'How to' set up a VPN between a UC540 and a SR520 with remote IP extension
Hi all
I need help in establishing a link between a head office UC540 and a distance SR520 I want to use a PC and an IP phone in. This remote site is the first of many.
I found several examples of IPsec VPN site, but none with references to some VLAN voice and data, should I worry or the phone will only work.
All the tips and suggestions accepted with gratitude,
Jerry
Here is an example of configuration LAN-to-LAN VPN between 2 IOS routers:
http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080194650.shtml
Assuming that your example:
VLAN 1 - data - 192.168.19.0/24
VLAN 100 - voice - 10.1.1.0/24
And on the other side:
VLAN 1 - data - 192.168.20.0/24
VLAN 100 - voice: 10.2.2.0/24
The crypto ACL would be:
access-list 150 permit ip 192.168.19.0 0.0.0.255 192.168.20.0 0.0.0.255
access-list 150 permit ip 10.1.1.0 0.0.0.255 10.2.2.0 0.0.0.255
Crypto ACLs on the other side are the following:
access-list 150 permit ip 192.168.20.0 0.0.0.255 192.168.19.0 0.0.0.255
access-list 150 permit ip 10.2.2.0 0.0.0.255 10.1.1.0 0.0.0.255
Tags: Cisco Security
Similar Questions
-
Setting up a VPN between a WRVS4400N and ASA device
I'm a newbie when it comes to Cisco devices and I have a problem setting a VPN between a local and a seat some distance away.
Here, our local office, we have a device Cisco WRVS4400N Small Business.
At Headquarters, they have a feature of Cisco ASA.
We must set up a point to point VPN and I have no idea how to proceed with these devices.
To compound things, resources, I'm at the other end in an unknown entity that also does not seem to have a lot of experience with this.
Is there any type of step by step guide for such a configuration?
If not, can someone please help with this?
Hello William,.
I would call 1866-606-1866 Support Center for assistance on the side the tunnel then the entire side of the ASA WRVS has to do is match the settings. If the side ASA needs support with which we can transfer more TAC.
Cisco Small Business Support Center
Randy Manthey
CCNA, CCNA - security
-
VPN between a PIX and a VPN 3000
I'm trying to set up a VPN between PIX and a VPN 3000. All configurations are complete, but the tunnel has not been established. On the PIX, to 'see the crypto engine' and ' show isakmp his ' orders, I do not see the tunnel. Of "show ipsec his ' command, I can see the mistakes"#send"continues to increase when I try to connect to the remote network. Here is the copy - paste command:
Tag crypto map: myvpnmap, local addr. 10.70.24.2
local ident (addr, mask, prot, port): (10.70.24.128/255.255.255.128/0/0)
Remote ident (addr, mask, prot, port): (10.96.0.0/255.224.0.0/0/0)
current_peer: 10.70.16.5:0
LICENCE, flags is {origin_is_acl},
#pkts program: encrypt 0, #pkts: 0, #pkts 0 digest
#pkts decaps: 0, #pkts decrypt: 0, #pkts check 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0, #pkts decompress failed:
#send 12, #recv errors 0
local crypto endpt. : 10.70.24.2, remote Start crypto. : 10.70.16.5
Path mtu 1500, fresh ipsec generals 0, media, mtu 1500
current outbound SPI: 0
SAS of the esp on arrival:
the arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
outgoing ah sas:
outgoing CFP sas:
Obviously, the PIX identifies protected traffic but failed to establish the tunnel. I was wondering what could be the reason for these kind of mistakes? That means them growing '#send errors?
Thank you very much!
Sending error mean simply the PIX is grateful to encrypt this traffic, but there is no built tunnel and so it must drop the package.
you will need to look at why the tunnel is not under construction however, "sending error" are just a byproduct of some other configuration issue. On the PIX, it looks like you would have something like:
Crypto ip 10.70.24.128 access list allow 255.255.255.128 10.96.0.0 255.224.0.0
On the 3000 under the L2L section and the Local and remote network, you need the exact opposite of the latter, then it would be:
/ Local network mask = 10.96.0.0/0.31.255.255
/ Remote network mask = 10.70.24.128/0.0.0.127
If you have something else the tunnel will fail to come. Otherwise, we see that the Cryptography debugs the PIX and the trunk of the 3000 when the tunnel is built.
-
PPTP VPN between clients Windows and Cisco 2921 router
Hi all!
I have a problem with PPTP VPN between Windows clients and router Cisco 2921 with permission of RADIUS (IAS). When I try to connect to Cisco 2921 of Windows 7 by using MS-CHAP v2 I get the message 778: it was not possible to verify the identity of the server. Can I use PAP - power is OK. On Windows XP, the same situation.
Cisco config:
version 15.0
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
hostname gw.izmv
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
!
AAA new-model
!
AAA authentication ppp default local radius group of
!
AAA - the id of the joint session
!
clock timezone + 002 2
!
No ipv6 cef
IP source-route
IP cef
!
!
Authenticated MultiLink bundle-name Panel
!
Async-bootp Server dns 192.168.192.XX
VPDN enable
!
VPDN-Group 1
! PPTP by default VPDN group
accept-dialin
Pptp Protocol
virtual-model 1
echo tunnel PPTP 10
tunnel L2TP non-session timeout 15
PMTU IP
adjusting IP mtu
!
redundancy
!
interface Loopback0
IP 192.168.207.1 255.255.255.0
!
!
interface GigabitEthernet0/0
Description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE $ 0/0
IP 192.168.192.XXX 255.255.255.0
IP 192.168.192.XX 255.255.255.0 secondary
IP nat inside
IP virtual-reassembly
automatic duplex
automatic speed
!
!
interface GigabitEthernet0/1
no ip address
Shutdown
automatic duplex
automatic speed
!
!
interface GigabitEthernet0/2
Description - Inet-
no ip address
NAT outside IP
IP virtual-reassembly
automatic duplex
automatic speed
PPPoE enable global group
PPPoE-client dial-pool-number 1
No cdp enable
!
!
interface virtual-Template1
IP unnumbered Loopback0
IP mtu 1492
IP virtual-reassembly
AutoDetect encapsulation ppp
by default PPP peer ip address pool
PPP mppe auto encryption required
PPP authentication ms-chap-v2
!
!
interface Dialer1
the negotiated IP address
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
Dialer-Group 1
PPP authentication pap callin
PPP pap sent-username DSLUSERNAME password DSLPASSWORD
No cdp enable
!
!
IP local pool PPP 192.168.207.200 192.168.207.250
IP forward-Protocol ND
!
!
overload of IP nat inside source list NAT_ACL interface Dialer1
IP nat inside source static tcp 192.168.192.XX 25 expandable 25 82.XXX.XXX.XXX
IP nat inside source static tcp 192.168.192.XX 1352 82.XXX.XXX.XXX 1352 extensible
IP route 0.0.0.0 0.0.0.0 Dialer1
!
NAT_ACL extended IP access list
deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255
deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255
deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255
deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255
permit tcp 192.168.192.0 0.0.0.255 any eq www
permit tcp 192.168.192.0 0.0.0.255 any eq 443
permit tcp 192.168.192.0 0.0.0.255 any eq 1352
permit tcp host 192.168.192.XX no matter what eq smtp
permit tcp 192.168.192.0 0.0.0.255 any eq 22
permit tcp host 192.168.192.XX no matter what eq field
permit tcp host 192.168.192.XX no matter what eq field
permit tcp host 192.168.192.XX no matter what eq field
allowed UDP host 192.168.192.XX matter what eq field
allowed UDP host 192.168.192.XX matter what eq field
allowed UDP host 192.168.192.XX matter what eq field
!
host 192.168.192.XX auth-port 1645 1646 RADIUS server acct-port
Server RADIUS IASKEY key
!
control plan
!
!
!
Line con 0
line to 0
line vty 0 4
line vty 5 15
!
Scheduler allocate 20000 1000
end
Debugging is followed:
14:47:51.755 on 21 oct: PPP: Alloc context [294C7BC4]
14:47:51.755 on 21 oct: ppp98 PPP: Phase is
14:47:51.755 on 21 oct: ppp98 PPP: using AAA Id Unique = 8 b
14:47:51.755 on 21 oct: ppp98 PPP: permission NOT required
14:47:51.755 on 21 oct: ppp98 PPP: via vpn, set the direction of the call
14:47:51.755 on 21 oct: ppp98 PPP: treatment of connection as a callin
14:47:51.755 on 21 oct: ppp98 PPP: Session Session handle [62] id [98]
14:47:51.755 on 21 oct: ppp98 TPIF: State of the event [OPEN] [initial check]
14:47:51.755 on 21 oct: ppp98 PPP LCP: switch to passive mode, State [stopped]
14:47:53.759 on 21 oct: ppp98 PPP LCP: exit passive mode, State [departure]
14:47:53.759 on 21 oct: LCP ppp98: O CONFREQ [departure] id 1 len 19
14:47:53.759 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)
14:47:53.759 on 21 oct: ppp98 TPIF: AuthProto MS-CHAP-V2 (0x0305C22381)
14:47:53.759 on 21 oct: ppp98 TPIF: MagicNumber 0xF018D237 (0x0506F018D237)
14:47:53.759 on 21 oct: ppp98 TPIF: event [UP] State [departure at REQsent]
14:47:54.351 on 21 oct: ppp98 TPIF: I CONFREQ [REQsent] id 0 len 18
14:47:54.351 on 21 oct: ppp98 TPIF: MRU 1400 (0 x 01040578)
14:47:54.351 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)
14:47:54.351 on 21 oct: ppp98 TPIF: PFC (0 x 0702)
14:47:54.351 on 21 oct: ppp98 TPIF: RAC (0 x 0802)
14:47:54.351 on 21 oct: LCP ppp98: O CONFNAK [REQsent] id 0 len 8
14:47:54.351 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)
14:47:54.351 on 21 oct: ppp98 TPIF: State of the event [receive ConfReq-] [REQsent to REQsent]
14:47:54.751 on 21 oct: ppp98 TPIF: I CONFACK [REQsent] id 1 len 19
14:47:54.751 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)
14:47:54.751 on 21 oct: ppp98 TPIF: AuthProto MS-CHAP-V2 (0x0305C22381)
14:47:54.751 on 21 oct: ppp98 TPIF: MagicNumber 0xF018D237 (0x0506F018D237)
14:47:54.751 on 21 oct: ppp98 TPIF: State of the event [receive ConfAck] [REQsent to ACKrcvd]
14:47:54.915 on 21 oct: ppp98 TPIF: I CONFREQ [ACKrcvd] id 1 len 18
14:47:54.915 on 21 oct: ppp98 TPIF: MRU 1400 (0 x 01040578)
14:47:54.915 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)
14:47:54.915 on 21 oct: ppp98 TPIF: PFC (0 x 0702)
14:47:54.915 on 21 oct: ppp98 TPIF: RAC (0 x 0802)
14:47:54.915 on 21 oct: LCP ppp98: O CONFNAK [ACKrcvd] id 1 len 8
14:47:54.915 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)
14:47:54.915 on 21 oct: ppp98 TPIF: State of the event [receive ConfReq-] [ACKrcvd to ACKrcvd]
14:47:55.275 on 21 oct: ppp98 TPIF: I CONFREQ [ACKrcvd] id 2 len 18
14:47:55.275 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)
14:47:55.275 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)
14:47:55.275 on 21 oct: ppp98 TPIF: PFC (0 x 0702)
14:47:55.275 on 21 oct: ppp98 TPIF: RAC (0 x 0802)
14:47:55.275 on 21 oct: LCP ppp98: O CONFACK [ACKrcvd] id 2 len 18
14:47:55.275 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)
14:47:55.275 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)
14:47:55.275 on 21 oct: ppp98 TPIF: PFC (0 x 0702)
14:47:55.275 on 21 oct: ppp98 TPIF: RAC (0 x 0802)
14:47:55.275 on 21 oct: ppp98 TPIF: State of the event [receive ConfReq +] [ACKrcvd to open]
14:47:55.295 on 21 oct: ppp98 PPP: Phase is AUTHENTICATING,
14:47:55.295 on 21 oct: ppp98 MS-CHAP-V2: O CHALLENGE id 1 len 28 of 'gw.izmv '.
14:47:55.295 on 21 oct: ppp98 TPIF: State is open
14:47:55.583 on 21 oct: ppp98 MS-CHAP-V2: I ANSWER id 1 len 71 of "domain\username".
14:47:55.583 on 21 oct: ppp98 PPP: Phase TRANSFER, tempting with impatience
14:47:55.583 on 21 oct: ppp98 PPP: Phase is AUTHENTICATING, unauthenticated user
14:47:55.587 on 21 oct: ppp98 PPP: request sent MSCHAP_V2 LOGIN
14:47:55.591 on 21 oct: ppp98 PPP: received LOGIN response PASS
14:47:55.591 on 21 oct: ppp98 PPP AUTHOR: author data NOT available
14:47:55.591 on 21 oct: ppp98 PPP: Phase TRANSFER, tempting with impatience
14:47:55.595 on 21 oct: Vi3 PPP: Phase is AUTHENTICATING, authenticated user
14:47:55.595 on 21 oct: Vi3: given msg No. MS_CHAP_V2
14:47:55.595 on 21 oct: Vi3 MS-CHAP-V2: SUCCESS O id 1 len 46 msg is "tG @ #QDD @(@B@ (@[email protected]/ ** / @I @:[email protected]/ ** / @@@ EJFDE)).
14:47:55.595 on 21 oct: Vi3 PPP: Phase is in PLACE
14:47:55.595 on 21 oct: Vi3 CPIW: protocol configured, start state cf. [original]
14:47:55.595 on 21 oct: Vi3 CPIW: State of the event [OPEN] [Initial report on startup]
14:47:55.595 on 21 oct: Vi3 CPIW: O CONFREQ [departure] id 1 len 10
14:47:55.595 on 21 oct: Vi3 CPIW: address of 192.168.207.1 (0x0306C0A8CF01)
14:47:55.595 on 21 oct: Vi3 CPIW: event [UP] State [begins to REQsent]
14:47:55.595 on 21 oct: Vi3 CCP: protocol configured, start state cf. [original]
14:47:55.595 on 21 oct: Vi3 CCP: State of the event [OPEN] [Initial report on startup]
14:47:55.595 on 21 oct: Vi3 CCP: O CONFREQ [departure] id 1 len 10
14:47:55.595 on 21 oct: Vi3 CCP: MS - PPC supported bits 0 x 01000060 (0 x 120601000060)
14:47:55.595 on 21 oct: Vi3 CCP: event [UP] State [begins to REQsent]
14:47:55.599 on 21 oct: % LINK-3-UPDOWN: Interface virtual-access.3, changed State to
14:47:55.603 on 21 oct: % LINEPROTO-5-UPDOWN: Line protocol on Interface virtual-access.3, changed State to
14:47:56.027 on 21 oct: Vi3 LCP: I have TERMREQ [open] id 3 len 16
14:47:56.027 on 21 oct: Vi3 LCP: (0x2F7C5F7E003CCD740000030A)
14:47:56.027 on 21 oct: Vi3 CPIW: event [BOTTOM] State [REQsent on startup]
14:47:56.027 on 21 oct: Vi3 CPIW: State of event [CLOSE] [begins with initial]
14:47:56.027 on 21 oct: Vi3 CCP: event [BOTTOM] State [REQsent on startup]
14:47:56.027 on 21 oct: Vi3 PPP DISC: MPPE required not negotiated
14:47:56.027 on 21 oct: Vi3 PPP: sending Acct event [low] id [8B]
14:47:56.027 on 21 oct: Vi3 CCP: State of event [CLOSE] [start with initial]
14:47:56.027 on 21 oct: Vi3 LCP: O TERMACK [open] id 3 len 4
14:47:56.027 on 21 oct: Vi3 LCP: event [receive TermReq] State [Open to stop]
14:47:56.027 on 21 oct: Vi3 PPP: Phase ENDS
14:47:56.027 on 21 oct: Vi3 LCP: event [CLOSE] [off status of closing]
14:47:56.675 on 21 oct: Vi3 PPP: block vaccess to be released [0x10]
14:47:56.675 on 21 oct: Vi3 LCP: event [CLOSE] State [closing closing]
14:47:56.679 on 21 oct: Vi3 LCP: event [BOTTOM] State [closing on Initial]
14:47:56.679 on 21 oct: Vi3 PPP: compensation AAA Id Unique = 8 b
14:47:56.679 on 21 oct: Vi3 PPP: unlocked by [0x10] always locked by 0 x [0]
14:47:56.679 on 21 oct: Vi3 PPP: free previously blocked vaccess
14:47:56.679 on 21 oct: Vi3 PPP: Phase is BROKEN
14:47:56.679 on 21 oct: % LINK-3-UPDOWN: Interface virtual-access.3, changed State to down
14:47:56.683 on 21 oct: % LINEPROTO-5-UPDOWN: Line protocol on Interface virtual-access.3, state change downstairs
I'll be very grateful for any useful suggestions
We had the same problem using MS-CHAP-V2 and 3945 router using IOS 15.2. When you add the same combination of username/password locally it worked fine but it wasn't no of course of the solution. We have solved this problem by adding the following line in the config file:
AAA authorization network default authenticated if
This is because Windows 2000 clients require the use of a statement of authorization aaa in the router config. Maybe it was default (and therefore not shown) previous iOS releases.
Success!
Wil Schenkeveld
-
I followed the instructions to set up the home between my Mac and iPhone sharing 6, but I don't understand all the music on my iPhone
I have confirmed:
(1) devices are on the same network
(2) I am connected to my AppleID with the same account
3) are my OS up to date (Mac 10.11.2) (9.2 iPhone)
(3) I closed iTunes and the App has reopened(4) I turned my iPhone off and rebooted (and confirms the foregoing)
On my iPhone, I see in my music library, different ' kind' listed (e.g., classic, recently added, music of the 1990s, etc.) but they are all empty.
Im hoping to see the music I have in iTunes on my Mac and play these songs on my iPhone.
IM thinking, music that would be shared from my computer to my phone will be on the cloud?
(I did not all default to add my music in the cloud at the moment).
Post edited by: abbeyinor
Did you go into settings > music on your phone and sign in home sharing?
See you soon,.
GB
-
How to set the clock for the hours, minutes, and seconds with Windows XP
How to set the clock for the hours, minutes, and seconds with Windows XP
I don't know of your question. If you ask how to show the clock in the tray system with hours, minutes and seconds, then download & run "Tclock Light". Windows will not natively display the seconds.
TClock Light: <> http://homepage1.nifty.com/kazubon/tclocklight/index.html >
HTH,
JW -
Difference between Standalone Converter and converter integrated with VMware vCenter Server?
What is the difference between Standalone Converter and converter integrated with VMware vCenter Server, except that it comes integrated with Vcenter and another does not?Please confirm is there the technical differences between them?Also take a look at the Release Notes for vCenter Server 4.1.
of http://www.vmware.com/support/vsphere4/doc/vsp_esx41_vc41_rel_notes.html
VMware vCenter Converter plugin. VMware vSphere 4.1 and later versions of the update and patch are the latest editions of the VMware vCenter Converter plugin for vSphere Client. VMware will continue to update and support the free Converter Standalone product, which allows conversions from sources such as physical machines, machine formats virtual VMware and Microsoft and some third-party disk image formats.
André
-
IPSEC VPN between Pix 515E and 1841 router
Hi all
BACKGROUND
We have implemented a site to site VPN IPSEC between a Pix 515E 8.0 operation (4) and an 1841 using static IP addresses at both ends. We used CCP on the router and the ASDM the pix to build initial tunnels. Now the site with the router is evolving into a dynamic IP address from the ISP so we have implemented dynamic DNS to update dynamic IP address.
PROBLEM
The problem is that ASDM will not allow us to set a domain as the address of peers, it will not accept an IP address. We believe that the solution will be to remove the static Crypto map and replace it with a dynamic Crypto map on the side of Pix. Our questions are simply; is this the best solution? can change us the original static list or is it better to delete and make a new dynamic encryption card? Y at - it a shortcut to change the config command-line? This is a real network, so just check it out before make us any changes on the live kit.
Any help much appreciated.
You don't have to change anything when the peer-address changes. The dynamic crypto map aims to take dynamic peer connections. The only thing to remember, is that only the dynamic peer can initiate the connection. And you reduce your security if you use Pre-Shared key that now you can use a generic-PSK character.
As I remember, the PIX / ASA does not support the dynamic use of FQDNs for peer-resolution. This feature is supported in IOS.
For a feature, it would be preferable to static IP addresses on both sides.
-
How can I sync my email between my mac and my iPad
I'm a Road Runner e-mail account and use Outlook on Mac. I also have an iPad 2 Air which I just bought. Is it possible to sync my email between my mac and my iPad? I wish I could use my Mac or my iPad to check my email and store messages in my files. I currently can't do this on my Mac, I don't know how to synchronize between both devices. Did I ask for possible?
If the e-mail account can be configured as IMAP, you can add the account for both devices and they will keep in sync.
-
IPSec VPN between Cisco ASA and Fortigate1000
Hello
I find a useful document on how to create a tunnel VPN IPSec with ASA 5510 firewall Fortigate 1000...
the configuration of the coast FG is done without any problem, BUT the document (. doc FG) said I must configure the ASA with a GRE interface and assign an internal IP address in order to communicate with the FG...
The question is: How do I configure the interface on the SAA ACCORD?
Thanks in advance, Experts...
Kind regards...
ASA firewall does not support the interface/GRE GRE tunnel.
If you need to have GRE configured, you will need to complete the GRE tunnel on router IOS.
If you want to configure just pure tunnel VPN IPSec (lan-to-lan), here is an example of configuration on the side of the ASA:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080950890.shtml
Hope that helps.
-
VPN between 878 router and ASA 5505
Hello world
I struggled for a few days now to get a VPN connection works.
The situation
Two offices needs to be connected to eachother with a VPN. The two parties have a WAN connection.
The tunnel between locations rises very well but the communication fails in almost any way.
The host cannot ping each other and also the inside of the router and ASA pings fail.
The only ping works is from inside Site2 to the inside interface of the router side 1 (192.168.1.100 to 192.168.0.250)
NAT works very well on both sites behind the router / asa.
I think I'm doing something wrong with the roads or access lists but after 7 days, many refills, restores, driving from one end of the State to the other to reset stupid moves break and resolder my cable from the console and things completely with default start for 10 times, I'm through, I honestly don't know where to look for more...
Tech Specs:
Site1: has a cable modem that gives a WAN IP with DHCP address
This modem connects to the Cisco 878 (Fastethernet0) router
The router acts as a DHCP server and NAT gateway for the office and offers vpn connectivity to the other office
Site2: has a cable-modem/router (Cisco 3925), which made the NAT, this modem/router gives an IP private class-C (192.168.178.x)
This modem/router connects to a Cisco ASA 5505 (Fastethernet0)
The ASA also server as a DHCP server and NAT gateway for the office and offers vpn connectivity to the other office.
Online, it looks like this:
Office 1--> Cisco878--> WAN Cloud<---cablemodemrouter>---cablemodemrouter><--- asa5505="">---><--- office="">--->
IP address ranges:
Office 1
Network 192.168.0.0
Subnet mask 255.255.255.0
Gateway 192.168.0.250
IP WAN XXXX
Office 2
Network 192.168.1.0
Subnetmak 255.255.255.0
Gateway 192.168.1.1
IP WAN XXXX
On the location of office 2, there is a NAT between ASA and WAN router. between 192.168.178.x 255.255.255.0
The modemrouter is a Cisco 3925, on which IPSEC passthrough is enabled.
Configs:
Site 1:
CISCO 878 router
Site 2
ASA 5505
I hope someone has a chance to look through my config and tell me what I did wrong this week
Even if you can not help me but still read here: Thank YOU!
(As my problem has been resolved, I removed the configs of this post. If for any reason, you want to work for these devices configuration, please send me a PM)
Post edited by: taaa lijf - reason: problem solved, removed configs and stuff private for obvious reasons ;)
Hello
Ping client customer site 1 site2 and make sh crypto isakmp his and sh crypto ipsec his on the router.
If sh crypto isakmp gives QM_Idle and ping fails and you have no package in the HS cypto ipsec his and then do a debug crypto ipsec
If sh crypto isakmp gives MM_NoState can do a debug crypto isakmp
One note however, you should have ip addresses static at least on the side, initiating the tunnel, otherwise it will not work when ip address changes.
Kind regards.
Alain.
-
How can I put a dashed between enrty line and page number of an index?
I've successfully created an index with Indesign CC, but I can't seem to right align page numbers and get a dotted line between the entry and the page number. It doesn't seem to be an option for that. The menu of content table has a field "between entry and Page number", but I can't find an equivalent here.
There is also a full stop after each page number. I don't know how it got there, but how do I get rid of this?
You must change the paragraph style, you use with your texts to index. Go to the tabs tab and change the tab tab left justified right, Insert tab arrow to correct places on the rule of the tab and finally add a point to the head field. Then you need to return to your indexing settings and make sure that you separate the entries index and page number with tab...
Paragraph Style settings:
Indexing settings
-
I need help setting up a network between Windows Vista and Windows 7.
original title: HELP me to SET UP a NETWORK FOR WINDOWS VISTA AND PORTABLE WINDOWS 7 DESKTOP AND a DLINK WIRELESS ROUTER
HELP ME TO SET UP A NETWORK OF WINDOWS VISTA DESKTOP AND LAPTOP WINDOWS 7 AND A DLINK WIRELESS ROUTER
Hello
You can follow the procedure from the following link: networking computers running different versions of Windows: http://windows.microsoft.com/en-US/windows7/Networking-home-computers-running-different-versions-of-Windows
-
How do the areas of adjustment between the fields and lines in the apex?
(Request Express 4.2.5.00.08)
Hello world
I am beginner in the apex... When I created the form page, I found different spaces between the fields and lines... But I can't adjust it...?
Help me please
PIC
http://i.imgur.com/ZSFlmCi.PNG
Demo https://apex.oracle.com/pls/apex/f?p=50581:3:4430339212420:
PEAK http://i.imgur.com/T14TE3n.png
Hello
Solve this problem...
In the section "Attributes of the HTML Form element" for item writing: style = "" margin: 0px 1px 0px; ""
Thanks Amr
-
How to set the time difference between each data when using keithley 2400 scanning
Hello friends,
I use scanning Keithley vi the extent of SCANNING and acquire vi. I want to measure the voltage for each step and a pause between each two data, so I need a delay between each I step.
I'm a starter to use Labview, thank you very much for your answers.
Perry
As Dennis says, if you use the built-in scan function, you will need to consult the manual. See Section 10-16 (this is page 10 of article 16, only paragraphs not but 10, 16) for the manual Keithley 2400.
The Keithley 24xx series has a speed of measurement in units called PLC (Power Line Cycles). The default speed is 1PLC, which means a measure is taken with each cycle of line 1 power supply or 1/60th of a second (16.67ms). 24XX can range from 0.01 PLC (all 0.16ms) 10 PLC (all 166.6ms). The faster you measure, the less accuracy you get.
To programmatically set this value, the command is
ENSe:CURRent:NPLCycles
ENSe:VOLTage:NPLCycles
Depending on what you are sensing and where
is the number of controllers from 0.01 to 10. Another factor that will determine the time between data points is the cycle SDM. These are more complicated, look at your Keithley manual for more information. Look at article 6 and article 11 for more information.
Note:
PLC times are based on a cycle of 60 Hz US.
Maybe you are looking for
-
How view original owner?
I bought the iphone on eBay, but it's locked iCloud. How can I get in touch with the original owner of this phone on the return it? I didn't need privacy. Support Apple may give notice to the buyer? I know that first letter to her iCloud and domain I
-
After Update 9.3.5 connect my iPad iMessage
After Update 9.3.5 connect my iPad iMessage. He must have signed me apply the last update, but when I registered just in it sits on this... Any suggestions please?
-
While in firefox, I can click on finder and see the missing toolbar. As soon as I go back to firefox, it disappears.
-
HP pavilion g7-2259nr: Hp pavilion g7-2259nr Windows 7
Hello My girlfriend bought this laptop for me that came with Windows 8.I installed Windows 7 Professional 64-bit (Original), but I have some problems with it. I first noticed windows update continues to operate without finding anything and then I wen
-
every day, the backups fail
as a computer geek friend helped me every day that I get the message that my "last backup failed" How can I fix?