HP 6005 Pro SFF: installation of three monitors on 6005 Pro SFF

Similar Questions

• After a clean install of Windows 8, I can't get three monitors to work

  I did a clean install of Windows 8 pro.  I have a Dell T1500 with over-pants V4800 graphics.  This machine previously had Windows 7 installed and works with the ATI driver.  With Windows 7, the three monitors worked without problem.  Now, with Windows 8 installed I can't get two monitors to work.  I use the more updated driver for Windows 8 for the map on the website of AMD.  The third monitor can be seen on the page of the screen resolution, but I cannot "extend desktop...". "the third arch.  When I try to do so it gives me a message saying

  "The display settings could not be saved.  Please try another combination of display settings. »

  All three monitors are the same, Dell P2210.  I tried different resolutions. I tried the driver I was using on Windows 7, I uninstalled the driver and adapter repeatedly.  I installed all the drivers from AMD with the extras (hydravision, etc.).  I used just the default Windows drivers. I have change the placement of the monitors on the video card, but few matter where I plug them in, only two works.  All monitors are operational.  I even tried different monitors.  All this with no result.  I tried to use the Catalyst Control Center.  He sees the third monitor but just shows it as being disabled with no way to enable that I see from in the Catalyst Control Center.

  It is the last obstacle for me to fully use this machine to Windows 8.  I'm puzzled.  I have read many other forums.  I've heard of this problem with Windows 7 as well so I don't know that it's specific to 8 but could very well be.  Yet once I had Windows 7 with three monitors with the same card.  Contribution to this issue would be greatly appreciated.

  I had this problem on a Lenovo three installation of the monitor using the integrated display laptop, a monitor outside the mini HDMI and a third follow out of the HDMI Port among Replicator.

  In the end, it's a simple solution.  When you go to display settings, all three monitors not reimbursed up to 1920 x 1080 and configuration could never be saved - however the 3rd monitor only supported by 1680 x 1050, which is the resolution (recommended).  After changing the 3rd monitor for the resolution recommended, I was able to save the configuration to display > screen without problem resolution.

  I don't know why the resolution not supported has been set default to-after selecting the right pair, there is now no option to go to the highest resolution not supported on this screen.

• XPS 12 + two S2340T for three monitors have contact problems

  I am testing a configuration of business as part of our R & D in the field.  I'm running a Dell XPS 12 8.1 Windows.  Last week, I ordered two external monitors S2340T for use with my setup.  In the past, I was able to successfully run the two external monitors for a three monitor Setup.  When I plugged in the first S2340T, everything worked fine. When I connect the other, I lost the ability to screen on the first.  On the second, when I touched the screen, he was interacting as if I touch the screen of the PC clean, despite the fact that he was it running correctly as extended desktop. I finally found that each monitor must be running with the USB cable (I found this in a forum of the year, even if the instructions I received still makes no mention of the need.) At the moment I touch on the screen of Mobile PC, as well as the first S2340T (monitor 1) that I am connected.  The other I'm connected (screen 2) takes any action contact and is the space in the mobile PC display.  If I disconnect 1 monitor, monitor 2 will work perfectly, as expected.  If I plug then 1 monitor, it won't work properly, allowing a contact immediately to show as a touch control on the laptop PC screen (thus imitating the question I had when monitors were reversed). I completely replaced the Dell drivers, even those it says is up-to-date.  I've disabled and upgraded.  At this point, I don't know what to try next.  Dell has recently told me to update my Bluetooth driver for a separate issue and immediately after, I lost the Bluetooth connectivity option and my Bluetooth mouse functionality. After you run an update of the driver from Dell, I lost my Bluetooth receiver on the laptop.  Fortunately, I've seen it before and all I have to do is to re - install the VPN we use SonicWall Global VPN client software.  Restart the system and my Bluetooth is back; but now neither monitor reacts to the touch on the scree, each monitor shows the point of contact as being on my Dell XPS 12.

  Try this...

  * Unplug the two computer screens
  * Reconnect the two monitors by USB 3.0 only (do not use DP or HDMI)
  * Use Windows to configure the monitors in extended mode and save this configuration
  * Go to the control panel
  * Contact search
  * Tablet select configuration - installation
  * You will see a screen that says "Touch this screen to identify it as the touch screen if it is not the press serigraphy tablet PC enter to move to the next screen.
  * At this point, press enter
  * This message will move to one of the external screens
  * Press the screen near the message until the message "press on enter to move to the next step in your configuration to compete."
  * Press enter
  * At this point, if only using a screen external, you will be on the tablet settings screen and you can close it. If you use several external displays, the original message will be then posted on other external display
  * You will see a display on the other monitor that says "Touch this screen to identify it as the touch screen if it is not the press serigraphy tablet PC enter to move to the next screen.
  * At this point, press enter
  * This message will move to one of the external screens
  * Press the screen near the message until the message "press on enter to move to the next step in your configuration to compete."
  * Close this window
  * Now every touch screen will work independently without affecting the other or the laptop screen

• Three monitors in Speedgrade?

  I work with three monitors in first, Media Composer, Final Cut Pro, even PhotoShop (sort of). No there is no way to use my third monitor in Speedgrade? Currently, I can use my HDMI TV to view the enlarged image, and one of my computer monitors for the interface, but with all the windows of beautiful, invaluable in Speedgrade, it would really help if I could spread out them between both of my computer monitors. Is there really no way to do this?

  Martin

  OS X.9.5

  2015.0.1 release

  N ° more pity, unfortunately. SpeedGrade only supports 2 monitors... one for user interface, one for the program monitor. And you're not the first to hit this... Let's say a decent number of professional colorists run three monitors... large monitor broadcast-tv for the customer looks at a main interface and monitor of the program "small". I've heard say that linking the right external boxes BlackMagic or whoever can't mount this... but it's two points of view the monitor program and only with a graphical interface.

  Please feel encouraged to make a feature request on this... these things are what is read by the types of bean-counter who allocate resources for engineering teams. They "see" never forums user here.

  https://www.Adobe.com/cfusion/mmForm/index.cfm?name=wishform

  Neil

• Three monitors

  I have a desktop pavilion p6320y with Windows 7 64 bit. The graphics card is integrated (nvidia geforce 9100) and I was wondering what I need to run three monitors. I know that I need a new video card, probably both. Is it possible to run two cards in this computer? Is there a better way to do it?

  Hi tim,.

  This XFX AMD 6850is on sale for $120 after rebate. It supportsAMD Eyefintyand 3 + monitors.

  The Corsair CX600is on sale for $49 after rebate.

  ' HP ' how-to ' articles should be useful.

  When you use AMD EyeFinity, a monitor must be native display connected port or you need to use an asset for AMD EyeFinity validated dongleon a monitor.

• How can I connect three monitors in my desire to hp h8-1534

  Hello

  Im trying to hook up 3 monitors to my new desktop. I just ordered an hdmi cable to vga for the second monitor. The view port on the rear however confuses me. Where can I find this cable? can't find it anywhere. Also it will allow me to have 3 separate screens of desktops to work on?

  HP sells here. Display port HDMI.  The specifications for the Videocard to say it supports up to three monitors.  Use the EyeFinity for three monitors.

  Kind regards

  ERICO

• Y510P 59405664: Dockingstatin available, even with three monitors?

  Hello

  I am about to replace my desktop and laptop system with the IdeaPad Y510P 59405664 as the two-in-one-solution. So: is there a docking station for this idea which is able to manage the following specifications?

  • mechanical keyboard via PS/2 (not an absolute must, but would be great)
  • mouse via USB
  • audio via RCA
  • three monitors
  • Gigabit ethernet

  I hope that it is possible, even with three monitors. In my current setup of PC desktop, I use three monitors, too. The reason I think that it should be possible is that this IdeaPad has the internal CPU graphics (NVS), who can manage a monitor, and the second dedicated graphics card GT750 that should be able to handle additional monitors. All monitors are monitors FHD (1920 x 1080).

  If there is No docking station available that can handle three monitors, is it possible to work with DisplayPort or something like that? I have not worked with DisplayPort, so I don't know what is possible.

  I appreciate every response that is useful to me :-)

  There is no docking station on the y510p

• Three monitors with FSX Gold and Windows 7?

  How can I configure three monitors with Microsoft Flight Simulator Gold?

  Hello

  You can see the Sub articles that might help you.
  How to configure multiple monitors for Flight Simulator X and other Microsoft Games for Windows games
  http://support.Microsoft.com/kb/240981
  Flight Simulator x: the use of multiple monitors
  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=62E19B18-A649-4AC0-aad3-B90622B1E858&%3Bdisplaylang=en

  I also suggest to contact the Flight Simulator X support team for assistance on this.
  http://support.Microsoft.com/GP/cp_flightsim_master#TAB4

• Try to put in place three monitors for Flight Sim 2009

  How can I configure three monitors with my card vid ATI Radion 6800 (two ports dvi on the back).

  Do I need another card or can I split the signal?

  Gerwin, you will need to buy a new video card. Rami
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Three monitors on a Del Optiplex 7010

  Hello

  I am trying to install three monitors on my Dell Optiplex 7010. I have the graphics card integrated ports (2xDisplayPort, 1xVGA) with you and use a PCI card with two ports (1xDVI, 1xDisplayPort).

  The three monitors I have are out 2xDVI, 1 output VGA x.

  I have been using some converters for my monitors cable to the DisplayPort Concerto to connect them to the Ports on the PC display.

  Both DisplayPort monitors work very well using the integrated graphics card, but the VGA is not. I was told that it is because of the converters I use.

  I tried several different combinations to make it work with no luck: (.)

  Could anyone suggest how I might get this work or what graphics card I would be able to buy to make this work?

  Thank you

  Boldonglen

  Hi Shawn,

  I've been in contact with one of your technical guys and we went through a few diagnostic checks to see why I could not as well integrated graphics card and graphics card dedicated to the work. We finally found a solution. Because I use Windows 8.1, I needed to update my BIOS using this link. Once I updated my BIOS, I went into the BIOS and enabled the multi-screen display box. Once we did, and I restarted my PC I managed to connect monitors for two graphics cards internal and dedicated, and they all work.

  Hope this helps someone.

  Kind regards

  Glen Robson

• Installation of the driver software window opens on the second monitor in a dual monitor extended installation of the monitor

  The "Software Installation" window will open on the second monitor in a dual monitor extended installation of the monitor

  I have a dual display setup. A 225WS 1680 x 1050 monitor LG is connected via a VGA cable and a VGA - DVI converter to a DVI port on a Radeon 6850 video card. The second screen is a Samsung HDTV set at 1920 x 1080 and connected via HDMI on the same video card. I have set up the screen LCD as main monitor and the Samsung HDTV as the extended display. HDTV is most of the time, but I use it at least once a day. This isn't a driver problem, because it happened also when I had an old Nvidia video card and it is fixed by a new installation of windows and setting up of screens from a square.

  The installer works great almost all the time except when I try to use some programs or Windows functions (7). When I try to start the MozBackup application or I pop in a new usb device and click on the notification bubble, both these windows (MozBackup and the "Driver software Installation" window) open in the center of the HDTV as opposed to the LCD (which is defined as primary). The problem is that the views are ~ 3 meters out and HDTV is mostly off.

  I sent a bug report to the developer of MozBackup because this part is perhaps a problem with its software or what old Windows functions and hooks it uses, but the window "Installing the driver software" (or who knows what other program Windows Basic) has exactly the same problem and is part of Windows.

  What can I do about it? I DIDN'T put the displays in any mode "clone" to have office in mirror between them. Is - this fixable somehow? I guess that is not a problem with the video card drivers because I used two different video cards with either the manufacturer or windows update drivers and the problem is the same.

  I'm talking about a window similar to this one
   
  http://jaunty-electronics.com/blog/wp-content/uploads/2012/09/Freedom_FRDM-KL25Z_driver_install.PNG

  Try changing the backup.ini

  you find it in

  .. \Program files (x86)\MozBackup\backup.ini

  Open the file backup.ini with editor

  Check if you have the rights to save the changed files in this directory. You may need to change the Directory rights

  Change the value of "1": monitor

  wyzodir =

  ; Monitor: the monitor number where MozBackup window will appear

  monitor =1

  '2' or whatever the value of your primary monitor is:

  wyzodir =

  ; Monitor: the monitor number where MozBackup window will appear

  monitor =2

  System main screen could be identified as '1 '. If you have changed the monitors, it can be used internally '2 '.

• Three monitors on two AMD Radeon HD7470 video cards

  I just got a Minitour OptiPlex 9010 with 2 dual AMD Radeon HD7470 1 GB graphics cards.  When I placed my order, I told them that I wanted to connect three monitors.  The VGA port has been inactive for other video cards have been installed.  I've been on technical support for more than three hours, when they finally decided to send a tech.  He was released the next day and told me that I needed a split adapter.  I ordered an and he hung up but there was showed the same jobs and I was unable to make changes to the resolution, etc.  Video cards have a DVI and a displayport.  I can connect a DVI monitor and others in the displayport and the monitor then third on the second video card?  Or can I just add another video card to the Tower?  Any help would be greatly appreciated.  Thank you!

  Hi pbondcb,

  You must connect the first monitor to the DVI port and the second for the DisplayPort on the first graphics card. The second monitor must be connected to the DisplayPort with the appropriate cable. You can connect the monitor third DVI port on the second graphics card.  You must enable the display via the Catalyst Control Center under Windows, using the Eyefinity function. The third monitor works only in Windows.

  I hope you find this information useful.

  Please reply to this message if you need help.

• Three monitors W/laptop using the USB device

  I am trying to run three monitors, I have a VGA to TV connection and I have an external graphics device (USB) which will reflect only my office instead of expand it and it doesn't work if I disconnect my VGA cable.  It worked correctly only twice, and then comes back to what I just said.

  I am trying to run three monitors, I have a VGA to TV connection and I have an external graphics device (USB) which will reflect only my office instead of expand it and it doesn't work if I disconnect my VGA cable.  It worked correctly only twice, and then comes back to what I just said.

  Thanks MS, I went threw the control panel and Setup for three monitors works fine now.

• Three monitors/vGPU profile

  What is the profile of minimum vGPU to support three monitors on NVIDIA GRID K2? Thanks in advance for your help.

  HI - you need K260Q or K280Q profile. The two profiles supports up to 4 monitors (2560 x 1600).

  I would like to start with a K260Q profile for more density. What applications do you intend to operate?

• Installation of the monitor three Lenovo E550?

  OK, so I have a Lenovo E550 and OneLink Pro Docking Station (the one with the RFP, and DVI Ports).

  So when I got to my laptop, I was able to connect successfully three external monitors to your laptop. 1 using the VGA Port on the side of the laptop and then using the DP and DVI ports. (I close my laptop and turn off the laptop screen). However this provoked touching every two seconds. I honestly didn't mind, because it is a work laptop and I do not have anything too serious on this subject.

  Now however I can't even use the VGA monitor if the onelink is attached. It will be either twinkle extremely fast, or just simply stay black. If I disconnect the Onelink however I use the monitor perfectly.

  I thought the solution would be to switch to the use of the HDMI Port, but it would seem that the HDMI Port is disabled when the OneLink is plugged in, because I don't get a signal on my HDMI Port when the OneLink is connected, if I disconnect the OneLink if my HDMI works perfectly well.

  So is there any way to get this configuration works correctly? I've updated all the drivers and firmware, I switched to a different E550, I swapped a different OneLink and a different charger for the OneLink and it seems that the problem persists through on everything.

  Thanks for any help!

  In response to customer relationships of flickering or flashing on external monitors connected to E550 laptop via VGA, a CUTTING-EDGE Service port was released.

  It can be found here: https://support.lenovo.com/us/en/documents/SF15-T0074

  Thank you