How to sync analog & meter and two usb devices

Similar Questions

• How to sync the phone and the phone

  Original title: Samsung Sync ativ with asus laptop

  I try to figure out how to sync my laptop and phone together. I'm not sure that I can get synced but want my photos, contacts, and calendar at least. Verizon told me a way to do it with my email but I could not understand.

  Hi Marissa,

  As you mentioned that you have Microsoft account on phone, I suggest you to connect to the phone using the same account that you use to connect to the laptop and check.

  You can see the steps mentioned in the link for the synchronization between the PC and your phone settings.

  Sync between multiple PC settings

  http://Windows.Microsoft.com/en-CA/Windows-8/sync-settings-PCs

  Please answer us on the State of the question to help you further.

• Two USB devices make Labview hen

  Hello

  I have a system with two cards USB-6221 OEM, connected to the PC on a shared USB cable.  The PC has a Pentium 4 3 GHz with 2 GB Ram under Windows XP Pro SP3.  I build the software LabView 8.2.1.

  Each card USB-6221 is connected to two analog inputs and two entries of quadrature encoders - four each for the entire system.  The plan is ultimately to have independent measurement / data capacity for each pair of analog / encoder for registration.

  Each signal exists as a Global virtual channel in MAX.  I have a VI management of acquisition of data for each map.  Each VI connects two analogue channels for his card in a task and puts each signal encoder into separate tasks.  (I know no other way to bring together them). These three tasks share the same sampling clock.  Trigger is the start of analog input signal.

  Each task has DAQmx read functions to retrieve data at 1 kHz.  The three streams are divided into two identical lines, one for each pair of analog / encoder.  Queues are dealt with elsewhere in the same VI, that recording on the disc as a flag is set.

  The acquisition of two VI is identical, but I ensured that the device settings and channel are different and even the names of internal variable, indicators, etc. are different.  There are a number of global and local variables in use, some accessible by two VI.  There is also a DataSocket link to an external device, where data are read by these and other VI.

  Now the problem.  When two of these VI acquisition work all of the LabView environment slows down a lot.  The PC processor is only 20-30%, there is a lot of available memory, ethernet DataSocket link has a lot of available bandwidth, but the system grinds almost to a halt.  He keeps going, but very slowly.

  With only one (either, no matter which) acquisition ongoing VI, all goes well and I get full speed performance.   Any ideas out there?

  Thank you

  Ian

  Take a look at this http://zone.ni.com/devzone/cda/epd/p/id/192#0requirements it can help you

• Qosmio G30-126: how simultaneously connect analog TV and TV satellite

  Hi, I have a Qosmio G30-126 and you have a problem with receiving simultaneous TV analog (by TV-in the port of integrated TV tuner) and satellite satellite set - top box (by AV-in ports).

  I can't program Windows Media Center for analog TV (but not satellite STB) per port, TV antenna and it works perfectly.
  I can't program Windows Media Center for digital satellite STB (but no TV analog) channels by AV-in port and it works perfectly.
  But I can't program Windows Media Center for the two TV analog I satellite STB, because during programming WMC forces me to choose between analog satellite or cable or SATELLITE box and does not allow me to choose two signal sources.

  For me, it's a big problem, because I have cable (analog) TV and satellite STB with digital channels. And I want to watch all the channels on my Qosmio.
  Could someone help me?

  >... because during the WMC program forces me to choose between analog satellite or cable or SATELLITE box and does not allow me to choose two signal sources.
  I think that in this statement you answered your question. I got Qosmio G30 a long time ago, and I also know that WMC can't handle with two sources of signals at the same time.
  To confirm that contact Microsoft and ask them. I mean that they have designed WMC and know how it works exactly.

  Toshiba has to provide suitable equipment (TV tuner) to provide the TV option on this laptop.

• I get message "USB device not recognized", but two USB devices are actually works very well. Poster sometimes Device Manager 'unknown device', then it will disappear and reappear.

  Poster sometimes Device Manager 'unknown device', then it will disappear and reappear with the error message.  Sometimes, I see the message even when there is nothing in the USB port.

  Hi malsnano,

  I see that usb devices do not work on xp. I'll help you with this problem.

  1. What is the brand and model of the computer?

  2. what security software is installed on the computer?

  3. have you made changes on the computer recently?

  4 is the issue limited to these usb devices?

  Method 1:

  Run the fixit from Microsoft Fixit article and if that helps.

  Hardware devices do not work or are not detected in Windows:

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  M odes 2:

  Put the computer in a clean boot state, then check if that helps.

  How to solve the problem by performing a clean boot state:
  http://support.Microsoft.com/kb/929135

  Note: Once you have completed troubleshooting, perform the steps in step 3: to reset the computer as usual.

  Method 3.

  Run a full scan of the computer with the Microsoft Safety Scanner to make sure that the computer is virus-free.

  Microsoft safety scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx

  Warning of Security Scanner: there could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  Method 4.

  You can disconnect all USB devices and then perform the following steps:

  1. click on start and then click Control Panel.
  2. click on system and Maintenance, click System, and then click Device Manager.
  Note that if control panel is in Classic view, double-click System and then click on Device Manager.
  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.
  3. in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".
  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.
  4. Repeat step 2 to uninstall all items under 'USB Bus controllers'.
  Then, restart the computer and Windows XP will automatically reinstall all USB controllers.

  Let us know if you need assistance with any windows problem. We will be happy to help you.

• How to export pictures to a removable USB device?

  How to export photos to the photo gallery Windows on a removable USB device?

  Windows Photo Gallery as far as I KNOW is just a front-end to your pictures folder.

  In Windows Explorer, open your folder images and copy and paste the pictures that you want to...

• ESX Server guests and Local USB devices

  Is this possible with ESX Server 3.5 to connect to a guest operating system and load a USB device as a card reader connected to your laptop remotely?  How if possible?

  Is there a device that can be installed for the smart card reader, biometric readears, etc.. ??

  To summarize how ESX allows a remote user to plug in a usb device locally and have ESX assign to the team desired vmware instance?

  Thank you and sorry to be so green!

  Green is in fashion now Kyle - get with the program!

  MNANCE152 - doesn't this sound viable, or do you think you will have to take another route?  I'd be interested to hear what you come in the end, if you don't mind me posting it here.

  Good luck!

• How to sync contacts from iMac to iOS devices and air of Matchbox

  Cannot sync contacts between the iMac, macbook air and iOS devices. All with the latest updates.

  Please assoist

  Tony R

  You must explain what stops you to do, and what is your configuration. You have the same iCloud account connected to all devices and Macs? Do you have Contacts enabled in iCloud? Have you tried troubleshooting? If so, what have you tried?

  See you soon,.

  GB

• How do sync you music and android phone?

  I plugged my phone into my computer, put in a cd, ripped the cd on my computer, click on synchronize, dragged from the album I wanted to where he says and he says that their is no connected device. Help, please.

  Hi Aubrey,

  I suggest you try the procedure described in the article and see if it helps.

  Set up a device to sync in Windows Media Player
  http://Windows.Microsoft.com/en-in/Windows7/set-up-a-device-to-sync-in-Windows-Media-Player

  Check out the link for more information.

  Sync manually in Windows Media Player
  http://Windows.Microsoft.com/en-in/Windows7/sync-manually-in-Windows-Media-Player

  Hope this information helps. If you need additional help or information on Windows, I'll be happy to help you.

• How meter and analog value FIFO synchorize

  I use a card NI 6123.

  Anyone knows how to put 6 analog values and the value of the counter in FIFO with the same rate: 4 k.

  Thus, every second, there should be 6 * 4 k analog values and 4 k in FIFO counter value.

  The problem is:

  1. the counter is a numeric value, so I can't put a sampling on it. So how can I put the value of the counter in the FIFO every second of 1/4000

  2. how to sync analog channels and channel meter.

  -------------------------

  DAQmxErrChk (DAQmxCreateTask("",&datHandler));

  DAQmxErrChk (DAQmxCreateAIVoltageChan(datHandler,"Dev1/ai0:5","",DAQmx_Val_Cfg_Default,-5.0,5.0,DAQmx_Val_Volts,NULL));)

  DAQmxErrChk (DAQmxCfgSampClkTiming(datHandler,"",4000,DAQmx_Val_Rising,DAQmx_Val_ContSamps,4000));

  DAQmxErrChk (DAQmxCreateTask("",&ctrHandler));

  DAQmxErrChk (DAQmxCreateCICountEdgesChan(ctrHandler,"Dev1/ctr0","",DAQmx_Val_Rising,0,DAQmx_Val_ExtControlled));

  DAQmxErrChk (DAQmxStartTask (datHandler));

  DAQmxErrChk (DAQmxStartTask (ctrHandler));

  -----------------------------------

  Thank you

  It is possible to apply for a meter in the buffer.  (this is actually preferred).  Simply specify a sampling and source clock.  Given that you want the meter to "lock" data from the meter to the same rate as the sample analog clock to simply specify this sample clock as the sample for the meter clock.

  An example of event in the buffer (life-long) count can be found here by using an external clock (your HAVE sample digital Instruments\NI-DAQ\Examples\MStudioVC2005\Counter\Count Events\CountDigEventsBuffContinuous_ExtClk clock):...\National)

  Check out this example and I think he should get you operational.

• How to synchronize the analog input and the output of two different USB data acquisition boards

  Hi all

  I have two tips very different USB NI USB 6008 case, which I use to acquire the data (analog input) and a USB of NI 9263 is a output analog only site I use to route a signal (in this case a square pulse). The reason why I use the outputs analog 6008 is because I need to deliver negative tension and need the full +/-10 v range.

  Looking at similar positions, I'm pretty sure that I can't use an external trigger or a common clock, I also tried to use the timed synchronization of the structures but no cigar.

  I'm including a quick vi I whipped showing how the jitters because of the lack of synchronization signal. The OD of the 9263 connects to AI in the 6008 in this example.

  I talked to a specialist in the phone and tols me that's not possible.

• synchronize two usb 6289 with a meter

  Hi people!

  I'm trying to synchronize 2 boards of the series M USB-6289 using a counter.

  I searched the forum and that you've already seen the tutorials:

  'Synchronization of series M with LabVIEW and NOR-DAQmx - Developer Zone - National Instruments'

  'Synchronization of data acquisition USB - device to several systems - Developer Zone - National Instruments'

  "The time and the synchronization of the NOR-DAQmx - Developer Zone - National Instruments features."

  However, I still have some doubts (where the post with respect to the following:)

  -If I want to use the meter as trigger for both cards do I need to export to a PFI line and connect to the Member of the Board?

  -I do the same thing with the clock signal (export to the other panel using a PFI line) or using the same frequency for two meters is enough? Or both?

  -can I use the same value for the frequency in the meter and two clocks?

  Hope someone can help out me.

  If possible, underline some examples or detachment would be great.

  Thanks in advance for the help!

  See you soon!

  Hello

  All points depend on what you need to synchronize exactly.

  As you have probably already read in the links you provided, you have the option to share a trigger, or a clock, or both.

  Of course, the best solution is to share together.

  Then, you can choose to directly share the sample of one blade to the other clock (if the two sampling rates are the same), or to move the reference clock, then, both cards will synchronize their sample (with PLL) clock on the same reference clock, as shown in the synchronization M with LabVIEW and NOR-DAQmx series.

  Exactly how you want to use your meter?

  You want to generate a single trigger pulse?

  Then, for examples of synchronization, there are some zip files at the end of the links that you have read.

  Kind regards

• 6071E analog out and trigger to the end

  Hi, I'm here a trivial question: using PCI6071E, at the end of an analog output, is it possible for a trigger to output or update a number line?  for example, we hope when the last MONOSTABLE one sample is done, a digital HIGH is generated to power a switch.  I can think of have an analog and digital task task and the digital task at the end of an analog task in the program, but I don't know how long the delay would be. The best ways to do this? Thank you!

  Analog output: finished/large size but NOT via the trigger of FIFO, internal CLK software,

  on DAQmx / C + c++ / WinXP

  eLions,

  Analog task followed by a digital task that you thought would work, but it would be a delay of small software timed as you thought it would which can cause problems. If it's an analog output of finite size (say 1000 samples), what you can do is to synchronize the digital and analogue tasks together and have a digital low for 1000 samples, with the 1001eme exit on the digital line being the maximum. It would make no delay, as analog and digital line should be sharing the same frequency. C++ examples provided show how to sync analog analog output, which can be changed by the digital output.

• Two USB microphones on a computer = a track, two voices... right?

  Hey everybody,

  I apologize for my ignorance, but I have a long list of things to learn about technology, and I learned a lot about computer specifications and features, so I went a little bit. I just finished a list of parts for a custom version, and once this is done, I need to establish a method for the monitoring of sound. I saw on a few threads here that you cannot build two microphones mapped onto a separate track each unless you use a pre microphone or mixer with multiple microphone inputs... and it's unfortunate, because, after spending more than $1 k for the computer, I'm not really willing to spend hundreds more on an intermediate device , microphones, stands, pop filters AND cables. Other than the microphone preamp, it's at least two of everything, and it will get expensive fast.

  So... If I use two USB microphones on a computer with Adobe hearing, then the voice of every microphone will be record for a single track, correct? If I wanted to change the voice, I have to go until then individual time during the track instead of referring to, say, "A track to voice A" or "Track B voice B," right?

  House777 wrote:

  So... If I use two USB microphones on a computer with Adobe hearing, then the voice of every microphone will be record for a single track, correct? If I wanted to change the voice, I have to go until then individual time during the track instead of referring to, say, "A track to voice A" or "Track B voice B," right?

  Not much, so no chance to work at all, I'm afraid. Most people have a little trouble to make a USB microphone is working correctly, and I'm not aware of that anyone ever get both working at the same time. I'm not saying that this is absolutely impossible, but there is a good chance they are.

  The problem is that the hearing is focused on the ASIO, and Steinberg (who invented) have determined that because he hits his way in the OS to give you better performance of latency, you can only use one device at a time. And your USB microphone is a device. There is just an outside possibility using ASIO4ALL you can aggregate two USB devices I have the feeling that there is something else that could stop this work - these devices are very slippery, and pilots with them generally aren't much anyway. So you can try it if you want - but I think you would be wasting money. And above all that, you'd have no supervision available (limited to a new device), or if you purchased a USB microphone with a headphone jack on it, you would very quickly find embarrassing how what is...

  Which brings me to:

  After spending more than 1 k $ for the construction of the computer, I'm not really willing to spend hundreds more on microphones, an intermediate device, pop filters, stands, AND cables. Other than the microphone preamp, it's at least two of everything, and it will get expensive fast.

  To start, you can buy pop and stands filters independently, so it isn't in the equation. Cables really are not expensive (especially if you learn to do it yourself), and there are a number of mixers small enough at a great price with links of USB, and which also provide the replay and monitoring. For example, if you have purchased a Behringer Eurorack UB802, you could pan each microphone on the side of the stereo, and it would let you separate them. It's simple for this divided into a pair of mono channels, so that you can edit them separately if you wish.

  And your overall cost is going to be very similar. USB microphones is more expensive than their equivalents not USB, and something like the Behringer will make the difference. So for a similar expense, you will get a system that works, more viable output and some monitoring available. I would say it was a mistake, myself.

• I cut a record and stuck to a usb device. I want to restore the folder on my computer

  I cut a record and stuck to a usb device. When I tried to open it, he couldn't. I want to restore the folder on my computer. I know there is a way to restore your computer in the last days, but can't remember how. Does anyone know how to do this? This is a very important video of my children.

  System Restore does NOT monitor and restore user data.  You cannot use the system restore to recover a folder deleted from videos created by the user.

  What is the error message you get when you try to open the file on the USB flash drive?  Please do not paraphrase.

  What version of Windows you have, including the service pack?  Do right click my computer and select Properties, if you are not sure.

  In the future, copy and paste files to and from USB devices rather cut and paste or 'move '.  Only delete the original after that you know that the copy is used.