How to rebuild Raid1 on Poweredge T110 II

I have PowerEdge T110 II with RAID 1 created.

The disk0 failed.  At the moment only disk1 is running.

I would like to replace with a new HDD disk0 and make mirrored (RAID 1) with the disk0.   How to rebuild Raid1?

I look for "Rebuild" option but did not find any look like him.

Kind regards

Kawin

Hi Martin,

Great info, clears up things on my side.

It is here.

Remove the RAID VD, in this case of the last screenshot, the low VD.

After removal, a hard drive will be available for the assignment of immediate replacement. Reconstruction should start as soon as possible, a spare drive is available.

Let me know how it goes. : )

Tags: Dell Servers

Similar Questions

  • How vm can my Dell poweredge T110 run?

    How my Dell Poweredge T110 yourself run the specs are

    Processor Intel Xeon X 3450 (2.66 Ghz, 8 MB Cache, 95W TDP, Turbo, HT), DDR3 - 1333 Mhz

    Neniry 8GB (UDIMM rank double 2 x 4 GB) 1333 Mhz

    HD 1 x 250 GB 3 x 1 TB SATA

    1 x adapter Server Intel PRO 1000PT Port GbE, Cu, PCIe x 1

    a friend sayd I can run only 2 VM

    You can see one of the 2 CPU servers with 4 or 6 cores per processor. Similar to your T110 would be the T410. Add the second processor enough RAM and hardware raid controller. You can have SAS rather than SATA drives and you're better off with several discs smaller than smaller disks for better performance.

  • OS on PowerEdge T110 II deployment

    We just got a PowerEdge T110 II, I followed the instructions I found on the forums like and support documents: use the life cycle, boot on DVD OpenManage,.

    Nothing has worked

    In fact, my server has no life cycle, he has Unified Server Configurator instead. I tried to use the USC and was stuck at the point when he asks for the source of the drivers and the location of the catalog.

    I extracted the relevant drivers in the OS I have try to install - win 2012 R2, I put it in a USB port. Still could not bypass this step.

    I appreciate all help:

    First how to install life cycle?

    How to bypass the step asking the source location and the driver catalog?

    Finally, how to install OS?

    The T110 II, as noted, is not a lifecycle controller.

    Ignore the installation utilities and install directly from the OS to install media.

  • Server installation 2012 on PowerEdge T110 II in Raid Mode

    I am trying to install Windows Server 2012 on a server PowerEdge T110 II that I just bought.  No software utility disk and the driver provided with the computer!  When I try to install Windows directly from the OS installation disc it tells me that some drivers are missing however it does not list all the specific missing to find out what is missing!  The message reads: "a media computer driver needs is missing."  This could be a DVD, USB or a disk in hard disk driver.  If you have a CD, DVD or USB flash drive with the driver on this subject, please insert it now... »

    I read in Guide_en of the user Instructions 2012_Installation your Microsoft Windows Server-we document that I need 7.2 OpenManage that supports the installation of operating system Windows Server 2012.  I got the ISO of OpenManage 7.2.0 A01 from your Web site and burned it to a DVD.  I started the computer with this DVD and was able to get for Dell Systems Build and Update Utility.  From there, I went to set up against Installation OS Server.  It provides a list of supported OS.  Windows server 2008 and 2011 are listed but not 2012!

    When I go into the BIOS (PERC S100, version 2.2.3) and change the setting of SATA in ATA and run OpenManage and go to Dell Systems Build and update utility and configure the server against, to presents this time Windows Server 2012 and I am able to go further until it gets to 100% full and restarts.  I insert the installation of Server 2012 DVD during the reboot and it states that "the valid operating system installation media was found.  Press 'OK' to start to install. "A system Build and Update Utility message appears which States:"the temporary Partition is removed.  If an error occurred during the installation of the operating system, you will need to use the Systems Build and Update Utility to restart the installation process. "I press OK and get a Windows Installer message that says:"the file 'autorun.dll' could not be loaded or is corrupt. Setup cannot continue. Error code is [0xC1] 'I burned the DVD of the BONE from an ISO from Microsoft.  I read that maybe the DVD must be burned differently and at a slower speed.  Who can solve this question (not sure yet), but I would like to configure this computer in RAID mode anyway, and first I have to solve the following question:

    (1) is it still possible to install Windows Server 2012 with the Raid Configuration on this material?  If so, how?  The OpenManage--> Dell Systems Build and update utility--> set up against server does not list server 2012 unless the SATA is not set to RAID!

    (2) when I set up the same computer with Server 2012 as the operating system installed on the site configure from Dell.com and to buy, it gives a configuration error that says "error: 2012 options selected operating system from Microsoft require Microsoft 2012 media.» When I pick/check ' Windows Server 2012, edition Foundation, press release "the error disappears.  Do I need this press kit?  -What is the origin of the problem with the installation?  And where can I get this missing element?

    Any guidance you can give me or reference to material appropriate/docs for help would be appreciate because I have lost/spent several days trying to get this installed server operating system!  Thank you.

    The T110 II is almost two years, then Yes, compared to 12 G systems, is using older hardware (I suspect that replacement is the T110 II should be out soon).  The S100/S110 is a special implementation of Intel RAID on board, so the S110 is not an option on the older boards that have the S100.

    ftp.dell.com/.../DELL_MULTI-DEVICE_A05_R294489.exe

    Good luck.

  • PowerEdge T110 II/PERC H200 drive Expansion Question

    We have a server PowerEdge T110-11 with two 600 GB 15K SCSI disks in a RAID 1 configuration via a PERC H200 controller.  This server is used in a production environment.  We want to add an extra internal drive on the server, but the readers (or reader) not be used for archival purposes.  Check-in will be only done periodically at defined intervals.  The plan of production a need for speed and redundancy of the RAID/SCSI setting.  The drive to check-in will not.  I don't know what is supported by the PERC H200 beyond two units SCSI that we have.  How would you recommend that we do that?  Should we buy two SATA drives and use them in a RAID 1 configuration as we have for SCSI drives?  All readers are saved on a Dell RD1000 disk cartridge system, in a way.  I don't know if we need RAID for this disk to archive, because it will be backed up regularly.  Others grow here to use an external USB drive for archiving, due to their very low cost.

    Thanks for your suggestions, you can offer.

    Hello.

    Support-T110 II up to 6 hard drives. It wouldn't hurt to implement these drives in RAID 1 or RAID 5 (for more than 2 disks) configuration just in case of failure before the archive is saved. If your archive is not so important, you can set the drives in RAID 0.

  • Intrusion status PowerEdge T110 II can not be reset

    Hello

    I have a PowerEdge T110 II which is flashing orange health status indicator. The OMSA, the problem was the intrusion alert. I opened the front cover, but now it is closed. How can I reset this alert? I read somewhere to go to the security configuration of the bios to reset it, but there is no encroachment setting it at all. I even updated the bios with the latest version. Any help much appreciated.

    Thank you

    Lee_Km,

    Normally this amber should go back to blue when the cover is restored. I want to watch updates iDrac on the server as well as access to the iDrac (Ctrl-E) and then clear the logs. If the error reappears, then remove the cover and see if now the Intrusion PIN down sensor manually disables the error. If yes reinstall it the lid and make sure the PIN is depressed and clears the error. If none of this works, you can also try to reconnect cable Intrusion sensors as well.

    Let me know the results.

  • How to rebuild icon cache?

    How to rebuild icon cache? I have Windows XP Home Edition.

    http://Windows.Microsoft.com/en-us/Windows/downloads/Windows-XP

    Tweak UI

    You can use this Microsoft utility to rebuild and repair icons, I have used this utility for many reasons, but I've never needed to rebuild or repair icons, it should work.

    You will find on the homepage in the featured downloads tab.

    The section icons of reconstruction is being repaired in the menu.

  • How to rebuild the icon cache

    How to rebuild the icon cache? My icons randomly change on my computer.

    Hi ErikaVR,
     
    -Did you of recent changes made to your computer before this problem?
     
    This behavior can occur if the icon cache is not properly updated.
     
    Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

     
    Follow the steps listed in this article to resolve the problem:
  • What type of graphics card can I put Poweredge T110 II?

    A result of slots server:

    4 PCIe G2 slots:
    Two x 8 slots (one with x 16 connectors)
    One x 4 slot (with x 8 connector)
    A x 1 slot

    Graphics must support Windows server 2012 (are Windows 8, Windows Server 2012-compatible drivers?). I not looking for something fancy or fast, just something that can take care of 2 monitors via DVI or DisplayPort.

    I looked at NewEgg section of graphics card and it is difficult to understand what type of interface I should take. This is what NewEgg for interface (I see no x 8 or x 4 as shown in the Poweredge T110 II specs):

    PCI Express 3.0 x 16
    PCI Express 2.1 x 16
    PCI Express 2.0 x 16
    PCI Express x 16
    PCI Express x 1
    PCI Express 2.0
    PCI Express 2.1
    PCI Express 3.0

    I would like to try any of the cards with x 8 to the end, even though it says a slot x 16 capacity, but only x 8 power.  The card can only be up to 25w.

    Kind regards

  • Dell PowerEdge T110 II add on the video graphics card that works

    The system configuration:
    Dell PowerEdge T110 II
    BIOS 2.8.0
    RAM 2x8GB

    For many reasons (for example feeding bus PCI), it is difficult to install a Dell PowerEdge T110 II graphics card.  The ATI Radeon HD 5450 is a good choice for the Dell PowerEdge T110 II because if its (approximately 10W) low energy consumption.

    After trying several HD 5450 (listed below), a graphics card that works is a "VisionTek Radeon HD 5450 - graphics card - Radeon HD 5450 - 2 GB memory DDR3 - PCI Express 2.1 x 16'.

    Edit: Thanks to paikat for the following references, (see his assignment for the links, where to buy)...
    VisionTek manufacturer: 900356
    Reference Dell: A6173020

    This card works when the monitor is connected to the VGA/D-SUB/DB15 connector. I wasn't looking to connect to HDMI or DVI connectors.

    After you install this graphics card, passed the BIOS Setup:
    Integrated Devices > integrated video controller: enabled

    by saying:
    Integrated Devices > integrated video controller: Standard

    and allowed to move from "Standard" to "Distributed" so it now says:
    Integrated Devices > integrated video controller: distributed

    Note: Install the card with the monitor connected to the integrated video port / edge, change the BIOS to Distributed settings, restart the computer and then connect the monitor to the Discrete / distributed / video port to Add on.

    Here are the identifiers on the "VisionTek Radeon HD 5450 - graphics card - Radeon HD 5450 - 2 GB memory DDR3 - PCI Express 2.1 x 16'

    54502GBPC
    VT 5450 PCIe 2GB V/D/H
    VT-400746PC
    PCB #R81KLD-PJ3Z
    R71KLD
    R81KLD
    Version: 1.0
    G0850000-0351L002739CZA-0087
    SH6 94V-0
    E248779

    Here are some pictures of the 5450 VT from DELL:

    Other video cards that have been tested and work well in T110 II are:

    * XFX Radeon HD 5450 1 GB GDDR3 VGA/DVI/HDMI Low Profile PCI-Express graphics AMD card HD545XZQH2; HD-545 X-ZQH2
    Note there is another version of this card is ONXFX1PLS2 who has not tested.

    * EX-PX610GT-video JATON GeForce GT 610 2 GB 128 - Bit DDR3 PCI Express 2.0 x 16 HDCP ready low profile ready card video

    * Reference DELL SOUND H545H1G Radeon HD 5450 (Cedar) 1 GB memory DDR3 64 bit PCI Express 2.1 x 16

    I hope this can help others avoid the frustration when you try to install a video card in a Dell PowerEdge T110 II.

    SR2002
    I have read this thread and seen the suggestion of VisionTek, it also works with the card mother E3-1230V2?

    My guess is the Dell PowerEdge T110 II uses the same motherboard for various configurations of CPU, but this is only a guess.

    SR2002
    Also, are there better options eventually with the support of 12 DDR5 and directx?

    None that I know, but I've only tried a few cards. Please let us know if you find cards better than the VisionTek 900356

    SR2002
    I saw a thread suggesting ASUS GTX650-E-2GD5, someone at - he of the inputs on this card?

    I tried a GeForce GT 610 2 GB and it did not work.  Check the use of the GTX650-E-2GD5 (DPT) power and make sure that it is less than 25 watts (see below)

    Quick notes:

    1. the location of PCIe x 16 is actually a "full-size x 8 slot" (also known as an x 16 slot / x 8) and the video card needs to work in this type of accommodation.

    2. video card power (TDP) is a limiting factor. Technical guide Dell says "the system supports a maximum power of 25 W for all four cards PCIe.»  and said Dell owner's manual "ATTENTION: to ensure correct cooling, not more than two cards of four extension may have more than 15 W power consumption (maximum 25 W each), not to mention the integrated storage controller card."

    3 install the card with the monitor connected to the integrated video port / edge, change the built-in BIOS devices > on-board video controller 'Activated' / 'Standard' to 'Distributed', restart the computer and then connect the monitor to the Discrete / distributed / video port to Add on.

  • Cannot install Windows Server on the new server Poweredge T110 II 2012

    HI - just took delivery of my new Dell PowerEdge T110 II with two 1 TB drives in RAID 1, but without any operating system installed.  On the Windows Server 2012 Standard edition installation, the installation routine is unable to detect readers when it comes to choosing the installation location.  I can 'find the pilots', but on the insertion of the Dell supplied DVD, it does not find everything.  I changed different settings, rebooted and tried several times without success.  Entering the system at boot configuration screens, I can clearly see my 2 x 931GB disks and the virtual drives installed on them (I even removed the implementation of RAID and the virtual drives at some point to see if that was the problem).  Any help appreciated.  Regards, Barry

    Hello Barry

    You should have received a disc entitled management of system and Documentation Tools. If you start on this DVD, it takes an option to install an operating system. Follow the on-screen instructions and it should load the required drivers. If this does not work then let me know what RAID controller you have.

    Thank you

  • Windows 7 will run on a PowerEdge T110 ii? Network drivers?

    I searched the forum search, but couldn't find a clear answer.

    Is - this Windows 7 64-bit work a Poweredge T110 ii? with hard disks that are mirrored and the network drivers? I plan on buying a brand new ii of T110, but I watched the support drivers and did not find Windows 7 on this list, only the Server 2008 and other. Please notify. I want a quality system of server for reliability, but with a client OS.

    I used the Dell system Build and Update Utility to install Win7 on my PE T610. Since the system disk build, I chose Win Server 2008 R2 as the OS to install. I believe that this creates an installation environment with the appropriate drivers for your hardware. After a reboot, the Build environment system asks you to insert the OS installation disc in which case I insert my Win7 installation disc. The process then continues as normal win7 installation process. No need to load the drivers, etc as this has already been done by the utility of generation.

    Note that some features will not work without effort. OMSA must, for example, some functions of the server operating system to this fact will not easily run on a desktop based system. It makes it more difficult to administer your Windows computer.

  • upgrading ram on PowerEdge T110 II da 8 GB 16 GB [CF]

    Ciao

    Ho Server PowerEdge T110 II UN

    Che went up 4 banchi di ram by total di UN 8 GB

    DM0KY DUAL IN-LINE MEMORY MODULE, 2G, 1333, 1RX8, 8, 240, UBE, LOW VOLTAGE

    ROM portarlo 16 GB

    changing Reed tutti i banchi

    quindi 2 da 8 gb

    COSA posso fare?

    Bongiorno, the sto contattando by mail.

  • PowerEdge T110 raid necessary emergency assistance

    Hi all

    I have dell server poweredge t110 without raid controller card

    When I try to configure raid 1 hard disk SATA 2 motherboard it configured properly on the motherboard, but when I try to install any OS, I found it see them 2 HDD, not one

    so I'm going back to the motherboard, I found the not configured raid

    1. I need management system capable of boot CD for dell poweredge t110?

    I bought the controller raid (Dell SAS 5I Raid Controller UN939 - UCS51) when I put it on the server, I found when I start my server, but when I press CTRL + C to set up raid but I can't find my sata hard drives

    2 is compatible with poweredge t110 sata Server (Dell SAS 5I Raid Controller UN939 - UCS51) + hard drive?

    3 - if (Dell SAS 5I Controller Raid un939 - UCS51) not comapatible with my case what is the best work of raid controller with poweredge T110 with a disk sata hard 4 to make them raid 1

    "but what I get from your advice (JW063 - SAS, SAS6/IR controller card) cannot configure hard disk of 2 TB sata raid 1 and shown 1 TB > is it good?

    N °

    A SAS 6/iR may use up to 2 TB of hard drives.  It also has a virtual disk BOOTABLE maximum (table) size of 2 TB.  So, YOU have the following items:

    • 2x2TB disks configured as 2 TB RAID 1, bootable or not.
    • 2x1To configured as a 1 TB RAID 1, disk bootable or not.
    • 2x1To configured as 2 TB RAID 0, disk bootable or not.
    • 2x1To disks configured as first 1 TB RAID 1 (bootable), AND 2x1To set up as second 1 TB RAID 1 disks.
    • 2x2TB disks configured as first 2 TB RAID 1 (bootable), AND 2x2TB disks configured as a second 2 TB RAID 1.
    • 2x1To disks configured as first 1 TB RAID 1 (bootable), AND 4x1TB disks configured as a second 4 TB RAID 0 (not bootable).

    You can NOT have the following:

    • 2x2TB disks configured in 4 TB RAID 0 for OS bootable.
    • 4x1TB disks configured in 4 TB RAID 0 for OS bootable.

    "but my case is that I want to 4 TB (4 sata hard disk 1 TB) configured for RAID 1 and shown 2 TB after raid 1.

    You can't have a 4 drive RAID 1 - a RAID 1 requires only and exactly 2 disks.  A RAID 1 with two 1 TB drives is equal to only 1 TB of total space.  The only way to configure both drives of 1 TB to 2 TB show is to make a RAID 0 2-disc.  RAID 0 is dangerous, because if a disk fails, all of THE data on BOTH drives is unusable.

    That's what you do:

    2x1To first 1 TB RAID 1 for operating system drives.
    2x1To records in second 1 TB RAID 1 for your partition data per second.

  • How to rebuild the registry key 'Hkey_local_machine\software\microsoft\windows\currentversion\explorer\folderdescriptions '.

    How to rebuild the registry key 'Hkey_local_machine\software\microsoft\windows\currentversion\explorer\folderdescriptions '.

    Hello

    Hkey_local_machine\software\microsoft\windows\currentversion\explorer\folderdescriptions

    Try to run the system restore.

    Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

    To run System Restore, you can consult the following link:

    How to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows 7:

    http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

Maybe you are looking for