I use Lightroom6. Before that, I got Lightroom 3 on my Mac.

  Now, I wanted to give my old LR3 my included nice serial number. But it cannot activate the LR3 serial number and I don't know how to disable the function.

  For my new LR6, I have a new serial number.

  Please where can I deactivate my old license for LR3. Thanks for assistance in the short

  Greetings

  
  

  Emil

  When you have a non-functional computer and cannot turn it off, click on the link below

  Serial number and activation support (no-Cloud) https://forums.adobe.com/thread/2041990 to adjust the number of activations

  IF it has Mac El Capitan read below

  CS6 and previous programs have not been tested and will not be updated to run on Mac El Capitan

  -which means you are trying to use CS6 and earlier at YOUR risk of having problems

  -You can get CS6 and previous programs to install and run, or you can not (some do, some don't)

  -Java https://helpx.adobe.com/dreamweaver/kb/dreamweaver-java-se-6-runtime.html can help

  Install CS5 on Mac 10.11 https://forums.adobe.com/thread/2003455 can help (also for others than CS5)

  -also a TEMPORARY security change https://forums.adobe.com/thread/2039319

  -http://mac-how-to.wonderhowto.com/how-to/open-third-party-apps-from-unidentified-developer s-mac-os-x-0158095 /

  -the guardian https://support.apple.com/en-au/HT202491

• Unable to activate Windows 7 after the repair of the equipment

  Recently, I received my motherboard fixed for a problem with the display. After the repair, my basic Windows 7 Home Edition is not be re-enabled. My product ID is 00346-OEM-8934407-80437. Help, please

  Have you tried to restart by phone?

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

• DeskJet 2546 b: Wireless print job stays in queue and poster printer offline after the upgrade to Windows 10

  I write a fix I found for a pretty annoying problem involving 10 Windows and HP wireless printers.

  My Deskjet 2546-b printer was printing OK wireless to the point 8.1 of Windows until that I upgraded my computer to Windows 10. Immediately after I upgraded to Windows 10, I could not scan, so I reinstalled the printer software and has worked for a day or two and then the printer would print not unless I restarted the printer or the computer - sometimes 2 or 3 times. This went on for a few weeks, sometimes it would be nice, sometimes, usually after the computer restarts, he would simply go offline. Once, he went offline 3 times when I was printing about 20 postage labels, recently he went 1 week without any problems.

  Long story short, after a lot of troubleshooting and to help a friend to HP, I found the problem to be associated with the WSD/service Port in Windows 10. My printer still maintains a stable connection with my Netgear router (wireless to the printer light stays on blue) and I was able to scan from the HP software and I could ping the printer... but printing would be just stuck in the print queue (the spooler service) and the printer showed offline in the queue, hardware and windows devices , or when printing from a program like Windows.

  I learned that if I went in devices and printers, until I sent a print job, if the printer showed offline, I could save time by restarting the printer simply and he would come every time (less painful) online.

  

  But it's just a solution and not a solution.

  Nothing worked... not even print and scan doctor. The final fix that worked was to define an IP address manually for the printer, and then I put the print driver to use a standard TCP/IP port.

  Here is the step by step. Your printer must already be connected to your network (solid blue on printer).

  Step 1: Make sure your printer uses a manual IP address

  (1) to obtain the IP address of your printer:

  • If your printer has a control panel with a menu, it's easy... Just look in the settings menu without wire/report and write your printer IPv4 address.
  • If your printer is not a menu of fancy and repower the computer and printer HP Print and Scan Doctor network menu display use (wireless), or you can connect to your router from a web browser (usually 192.168.1.1) and look at attached IPs (like me). Some printers can also print a report of the network when you hold down some buttons everything back up and running, but you will need to search the web site of the Internet or HP to find the process for your printer model - the report displays the IP Address of the printer.

  (2) once you have the IP address of the printer number, type this information in a web browser... like 192.168.1.x (where x is the last number of your printer)

  Web page of the printer should find - otherwise, use another browser (you can use a tablet or iPad if you want). HP has several different forms of printing of web pages (embedded web servers) depending on your printer model, but they all have a large number of parameters.

  (3) since the network tab or section, look for a manual IP address configuration.

  

  (4) suggest an IP address or type in a new.  I've personally used suggest and then replaced by the last number 241. You want to use a high number, something in the order of 240 to 250 to reduce the risk of problems caused by your router assign this number to something else on your network. Note the 4 digits for the new IP address manual, you will use them later.

  5) click apply and close the web page of the printer.

  Step 2: Make the print driver using the manual IP address of the printer

  Open the devices and printers in Windows, right click on your printing device and select printer properties. Follow the prompts to get the WSD port and on a new local port...

  

  1) click on the ports tab.

  (2) add the Port.

  (3) click on after the first screen, and then click new port type.

  (4) enter the IP address of the printer.

  (5) next.

  (6) select the new port.

  7) click OK.

  You have now two pilots displayed in the printers and devices window, you can now print... but you might not be able to scan and the HP printing software may not work as he might want to lets you add a new printer when you open it... If Yes, proceed to step 3.

  Step 3: Remove print devices and install a new one.

  Need to do this to get the software back HP synchronized so you can scan.

  (1) right click 2 print devices listed in the window of your printer and remove them by clicking on remove device.

  (2) open the HP printer Assistant software (from the icon on the desktop or you can search Windows by using the name of your printer).

  (3) installation/add a new printer... go fast and a new device icon is added to the printers and devices window.

  4) return to the printers and devices window and open the properties of the printer again for your printer icon.

  5) go to the ports tab (yet) and you'll see a new selected WSD port, select Port Standard, you created earlier in step 2.

  (6) you have now two print devices in the window (again), but now everything should work.

  These two devices alone from here on out. Do not remove one and everything should work fine. At least it worked for me. I hope it works for you. I'm hoping a Windows update resolves this problem soon, I see many people who cannot print or scan wireless after they upgraded - not just the stuff of HP.

• Unable to activate Windows 7 after the replacement of a hard drive.

  * Original title: new hard drive and W7 activation

  H all the

  I have computer problems and plug a new 1 TB hard drive, to replace my old 500 GB drive, which became unreliable.
  I cloned my drive to the new, and it works well, how not says windows must be activated and cant.
  Help
  Thank you
   
   
  Repair and recovery Forum left Windows 7.

  Hello

  1. have you tried to activate the Windows 7 product key?

  2. do you get an error message?

  When you make a significant hardware change to your computer, such as upgrading the hard disk and memory at the same time, you may be required to activate Windows again. For more information, see Activate Windows 7 on this computer.

  I suggest to activate Windows 7 by phone activation product key and check.

  Activation of the phone:

  a. click Startand in the search for box type: slui.exe 4.

  b. press ENTER on your keyboard.

  c. Select your country.

  d. take the phone activation option and brace yourself for a real person.

  For more information, visit.

  Activate Windows 7: frequently asked questions

   

  How to contact a Microsoft Product Activation Center by phone

   

  Please update with the results. We will be happy to help you.