How to slow the rate of model

Similar Questions

• the time of acquisition of data - how to calculate the rate of analog output

  I want to calculate an acceptable rate of analog output, one that is taken in charge by material (PCIe6353), without the rate being changed by the VI DAQmx Timing (sample clock). The final objective is to have a rate of analog output that is an integer multiple of the analog input for precise frequency, since the sinusoid AO's amplifiers, which have a ringtone when AO updates occur.

  According to 27R8Q3YF of the knowledge base: how the actual scanning speed is determined when I specify the rate of scanning to My d..., the rate is revised as needed by calculating the rate of clock / asked for advice, divide the result rounded downwards and upwards in the clock of the Board and use the one that is closest to the requested speed.

  If 'Embedded clock' is selected, which is the result "Council clock.  DAQmx sample clock timebase Timing node - SampClk.Timebase.Rate says 100 ms/s. However, for a rate resulting from the update of 2.38095MS / s, the divisor of the time base timing node - "SampClk.TimebaseDiv" gives a value of 42. 42 x 2.38095 M = 99, 999, 990, where it should be 100 ms/s.

  How to calculate an acceptable rate of analog output is supported by the hardware? I have other plates, in addition, a general method would be appreciated.

  I haven't worked all the details yet but noticed a few things that may be relevant.

  Req AI rate isn't a whole ditch 1E8. It is used to determine the rate of the AO.

  There is no check to ensure that the rate of the AO is an integer division.

  It seems that you have the right idea, but the implementation is not yet there.

  Lynn

• How to increase the rate on windows vista

  my rate to refreash on windows vista needs to increase... looked at solutions and it seems that vista is no longar supported by microsoft can anyone help

  Hello

  Why are you trying to increase the refresh rate? What exactly is the problem?

  You can see the steps in the following article on how to change the refresh rate.

  Flicker of the correct monitor (refresh rate).

  http://Windows.Microsoft.com/en-us/Windows-Vista/correct-monitor-flicker-refresh-rate

• How to get the rate max one sampling NOR 9263 and other cards?

  Hello!

  I'm using a NI 9263 map and a chassis cDAQ-9172 proyect and im he 8.0 whit CVI programming. IM generating a sine and square waves to do some tests on a radio.

  I want my program to be functional for all cards of this type, and we know that most of the cards have different specifications, for example sampling max tariff, in this case the Pentecost of work NI 9263 100 kech. / s as the maximum. IM generating waves based on the sampling frequency.

  If my program must be compatible with most of the cards, my need to program to acquire max sampling rate using a specific function of NIDAQmx.h.

  Do you know if theres a function or attribute that can return this value?

  I tried this function with different attributes, with no results:

  DAQmxGetTimingAttribute (taskHandle, DAQmx_SampQuant_SampPerChan, & MaxSamp);
  DAQmxGetTimingAttribute (taskHandle, DAQmx_SampClk_Rate, & MaxSamp);
  DAQmxGetTimingAttribute (taskHandle, DAQmx_SampQuant_SampPerChan, & MaxSamp);
  DAQmxGetTimingAttribute (taskHandle, DAQmx_SampClk_TimebaseDiv, & MaxSamp);
  DAQmxGetTimingAttribute (taskHandle, DAQmx_SampClk_Timebase_Rate, & MaxSamp);

  The three first atribbutes gives me the rate real samp which is 1Ks/s (according to me, is the rate of samp set to the default value for all cards you before be initialized for the user), but do not give me samp (100Ks/s) max flow.

  The rest of the attributes only gives me the value of the clk, which is 20 MHz and the divisor of the clk (20000). Also I tried with a card 9264 (max samp rate is 25 ksps / s) and the function returns the same results.

  Any idea?

  Thank you!!

  Hey Areg22,

  I think I've found the service you're looking for:

  http://zone.NI.com/reference/en-XX/help/370471W-01/mxcprop/func22c8/

  This link gives just the syntax for the function, but the following gives you more information about the function:

  http://zone.NI.com/reference/en-XX/help/370471W-01/mxcprop/attr22c8/

  When I used the property of this function node output was 100,000 for the NI 9263. Which is consistent with the plug. I would like to know if it works for you.

  Thank you

  -KP

• How to create the weblogic domain model?

  Hello
  
  Need to clean as follows to create the weblogic domain model.
  
  Thanks in advance,
  Come-

  Salvation came
  See if this link helps to WLS 10.x: http://download.oracle.com/docs/cd/E12840_01/common/docs103/tempbuild/index.html. The steps are pretty much same for any area, except for portal area there may be a few extra pots. The best way is first to create a domain using the Config Wizard. Then export this area in a model. Later on different mahcines or same machine, create the areas using this model exported.

  Thank you
  Ravi Jegga

• How to slow the time-lapse video I took?

  Accidentally, I recorded a video using Time lapse video functionality.  How can I slow down the video to view it?

  In addition, he did not record sound when it is in Time lapse mode?

  You do not have. Time is quick, so time happens or is struck by decay more quickly. This audio is not recorded, and it would be completely incomprehensible at the expiration of the speeds.

  Time lapse ignores also usually several frames to expedite the passage of time. So even if slow, most of the data wouldn't be there to see.

• How to disable the back navigation model train adf

  Hello I'm developing a web application tutorial review in which users can take the test, using oracle adf (jdeve11.1.2.4). I have developed a model train that looks like below.

  

  In the picture above inititally user's question 1. Here, he chooses an option then accesses the next train. Value of af: SelectOneRadio will be submitted when it navigates to the next chosen train. This is the default behavior of the model train if am not wrong. Never mind.

  When the user come to back issue 1 the af:SelectOneRadio group is empty because the selected value has already submitted. I have to overcome form this problem. When the user comes back it should be able to see previously selected value. How do I get this declaratively.

  If this is not possible declarative, I have two ideas

  1. when the user come back I don't know what value it previously chosen (as am save this value in a managed bean). So, I have to select by program choice.

  2 user should not be able to navigate back. (This is not a good choice)

  Please help me. How to achieve them. Thank you very much.

  Sorry for the grammatical errors as appropriate.

  Let me put stronger t then, Ruben's. The selectOneRadio stores its value somewhere. When you enter the train, the value is empty and the user does not see a selection. Once he selects a radio selection can be stored in the storage specified by the value property. While this value exists (link or bean), you can navigate back and see the selection. If this is not the case, there is something wrong, for example, you store the value into an object that does not live long enough (scope of application).

  Timo

• How to browse the content 3D model

  Team,

  I work with an IFC file that has been converted to PDF using Tetra4D and I would like to program it to the model using Javascript. The code example below has been modified a little and always returns the error that it cannot find a mesh name in the model. My question concerns the getAnnots3D function. How do I point the function to the bottom inside the model tree to the appropriate level to reach objects (floors of a building) to run my code on:

  initialize() function

  {

  Console.println ("");

  Console.println ("checking to see if the 3D Annotation has been activated again... ») ;

  If (waitingFor3DActivated)

  {

  A3D var = getAnnots3D (0) [0];

  If (a3d.activated)

  {

  waitingFor3DActivated = false;

  Console.println ("... 3D annotation is activated. ») ;

  app.clearInterval (timeout);

  context3D = a3d.context3D;

  layers = context3D.createNewLayersManagerObject ();

  layers.turnOnMessagesInTheConsole ();

  layers.addPartToLayer ("FIRST PLAN of FLOOR", 0);

  This is the error I get:

  * request to add mesh "PLAN FIRST FLOOR" to the layer 0

  * Oops - I can't find a network named "PLAN FIRST FLOOR" to add to the layer 0

  I changed the entry point for the node several times on getAnnots3D of 1-6 like so: getAnnots3D (0) [1]... getAnnots3D (0) [6], but I have had no success running through the 3D model to go far enough down to carry out.

  Thanks for any idea that you can provide and good luck,

  H

  The getAnnots3D parameter is the page number, and it returns a table. If you have a page in the document and that a single 3D annotation, then you use getAnnots3D (0) [0]. He has to work in your case, because the script is to answer.

  JavaScript in Acrobat don't like the names of nodes with spaces. Re-export model with variable-safe names (camelcase, features underscore, etc) and it will work. There is no concept of crossing a 'tree' in JavaScript - each node is a single SceneObjectList - effectively a table - they are just a reference to the parent node if there is one.

  BTW - if you need the layersManager class, do not. 99% of what people want to do with a 3D scene is easier to do in the code base.

• How to remove the pictures of model VM

  After you use the Update Manager to upgrade my models with hardware and vmware tools, I am unable to create a virtual computer from them.  I have seen just from the data store that each model has a snapshot.  I guess that's the reason for not being able to create a virtual machine.  How can I remove these photos?  If I removed them from the data store, this will effect the model or the creation of a new machine virtual?

  I want to be able to remove their so it's not the effect on the models that do a graceful removal.

  Hello.

  See if this discussion is of no help.

  Good luck!

• How to bind the iterator/vo model component?

  Hello
  
  I have a tree in my page template that must be accessible throughout the entire application.
  The application will have hundreds of pages, so it would be pretty boring if we have to redefine the iterator & vo in every single page def.
  
  Is there a way to tie the tree to the definition of the model of the page? Or maybe to other pages inherit def of the template?
  
  Thanks in advance,
  
  Charles.

  Charles,

  Enjoy the Fusion developer's Guide (I assume you are using 11g).

  18.2.1 article talks about how to use data links in a page template.

  John

• How to calculate the rate of data transfer if I know that the total number of samples/s?

  I'm looking to set a PXI system for measurement of County at high speed, routes, while that controlled remotely via MXI - 4.  How can I be sure that the controller is capable of rapid data transfer quite seen the number of channels and frequencies of sampling provided?

  I think I figured this out, but maybe someone can save me.  For the task at hand, I will have a PXI-4496 and four PXI - 6143 s all 32768 samples/s sampling.  4496 is 24-bit, and 6143 is 16-bit.  Thus,.

  bits of samples/s/channel x 24 16 channels x 32768/8 = 1 048 576 bytes / s

  +

  32 x 32768 samples/s/channel x 16 bits/8 channels = 2,097152 bytes/sec

  =

  3 145 728 bytes/s, or exactly 3 MB/s.

• How to control the rate of acquiring data in a while loop

  I'm trying to use a digital trigger to collect data on the rising and falling edge. The design is displayed as below. Now, I save the measured voltage 1 & 2 to the local variable in the while loop. Hoever, the while loop runs at a frequency of more compared to the structure of the case triggered. So I had a lot of repetitive data.  If I record data directly from structure of the case, it will be recorded as data-0-date-0 because of the ongoing case of fake wire.

  I wonder how to revise to save the measured voltage 1 & 2 at the same frequency of up/down edge triggered? Thank you! I have also attached my current version of Labview program, which takes place in time real Labview 2013.

  

  Mcdullna wrote:

  Thank you for the answer. Could you be more specific about the use of the shift register?

  The case of false just past the value through.  With this configuration, you agree that the data remain in the son, avoiding race conditions.  It is also more effective than the use of local variables.

  

• How to get the name of model of the physical network adapter

  I can see the template information for my network via vcenter card, but need help with registration this info for powercli.

  for example, that I'm looking for my request to have this output:
  "Broadcom Corporation NC370i Multifunction Gigabit Server adapt."

  Hello, jstroehmann-

  How about something like:

  ## get the .Net View objects for all of the host systemsGet-View -ViewType HostSystem -Property Name,Config.Network.Pnic,Hardware.PciDevice | %{    ## store pipeline variable for later use    $viewHost = $_    ## for each PhysicalNic on the host, output a bit of info    $viewHost.Config.Network.Pnic | Select @{n="HostName"; e={$viewHost.Name}},Device,MAC,@{n="NicDisplayName"; e={$oPNic = $_; ($viewHost.Hardware.PciDevice | ?{$_.Id -eq $oPNic.Pci}).DeviceName}}} | ft -auto
  

  He catches the .net visualize the object of all the HostSystems, and then displays some info like hostname, VMNic name, its MAC address, then the full name you mentioned.  You could, of course, something with the release other than send it to Format-Table.  How does do for you?

• How to change the text dummy model editable region < head >

  I created an editable in my template < head > so I can add a canonical link and redirect the link to each of the many pages that are based on the template. So I stupidly (I think) added some dummy text to add easier links recorded in each file, and uploaded them. Later, I realized that all my pages have this dummy text in it, what is wrong, of course.

  So I deleted the dummy text in the template and saved, but nothing happened. All them are always this dummy text. So I can't get rid of it in my pages of distance. Why is it not my removal of the dummy text in the collage of the editable area?

  Thank you!

  Editing text or content areas can be changed to a model does not change in the pages of children who have already been created.  Best suggestion would be to copy the dummy text, use find and replace to remove all the files (use search all Site Local), and then load the pages newly published on the server.

  Gary

• How to slow the scrollling title, caption and credits on Movie Maker?

  I need to answer now, I'm in the middle of making my film. The title, caption and credits are so fast, that you can't read what it says. Please help me. Thank you.

  Hi EllenGermany

   

  1. what operating system is installed on the computer?

  2. what version of moviemaker is installed on the computer?

  3. using Windows Live Moviemaker or any previous version of Moviemaker?

  You can see if the link below-
  http://Windows.Microsoft.com/en-us/Windows-Vista/Add-movie-titles-and-credits-in-Windows-Movie-Maker

   

  Also, if you use Windows Live Moviemaker I would recommend checking resources specific to Microsoft Windows Live. Please visit the links below to find a community that will provide the support that ask you in the right direction for applications Windows Live-

  http://windowslivehelp.com/forums.aspx?ForumID=f5dad528-638d-4AD1-BE14-31751f8af98f

  I hope this helps.