HP Color Laser Jet CP2025: double-sided printing disabled in Windows 10

I just upgraded to Windows 10 and downloaded the latest driver for my printer. I can't find any setting of double-sided printing. Is there something that I am missing. I tried to download the Toolbox, but it does not work on a 64-bit computer.

The function "automatic detection" used by some (Windows) drivers on the install (or update) does not always; make sure the driver knows that a duplex unit is present on the printer (assuming that a single is present):

  • For the instance of the printer in question, bring up the printer properties dialogue.
  • Select the device settings tab.
  • Make sure the duplex unit is set to installed and not installed.

You will probably need to be logged in with administrator credentials in order to change the settings of the device.

Tags: HP Printers

Similar Questions

  • HP Color Laser Jet CM6040: scratches when printing CM6040

    I have a very annoying problem with my print quality which causes the color to the burrs. Whenever I have print something on my laser jet CM6040 color it leaves a strip of color at the top of the page that spots and affects all pages.
    Recently it was also printing this band at the bottom of the page that you can see in the picture as an attachment. It tends to be worse in the morning when I get to work and first print something and tends to be bad after sitting idle for a while. We have installed a new fusion kit fairly recently so would avoid buying another so soon.

    Can anyone help or everyone knows that before?

    Think about how the image is made on paper. The flow of paper to the top of the side of the printer tray and a secondary transfer roller moves the image of the belt (just the little strip of paper feeds more) in order to fill the document with the complete picture. Continutes to travel at the front of the belt is a wiper brush that removes the residual toner was not transferred to the book and the back side of the belt if another page is printing is the image placed on it as the belt moves on the toner drums. If the belt has a defect in the Wiper Blade, excess toner that is a mixture of all colours (usually purple in color) out of the end of the belt like a streak. That's what I think happens for you. Now one thing you can try who works occasionally for me is to spend about 1 inch belt in the opposite direction, which will expose a lot of toner on the belt. Clean the toner and then advance the belt (always use the edges of the belt to move) and then look below where the belt comes out from the front and see if the line is still present or that it is a party. If passed, then the blade may have corrected itself. If the lines are still present, the blade is bad and the belt needs to be replaced. The cost of the belt is high. You could contact a company like metrofuser.com that may or may not sell belt given to nine for your model see if they have your model in stock. The cost is generally 1/2 of what you have to pay for a new belt, but you will need to return the old belt to them.

  • HPlaserjet3390: My Laserjet 3390 offers more double-sided printing after upgrading windows 10

    My all-in-one worked perfectly but after windows upgrade 10 I can't solitaire to print double-sided and does not

    as one more option.

    How can I get print double sided once again.

    Make sure the driver knows that a duplex unit is present on the printer (assuming that one is):

    • For the instance of the printer in question, bring up the printer properties dialogue.
    • Select the device settings tab.
    • Make sure the duplex unit is set to installed and not installed.

    You will probably need to be logged in with administrator credentials in order to change the settings of the device.

    If the device does not have a double-sided hardware unit, then you can not do Automatic duplexing, but you should be able to do duplex printing Manual (print odd sides, reinsert the paper print same sides) if the demand for source document and printer driver supports this.

  • Color Laser Jet MFP M277dw Pro: Printer ask a password?

    When I try to access my screen settings touch printer it asks a password (not the past already tried wireless network).  I do not remember a definition, but if I were to set to the top I forgot and to know how to find or how to reset.  Thanks in advance for the help!

    Hey @ssullivan,

    Welcome to the HP forums! I hope you enjoy your stay here.

    I understand that you have a password on your Laserjet M277. To move only the printer will probably need to have a factory reset done on this. To do this, you need to contact HP support. You can contact HP support by clicking here and filling out the form below.

    I hope that you are able to remove this password set and I hope you have a nice day!

    If this solves your problem then please help others to find this post by clicking on accept as Solution on my post.

    If you appreciate my help so please let others know by clicking on the icon below my post thumbs up.

  • Color Laser Jet MFP M177fw Pro: Printer is not recognized by the devices.

    When connected to a computer via the usb - B to usb at the back of the device connection, computers do not get a signal telling them that they are connected to anything. The computer windows 7 behaves as there is nothing plugged and a Mac running 10.9.5 simply gives the error message "the disk you inserted is not readable by this computer. When I try to download the drivers for the device manually, the installation of HP can't find the printer in the devices, even when it is plugged. Both computers have been restarted, several cables (who work for other printers and are located in the length of HP limit) are the same exact behavior.

    Solution has been found, windows 7 update, but a driver do not go along, while some things have worked when it is plugged. HP partner, effects no side windows just weird.

    For those who read this topic after googling their problems: updated all the drivers. EACH OF THEM.

  • Please help - installation Color Laser Jet 1600 without disc printer

    HI -.

    Really hoping that someone can put this issue to bed for me, because I spent all afternoon trying to solve this one.  I work in an elementary school as the Co-ordinator CT, one of the teachers what is the printer of the staff to settle on his laptop in the classroom, but hey guess what the disc facility is not the case to be found.  heard you can load it it from the Internet, is this correct and if so, how do I and where do I find the correct Web page.

    Thanks in advance.

    Click HERE

  • Officepro jet 8600: double-sided printing

    What I really wanted to say, is that it is the function copy/zeroxing biased, I can't seem to get.

    To add more, once the setting of the option as Original 1 sided: one copy, you can type set as the new default value in the same menu and confirm to set 1 back copy as default for future copy jobs.

  • Color Laser Jet MFP M277 Pro: Can I scan a document on the HP MFP M277 Color LaserJet Pro printer double-sided?

    Hello

    What I can and, if so, how to scan a document double sided on the Color Laser Jet Pro M277 HP printer MFP?

    Thank you very much

    Paul

    Hello

    No, it only supports printing double-sided, recto verso but scan copy not duplex from the Manual:

    http://h10032.www1.HP.com/CTG/manual/c04474163.PDF

    Kind regards.

  • Laser Jet Pro M402dn: Double-sided printing

    I need to know how to double-sided printing. I know that this printer can do. But how?

    The function "automatic detection" used by some drivers on the install (or update) does not always; make sure the driver knows that a duplex unit is present on the printer (assuming that a single is present):

    • For the instance of the printer in question, bring up the printer properties dialogue.
    • Select the device settings tab.
    • Make sure the duplex unit is set to installed and not installed.

    You will probably need to be logged in with administrator credentials in order to change the settings of the device.

  • HP Color Laser Jet CP1215: print - guard 'book light' flashing - printer stops charging of paper does not alter

    Hello!

    For about a week, I have the following problem with my HP Color Laser Jet CP1215: after 2-3 pages of printing, the device stops abruptly in the middle of a job and the light number 5 (paper) continues at the flashing light.

    However, the bin is full with paper.

    Ignitions and extinctions help only for another 2-3 pages, then printing will stop again as described above.

    Is there maybe a photoelectric cell that needs to be cleaned or a mechanical part that gives the status of bad paper from the paper tray to the printer?

    Thanks in advance for any help,

    Best wishes

    Herwig

    Hi @wigl,

    Welcome to the Forums of HP Support!

    I see that your HP Color LaserJet CP1215 printer stops printing when the print jobs. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

    I can see how frustrating it would be. To determine the cause, we need to use more than one document. Redundant that some steps may seem, I would execute all.

    Please, try the steps in this these guides:

    If the problem persists, try a hard reset:

    • Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
    • Reconnect the power cable to the output of the printer and the wall, and not a surge protector. This ensures that the printer is full on and can help this situation.
    • Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

    Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

  • Color Laser JEt MFP M477fd Pro: automatic update of ruined printers print

    My new laser Jet worked very well until I followed the instructions on the printer for an automatic update. Now print is ruined. Page layout is described in gray, and look bad color photos. This happened DIRECTLY after that I said yes to the screen to update printer on the printer itself. I did not change my Mac.

    I tried closing printer, computer shutdown, and then restart the printer, then restart the computer.

    The Configuration report (can barely read.) Firmware Datacode says: 20160331, which is apparently the most recent printing for my model software.

    I'm on a Mac 10.10

    Color Laser Jet Pro MFP M477fdw, bought end of 2015.

    The printer was so easy to set up and worked wonders for 200 pages that I sent to him so far, until I said yes to an update. Wish really to say yes to that, but I just assumed it would work as well as everything else.

    Thank you for your help to solve this.

    After trying countless things, including uninstalling and reinstalling the printer and download the latest driver, I called Technical Support. The number is on the internet, not on HP. 800-334-5144 where you need it. They continue to try to trick you online, but eventually, you get to someone who can help.

    When I described the print results, I was getting, she had me do the cleaning Page, 3 x and 3 x color calibration, which corrects the problem.

    The problem of updating firmware with the trainer, is what I * think * she said.

    If your printer works fine... DON'T let NOT download an update.

    It has been long since I've owned a laser printer. Lesson learned. Thank you, Natasha.

  • How to get a hp 4600 Color Laser jet print on a vista or Windows 7 64 - bit OS PC which does not have a parallel port connection?

    My hp 4600 color Laser Jet uses a parallel cable to connect to a Windows PC. When I had XP as the OS it worked fine. But now after the upgrade to Vista or Windows 7 64-bit OS it will not work and my PC does not even recognize it when it is plugged into the PC with the parallel to USB cable that worked so well before. So, what should I do to get the PC to recognize the Hp 4600 and have it printed again as before? (My first plan is to try to get the printer to work by hooking up through Wireless. Does anyone know if it will work? I'll answer my own question, if it does. Wish me luck! (Thank you!)

    According to the HP support site, there are drivers available for Vista and Windows 7 If you're lucky it. Download the appropriate drivers for your computers. According to the information of product from HP, this printer can be connected directly to the network by an ethernet cable. I don't see where it has wireless capability, but in any case ethernet is preferable for printer connections if possible.

    Connect the printer directly to your router or switch connected to your router and assign a static IP address outside the range the router DHCP. Then, install the drivers that you got from the HP website for your operating system.

    MS - MVP - Elephant Boy computers - don't panic!

  • Print Page of cleaning HP Color Laser Jet CP1215 problem

    I have a HP Color Laser Jet CP1215 connected to a Windows7 64 bit operating system. The printer prints the shadows cast on the left and right of the paper edges, but also the light shadows in the printing.  I saw the HP Toolbox for my printer and tried to print a cleaning page.  All I get is a text box indicating that the printer could not be accessed, even if it will calibrate and print a test page. I need different drivers or is there another solution?

    Hi eitooc,

    Welcome to the HP Forums, I hope you enjoy your experience!

    I understand that you found shadows on the page when printing.

    I'll be happy to help you.

    The driver may be corrupted not allowing all the features work.

    There could be a problem with the toner or the fuser unit causing this problem.

    Make sure the printer is connected directly to a wall outlet and the USB cable is connected directly to the computer. Try running Cleanup again.

    Here is a document to solve problems of quality Print. Follow the steps to see if that will help solve the problem.

    If you still have problems you can uninstall and reinstall the latest version of the software.

    HP Color LaserJet CP1215 Printer Drivers. Select the operating system, and then click Next.
    Click on driver - product Installation software and download the drivers.

    Then try to re-run the cleanup page.

    This happens with all applications?

    What kind of paper do you use?

    You use genuine HP toner?

    I hope this helps.

    Thanks for posting on the HP Forums.
    Have a great weekend!

  • HP Color Laser Jet 1600 in grayscale only print

    Using Windows 7, photographs BOF emails only print in grayscale. The image is in color but in grayscale when played back before printing. What adjustments should be made?

    Hi Mike,

    Thanks for posting your query in Microsoft Community.

    From your description, it seems that photographs in color of emails only print grayscale to HP Color Laser Jet 1600 printer.

    I'll be happy to help you. This problem could be caused because printer settings can change to grayscale and need to change print or as default settings.

    I would be grateful if you could answer the following question:

    1 have you changed any settings in your printer software?

    2. which webmail client or by e-mail you are talking about?

    3. What is the file format of the image?

    4. What if the problem persists for photos in the computer?

    I suggest to follow the steps below and we update on the State of the question.

     

    Solve printer problems:

    http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

     

    Choose the printing options:

    http://Windows.Microsoft.com/en-AU/Windows7/choosing-print-options

    For all windows questions do not hesitate to contact us and we will be happy to help you.

  • Printer HP CP1525nw Color Laser Jet not print wireless with Win 7.

    My HP CP1525nw Color Laser Jet printer will not print wireless with Win 7. It is not recognized as a wireless device when by Win7 'add a device '. It has worked very well in the past, but now I have to connect the printer with a cable to be able to print.

    Thank you in advance for your help!

    Sakii305

    Hi Sakii305,

    Thanks for posting your query in Microsoft Communities. The problem description, I understand that you are not able to print wireless. Provide the following information:

    ·         Did you do changes on the computer before the show?

    ·         You get the error message?

    ·         You use a third-party security software?

    Follow these methods.

    Method 1: Temporarily disable the security software .

    Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

    Method 2: Follow the steps in the article.

    Solve printer problems

    You can read this article for more information:

    Why can I not print?

    I hope this helps. Let us know if you need more assistance.

    Thank you.

Maybe you are looking for

  • Satellite A80 - in ODD device with the code 39 error Manager

    Hello I have a Satellite A80 127. I have a problem with my CD player. When I tried to upgrade my XP Home Edition of XP Pro SP2, display said the restart that he couldn't play in my CD player. During the inspection, I found that my CD/DVD drive is una

  • scaling

    Hello. I have an analog input that I am changing. It is to drive a power amp with 0-5 VDC. They would like to have a signal 0-10 VDC, for more information. The amplifier completely leads to 5VDC, even though I placed max = 10 and min = 0 on the DAQ m

  • Alignment incorrect impression

    Original title: print alignment When I print a test page the black alphabet has a red alphabet printed about 1/32 of an inch just below. I need to know how to adjust the print to align the Red cartridge with the rest. Thank you [Moved from comments]

  • Kan man stanga av automatiska our pa beskarning?

    Beskarningen gar mycket trogare och olika value passar aldrig som jag vill ha precise dem. Jag vill bestamma sjalv! SA lange verktyget ar gar allt annat arbete langsammare också mycket aktiverat. JAG bokade att nya versioner skulle innebara förbättri

  • How to open PDF documents in the same window?

    Prof. Acrobat X / Windows:How to manage open PDF documents in the same window?When I open more than a single PDF docs and a second, third,... window opens, each document is opened in a separate window.In previous versions (Acrobat 8 Prof.), all the d