HP 2710 m monitor connected to two computers

Similar Questions

• Try to set up a direct parallel connection between two computers in Windows XP Home edition

  I tried to set up a direct parallel connection between two computers in Windows XP. I have the right cable (CAT 5 Ethernet connection) and you can set up the connection on my own laptop, but when I go through the installer on another laptop it create new connection-establishment of advanced connection--> when the next window opens asking me to choose between "accept incoming connections" and "connect directly to another computer" (which I need to select) for the second option is grayed out and not can not be selected.

  The same thing happens when I try to implement the same connection between my laptop and the desktop we have. All of these computers are running on Windows XP service pack 2. I really need help with this because I'm about to start pulling my hair.

  Any help would be very, very, much appreciated.
  Thank you

  Hello

  Check it please this subject http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=3423&messageID=11170

  I hope this will help you.

• How to configure a direct cable connection between two computers in Windows 7

  Hello

  I'm trying to set up a connection by serial cable with serial cable RS232 DB9 female-female between 2 PCs, one with Windows 7 and Windows 8.
  
  For the initial check of the cable, I used a terminal program such as HyperTerminal, PuTTY, RealTerm. But none of the PC was able to read/write data from the port. I shorted her transmit and receive pins (2 & 3) at one end with a jumper (PIN stapler) for a loop to return the data to the Terminal. Terminal exits each letter typed twice, that is to say the cable and the COM port works correctly for two computers. But with 2 PCs connected, the Hyperterminal does not output nothing written of another PC Hyperterminal.
  Possible suspects: -.
  1. in the device-> PORTS (COM and LPT) Manager - there are 3 elements in both PC
  Communication Port (COM1), Communications Port (COM2), the Printer Port (LPT1).
  while I plug / unplug the cable at the PC, nothing changes in this section.
  2. the drivers for this type of cable to not installed.
  3. different OS installed on the PC.
  4 or I have to create a new connection , and then connect directly to another computer as mentioned in http://support.microsoft.com/kb/305621/en-us . But I didn't know how to do these steps in Windows 7/8.
  Any idea about this problem is appreciated.

  The problem is your trying to use both ports 'exit' to connect two computers / never going to work.

  VGA ports are for v's t. 'If' they are able to c.p.. otherwise, you will need to use a HDMI to the TV which is also an exit from the c.p.

  If you notice your computer and your monitor using a DVI port connection not a VGA.

  And no you can not use a DVI cable either :)

• is it possible to establish a direct connection between two computers, one running on windows xp sp2 and other running on windows xp sp3?

  Hello
  I connected two computers, one running on windows xp sp2 and others running on windows xp sp3 via com using RS232 port via link Modem DFM-562E ++.
  I am able to dial numbers from a PC successfully.
  But when I do a direct link between them (one as a host, the other guest) through the com port, I get error 777.
  Is this because the two PC's using different service packs?
  Help, please.
  Thank you & best regards
  Ravi

  It is not the service pack - although you should have installed sp3 now.

  Your message is not clear: have you been able to connect successfully computers using your modem D-Link?  How did you do that?  Will there be a modem in the second computer?

  What cable are you using to establish a direct connection between the com ports on both computers?  If you have purchased this cable online, please provide a link to the site where you bought it.

  Please describe the physical connection between the two computers.  For example, this is how you connect to the Internet by dial-up services:

  computer 1-{(9 broches) RS-232 serial port}-{RS-232 cable supplied with the modem}-{modem}-{phone cord (RJ-11 modular plugs at each end)}-{telephone wall jack}

• Warning: you are connected to two computers.

  I was working in my account to windows live hotmail and when I tried to open an email (at least, I think that's what I was doing at the time).  I got a pop up message that says I was logged into two computers and my email was not available and I have to refresh the page, I did.

  My question is: this message really means that someone else somewhere else was connected to my email?

  Hotmail forums:

  http://www.windowslivehelp.com/forums.aspx?ProductID=1

  They will help you when repost you your question in the Forums above for Hotmail.

  See you soon.

  Mick Murphy - Microsoft partner

• How to stop the connectivity between two computers that use the same IP address... ?

  Today, I managed to connect two computers with the same IP address. But now it is to be feared. for example, a person can access my computers using my IP and MAC address. So now, how can I stop the connectivity between these two computers. should what setting I use to stop.

  Tahnks.

  Hello

  1 have. what measures you taken to connect 2 computers with the same IP address?

  2. How are the 2 computers connected?

  3. how exactly you want to stop the connectivity between 2 computers?

  I want to tell you that 2 computers on the same network cannot have the same address. Each machine must have a unique address to identify it. A private network, as a home network connected to the internet, can be connected to a router to connect to the network, will have only 1 address, public IP address.

  In addition, if we know the IP address of a computer along the user ID and password, we can access the computer/shared files.

   
  If you are referring to the change of the IP address of the two computers, you can follow these steps and check.
   
  a. network connections open. Click the Start button, and then click Control Panel. In the search box, type 'adapter' and then, under center network and sharing, click view network connections.
  b. right click on the connection you want to change. Click on properties. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  c. click on the network tab. Under this connection uses the following items, click Internet Protocol Version 4 (TCP/IPv4) or Internet Protocol Version 6 (TCP/IPv6), and then click the properties button. To specify your IP for IPv4, click on use the following IP address, and then, at the address IP, subnet mask, and gateway boxes by default, type IP address settings.
   
  A typical IPv4 address looks like 192.168.0.2; a typical subnet mask is 255.255.255.0. The default gateway is usually the address of your router.
  For example, IP address: 192.168.0.2 by 192.168.0.12 (for computers)
  Subnet mask: 255.255.255.0
  DNS: 192.168.0.1
   

  I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.

• Creating cloud incorrectly stating that I am connected on two computers

  I am connected to creative cloud on a single computer, and when I try to connect on another told me I am already connected to a maximum of two computers. Please someone answer could Adobe for this as soon as possible, or give me contact information for support CC?

  Chat now button down for the Activation and the deactivation of the problems can help

  http://helpx.Adobe.com/x-productkb/policy-pricing/activation-deactivation-products.html

  or

  Remove the license on a computer http://forums.adobe.com/thread/1442423?tstart=0

  -http://helpx.adobe.com/x-productkb/policy-pricing/error-maxium-acitvation-exceeded.html

• Problem with the connection of two computers with windows7 to internet at the same time with wrt110

  Me and my friend have two windows7 installed on our computers.

  If one connects to the internet via a WRT110 wireless router it goes without any problems.

  But if we both try to connect to the internet at the same time, it does not connect.

  Can anyone help?

  You can try the upgrade/flashing the firmware on the router... Download the firmware from www.linksys.com/downloads and save it on the desktop... Opening of session in the Linksys GUI and click on the Administration tab... Click on the "firmware upgrade" sub-tab and choose the correct .bin file... click on upgrade... Wait a few seconds until it shows that "the update is successful," after the upgrade of the firmware, click on "Reboot" and you will be returned to the same page OR it will say 'cannot display the Page.

  Now, hold down the button to reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

• How to share internet connection between two computers (win7 & win XP)?

  "I plan to get cable internet connection ADSL broadband." And again, I want to share internet from one computer to another. »
  

  • But I have a question in mind which is lower.

  Before going to answer my Question Please read two notes point-
  
  Note:

  A. very important don't ask me what I have installed and what equipment I have in my PC? just give me a simple, easy answer. guess I'm no networking and I have two PCs. You teach me from scratch.

  B. do not use the more technical term. I hate it when someone using the most incredible technical term (its towers the response in the largest number of questions lol). just give me a simple answer.

  If you are eligible to condition or except my EULA :) go further and read my questions give me an answer simple and straight.

  Now please read the question below.

  Issues related to the:

  Q1. Which computer should I connect main internet connection (computer on which will better host win7 or Win XP)?
  
  Q2. What equipment I mean as a router, hub, NIC etc.? Please specify if these materials will be required for two PCs or for one.
  
  Q3. What type of Internet connection sharing will be better to be wired or wireless (cost, speed and security wise)?

  Q4. I need two IP address both part of connection to the internet between two PCs?

  Thanks in advance.

  Hi Zeff,

  You can make Windows 7 the main computer for internet connection and then host the Windows XP computer.

  For more information, see the article:

  Start here to set up a home network in Windows 7

  Networking of computers running different versions of Windows

  With respect to the equipment as a router, hub, NIC depend on the connection (wired or wireless) you want to use. You can also check with the ISP (Internet Service Provider) for more information.

  For more information, see the articles:

  What do I need to connect to the Internet?

  Setting up a network home

  Wired and wireless connections have great benefits, but they have also some disadvantages.

  Wired connection:

  > Faster and more robust than wireless connections but not so flexible when positioning of computers and devices because you must be connected to your Super Hub with an Ethernet cable.

  > Safer than wireless connections, but not so convenient for users of laptops and other mobile devices.

  WiFi connection:

  > Wireless! If you can connect when you want. However performance may be affected by walls, electric interference etc.

  > Ideal for users of laptops and other mobile devices, you can connect devices more but slower than wired connections

  > Very safe when used with higher level (WPA) encryption. You can connect your smart phone to your network wirelessly for faster browsing.

  However, unauthorized users could try to use your connection (which explains why security is so important).

  There are two types of IP addresses. external and internal. Both computers have the same external IP address but separate internal IP addresses. Each device in your network will have its own (internal) IP address. The external IP address, who sees the Internet is actually assigned to your router.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• Cable connection between two computers in Windows XP

  Hello

  I want to set up a direct connection cable between 2 computers on Windows XP. Please, help me in this issue.
  Thabks

  Hello

  There is a guide on your problem, check it:

  http://support.Microsoft.com/kb/305621

• My printer is connected to two computers. I find that the second computer does not print unless the first computer is also on. Can I get every computer to print without the two be on?

  the printer has been first on windows 7 and second on windows xp, because that's the way I was told iy had to be done. But I thought that each computer can print separeately withou t windows 7 being on.

  Hello

  1. How is the printer connected? This printer is on a network?
  2. this configuration was already working before?

  You must configure a print server. If your printer is a network printer, you can connect it to a router, and all computers connected to this router can use the printer individually. If the printer is not a network printer, you can buy the equipment to turn it into one.

  See the articles below for more information:
  http://support.Microsoft.com/kb/308028
  http://TechNet.Microsoft.com/en-us/library/bb457001.aspx

  I hope this helps.

• Share Internet connection between two computers

  I have a laptop running Windows Vista Ultimate 32 - bit and a desktop computer running Windows XP Professional 32-bit. Both have the latest service packs. The laptop is connected to my WiFi and I need to share it via ethernet. I could just use Connectify but I don't feel like it. What is the best way to share?

  If the office is not close enough to get a cable (or you don't want to drill through walls), buy a wifi USB adapter for the office.

  If it is close enough to run a cable but the whole of the Ethernet ports on the router are used, buy an inexpensive Ethernet switch.

• can connect you two computers so you can see other people screen

  to be able to see the thing on other computers

  Yes, remote assistance. If you and the person you want to show your screen to have msn, there is a button to request remote assistance tab actions in a message window, it would be the easiest method to use. If not, you can just use it (it should already be on your computer), but the receiving person will activate in the properties of the system, and when you start, you will need to send the key to get.

  The msn is much easier.

  Note that this is a thing in a way, you will see their screen or vice versa, you don't see each other screen at the same time. Because that would be stupid. You would see their screen and on their screen... is your screen!

• A direct network connection between two computers of W7 SP1 64-bit to copy files without network?

  Hello.

  Is - this transfer copy machines a lot of large files between two updates 64-bit SP1 W7 (Enterprise and Home Premium) with a regular network cable without a network?

  Thank you in advance. :)

  If it doesn't, you may need an adapter inverter. Like this

• I have a one year subscription to photoshop, previously I had downloaded on an old computer. Now, I have a Mac and install it. But he said: I am already connected on two computers. I've marked the place for me in unlog on those, but it's just if

  I need assistance with unlogging from other computers.

  Hello

  Please see Document below: -.

  https://helpx.Adobe.com/x-productkb/policy-pricing/error-maxium-acitvation-exceeded.html

  Hope that answers your query.