HP 550 wireless and Bluetooth problem on win 7

Similar Questions

• Turn on wireless and Bluetooth problem

  Hi, I bought HP Paviion 14-V040tx

  I installed laptop with windows 7 and install all drivers

  I have a problem to turn on wi - fi or bluetooth, no indicator or notice when I press the F12 key

  Hello:

  Your laptop uses the Broadcom BCM43142 802.11bgn 1 x 1 Wi - Fi and Bluetooth 4.0 HMC combination WLAN adapter.

  Have you installed these two drivers?  These should be the ones you need...

  Wireless:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-137998-1&cc=us&DLC=en&LC=en&OS=4063&product=7234477&sw_lang=

  Bluetooth:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-137999-1&cc=us&DLC=en&LC=en&OS=4063&product=7234477&sw_lang=

• Pavilion G6-2005ax, cannot install drivers wireless and bluetooth problem.

  Hello, I installed windows 7 ultimate 64-bit on my HP Pavilion G6 2005ax after formatting. I downloaded and installed all my drivers from here . But '2011 Ralink 802.11 b/g/n WiFi Adapter "and"Ralink 802.11 b/g/n Wireless LAN Adapter Driver "doesn't install. There are yellow symbol on "Network controllers" in Device Manager. I could succcessfully install the bluetooth driver but I can't find any device, or it gets discovered. Please help someone. Thank you.

  Hello:

  Depending on the hardware ID will keep you (USB\VID_0CF3 & PID_311D & REV_0001), that decodes an Atheros bluetooth radio.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5060880&prodNameId=5060882&swEnvOID=4059&swLang=13&taskId=135&swItem=ob-101447-1&mode=3

  Paul

• Satellite Pro S300: Command wireless and Bluetooth and save this config

  Hello

  In the normal state, I want to have active bluetooth and the wireless off (it would be good if it can be activated by pressing Fn + F8)

  Problem: Every time is turn on the laptop (or reboot), the without wire is activated and not the bluetooth. So I have to press Fn + F8 to turn off Wireless (which turns off wireless and bluetooth) and then press Fn + F8 to select bluetooth to activate bluetooth. How can I save this config?

  Thank you

  Hello

  Unfortunately, it of not possible to save these settings.
  But as far as I know that the settings should not change after a reboot of the laptop.

  But you can check the Bluetooth settings in the folder utilities Toshiba.
  There is a general named tab that contains a few options.
  Check this box

• 15 HP r015dx Notebook: 15 HP r015dx - wireless and Bluetooth controller driver

  Hello. I have a HP 15 laptop r015dx. I've just recently demoted it to Windows 7 Professional 64 bit window 10. I installed most of the necessary drivers except for the wireless and Bluetooth. I search all the possibilities to find a driver for my laptop and was unsuccessful. I read an article Solve: pilot Wifi HP 15-d006tu Windows 7 64 bit where Paul Tikkanen brought a solution to the person who has had a similar problem.

  Does anyone in this forum can give a solution to this problem that I am facing.

  Need help... AS SOON AS POSSIBLE

  Bill

  Hi, Bill:

  That's exactly what I need.  Yes, you have a different wlan with bluetooth card that showed the parts list.

  Here are the links to the wireless and bluetooth drivers you need for this model of the wlan card.

  This package contains the installation package driver for Ralink wireless LAN controllers in the laptop models running a supported operating system.

  FTP://ftp.HP.com/pub/SoftPaq/sp71501-72000/sp71525.exe

  This package contains the installation package driver for the Bluetooth MediaTek/Ralink in the laptop models running a supported operating system.

  FTP://ftp.HP.com/pub/SoftPaq/sp70501-71000/sp70570.exe

• How can I turn off wireless and bluetooth via the bios?

  "How to turn off the Wi - Fi in bios maps?

             

  I have a laptop Toshiba and Windows 7.

  Some specifications are necessary for me to work on a remote network. Bluetooth and Belarc test still does not work and I get the message"wireless cards must be disabled in the bios. »

  Without thread is DISABLED in the BIOS, also, I went to the network and the Internet and chose WIRELESS DISABLED ON HARD WIRED CONNECT and network cards, I DISABLED it. Also, I went to the network and sharing Center and changed the settings of the adapter to DISABLE.

  Wireless Configuration Utility > Broadcom Wireless Utility > "No currently no wireless available and active devices."

  Bluetooth is UNINSTALLED

  What else can I possibly? I would appreciate a solution.

  Thank you

  GVautour

  Hello

  Thanks for posting your query in Microsoft Community.

  You want to turn off wireless and Bluetooth via the BIOS, I suggest you ask to contact the manufacturer of the computer for that.

  Please do not hesitate to post, if you face problems with Windows in the future, we will be happy to help you.

• Y at - it Windows 7 drivers for this wireless and bluetooth device?

  Have a DELL XPS 8700 with the following wireless and bluetooth chipset/map:

  Intel wireless Bluetooth 4.0 + HS adapter

  Intel Dual Band Wireless - AC 7260

  Are there drivers for Windows 7 64 bit for this chipset? Reason why I asked was when I tried to get DELL to install Windows 7 Pro instead of the Windows 8.1 on my machine, their excuse was that there were no drivers for these 2 items in Windows 7. I do not quite believe them.

  Having someone here "converted" Windows 8.1 (not pro) for Windows 7 and you have the mentioned chipset here?

  The guide says:

  The schema partition and target system type set as default system BIOS or UEFI computers MBR partition and can be used in most cases.

  In the rare cases where you need to install on a 3 to or more large drive with a SecureBoot/UEFI BIOS select GPT partition system for UEFI computers (I have not tested).

  So, if I did not need to install Windows 7 on a 3 TB drive, it will be better to disable the secure boot and UEFI to legacy? Or do I only in order to disable secure startup, but the setting UEFI?

  Reason why I ask, is that the other installation of Windows 7 guides you need to disable these two parameters, but in the guide you sendt me it seems that the only thing I should maybe change the start setting secure. Or maybe not?

• GPS, Wifi and Bluetooth problems

  So I have an iPhone 6 running on IOS 9.3.4 and have had problems with the GPS and the strength of wifi connectivity and bluetooth for a while now.

  First of all, the GPS.  It does not work.  When I run the maps or google maps on my device and the input an address the app can give me a written plan, location, but will not show me on a map.  He'll start road to everywhere where I go and tell me to start position, for example, to the North on the road on that I am, but the arrow does not follow me and tell me when the turn or where I am.  Occasionally, he has a message of guidance down with a spinning wheel and then, after a few seconds, disappears.  I tried to reboot my device several times, I have reset the network setting, I reset all of the settings, I backed up my phone, reset it and recovered save him.  Nothing has worked.  I was at my local verizon store and received a 'new' (its definitely refurbished) phone and the problem persists on the new phone.  I reset the phone to factory setting without content, set up as a new phone and tried the cards again, thinking it might be a problem with the back to the top.  It still does not work.  I'm perplexed right now and do not know what to do/try.

  Second, wifi and bluetooth connectivity is terrible.  I can only receive a wireless signal so that in very close proximity with the router.  I tried to different houses/companies and it is the same question.  However, bluetooth is just as bad.  I use headphones wireless, and go to the gym/go for the route with them.  I used to be able to walk around the gym without my phone and have connected the headphones, but now I can't have my phone 2 feet of the appliance without the music being agitated (bad connection).  I'm really irritated that I cannot understand this point and that he can't seem to find a fixed solution online.

  If you have just updated to iOS 9.3.4, which I didn't even know still shone, so maybe it's a bug that comes with the update. However, your problems seem to follow a trend, you can not far from a source of connection and now a signal. It is perhaps because the necessary components for the Bluetooth, GPS and WiFi signal are damaged or defective. Have you dropped or spilled liquid on your iPhone recently?

• Wireless and LAN problem with Thinkpad

  Im having serious problems with my Thinkpad T61p on my wireless and LAN drivers (at least I think it is the drivers, could be something else). This can be a long explanation, but please bear with me.

  Yesterday, after seeing an example on the net, I tried to connect my xbox 360 to my laptop. I thought I'd be able to play on the xbox wireless using the laptop as a gateway to my router. I never had any problems before with logins, and had the wireless on my home network.

  After plugging in an Ethernet cable into the laptop and xbox (following the instructions, I had online), I became "Network connections", (start-> Control Panel-> network connections). I had used a cable to connect your desktop to my laptop before and normally when you go to network connections, the connection between them appears as an icon. This time, has no icon.

  I decided to try and create a connection. At this point my wireless was still working because I was always browsing the net. On the left sidebar, I clicked on "create a new connection". Hit next, and then click the radio button "set up an advanced connection." "Accept inbound connections" option box pressed, the next button. Finally, a link has been created, but when I went to go again my wireless connection dropped. I went back and removed the link to "network connections".

  I opened "Logins" and tried to connect to my home profile. No results. I tried clicking on 'Search' to see were there any other networks available and all I kept getting was: "the wireless radio is turned off. You want to turn on? ". Press 'Yes', landmark of waiting a few seconds, click on 'Search' again, same message. No matter what I did, I couldn't get the wireless to turn on. So I found this thread:

  http://forums.Lenovo.com/LNV/board/message?board.ID=T_Series_Thinkpads&thread.ID=3314&view=by_date_a...

  and decided it was best to update access connections. It came as a default as version 4.42 so I updated to 5.12. Rebooted and tried again. Now the wireless starts up fine, but when I look for my router connections, some networks are located.

  Next to this thread:

  http://forums.Lenovo.com/LNV/board/message?board.ID=Special_Interest_Utilities&thread.ID=524

  I updated my drivers and countless other things without success. I've updated wireless drivers from this page and dial-up connections to:

  http://www-307.IBM.com/PC/support/site.WSS/document.do?sitestyle=Lenovo&lndocid=MIGR-67853#wireless

  Another strange thing I see is that when I try to 'Create a new connection' 'Network connections', select 'Create a home or small business network', keep the progression through each other, it is to choose connections it is said that both my wireless and LAN are disconnected.

  Wireless that I use is: Intel Wireless WiFi Link 4965AG

  LAN: Intel 82566MM Gigabit Network Connection

  It is not to have problems in Device Manager and that these two are enabled.

  Does anyone have an idea of what is after occurrence and how I could fix this? Any help is greatly appreciated, because I need it for work soon.

  It sets obtained.

  Essentially had to uninstall the network drivers (not enough I know) from Device Manager and reboot. After the wireless and LAN is back!

• Configuration wireless and Bluetooth on HP Pavilion p050sq-15 Notebook PC

  Hello, I just bought a laptop computer (Pavilion 15-p050sq). I am using windows 7 ultimate x 64.

  I want bluetooth and wireless drivers for my laptop.

  And a second question is, wich turn wireless button or wich order fast for example fn + f12 (btw it does not work)

  I need help to set up the wireless network...

  Sorry for my English guys...

  Hello:

  Here are links to the drivers you need...

  Wireless:

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdDetails/?spf_p.TPST=swdMain&s...

  Bluetooth:

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdDetails/?sp4ts.Oid=5405371&SP...

  SM Bus controller:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-131822-1&cc=us&DLC=en&LC=en&OS=4063&product=7265072&sw_lang=

  PCI Simple Communications controller:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-131838-1&cc=us&DLC=en&LC=en&OS=4063&product=7265072&sw_lang=

  ACPI\HPQ6007:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-137939-1&cc=us&DLC=en&LC=en&OS=4063&product=7265072&sw_lang=

  ACPI\INT33A0:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-131840-1&cc=us&DLC=en&LC=en&OS=4063&product=7265072&sw_lang=

• Compaq Presario CQ43 - 206TU Action key and bluetooth problem

  Hello

  I have a Compaq Presario CQ43-206TU to fix here and ive some problems that I had to reinstall windows 7 x 86 and the first problem is the work of dosent FN key at all. Ive installed the tool recommended HP without effect.

  The second thing is dosent it driver Bluetooth install well watch upward with the error in Device Manager.

  one thing I did prior to the relocation is an update of the bios to version F37, but there is also no setting for Bluetooth or shortcut keys to activate.

  Before the bios updated and the reinstall the wifi led on the keyboard was red and now its red until windows starts and that it turns white. The FN key worked before as well.

  How can I get that all the work?

  glopp1

  Ive solved the problem. I had to disable the key mode in the bios and it worked after. Bluetooth is another problem windows update installed a new driver who caused problems after a reinstall of windows (just delete driver has not worked for me) and by the use of hp, it worked.

  http://support.HP.com/us-en/document/c02035108

  glopp1

• 2.4 GHz Wireless and the problem of USB 3.0 with WRT1900ACS

  Hi people

  I guess I discovered a new "buggy" feature on my new ultra buggy router.

  When I plug my WD mybook external hard drive usb 3.0 on the slot usb 3.0 on the Router 2.4 GHz and 2.4 GHz-comments off immediately. When I unplung the hard drive the 2.4 GHz re - started working properly, but after 3 times this operation, I have to restart my router with the cause of usb 3.0 unplugged the 2.4 GHz band stops to work control. (also tried with different readers)

  On the 2.0/sATA port everything works fine, but I bought this router for sharing an external hard drive connected to the router quick installation network data (and on this side, this router is amazing > 100 MB/sec in reading from the hard drive to the usb 3.0 port).

  This happens with the firmwares both 1.0.0.169041 and 1.0.0.168229.

  I also tried to put all possible combinations in the settings Wireless 2.4 GHz.

  All wired connections work properly since I bought it.

  If I can't solve this problem in 1 week I will change this router, bought on amazon, with an ASUS or a Netgear, may be less effective on the side of drive hard usb 3.0, but probably more stable than this one.

  It seems to me that Belkin doesn't care for anything about its customers, they do not work hard to solve the problems on these router, otherwise there is no other router but WRT1900AC v1 with a stable firmware. Instead, the company retains to launch the new hw updates each year. Belkin will never reach the success of the WRT54G in following this path.

  The speed of USB3.0 data transfer causes intereferences with the frequency of 2.4 GHz WLAN.

  Make sure that you use a USB 3.0 cable tank of high quality when connecting any device to the USB 3.0 port.

• bthmodem.sys and Bluetooth problem

  I'm having a problem with my bluetooth on my laptop.  He told me to press Fn + F2 to turn on, but it does not work. I look at my system, and it does not appear under devices. It is as if it does not recognize. I also looked under my system drivers and noticed that windows as disabled for some reason any.  How can I reactivate bthmodem.sys and get my bluetooth works again?

  Hello

  I suggest you try to execute this fixit and see if it helps:
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-Bluetooth-enabled-devices

  It will be useful.

• Pavilion DV5-1118es wireless and Bluetooth issues!

  I have a Pavilion DV5-1118es am not able set and activate wireless & Bluetooth, can someone help me to do these things?

  @smhsn

  Hello

  Your model is without bluetooth.

  You can check the specs here.

• Network wireless and Bluetooth card no longer works...

  Hello

  I guess I did something very stupid.

  I had an Ideapad s12 via nano 2959. While the closure of Windows XP, I turned off the wireless switch. After reboot I lit it again once, the blue icon, the white light on the front edge of the dark rest netbook and wireless, nor the network card or the bluretooth seems to work more. The bluetooth of the systray icon displays in blue and Red instead of blue and white. Wireless systray icon as not connected, a scan of wireless networks you find no.

  In Device Manager, I'll see under "Bluetooth-devices" only "-Bluetooth enumerator. I don't see anything in the enumerator "Bluetooth."

  While I find the adapter wireless network installed, enabled and working properly...

  Didn't destroy my wireless devices by cutting so that the closing...?

  If so, why the adapter wireless network will show as being installed, active and functioning correctly in Device Manager?

  Hello and welcome check the Menu Fn + F5 softswitch...

  cordially KalvinKlein